Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanks

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

Similar Messages

CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red, what is this? it isn't in the manual

CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??

No cisco web is working perfectly.
do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
Autonomous AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
LAP AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
Regards

Problem reseting Cisco AIR- LAP1131AG

Dear Expert,
we have customer which used Cisco Air-LAP1131AG and Wireless Lan Controller. The Controller went back to Cisco as Traid in, but we got some AP for our lab.
Problem is, that when you connect via Console cable it brings you into normal mode >, but when going into enable mode it asks for Password. Problem is, that customer changed password and don´t know anymore.
Is it possible to reset the password and configure the AP fresh from beginning?
Thanks
Klaus

and another one with 21 seconds
Press RETURN to get started!
*Mar 1 00:00:06.295: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:06.302: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
*Mar 1 00:00:07.236: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.236: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:20.136: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0 (not full duplex), with ROUTER_VOICE_LAB FastEthernet0/0 (full duplex).
*Mar 1 00:00:25.331: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:34.342: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 192.168.200.183, mask 255.255.255.0, hostname 24
24>
24>
24>ðXmodem file system is available.
flashfs[0]: 26 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7131136
flashfs[0]: Bytes available: 8867840
flashfs[0]: flashfs fsck took 32 seconds.
Base ethernet MAC Address: 00:1d:a1:ee:97:b4
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 10 mbps, half-duplex
Ethernet port 0 initialized: link is up
button pressed for 21 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
examining image...
%Error opening (connection timed out)Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
Image text-base: 0x00003000, data-base: 0x0035E440
Initializing flashfs...
flashfs[1]: 26 files, 9 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 7131136
flashfs[1]: Bytes available: 8867840
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1147Q1KT
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:A1:EE:97:B4
Part Number                          : 73-8962-12
PCA Assembly Number                  : 800-24818-11
PCA Revision Number                  : B0
PCB Serial Number                    : FOC11443WRR
Top Assembly Part Number             : 800-29144-02
Top Assembly Serial Number           : FCZ1147Q1KT
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-E-K9
% Hostname contains one or more illegal characters.
Press RETURN to get started!
*Mar 1 00:00:06.294: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:06.302: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
*Mar 1 00:00:07.236: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.236: %LINEPROTO-5-UP
24>
24>DOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:09.820: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
24>
24>en
Password:

MDS 9216 - showing red status LED, not starting up

Hi,
In a recent power loss (took out our R&D UPS in the process), an MDS 9216 we have in R&D failed.
On power up, it shows a red status LED, and does nothing. We've pulled and swapped PSUs (something we're told is a common fix for a common problem with these chassis), to no avail.
Strangely, we pulled the fan card (which had a green light), and put it back in to see it now also has a red status light.
We've swapped all cards around for new and spares (even the main cards) and they show up with red status lights in the chassis (can't test them in another chassis at present) so I assume this problem is with the chassis itself (ie the backplane or PSUs).
Any ideas, any similar experiences?
Many thanks,

As far as warranty, it would be covered for 1 year or 90 days from purchase....not sure which, but since the 9216 is end of sale for a few years now, I doubt that is covered under warranty. If you have a maintenance contract covering that 9216 serial number, then it would be covered. The design on the 9216 is that the module 1 is not field replaceable. There is no Cisco part number for the slot1 line card. It is a hybrid of a 16 port FC module with a supervisor daughter card. It is basically considered part of the chassis. If you have your own spare 9216 and feel energetic you could replace the slot 1 line card....but from the official support perspective, it is not replaceable.
There are no other replaceable parts besides the chassis and PS that would cause this problem. (I assume you have removed any line card from slot2 to be sure it was not causing the problem).
Thanks,
Mike

Cisco 1131AG LWAP status led yellow and other leds blinking green

I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
The SSID broadcast is enabled.
On the switch the interface is up and there is traffic going in and out of the LAP.
I tired power reset and factory reset for the APs but the problem remains the same.
Any ideas for what might be the problem ?!!
Regards

Yes the clients are not able to see the SSID broadcasted by the AP.
But these APs were functioning normally before without any changes to the WLC config.
I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

Cisco 4402 LAP1131 Interference Profile Failed for Base Radio MAC:

Dropped connections every day, few times a day.
WLC Was working perfectly fine for about a year then had some dropped connections.
Upgraded to the latest firmaware and also default it to the factory and reconfigured it.
Same problem!
Cisco 4402
Software Version 7.0.98.0
8x Cisco: AIR-LAP1131AG-A-K9 also v/7.0.98.0
Interference Profile Failed for Base Radio MAC:

This is a threshold parameter: "Interference Profile failed" along with some others. All this does is send alerts to the WLC log, to your syslog or to your WCS/NCS or Prime Infrastructure management tool. You need to adjust these for your environment if you see too many alerts being triggered. Interference can be a main issue in downtown big citites and you would bump the value up to reduce the number of alerts you see. Yes interference will cause issues, but this is an alert threshold and will not fix your interference, just tell you that you have interference due to hitting the X value.
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"*****

1131AG no status LED

Hello,
One of my 1131AG access points stopped working and I am trying to troubleshoot.
When I apply power (originally it was PoE) the Status LED never does anything (not even a blip), the Ethernet and Radio leds will flash, but the status LED will never light.
Any thoughts?
Thanks
Rob

Rob,
     Is this an IOS or LWAPP access point your troubleshooting, the reason I ask is because it's possible to disable that Circular status LED from within the software and it's possible it has gotten disabled.
     If it is an LWAPP access point, I'd just do a factory reset on the unit and then see if it comes back up or console into it first and see if it is even booting.
     if it is an IOS access point console into the unit and enter enable mode by typing en; then enter config mode (conf t), from there you should have an command that is something like status led and the options are enable, disable, blink
Hope this helps... Please rate useful posts.
Thanks,

How to read the power and status LEDs on cFP2020

Can the cFP2020 Power and Status LEDs be monitored by a host program? Also, can the Power and Ready LEDs be monitored from the other cFP Modules?

You can not directly read the Network Module Power or Status LED from a host program. Likewise, you can not directly read the Power and Ready LED of an IO module.
However, even though you can not directly ready the LED status, there are ways of finding out most of the information that the LEDs convey.
For the Network Module Power LED, you can infer the status of the Power LED by looking at the channel status for any/all items that are on the bank. If the items have errors indicating that a communication timeout has occured or an addressed item does not exist, then it is probable that the unit is offline (either because of no power or a fault). The Status LED indicates the current operating status of the Network module and in most cases, if it is flashing
, then a fault has occured that shutdown the processor. In most cases, you will not be able to determine that the Status LED is flashing, as the Status LED indicates a fault condition which will put the unit into a non-standard operating mode (e.g. firmware corruption, unassigned IP Address, or an OS fault).
For the IO modules, each channel on a module can report status, and based upon the status you can infer the state of the LEDs. If the module does not have the Power LED lit, the most likely status will be "Addressed item does not exist". If the module has the Power LED but no Ready LED, then the status will indicate that the "item is unconfigured". If the module has both a Power and Ready LED, than the channel should report either a good status, or a channel specific error (if applicable).
Regards,
Aaron

How can I disable the wireless status LED (T61)?

When I'm working on my laptop and listening to, for example, online radio the wireless status led under the screen keeps blinking (data is being transmitted). I find this extremely annoying and distracting. Is there any way to disable the LED? (but obviously I would still need to be connected). I'm using windows xp on a thinkpad T61.
Help much appreciated!

i would use a black permanent marker or something, or a black sticker. This is the easiest and safest way of doing it, it is perfectly reversable.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Cisco AIR-LAP 1522 PROBLEM

Hello to everyone. They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 18 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 15537664
flashfs[0]: Bytes available: 16331264
flashfs[0]: flashfs fsck took 23 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 00:27:0c:27:3f:00
Low Power PoE - enabling LAN Ethernet port only
Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################
File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 18 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31352832
flashfs[1]: Bytes used: 15537664
flashfs[1]: Bytes available: 15815168
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio0 present A600 8000 A8020000 0 A8030000 30
Radio1 present A600 8000 B8020000 0 B8030000 13
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
%Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9   (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
Processor board ID FCW1346W00Q
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power loss
LWAPP image version 6.0.199.0
4 Gigabit Ethernet interfaces
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:27:0C:27:3F:00
Part Number                          : 73-10918-04
PCA Assembly Number                  : 800-28909-04
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13430YBS
Top Assembly Part Number             : 800-29338-04
Top Assembly Serial Number           : FCW1346W00Q
Top Revision Number                  : F0
Product/Model Number                 : AIR-LAP1522AG-E-K9
% Please define a domain-name first.
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
Press RETURN to get started!
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)
*Mar 1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Mar 1 00:00:10.695: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
*Mar 1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start
*Mar 1 00:00:10.759: Warning: Failed to run startup script
*Mar 1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
*Mar 1 00:00:25.771: No Mesh startup file found
*Mar 1 00:00:29.763: Logging LWAPP message to 0.0.0.0.
*Mar 1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)
*Mar 1 00:00:45.355: -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).
*Mar 1 00:00:45.355: -If a power-injector is installed, issue the command:"power inline negotiation injector installed"
*Mar 1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.
*Mar 1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora
*Mar 1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ
*Mar 1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link Down

Search this doc for "reset"
http://www.cisco.com/en/US/docs/wireless/technology/mesh/design/guide/MeshAP_52.html
Reset Button
The access point has a reset button located on the bottom of the unit (see Figure 3). The reset button is recessed in a small hole that is sealed with a screw and a rubber gasket. The reset button is used to perform these functions:
•Reset the access point—press the reset button for less than 10 seconds. LEDs turn off during the reset and then reactivate when the reset is complete.
•Disable battery backup power—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
–You can also disable the battery remotely by entering this command:
config mesh battery-state disable AP_name
•Switch off LEDS—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
Figure 3 Reset Button Location
1
Reset button location
Sent from Cisco Technical Support iPhone App

Cisco AIR-AP1242AG-A-K9 Vs AIR-LAP1131AG-N-K9 Which AP is best

Dear All,
I am confused between AIR-AP1242AG-A-K9 and AIR-LAP1131AG-N-K9, we have WLC 4400 which supports both, which one will be the best.
and what are the adv. adn disadv. of both.
Thanks,
Almas...

Almas,
Depends on what you are looking to do. Both are good for any standard deployment, i.e. office space, hallways.
The 1242 is a bit more flexible as it has external antenna that can be articulated. So you can mount it on a wall, or on the ceiling. The down side, is they will be visible.
The 1131 has built-in antenna, and is designed to be mounted horizontally, on a ceiling for example.
So depending on where you can mount, that will determine the type of AP you need to use

Cisco AIR-CAP26021-A-K9 || Error opening tftp:// ... /ap3g2-k9w7-tar.default

Hi everyone:
I have a problem with two Cisco AIR AP's ... I have configured already eight of them (in lightweight mode), but those two send me the next error, right now.
ap: %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)
And when I boot to the AP, it says:
%Error opening flash
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 11 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 15 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: c0:67:af:6f:31:25
Ethernet speed is 100 Mb - FULL Duplex
button is pressed, wait for button to be released...
button pressed for 21 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g2-k9w7-tar.default
examining image...
DPAA Set for Independent Mode
DPAA_INIT = 0x0
%Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)ap:
ap:
ap:
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 14 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: c0:67:af:6f:31:25
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...###########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 7 seconds.
Base Ethernet MAC address: c0:67:af:6f:31:25
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
executing...
Initializing flashfs...
flashfs[2]: 10 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31739904
flashfs[2]: Bytes used: 7245824
flashfs[2]: Bytes available: 24494080
flashfs[2]: flashfs fsck took 8 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete.
Copying radio files from flash: to ram:
%Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
Uncompressing radio files...
File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
...done Initializing flashfs.
Press RETURN to get started!
*Mar 1 00:00:11.335: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:13.071: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.663: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:08 by prod_rel_team
*Mar 1 00:00:13.795: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:13.795: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Mar 1 00:00:13.799: %PARSER-4-BADCFG: Unexpected end of configuration file.
lwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:14.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:16.467: DPAA Initialization Complete
*Mar 1 00:00:16.467: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:16.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:47.151: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inline power source
*Mar 1 00:00:49.515: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.44.221, mask 255.255.255.0, hostname APc067.af6f.3125
Translating "CISCO-CAPWAP-CONTROLLER.asf.gob.mx"...domain server (10.1.1.2)
*Mar 1 00:01:00.403: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:00.451: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.asf.gob.mx
The thing is, I've been applying the instruction:
capwap ap controller ip address 10.4.13.2
'cause I want them to communicate with a remote controller, and the past eight did it fine, but this two didn't.
As for the things I've already tried, I have reset it's parameters to it's initial settings, I've tried to load a new IOS image, I've cleared the flash memory, but nothing works, it keeps communicating with the old controller.
How can I fix this? (I mean, changing or adapting the AP to a lightweight AP)
Thanks in advance

Its fine to try to apply it from the console...but if you really want to clear the AP, you need to clear the nvram. so if changing the primary from the GUI that the AP has joined didn't work, then try this:
debug capwap console cli
erase /all nvram
Example:
Entered the username and password
debug capwap console cli
erase /all nvram:
[confirm]
undebug all
reload
[confirm]
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Problem Joining AIR-CAP1602I-C-K9 with WLC 5508

Hi,
I am having trouble to get AIR CAP1602I-C-K9 attached to a 5508 WLC running code 7.4.110.0
Here is what I got from the AP logs:
====================================================================================================
Extracting files...
ap1g2-k9w8-mx.152-2.JB2/ (directory) 0 (bytes)
extracting ap1g2-k9w8-mx.152-2.JB2/K5.bin (75790 bytes)!!!!
*Dec 6 15:09:23.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 6 15:09:23.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.10.100 peer_port: 5246
*Dec 6 15:09:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.10.100
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: CAPWAP!
extracting ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2 (9202946 bytes)!!!!!!!!! SM handler: Failed to process message type 10 state 5.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.16.10.100perform archive download capwap:/ap1g2 tar file
*Dec 6 15:09:23.583: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Dec 6 15:09:23.587: Loading file /ap1g2...
*Dec 6 15:09:24.007: %LINEPROTO-5-UPDOWN:!!!!!!!!!!! Line protocol on Interface Dot11Radio0, changed state to down
*Dec 6 15:09:24.063: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!!
*Dec 6 15:09:25.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!
*Dec 6 15:09:26.135: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Premature end of tar file
ERROR: Problem extracting files from archive.
Download image failed, notify controller!!! From:7.4.1.37 to 7.4.110.0, FailureCode:3
archive download: takes 63 seconds
*Dec 6 15:10:26.851: capwap_image_proc: problem extracting tar file
====================================================================================
after that the AP reboots and do same process over and over again,
Please help..
Many Thanks,
Barth

Here is the info about AP and WLC:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... WLC1-AP
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 172.16.10.100
Last Reset....................................... Power on reset
System Up Time................................... 0 days 4 hrs 12 mins 28 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +44 C
External Temperature............................. +28 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ F8:72:EA:EF:2E:A0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, Power Off, Fan On
Maximum number of APs supported.................. 100
AP4403.a7fd.f040#sh ver
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:45 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP4403.a7fd.f040 uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-2.JB/ap1g2-k9w8-mx.152-2.JB"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-C-K9    (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
Processor board ID FGL1711ZJNW
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:03:A7:FD:F0:40
Part Number                          : 73-14671-04
PCA Assembly Number                  : 000-00000-00
PCA Revision Number                  :
PCB Serial Number                    : FOC16517DZ1
Top Assembly Part Number             : 800-38552-01
Top Assembly Serial Number           : FGL1711ZJNW
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP1602I-C-K9
Configuration register is 0xF
AP4403.a7fd.f040#sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-C-K9 , VID: V01, SN: FGL1711ZJNW

Radio interface Problem in Air-lap1131-a-k9

I have one Air-lap1131-a-k9 and i convert in autonomus system , but when the AP reload the message " the interface radio is not present " apper
so when i type sh run the interfaces radio dont apper...
Please help me

Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(21a)JY, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 28-Apr-10 10:40 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 150 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 10304512
flashfs[1]: Bytes available: 5694464
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio0 not present 0 0 0 0 0 3
Radio1 not present 0 0 0 0 0 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-LAP1131AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FTX1253N1KJ
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:23:04:B7:BA:8C
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC125002LQ
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FTX1253N1KJ
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-A-K9
Press RETURN to get started!
*Mar 1 00:00:06.194: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 28-Apr-10 10:40 by prod_rel_team
*Mar 1 00:00:54.649: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:00:55.601: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
ap>
ap>
ap>en
Password:
*Mar 1 00:01:06.553: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:01:07.553: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
Password:
ap#sh run
Building configuration...
Current configuration : 731 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$yzUD$BN8tHBfXumwWzTMN9YDj20
no aaa new-model
dot11 syslog
username Cisco password 7 1531021F0725
bridge irb
--More--                           !
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
--More--                           line vty 0 4
login local
end
ap#
ap#sh      hardware
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(21a)JY, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 28-Apr-10 10:40 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (
fc2)
ap uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w7-mx.124-21a.JY/c1130-k9w7-mx.124-21a.JY"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-LAP1131AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/81
92K bytes of memory.
Processor board ID FTX1253N1KJ
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:23:04:B7:BA:8C
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC125002LQ
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FTX1253N1KJ
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-A-K9
Configuration register is 0xF
ap#         sh un
ap#         sh inv
ap#         sh inventory
NAME: "AP1130", DESCR: "Cisco Aironet 1130 Series (IEEE 802.11a/g) Access Point"
PID: AIR-LAP1131AG-A-K9, VID: V05, SN: FTX1253N1KJ

Cant Connect Cisco AIR-CAP 3602 with 2504 controller

Im trying to have one of our APs join our controller. No matter what I do, i cant get it to join the controller.
The controller has the right OS, I had to upgraded it 7.4 to support the 3600...
Both the controller and the AP has the same time and date.
But Im getting this from my AP:
*Oct 30 14:49:26.043: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Oct 30 14:49:26.067: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 30 14:49:26.083: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 30 14:49:27.055: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 30 14:49:27.095: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Oct 30 14:49:27.103: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Oct 30 14:49:28.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 30 14:49:28.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Oct 30 14:49:28.131: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 30 14:49:28.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 30 14:49:28.147: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 30 14:49:29.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Oct 30 14:49:29.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 30 14:49:29.167: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 30 14:49:30.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 30 14:49:36.083: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 30 14:49:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
*Oct 30 14:49:36.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
*Oct 30 14:49:36.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
*Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
Anyone can help me please?
Thanks....

AP is connected directly to one of the ports on the 2504 controller.
I can move it to a POE switch, if needed.
Here is the output after I boot up the AP:
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Macronix Mirrorbit (00C2)
Xmodem file system is available.
flashfs[0]: 43 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 16767488
flashfs[0]: Bytes available: 15230464
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 4c:00:82:77:32:7b
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1"...###########################
File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 43 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 16767488
flashfs[0]: Bytes available: 15230464
flashfs[0]: flashfs fsck took 8 seconds.
Base Ethernet MAC address: 4c:00:82:77:32:7b
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1;flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1'
Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1"...###############################
File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 22:57 by prod_rel_team
Initializing flashfs...
flashfs[3]: 43 files, 9 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31739904
flashfs[3]: Bytes used: 16767488
flashfs[3]: Bytes available: 14972416
flashfs[3]: flashfs fsck took 8 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 244 entries (64 SGI/104 BF variants)
Radio1 present 8764 8000 0 88000000 88010000 4
Radio2 not present 0 0 0 0 0 8
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FTX1731GQYY
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.5.102.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 4C:00:82:77:32:7B
Part Number                          : 73-14521-02
PCA Assembly Number                  : 800-37501-02
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17273HG4
Top Assembly Part Number             : 800-35852-02
Top Assembly Serial Number           : FTX1731GQYY
Top Revision Number                  : C0
Product/Model Number                 : AIR-CAP3602I-A-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:11.355: FIPS IOS test Image Checksum successful
*Mar 1 00:00:11.355: FIPS IOS test Crypto RNG DEK Key Test successful
*Mar 1 00:00:11.355: FIPS IOS test SHA-1 successful
*Mar 1 00:00:11.355: FIPS IOS test HMAC-SHA1 successful
*Mar 1 00:00:11.355: FIPS IOS test AES CBC 128-bit Encrypt successful
*Mar 1 00:00:11.355: FIPS IOS test AES CBC 128-bit Decrypt successful
*Mar 1 00:00:11.355: FIPS IOS test IOS AES CMAC Encrypt successful
*Mar 1 00:00:11.355: FIPS IOS test IOS CCM Encrypt successful
*Mar 1 00:00:11.355: FIPS IOS test IOS CCM Decrypt successful
*Mar 1 00:00:11.387: FIPS IOS test RSA Signature Generation successful
*Mar 1 00:00:11.391: FIPS IOS test RSA Signature Verification successful
*Mar 1 00:00:11.391: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:11.391: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:11.847: Registering HW DTLS
*Mar 1 00:00:14.647: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:18.327: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
*Mar 1 00:00:18.327: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.327: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.327: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.327: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:24.451: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
*Mar 1 00:00:24.451: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.451: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.451: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.451: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:26.811: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 22:57 by prod_rel_team
*Mar 1 00:00:26.811: %SNMP-5-COLDSTART: SNMP agent on host AP4c00.8277.327b is undergoing a cold start
*Jul 4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jul 4 23:55:50.051: %PARSER-4-BADCFG: Unexpected end of configuration file.
lwapp_crypto_init: MIC Present and Parsed Successfully
*Jul 4 23:55:50.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Jul 4 23:55:50.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Jul 4 23:55:51.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Jul 4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jul 4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jul 4 23:55:53.319: FIPS HW test SHA-1 successful
*Jul 4 23:55:53.319: FIPS HW test HMAC-SHA1 successful
*Jul 4 23:55:53.319: FIPS HW test AES CBC 128-bit Encrypt successful
*Jul 4 23:55:53.319: FIPS HW test AES CBC 128-bit Decrypt successful
*Jul 4 23:55:53.819: FIPS HW test SHA-1 successful
*Jul 4 23:55:53.819: FIPS HW test HMAC-SHA1 successful
*Jul 4 23:55:53.819: FIPS HW test AES CBC 128-bit Encrypt successful
*Jul 4 23:55:53.819: FIPS HW test AES CBC 128-bit Decrypt successful
*Jul 4 23:55:53.819: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
*Jul 4 23:55:53.819: DPAA Initialization Complete
*Jul 4 23:55:53.819: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Jul 4 23:55:54.819: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
*Jul 4 23:56:13.191: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Jul 4 23:56:14.279: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jul 4 23:56:15.279: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jul 4 23:56:15.371: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jul 4 23:56:16.371: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jul 4 23:56:18.895: Logging LWAPP message to 255.255.255.255.
*Jul 4 23:56:23.627: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.1.150, mask 255.255.240.0, hostname AP4c00.8277.327b
Translating "CISCO-CAPWAP-CONTROLLER.pti.local"...domain server (10.3.1.32)
*Jul 4 23:56:34.559: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Jul 4 23:56:34.567: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.pti.local
*Jul 4 23:56:44.567: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 30 15:05:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
*Oct 30 15:05:13.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
*Oct 30 15:05:13.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
*Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
*Oct 30 15:05:18.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50

Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

Similar Messages

Maybe you are looking for