Problem changing memory voltage

i was wondering how i can change the memory voltage in the bios of my k7n2-l.  Right now my memory is maxing at 185 fsb and i want to chagne the voltage a little, but no matter how much i change it to 2.7(thats the highest my mobo will go) it always goes back to 2.6 automatically no matter if its on high performance, manual, or spd settings.  If anyone knows how to solve this problem your comments would be greatly appreciated.
2400xp+ @ 2.31ghz (12.5 x 185)
MSI K7N2-L
volcano 9 CPU hsf
512 2700 DDR @ 5-3-3-2.0
built by ATI 9500pro @ 350/321

Quote
Originally posted by saliq82
i was wondering how i can change the memory voltage in the bios of my k7n2-l.  Right now my memory is maxing at 185 fsb and i want to chagne the voltage a little, but no matter how much i change it to 2.7(thats the highest my mobo will go) it always goes back to 2.6 automatically no matter if its on high performance, manual, or spd settings.  If anyone knows how to solve this problem your comments would be greatly appreciated.
2400xp+ @ 2.31ghz (12.5 x 185)
MSI K7N2-L
volcano 9 CPU hsf
512 2700 DDR @ 5-3-3-2.0
built by ATI 9500pro @ 350/321
You can't.  Wait for the next bios update.

Similar Messages

  • MSI Mainboard S-775 X48 - Problems with memory, i think

    MSI Mainboard S-775 X48
    INTEL Core 2 Quad Q6700 2.67GHz
    MSI GeForce 9800GTX 512MB GDDR3
    OCZ TECH DDR3 4GB ( OCZ TECH DDR3 PC3-12800 1600MHz Platinum XTC Dual Channel 2GB Kit(2x1024MB) 7-7-7 (OCZ3P16002GK))
    THERMALTAKE 750W ToughPower
    Hello.
    I have bought a new computer a week ago.
    First time i started the computer, two of the light diodes on the ram slot 3 and 4 was red. And have been ever since.
    The bios was on default, and the computer freezez now and then, maybe every hour or something. I tried to take out the 3 and 4 memory module and set the memory volt on 1.9. And everything worked very fine.
    So i tought maybe i should innstall the other two again. And now the computer is just unstable, artifacts in games, suddenly's restart's m.m.
    i know its something about "spd" ,but that its way over my league.
    So my questions, what is the right numbers to fill inn. ? and is it because of the memroy i have this problems?
    Appriciate all the help, and sorry for bad english.
    is this good enough?
    Memory Frequency   534.0 MHz (1:2)
    CAS#         7.0
    RAS# to CAS#      6
    RAS# Precharge      6
    Cycle Time (tRAS)   15
    Command Rate      1T
    Quote
      CPU-Z version 1.45
    Processors Map
    Number of processors   1
    Number of threads   4
    Processor 0
        -- Core 0
            -- Thread 0
        -- Core 1
            -- Thread 0
        -- Core 2
            -- Thread 0
        -- Core 3
            -- Thread 0
    Processors Information
    Processor 1 (ID = 0)
    Number of cores      4 (max 4)
    Number of threads   4 (max 4)
    Name         Intel Core 2 Quad Q6700
    Codename      Kentsfield
    Specification      Intel(R) Core(TM)2 Quad CPU    Q6700  @ 2.66GHz
    Package         Socket 775 LGA (platform ID = 4h)
    CPUID         6.F.B
    Extended CPUID      6.F
    Core Stepping      G0
    Technology      65 nm
    Core Speed      2670.2 MHz (10.0 x 267.0 MHz)
    Rated Bus speed      1068.1 MHz
    Stock frequency      2666 MHz
    Instructions sets   MMX, SSE, SSE2, SSE3, SSSE3, EM64T
    L1 Data cache      4 x 32 KBytes, 8-way set associative, 64-byte line size
    L1 Instruction cache   4 x 32 KBytes, 8-way set associative, 64-byte line size
    L2 cache      2 x 4096 KBytes, 16-way set associative, 64-byte line size
    FID/VID Control      yes
    FID range      6.0x - 10.0x
    max VID         1.263 V
    Features      , VT
    Chipset
    Northbridge      Intel X48 rev. 01
    Southbridge      Intel 82801IR (ICH9R) rev. 02
    Graphic Interface   PCI-Express
    PCI-E Link Width   x16
    PCI-E Max Link Width   x16
    Memory Type      DDR3
    Memory Size      4096 MBytes
    Channels      Dual (Symmetric)
    Memory Frequency   534.0 MHz (1:2)
    CAS#         7.0
    RAS# to CAS#      6
    RAS# Precharge      6
    Cycle Time (tRAS)   15
    Command Rate      1T
    Memory SPD
    DIMM #1
    General
    Memory type      DDR3
    Module format      UDIMM
    Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
    Size         1024 MBytes
    Max bandwidth      PC3-10700F (667 MHz)
    Part number      OCZ3P16001G       
    Manufacturing date   Week 28/Year 07
    Attributes
    Number of banks      8
    Nominal Voltage      1.50 Volts
    EPP         no
    XMP         no
    Timings table
    Frequency (MHz)      476   571   667   762   857   
    CAS#         5.0   6.0   7.0   8.0   9.0   
    RAS# to CAS# delay   5   6   8   9   9   
    RAS# Precharge      5   6   8   9   9   
    TRAS         15   18   21   23   26   
    TRC         20   24   28   32   36   
    DIMM #2
    General
    Memory type      DDR3
    Module format      UDIMM
    Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
    Size         1024 MBytes
    Max bandwidth      PC3-10700F (667 MHz)
    Part number      OCZ3P16001G       
    Manufacturing date   Week 28/Year 07
    Attributes
    Number of banks      8
    Nominal Voltage      1.50 Volts
    EPP         no
    XMP         no
    Timings table
    Frequency (MHz)      476   571   667   762   857   
    CAS#         5.0   6.0   7.0   8.0   9.0   
    RAS# to CAS# delay   5   6   8   9   9   
    RAS# Precharge      5   6   8   9   9   
    TRAS         15   18   21   23   26   
    TRC         20   24   28   32   36   
    DIMM #3
    General
    Memory type      DDR3
    Module format      UDIMM
    Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
    Size         1024 MBytes
    Max bandwidth      PC3-10700F (667 MHz)
    Part number      OCZ3P16001G       
    Manufacturing date   Week 28/Year 07
    Attributes
    Number of banks      8
    Nominal Voltage      1.50 Volts
    EPP         no
    XMP         no
    Timings table
    Frequency (MHz)      476   571   667   762   857   
    CAS#         5.0   6.0   7.0   8.0   9.0   
    RAS# to CAS# delay   5   6   8   9   9   
    RAS# Precharge      5   6   8   9   9   
    TRAS         15   18   21   23   26   
    TRC         20   24   28   32   36   
    DIMM #4
    General
    Memory type      DDR3
    Module format      UDIMM
    Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
    Size         1024 MBytes
    Max bandwidth      PC3-10700F (667 MHz)
    Part number      OCZ3P16001G       
    Manufacturing date   Week 28/Year 07
    Attributes
    Number of banks      8
    Nominal Voltage      1.50 Volts
    EPP         no
    XMP         no
    Timings table
    Frequency (MHz)      476   571   667   762   857   
    CAS#         5.0   6.0   7.0   8.0   9.0   
    RAS# to CAS# delay   5   6   8   9   9   
    RAS# Precharge      5   6   8   9   9   
    TRAS         15   18   21   23   26   
    TRC         20   24   28   32   36   
    Hardware monitor
    Fintek F71882F hardware monitor
    Voltage sensor 0   3.33 Volts [0xD0] (+3.3V)
    Voltage sensor 1   1.23 Volts [0x9A] (CPU VCORE)
    Voltage sensor 2   0.31 Volts [0x27] (VIN2)
    Voltage sensor 3   0.98 Volts [0x7B] (VIN3)
    Voltage sensor 4   0.97 Volts [0x79] (VIN4)
    Voltage sensor 5   1.10 Volts [0x89] (VIN5)
    Voltage sensor 6   1.51 Volts [0xBD] (VIN6)
    Voltage sensor 7   3.33 Volts [0xD0] (VSB3V)
    Voltage sensor 8   3.20 Volts [0xC8] (VBAT)
    Temperature sensor 0   40°C (103°F) [0x28] (TMPIN0)
    Temperature sensor 1   37°C (98°F) [0x25] (TMPIN1)
    Temperature sensor 2   49°C (120°F) [0x31] (TMPIN2)
    Fan sensor 0      2019 RPM [0x2E7] (FANIN0)
    Hardware monitor
    Intel Core 2 Quad Q6700 hardware monitor
    Temperature sensor 0   44°C (111°F) [0x38] (core #0)
    Temperature sensor 1   42°C (107°F) [0x3A] (core #1)
    Temperature sensor 2   38°C (100°F) [0x3E] (core #2)
    Temperature sensor 3   36°C (96°F) [0x40] (core #3)
    Dump hardware monitor
    Hardware monitor
    GeForce 9800 GTX hardware monitor
    Temperature sensor 0   58°C (136°F) [0x3A] (GPU Core)

    I think you are going to need to go into the bios and manually set the memory voltage and the memory settings.
    Try setting the memory voltage in the bios to 1.9 and then manually set the memory settings to 7-7-7-20 and see if that works.  If not; then change the memory settings 8-8-8-21 and see if that helps.  You might also need to up the northbridge voltage a notch or two since you are running memory in all four slots.
    Psy

  • Memory Voltage X58 Platinum

    Hi,
    I recently bought 2 GTX 460's to SLI with my X58 Platinum. I have been having lock ups while gaming that sometimes include white blocks all over the screen. EVGA tech support has told me to ensure my ram timings and voltages are set correctly for the RAM I use to ensure stability. The memory model I use is OCZ3G1333LV6GK. I changed the timings to 9-9-9-20, but I was unable to change the voltage from 1.5 to the recommended 1.65. The option was greyed out and the BIOS stated that changing the voltage to 1.65 could potentially damage the cpu.
    Can I/Should I find a way to force the voltage up? Is this the incorrect RAM/Mobo Combination? What do you all think?

    Quote
    The option was greyed out
    Use the +/- keys of your keyboard's numpad.
    Quote
    and the BIOS stated that changing the voltage to 1.65 could potentially damage the cpu.
    1.65V is the absolute maximum Intel has defined for DRAM voltage.  Ignore the warning. 

  • How can I programmatically change the voltage range settings in a DAQ Assistant

    Hi,
    First post here.  
    I need to be able to change the voltage range properties of a daqmx DAQ Assistant based on user input.  My hardware, an SCXI-1102C does not allow changing this property on a running task, so I'd like to either set the analog input voltage range before the DAQ Assistant activates, or pause the DAQ Assistant immediately after it starts, set the values and then resume.
    I don't know how to edit the task ahead of time because the DAQ assistant creates the task when it runs, and there is no task before that.
    In the attached picture, I have a conditional section, set to run only if the while loop iteration is 0.  I take the task from the Daq assistant, send it to a stop task vi, set the property, and then send the task on to the start task vi. I can watch it run with the debug light on, and everything seems to work correctly, but on the second (and all the other) iteration of the loop, I read out AI.Max and it seems like the DAQ Assistant has re set it back to 5V.  Can anyone see what is going wrong here?
    BTW, this is continuous acquisition and the code does not produce error messages when it runs.
    I did come across a similar question that someone posted here back in 2006, but his question was specifically aimed at a Labview API (VB, I think), and not an actual G solution.
    Attached are the actual vi in question and a png image of the block diagram.
    Thanks! 
    Ruby K
    Solved!
    Go to Solution.
    Attachments:
    Labview_question.PNG ‏14 KB
    Sample_AIV.vi ‏91 KB

    First, if you want to start getting beyond the basics with DAQ, you are going to have to stop using the DAQ assistant and do it with lower level DAQmx VI's.  There are hundreds of examples in the example finder.  You can even right click on the DAQ assistant and select open front panel.  That will create a subVI that you can open and see what is going on behind the scenes.  Do it.  I think you'll find the DAQ task is being recreated on each (though I'm not 100% of how the settings are established or maintained in each section of that subVI).
    The second problem is you have a bit of a race condition on iteration 0.  Those two DAQ property nodes are running at the same time.  So when you read the AI.Max, it may be happening before or after the AI.Max is set in your case structure.
    Third, make sure you wire up your error wires.

  • How to change CPU voltage on a laptop?

    I purchased an HP Envy Touch smart 15 for about 1000$ It is using Windows 8.1 a Intel Core i7-4700MQ processor clocked at 2.40Hz, 16.0GB RAM. I have the problem "Your primary display driver has stopped responding and has sucesfully recovered" I have searched for solutions and I have found many sources to say that the soulution was just to change the voltage from 1.00 to 1.05. This makes sense to me as I have tried changing the Timeout delay and deleting/reinstalling drivers, windows updates, switching to windows 7 even. Nothing has worked and the only solution people are getting is this. The only problem is this is a laptop and I checked the bios and found no option for this. Is there a program I can do this with? Thank you for taking the time to read this and please help! It happens often and it is making my schoolwork/homework a living heck.  :/

    Hi,
    No, you won't be able to "overclock" this kind of laptops. One main understanding reason: Laptops will overheat very quick and their lives will be very short. Vendors don't want users send their machines back because of overheated during warranty period.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • P6N-SLI PLATNUM, Memory voltage non adjustable ?

    MS-7350 ver 1.0  bios ver 1.6   memory voltage cannot be changed from auto to manual for voltage adjustment. is there something i need to do to unlock this ?  memory timings are adjustable.

    thanks for the quick responce, i will try that. all of the other settings are changed by first pressing enter first. also the memory voltage is not in bold white letters like the other settings, which led me to believe it is locked out.

  • Software to change USB voltage on Gigabyte motherboard

    Hi, all!
    I need a program/driver which could change USB voltage on the fly. I need that due to iPad 2 which says "Not charging" when I connect it to my PC. I googled and find out that iPad requires higher current in USB port than most motherboards provide.
    In this thread a tool for ASUS motherboards was offered but it's for Windows only. The fact that such a tool exists makes me thinking that it could be implemented for Linux too.
    Thanks.

    Never mind, it's ok.
    Actually, I accidentally told you wrong information. When I decided to find out exact motherboard model, I realized my motherboard is ASUS P5PL2. Sorry, I had to check that far before starting the thread.
    However, I have kind of good news. Here (http://ubuntuforums.org/showthread.php?t=1504845) someone solved the problem on Ubuntu 10.10 x64 and offered a small program which enables iPad charging on PC. For those who might read this thread later I provide direct links to it:
    Page with the program
    Direct link to zipped deb file
    Direct link to source code
    Unfortunately, when I connect my iPad and start the program, it says:
    [bz@bolt ipad_charge]$ sudo ./ipad_charge
    ipad_charge: no such device or an error occured
    I'm not sure, but I guess this might be related to the problem I mentioned two days ago.

  • Strange problems with memory dimms(Banks) in imac 27in mid2010

    Hello dear Apple community. I had a really strange problem with memory dimms(modules anyway)
    I have one really good imac 27in with i7 but as you know after some years the lcd screen became yellowish and cloudy
    So i decided to clean it as i have some knowledge and i did that to others lcd screens with success.
    OK so after successfully cleaning and working like new ( i mean not the external screen with magnets but the lcd internally)i started it.
    Before dismantling my memory was 16gb ( 4x4 dimms)
    After starting it a strange problem arise without any reason! Memory reduced TO 8 GB!!!! memory banks on the right as we seeing it didnt worked at all
    and it was not from dimms because i swapped them..!!!
    So after a lot of thinking and asking tech guys to take a second opinion all the saying (including me that logic board failed for some strange reason.
    Some days before i installed CCleaner and also Onyx because after a lot of installations and uninstallations my mac became a little sluggish..
    I thought that some serious preferences files removed or some hardware settings deleted with Onyx ( is very good and powerful program that can fix the pc and also destroy it in a second) so i removed and reset all preferences. But nothing changed.. So i put a new hard drive and reinstall OXS to see if something can change.
    After formating HD to appleHFS+ saw system profiler that still couldn't see all banks(16gb). I remove logic board and i put another processor i7 that i have as a back up and still nothing( some saying that only these 2 things must be faulty if memory banks not working , processor an logic board and sometimes reinsatlling OS can fix it as i mentioned before. But still nothing...
    So from my nerves and after so much testings and no sleeping for 2 days as it was working i pulled off the memory modules from the right bank i put them again ( off course nothing changed) and i close it. After i restarted it like a miracle finally i saw that i have again 16gb in system profiler!!
    Tech guys here please give me an explanation to this because i gooing crazy! What happened and after i pulled off the dimms while it was working the problem fixed?? It is not recomended at all this action. I forgot to mention that i did Apple hardware test and nothing found..
    Sorry for long post.

    Okay great news...  My memory problems are solved and my Mac Mini is now running at 8 gigs of Ram. I tried the suggested DD3 1333 which  the computer wouldn't even recognize.
    So after visiting the Apple Store in the Fair Oaks VA shopping mall; they suggested that I try DDR3 8500 ram.    I visited Micro Center in Vienna VA, and I purchased BGreg's Suggested Crucial Brand Ram.  10 minutes after I got home the Mac Mini booted on the 1st try with 8 gigs of Ram.
    Some venting that Apple hopefully will read and mention to their resellers....
    The people in the Apple section of MicroCenter in Vienna at first argued that the Mac Mini only supports 4 gigs. EVEN AFTER I SHOWED THEM THE SPECS on the Apple website.  The clerk (who I am calling a clerk because by no means was he a "specialist") even suggested that the Apple site was wrong.  On a later visit to MicroCenter to purchase the DDR3 8500, that the people at Apple recomended; Microcenter even suggested and argued that I needed DDR3 1333 and NOT DD3 8500.  THIS WAS AFTER I TOLD THEM THAT Mac Mini WOULD NOT RECOGNIZE the DD3 1333 Dimms.   Working in retail myself I don't go along with the concept that the customer is always right, however in this instance clearly I was.
    I should point out that some of the staff in Microcenter really do try hard, however like with any business it only takes a few "know it all" bad examples to turn customers off.
    Curious post thought; I wasted about $75 in gas driving to and from Microcenter because of their bad advice. 

  • HT1476 if i bought my ipod touch 32gb in germany where the voltage is 220v and i live in America where the voltage is 110, i will have to wait to get to my home to charge it for first time or I can charge it here and change the voltage of the battery in A

    if i bought my ipod touch 32gb in germany where the voltage is 220v and i live in America where the voltage is 110, i will have to wait to get to my home to charge it for first time or I can charge it here and change the voltage of the battery in America?
    please i need help, im worried that if I connect my ipod here, it will burn or sometihng bad.

    Just connect it to a computer's USB port.
    Most wall chargers are dual voltage (110- 220 volts) and only require a plug adopter. Check the wall charger to see if yours is.

  • Probleme changing the value of a variable in movieclip from my scene

    Hello,
    i have a probleme changing the value of a variable in movieclip from my scene. i explain: I have combobox on my scene containing categories, and in the scene i load an xml file containing links to php files that work with the combobox.
    Also on the scene i have a movieclip "filmstrip", inside this movieclip on the first frame i have a script loading the php file selected in the scene . i use a load() function with a variable "theUrl" inside like this : T.load(theUrl);.
    In my scene i want to change the value of "theUrl" inside the movieClip filmstrip. I tried filmstrip.theUrl = url; But it doesnt work
    the xml file
    <?xml version="1.0" encoding="ISO-8859-1"?>
    <slideshow>
    <area title1="10 Last updated" link1="link1.php"/>
    <area title1="special" link1="link2.php"/>
    </slideshow>
    here is the code on my scene:
    var link1:Array = new Array();
    var LINK:String;
    var url:String;
    var whoOn:Number;
    whoOn=0;
    var x:XML = new XML();
    x.ignoreWhite = true;
    x.onLoad = function(success) {
    var photos:Array = this.firstChild.childNodes;
    for (i=0; i<photos.length; i++) {
    _root.link1.push(photos[i].attributes.link1);
    url=link1[whoOn];
    filmstrip.theUrl=url;//<<--HERE
    x.load("category.xml");
    var cbListener:Object = new Object();
    cbListener.change = function(event_obj:Object) {
    trace(select.selectedItem.label);
    if (select.selectedItem.label == "Last updated") {
    whoOn=0;
    } else if (select.selectedItem.label == "Special") {
    whoOn=1;
    url=link1[whoOn];
    filmstrip.theUrl=url; //<<-----HERE  
    select.addEventListener("change",cbListener);
    here is the code inside the movie clip "filmstrip"
    var T:XML = new XML();
    T.ignoreWhite = true;
    T.onLoad = function(xml) {
    etc etc etc }
    T.load(theUrl);    //<<---HERE it still undefined

    YESSSS . Thanks you very much Kglad it wotk i put all in a function inside the filmstrip function Tload(theUrl){etc ect}and in the root i call it like this filmstrip.Tload(theUrl);   and it works
    code in the root var link1:Array = new Array();
    var LINK:String;
    var url:String;
    var whoOn:Number;
    whoOn=0;
    var x:XML = new XML();
    x.ignoreWhite = true;
    x.onLoad = function(success) {
    var photos:Array = this.firstChild.childNodes;
    for (i=0; i<photos.length; i++) {
    _root.link1.push(photos[i].attributes.link1);
    url=link1[whoOn];
    theUrl=url;
    filmstrip.Tload(theUrl);//<<--HERE
    x.load("category.xml");
    var cbListener:Object = new Object();
    cbListener.change = function(event_obj:Object) {
    trace(select.selectedItem.label);
    if (select.selectedItem.label == "Last updated") {
    whoOn=0;
    } else if (select.selectedItem.label == "Special") {
    whoOn=1;
    url=link1[whoOn];
    theUrl=url;
    filmstrip.Tload(theUrl);//<<-----HERE
    select.addEventListener("change",cbListener);

  • Problem with CPU Voltage

    Hello
    I build new PC with:
    i5-760
    Noctua NH-D14
    MSI P55-GD65
    G.Skill 2x2GB CL7 ECO
    Antec TruePower New 750W TP-750
    TwinTech GF 9600GT
    I have problem with CPU voltage as even when I set it for example to 1.201v in bios, under load it overshot to 1.256-1268. The best is when I oc`ed cpu to 4GHZ and set voltage in bios for 1.30v it overshot for 1.45v+! Not to mention that temps are skyhigh from that. It doesn`t matter if I try to put BIOS Vcore on 1.1v on stock because under load it still rise to 1.16. I turned off all eist, c-state, turbo boost, phase led and switch phase, set vdrop to low and still something is wrong here. I updated the bios under dos from USB stick to newest 1.9 version in order to update CPU micro code without error and it not helped. I want to know is that even possible to fix or should I RMA MB or CPU.
    Minor problem is with sysfans as they power on for a second and turn off instantly to start working again when I see list on devices in post. After rebot when my monitor is switched off it takes something like 5 sec to power monitor on and another 5 to show bios, is that normal?

    I have similar issues, it's hard to tell which measurement is the most accurate, there are 2 different measurements in the control center that don't match up with the figures set in the bios.  The only way to be sure would be to get an expensive accurate multimeter but If you're only interested in running a stable overclocked computer without knowing the exact figures then get the computer running stable and lower the voltages until it starts to become unstable with prime95,
    Or you could work the other way round, set the voltages so it boots but doesn't run prime95 for long, then raise the vcore and vtt one at a time until your happy with the length of time prime95 runs without errors.  I'd be happy with 24 hours, I seem to remember errors creeping in at around the 9 hour mark on the setting below what I have it set to now.

  • Problems with Memory on upgrading

    Problems with Memory. I Dide not hace space to upgrade. Now i do, but It still cancels for lack of space

    Actually, your problem does not sound like memory, but hard drive space. By default, you lose 10% of your drive to the OS and formatting. To tell how much hard drive space you have go to:
    >Finder
    >At the bottom of finder in the gray bar it will tell you how much space you have available on your hard drive.
    Your hard drive should be no more than 85% full! If it is, delete, get a larger hard drive, remove items to an external drive.
    GarageBand only needs 1.2 MB of space.
    In order to use GarageBand, some additional content is required. If you do not already have the content installed, it must be downloaded.
    Make more disk space available by moving some of your files to a different disk (such as an external hard disk or a USB flash drive), or by deleting files you don't need and then emptying the Trash

  • MSI K9N2GM-FD unable to set memory voltage.

    I just bought a MSI K9N2GM-FD and i'm trying to set the memory voltage but the setting remains at [Auto] and grayed out. No key seems to adjust it, is this feature disabled on this board?

    Use +/- keys by the number pad.

  • In iTunes I'm having problems changing the "Media Kind" with a number of playlists in the OPTIONS menu from "music" to "audiobook". After going through the steps, the next time I check the items have reverted back to "music". What step am I missing?

    In iTunes I'm having problems changing the "Media Kind" in the OPTIONS menu from "Music" to "Audiobook". After going through the steps, the next time I check, the items have reverted back to "Music". What must I do to save it as an "Audiobook"?

    After more digging in the Support section here and some Google work, I turned off iTunes Match and lo and behold!  I can change the media kind to Audiobook!  So, it looks like iTunes Match locked the files up somehow and for some reason.
    I went into iTunes Store > iTunes Match > "No, Thanks" to disable it on the local PC.

  • Having problems changing my verizon prepaid to a new device

    I'm having problems changing my Verizon prepaid phone number to a new device.

        Anita65,
    Oh no, sorry to hear you are having so many issues changing your device. However, get some assistance changing your device by contacting Prepaid Support at 888-294-6804.
    KarenC_VZW
    Follow us on Twitter @VZWSupport

Maybe you are looking for