Problem burning red led constantly flashes

  Hi all this is my first post in this forum....( NEWBIE )
as mentioned in subject Problem burning red led constantly flashes then I recieve a message " error reading data"
the dvd burner is a MSI  ms 8404a. using Nero6 and princo DVD -R Win XP-PRO
I have had no problems in the past burning with this media and I'm halfway through a stack of 50...
I dont have any other media here atmo so any help would be great..
Also upgraded firmware with msilive although it said I had the current version..
Cheers in advance ROB
Ok just burnt a cd using nero6 while burning the red led flashed costantly, when finished cd ran perfectly ....??? anyone want ABBA GOLD??
Im sure as  that when I used to burn DVD's the red led was solid not flashing....H E L P ....!

I don't understand why the light would be solid and not flashing when burning.
If this is a common problem, it's a problem for me because i'm about to order two MSI DR16-B DVD-RW drives, tell me, is this the drive you have in your system? The one with the problem?
If so i could use some advance warning of the problems i might face.
The previous post is correct, make sure that your Operating System hasn't put the drive into PIO mode, it should be UDMA Mode 2 at least.

Similar Messages

  • Red LED frequently flashing

    Hi, my girlfriend has a new Curve 8520. Since she got it a few days ago the red LED keeps flashing. It seems to start when she receives a message. She then reads the message, replies etc but the light keeps flashing.
    Is this is a fault or is it a strange setting I need to turn off?
    Thanks

    RED led notifies if you have any unread email, SMS, MMS or missed phone call. If all these are read then this should go off. Moreover, even if you have unread email, SMS, MMS or missed phone call after 15 mins RED led flashing should be stopped.
    I would recommend you to have a battery pull device reset and then check the behavior.
    tanzim                                                                                  
    If your query is resolved then please click on “Accept as Solution”
    Click on the LIKE on the bottom right if the post deserves credit

  • 4 red leds after flashing bios

    I flashed the bios on  k7t266 pro2. After reboot i get 4 red leds and no post. Its acts as if dead. Does this mainboard hve the bios recovery at start-up like the newer ones or am I hosed.

    used the jumper to clear cmos but did not bring back the post and I do have a copy of the old bios but if I can not get a post then I can not use it.

  • Pearl 8130 red led double flash code

    After connecting pearlie to macbook pro desktop dude woke up and screamed "downgrade os." I acknowledged and allowed the system to perform downgrade. Something about software only has certain amount of time before it expires. About 7 minutes into downgrade, dude yells, "cannot continue," screen turns off, led goes red and flashes sequence two on, two on over and over steady. Now I'm cut off from outside world, no phone. Chalk up another one for manmade **bleep**. At least 12 hours ago it did an "all" back up, so if I'm having to replace phone (if chances are there's no remedies on this site) I didn't lose everything. Is this Verizon's control over the phone or R.I.M's built in gotcha, buy another phone already tactics? I'm wondering...
    Is there a list of error code explanations out there that I(we) can reference to fix this? If not, dumb design. Since the verizon tech's phone number is on the phone, can't reach them either. 
    /Users/rickaentenmann/Desktop/8001053Fz29 Juice/gif/index.html

    urumilton wrote:
    The red light flash when you received a new message, mail, etc, but flash for a short time, not for ever.
    And if you don't have any unread message the light is off. 
    No, I know that. What I'm specifically talking about is .....
    Say you turn on your BB and the light flashes green a few times .... then ... nothing. No flashing or anything. Yes, if I get a call or a message, it'll flash red, but isn't it NORMALLY supposed to be flashing green all the time (while you're not talking or doing anything on it)?
    What I'm trying to find out is ...... is it normal for the green LED light (not counting any calls or email messages I may receive) to not flash at all right after you turn the phone on? OR is it actually SUPPOSED to be flashing all the time? Because, if that's the case, I'm worried if I have a faulty LED light in my phone.

  • RED LED STOPS FLASHING AFTER 10 MINS

    Hi,
    I have made sure my phone is set to LED flash when SMS texts come in. And it flashed continually until I read my text msgs up until yesterday. Now it stops flashing after about 10 minutes. Does anyone no why this would happened? I have taken out the battery and rebooted it, but nothing works. I want it to flash continually until I read the msg like it used to.
    Please help!
    Solved!
    Go to Solution.

    Hello RPIGOTT and welcome to the BlackBerry Support Community Forums.
    I would back up your BlackBerry data and clear out your Profiles database.
    If you need the BlackBerry Desktop Manager you can download it here.
    KB23680 will show you how to back your data.
    KB10167 will show you how to clear the Profiles data base
    After you have cleared the database you will have to re-configure your ring tone settings.
    Let me know if you need further assistance.
    -HMthePirate
    Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

  • Red LED Light Remains On

    The battery is fully charged and disconnected from charger.  When hibernating, the red LED light constantly remains on.  When the phone is being used, the red LED light does not appear.
    What is wrong? How can this be fixed?  Thanks much for help.

    I'm a total newbie to smartphones.  Based on your question, I cleared all the Notifications and the red LED disappeared.  Then sent myself an email to test the blue LED light and it is now blinking.  So, the problem might be solved but don;t know why the red LED constantly displayed after charging the battering to 100%.  
    Don't know about Lightflow!
    Thanks

  • Faulty Mac Pro "Red LED" on Processor Tray (not RAM LED)

    Hello.
    I have a faulty Mac Po and wondering if someone can advise.
    There's a red LED constantly switched on on the processor tray (see photos). It is not one of the RAM diagnostic LEDS.
    The Mac Pro does not load up. It does initialise the RAM and boot up the Hard Disks.
    At the same time the Graphics card fan spins very fast, and no input is detected on the display. I have removed it (in the photos) just in case it overheats.
    I have plugged in the graphics card and processor tray on an identical Mac Pro and they both work fine. I have also swapped out the small button-battery fo a new one.
    I have also unplugged all cables, reseated the RAM and removed any non-Apple RAM, leaving the shipped RAM in place.
    If anyone has any ideas what this might be I'd be grateful for a response.
    With thanks in advance
    Lawrence
    Info & Images below:
    Model Name:
    Mac Pro
      Model Identifier:
    MacPro4,1
      Processor Name:
    Quad-Core Intel Xeon
      Processor Speed:
    2.66 GHz
      Number of Processors:
    1
      Total Number of Cores:
    4
      L2 Cache (per Core):
    256 KB
      L3 Cache:
    8 MB
      Memory:
    6 GB
      Processor Interconnect Speed:
    4.8 GT/s
      Boot ROM Version:
    MP41.0081.B07
      SMC Version (system):
    1.39f5
      SMC Version (processor tray):
    1.39f5

    Troubleshooting: My computer won't turn onhttps://support.apple.com/kb/TS1367
    Symptoms
    If your Macintosh computer won't turn on, here's how to troubleshoot it. Please keep in mind that although your computer may display similar symptoms that prevent it from showing video, this article discusses what to do if the computer won't turn on, meaning that when you press the power button:
    You don't hear a startup chime.
    You don't hear any fan or drive noise.
    The power button or power indicator doesn't light up at all.
    If your computer doesn't display any video, it may display one or more of these similar symptoms when you press the power button:
    You may hear a startup chime.
    You may hear fan or drive noise.
    You may see the power button or power indicator light up.
    If any of these conditions occurs, see Troubleshooting: My computer has no video instead. 
    Resolution
    If your computer won't turn on, try each of these steps:
    Make sure that the power cord is plugged into a working wall outlet, and that it's properly connected to the power adapter. (To check if the wall socket is working, plug in a lamp or other electrical device.)
    Make sure that the power adapter is properly connected to the power port on the side or back of the computer.
    Disconnect all accessories that are plugged into the computer, such as a printer, hub, or other mobile device.
    Reset the computer's PMU, SMC, or PRAM. Refer to the instructions for your model:Mac Pro
    reset SMC For "Mac wont' turn on or boot" and related
    https://support.apple.com/kb/TS1367
    Isolating Issues in Mac OShttp://support.apple.com/kb/TS1388
    General purpose Mac troubleshooting guide: Isolating issues in Mac OS X
    Creating a temporary user to isolate user-specific problems: Isolating an issue by using another user account
    Identifying resource hogs and other tips: Using Activity Monitor to read System Memory and determine how much RAM is being used
    Starting the computer in "safe mode": Mac OS X: What is Safe Boot, Safe Mode?
    To identify potential hardware problems: Apple Hardware Test
    General Mac maintenance: Tips to keep your Mac in top form

  • Blackberry 9900 bricked with red LED flashing

    My cell phone Blackberry 9900 was bricked last night. No special usage or status before. Now it can't be turned on any more, just the LED flashing. I have tried many ways to re-turn it on, not work. It even can't connect to computer. the computer is able to find it just when the red LED is lighting!
    What happened on my phone? What can I do next? I must turn it on!

    Hi and Welcome to the Community!
    Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
    With the battery inside, connect your BB to the wall charger
    Leave it alone for 2 hours, no matter what the LED or the display does
    Remove the battery
    Wait 15 minutes
    Insert the battery
    Wait another 2 hours, no matter what the LED or the display does
    This has been known to "kick start" some BBs.
    It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
    Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
    Obtain access to a known good and identical BB...use your battery in it and see what happens
    The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Red LED flashes continuously

    I have the BlackBerry Bold 9650, it's a CPO purchased a year ago, used off and on till June, and has been my primary phone since June.  Up to now it's been fine, and I've gradually added apps and goodies...  Anyway, the last couple of days, it seems when I get a phone call my LED will flash red, endlessly.  I cannot find a way to get it to stop short of pulling the battery, and my battery depletes quickly if I don't do this.  **additional info - the touchpad becomes very sluggish as well, once I receive a phone call after a battery pull.  This is getting to be a bit more than an annoyance, having to pull the battery after every phone call. 
    There have been numerous app updates the last couple of days too, and one was for BeBuzz, so I'm thinking maybe that's the culprit.  It seems to be working normally though (the customized lights for contacts I have set do work) and I've gone through settings and don't see what it could be.
    Anyone else have any ideas?  Or a simpler/faster way to get that red LED to stop flashing? I checked all messages, emails, missed calls, etc and I cannot figure out what is making the LED blink so I can shut it off!!

    MarquiaF_VZW wrote:
    Hi SuzyQ! I'm used to you resolving everyone else's issues, (LOL, yeah, me too!) so I'll be more than happy to help you with your Blackberry. First, I just want to make sure you have the latest software version on your Bold, which was released 1/10. I believe that update was for the 9930 - I've got the 9650.  I am running OS 6.0 and it says my software is up to date.  If not, here are some options to manually download the update and also a list of the benefits of the update. If you do have the update already, do you notice this starting afterwards?
    Do you have any missed calls, voicemails or new emails when this happens? No, I check all of those and cannot find anything I haven't opened or checked!  That's the frustrating part - not knowing why that light is flashing so I can turn it off. Try removing BeBuzz to see if the LED is still flashing and keypad sluggish after receiving calls. I may just have to do that, though I'm using the paid version - I'll back up all my contacts first because I do NOT want to have to set them all up again.  I don't get a lot of phone calls - mostly text and email, but it's annoying when it happens.
    I have not seen any other reports of this issue. If the issue is still occurring after updating software and removing BeBuzz, then I suggest backing up the phone and completing a security wipe on the Blackberry.   Would really rather not go there if I don't have to! Make sure to test making and receiving calls before restoring your data, to make sure no corrupt data is restored. I would recommend backing up just the important info like contacts, calendar, emails, etc.
    MarquiaF_VZW
    Follow us on Twitter @VZWSupport
    Thanks for the response Marquia - I was just thinking it hasn't happened today, but then, I haven't gotten a phone call today either.  So it may still be an issue.  I think I'll wait a few more days and see if it continues to happen or if it was just a weird glitch.  I really am enjoying the Bold, and this is really the first problem I've come up against!  I'll let you know when / if it gets resolved and what works or doesn't work.

  • Luna BH-220 Flashing red led for hours

    I just received my two Luna head sets. The first one charged up fine and did the NFC pair no problem, but the second unit seems to be having a problem.
    The second one just flashes the red led when it is in the cradle. The Led on the cradle is green. The red led on the ear piece turns off if I remove the charger, but just returns to flashing when I plug it back in. This has gone on for the past 5 hours. How do I get this unit reset? What does the flashing LED mean? Both units had very sparse information in the box and I can not find the user manual anywhere on the Nokia support site. The Luna isn't even listed in the support accesories section. Maybe it's too new??.
    Solved!
    Go to Solution.

    UPDATE: finally managed to get nokia to return my THIRD broken nokia bh-220 bluetooth device, as I purchased it from amazon.
    Filled out the necessary online form and sent it to FONEBIZ for the repair (authorised nokia repairs).
    Two days later, I receive a phone call saying that the device is NOT covered and I am to pay a whopping $170 for them to REPLACE my green device for a BLACK ONE. (See attached photo for proof). Please bare in mind that I only paid $57 for my green nokia luna BRAND NEW. So where FONEBIZ get thier estimate from is simply outrageous.
    When I contacted Nokia, they said their customer service represented was wrong, and she shouldn't have given me the details to return the item. Once again NOKIA, WHERE ARE YOUR BRAINS HERE.?
    NOTE
    DO NOT BUY NOKIA PRODUCTS PERIOD
    DO NOT RETURN ITEMS TO FONEBIZ THEY WILL SIMPLY RIP YOU OFF, AND ARE CLEARLY INCOMPETENT AT REPAIRING BLUETOOTH DEVICES. SO I WOULDN'T EVEN ATTEMPT TO LET THEM REPAIR A PHONE.
    NEVER EVER AGAIN WILL ME OR MY FAMILY PURCHASE A NOKIA PRODUCT. I AM DISGUSTED WITH THEM.
    And I encourage, whoever is reading this, to just acknowledge she sheer hell I've been through just for a simple cheap bluetooth device, and just make sure your aware of the risk when buying a more expensive product. Nokia didn't give a second thought to my bad luck. Why would they treat you any different.
    WE ARE JUST MONEY TO THEM...
    Attachments:
    image.jpg ‏56 KB

  • S750: control pod flashing red led READ AND HELP!

    Hi, basically my S750 set of speakers isnt working correctly. When im listening to music and start to pump the voloume up it just stops and the control pod goes back to standy mode with the red led light. Sometime it keeps flashing and I can hear a clicking noise coming from the sub, when the control pod was flashing and the sub was making a clicking noise i looked at the back and saw the green light flickering. Can anybody help me please

    I did thing is its really a lot of hassle. Im based in England, and I need to call a number in dublin (International call) and then pay 6.75 to a 'tutoring session' which will last 30 minutes. That's why I was trying to resolve my problem on here, they don't even know what it could be either. I have dropped my control pod a few times on the floor, so i don't know if it could be faulty now, like a wire may have come loose inside,but then that doesn't explain when i try and play fall power it all cuts out,what do you think?

  • Download dictionary within Kindle app causes Notification red LED flashes like crazy

    I'm not sure if it's a Kindle issue or BB10 OS issue, but it was kind interesting on my Z10 when it happened.
    I've installed the Kindle app from  appworld and I downloaded a free book, touch any content would prompt to download a dictionay for it, confirm it and the Notification red LED started to flash like crazy until the download was completed.
    Have a great weekend.

    It must have been a thriller that you were downloading 'cause you don't get that from heavy drama novels. 
    - If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

  • HT3180 My Apple TV is just showing the apple on a black screen. The led is flashing constantly???

    My Apple TV is just showing an apple on a black screen. The led is constantly flashing???

    Welcome to the Apple Community.
    Which Apple TV do you have.

  • My brand new MacBook Pro retina display not charging the battery any more after 3 weeks...no green or red Led. Any one now about this problem? Thanks

    My brand new MacBook Pro retina display not charging the battery any more after 3 weeks...no green or red Led. Any one now about this problem? Thanks

    Either the power brick is damaged, or the charging circuit is on the blink, or both. Either way, a trip to the Apple Store or the Apple Authorized Service Provider is in order, as this ain't no bargain basement toy.
    In the meantime, can attempt an SMC Reset to see if it helps.

  • BlackBerry Z3 does not Boot, red LED Light is flashing 1x long and after 6x short

    After updating my Blackbery Z3 to 10.3.1.1779, my device won't boot and  red LED Light is flashing 1x long and after 6x short. Need help to solve the issue. Thanks in advance.

    Thank you for your update.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

Maybe you are looking for