Problem connecting to the server Timecapsule

I am working with a Motora Surfboard SBG6580 Cable Modem going to my 4th Gen Airport Extreme, then a wireless bridge to my 3rd Gen 2 Gig TimeCapsule to extend the network, then using ethernet cables to TV, DVD and MacMini. When trying to run a backup with Time Machine, or just using it as a hardrive, I keep getting the error message "There was a problem connecting to the server "Timecapsule" - The server may not exist or is unavalable at this time. Check the server name or IP address, check your network connection, and then try again." I have seen a lot of posts on this problem, but I still don't understand what the issue or resolution is.
I have tried resetting the TimeCapsule, connecting the TimeCapuse with an ethernet cable, turning off wireless functions, wiped the drive and zero'd all data, etc., but with the same results. I may be wrong, but this all seems to have started when I ran MATCH while using the TimeCapsule as a storage device for all my iTunes media - it corrupted all my data and showed my disk as full, though pretty much everything on the disk was missing. All was working fine until that point.
Any help would be nice. Help!!
Thanks in advance

If you have backed up to 77GB or something then a backup has indeed been made.. On the TC there will be a sparse bundle and backup which can be mounted.. You cannot check the disk.. you check the sparse bundle.. which can be mounted.
Please do the following.
Disconnect and remove the TC from the network.
Plug it directly into the computer by ethernet. No other connection to the TC.. turn off wireless and every other connection to the computer..
If you still have issues.. press reset and redo the setup of the TC again.
Run Time Machine and see if it works. If it doesn't work now you have serious issues.. I would guess at a faulty disk somewhere.
What OS is on the computer? From the first post you use SL still.
I would also take the firmware of the TC back to 7.5.2 as I mentioned and do full factory reset this time.. ie hold in reset and then power on.. continue holding in reset until led flashes rapidly.

Similar Messages

HT2284 Recurring "connection failed" when selecting TimeCapsule in the sidebar (internet connection works fine). Clicking "Connect As" starts the cyle over again but ends in "There was a problem connection to the server" message. Only fix is resetting T

Recurring "connection failed" when selecting TimeCapsule in the sidebar (internet connection works fine). Clicking "Connect As" starts the cyle over again but ends in "There was a problem connection to the server" message. Only fix is resetting TC.
The TC is the wifi base station, also have AirportExpress on the network, both of which work fine. The TC has an external disc connected as well, which is also visible in the sidebar but also cannot be connected to. Several MB computers use the network, all of which either can or cannot connect to the TC disc depending on when it is acting up.
Any ideas other than clicking "connect as" or powering down the network every time?

Read up how to install 5.6 utility into ML.. it is pretty easy.
I downloaded 5.6
http://support.apple.com/kb/DL1482
Download unpkg
http://www.timdoug.com/unpkg/
Open the dmg to get the pkg.. drag it onto unpkg.. and it will create a directory under desktop with all the files.. drag the application to the utility directory.. or just run it direct.
Google if you want more explicit instructions.
Much easier with a real tool instead of a toy.
Hold the option key when you select firmware update.. all the old ones will appear.
But this will not work on newer Gen4.. only on every other model and early Gen4. .I do not know when they turned the corner and started this only 7.6 nonsense.

There was a problem connecting to the server "Max Time Capsule"

Disclaimer: Previously posted here (Ask Different) and similar to this.
I'm trying to use my MBP inside and outside my office, and having it backup to my 2TB Time Capsule when on its wireless network, or defer backups when not on the Time Capsule's wireless network.
Unfortunately, if I've been on a different wireless network for a few hours worth of backup attempts, bringing the machine back onto the Time Capsule's wireless network doesn't resume backups, and Time Machine never recovers. I can select the disk as a backup drive in the Time Machine preferences, but the disk remains unavailable from the Finder, and any backup attempts yield the standard:
There was a problem connecting to the server "Max Time Capsule"
Check the server name or IP address, and then try again. If you continue to have problems, contact your system administrator.
My WiFi connection is through the same Time Capsule that hosts the backup drive, and its name and IP address have decidedly not changed. The only thing that seems to help is restarting the Time Capsule, but that is an inconvenient workaround at best.
The problem sounds similar to Backup Disk Not Available, but the answers to that question are either to restart or change the disk name or turn off the 5 GHz network (which didn't help). I also looked at /Library/Preferences/com.apple.TimeCapsule.plist, but found nothing that seemed relevant.
Any suggestions would be greatly appreciated. My MBP is running OS X 10.7.5, and the Time Capsule firmware is 7.6.1.

There was a problem connecting to the server "Airport Time Capsule".
The server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again.
I still have internet connection, and have tried other suggestions across internet but really the only fix has been to power cycle the ATC. This unfortunately is only a temporary remedy for a day or so until it returns.
Any suggestions on how to fix this problem?
There is no fix.. I have written a bunch of suggestions to try.
https://discussions.apple.com/thread/6106750?tstart=0
It is very common on Mavericks.
How long did it take from when you set it up till it went bad??

I'm trying to set up my Ipod, but when I go to sign in with an apple ID it says 'Could not sign in: there was a problem connecting to the server'.

I just bought a 3rd generation ipod touch. It was professionally refurbished. I'm trying to set it up, and everything seems to be working fine, until we get to the wifi. I live on campus and our wifi is username and password protected. I signed in and everything seemed to work fine, and in the top left hand corner I have all the bars for wifi. However, when I go to sign in with an apple ID it says 'Could no sign in: there was a problem connecting to the server'. I've tried turning it on and off again, tried signing on to our wifi again, but it all isn't working. What can I do?

I also encountered the same problem. Try using a different email address or try signing in later.

There was a problem connecting to the server ... OS 10.8.4 + WD NAS

Dear all,
first my configuration:
iMac from mid 2012, MacOS X Mountain Lion, 10.8.4, iPhoto 09 v. 8.1.2 - all software updates done and up-to-date
MacBook Pro late 2011, MacOS X Mountain Lion, 10.8.4
NAS WD My Book World Edition II (white light), 2 x 1TB (configured RAID : 1TB mirrored), original firmware (01.02.14 with MioNet built on Thu Feb 9 14:11:48 CST 2012 ) NFS, AFP enabled
a win 7 laptop and plenty of other devices
everything on a LAN with GB router + WiFi
I have my iPhoto library on my iMac, but the photos (the originals) stored on the NAS. I have the option "copy photos to library when importing" disabled. So I guess iPhoto has a reference / link in the library to the original files.
Everything used to work fine until some weeks ago. Not sure what happened but suddenly I got the error message "There was a problem connecting to the server ... Check the server name or IP address, and then try again. ..." when I tried to import photos stored on my WD NAS. When I want to display any photo stored on the NAS - same thing.
Now I guess I have a bunch of gray hairs more while trying to get this fixed.
I tried so many of the tips posted everywhere including booting in save mode, deleting the .plist files (first I actually tried to clean them using Xcode first before deleting them), etc. I cleared out KeyChain. I removed all recent entries (folders) and recent servers from the "history". I tried to connect as guest or named user. There are also no "logIn items" pointing to the NAS. I even tried to disable / enable AFP + NFS on the NAS, not to mention countless restarts of all the machines
One other thing I noticed: Before that problem occured I was able to select the NAS in Finder and it would show me all the shares. When I selected one of them it was mounted automatically. When I select it now I get "connecting" for a loooong time and then "Connection Failed". Most of the time (not always!) however I am able to get in via "Go -> Connect To Server - smb://<nas server name>). And suddently after that also selecting the NAS in Finder shows me all the shares! Hoever even this not in 100% of all cases. I can replicate this from the iMac and the MacBook.
I do use an external HD for TimeMachine to back up my data (directly connected via USB). No issues there.
Not I really don't know what to do any more
Do you have any ideas? Did anyone ever get a response from Apple with a useful solution that really hit the core of the issue?
Thank you!

SOLVED!! and I want to share the solution which worked for me with everybody here. Ultimately I had to install nettalk 2.2 on my NAS as described here: http://mybookworld.wikidot.com/netatalk2-2-on-whitelight . A nice description on how to do that can be found here: http://forums.macrumors.com/showthread.php?t=1102423 .
One last remark: When asked about the "DHX2 login process", I opted to install the original version, so I can confirm this one works too.

"There was a problem connecting to the server" in iTunes after migrating to new mac

I have a problem that is driving me crazy with my brand new iMac. I see many other people posting similar issues, but none of the other solutions seem to work for me.
I had a MacPro and bought a new iMac, on which I used Migration Assistant to set up. So the new iMac is virtually the same as my old machine in terms of appearance and installed applications. Both machines have Mountain Lion 10.8.2. All software on both machines has been through Software Update and is fully up to date, as are the connected devices (iPhone and iPad).
The problem is with iTunes. Every time I start iTunes (I think at the moment it checks my two connected devices) I get a pop up dialogue saying:
There was a problem connecting to the server "MacPro".
The server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again.
This dialogue continues to pop up constantly as long as iTunes is open, interrupting my work and frustrating me no end. The old machine is of course turned off and indeed is not available -- but I can't find what on the new iMac is so desperate to connect to it.
So far I have tried completing erasing my iTunes library, deleting all the preferences, reinstalling iTunes from a fresh download of the dmg, safe rebooting several times with no peripherals connected at all, and deleteing other preferences like the Login Items, iPhone config and iPhoto. I have also cleared Recent Items from the apple menu and opened "Connect to Server" in the finder and cleared all servers from the dropdown menu.
Last night I also completely restored my iPhone from scratch to see if that would clear away the issue and I have connected both iPhone and iPad to go through any apps that have permission to write content to my computer and deleted all of them completely from the devices.
Nothing has changed at all after all that, and I have run out of ideas. Clearly there is something somewhere that has my old machine's name hard coded in it but I can't see any way to search for it. I would grep my Library folder but I think a lot of the files are binary so I'm not sure that would unearth anything. I've seen many posts saying that Apple phone support (which I would qualify for) can't help with this issue and so I have put off phoning them to simply run through all the things I've already tried.
Any advice that anyone could offer would be extremely helpful. I can't use iTunes at all like this as it disrupts everything I try to do on the new machine.
many thanks!!

Nothing at all? Can't anyone help with this issue at all? I would be grateful for any suggstions as it is driving me crazy. It happens every time I open iTunes and also every time I open Mail.

HT4628 my time capsule has stopped working - have a green light but get an error message saying "there was a problem connecting to the server..."

I noticed this week an exclamation mark on the time machine icon on the menu bar.
My Macbook, iPad and iPhone all connect to the network but i get "there was a problem connecting to the server..."
When I open the preferences the time capsule is off but turnign it back on sends me in a loop of selecting the Time Capsule device (which has a nice green light etc) and then getting the error messgae about being unable to connect. I've pulled the plug a couple of times (this has worked in the past) but no change.
Any advice would be welcome before I try a factory reset or have to return to Apple for repair (the one thing they are offering as the thing is only 5 months old)

I also noticed that when I go to finder I see two MacBook Air's that are in my name but have the number (2) and (3) next to the name.
That is a well known bug in Yosemite.
Try open System Preferences (gear icon on the dock)
Open Sharing
Edit back to the correct name for your Mac
This may...or may not help. But, it won't hurt.
The Mac's name may stay stable....or you may see (2), (3), etc again soon.
Be sure to restart both your Mac and the Time Capsule after you do this.

It says that "there was a problem connecting to the server". What's wrong with this, and how can I deal with this problem?

I just got my new iPad Mini2, and when I choose "sign in with your apple ID", it says that "there was a problem connecting to the server". What's wrong with this, and how can I deal with this problem?

1. Turn router off for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings

I install LION on my mac pro 2008 and it's alway's pop with " there was a problem connecting to the server " Time Capsule" .How can i remove this popup. My Time machine is working fine and also rename it. But the popup keeps on coming with the old name.

I installed LION on my mac pro 2008 and it's alway's pop with " there was a problem connecting to the server " Time Capsule" .How can i remove this popup. My Time machine is working fine and also rename it with less than 7 karakters. But the popup keeps on coming with the old name.

I have a BT Infinity router plugged into the Time Capsule, not sure where the radio settings are?
They are able to use the network settings of the TC i.e. they can connect to the internet via the wifi through the TC but when they try and connect to the AirPort Disk this is where it is not allowing a connection.
I don;t have the drive shared out at all at the moment, is this necessary? How do I do this if so?
I have attached the screen shots of all the settings.
Thanks again for your help.

On submit button type - There was a problem connecting to the server.

Hi,
Please give me a solution for server connection issue. I am new to the adobe live cycle designer ES4.
I created a web form use of adobe live cycle es4 v.11.0 to retrieve the data from web service method. So, I created the WSDL type data connection in data view menu to invoke the .asmx?wsdl service and connection is established successfully. Then, I dragged and drop a button from object library window to invoke the service method and changed the type as submit button. In the submit button URL, I given the web service url as eg. http://<localhost>:<port>/Web_serive.asmx?wsdl. Finally, I saved it has a PDF file.
When I click the submit button, a pop up window is openning as 'preparing for submit..' and 'Receving data..' and finally, it shows a pop up error message as 'An error occured during the submit process. There was a problem connecting to the server'. I tried all possiblities and if any bad english grammer, sorry for that.
Please give me a proper solution for this issue.
With Regards,
G. Prabakaran.

After trying these suggested actions several times success has not been reached.
I understand you are getting unable to connect to server error message on your printer. I would first unplug router and printer for about 1 minute. I would plug router up first then printer. I would then try to enable web services. If not successful and you get same error message. I would follow these steps.
1. Obtain your printer's IP address
a. This can be done by pressing the wireless icon on printer.
2. Enter the printer's IP address in a browser.
3. Select the network tab at the top of the page.
4. On the left select networking.
5. Select Network Address (IP)
6. Select Manual DNS Server
a. Manual Preferred DNS should read 8.8.8.8
b. Alternate DNS Server should read. 8.8.4.4
7. Select apply you might get a warning just select okay.
8. Try again to access ePrint.
Let me know how it goes.
I am able to print wirelessly to the printer, print through eprint, scan, and copy things. The only thing that is not working is the printer itself connecting to the hpeprintcenter.com.
Kyle

Popup window error message on a Mac .....There was a problem connecting to the server 172.17.0.22

I keep getting a popup error message on my mac "There was a problem connecting to the server 172.17.0.22"
How do I fix this problem

That is The moment you go to open a new website it will reappear and then you need to close it before I can access the website I want. …

Error message: a problem connecting to the server "DriveMap"

I recently uninstalled GoDaddy’s software Workspace, used to manage online storage which I no longer need. Every time I restart my computer, and worse, every time I update an app, put something in the trash, or empty the trash, I get the error message “There was a problem connecting to the server "DriveMap". Workspace (DriveMap) is no longer on my computer; I used GoDaddy’s Workspace uninstaller to remove it. Then I reinstalled and uninstalled again because I was getting that message. I then did a search of my computer for all files with “Starfield” in the title, which is the developer of WorkSpace. I found about a dozen files and deleted them. I’m still getting the message, and GoDaddy support is absolutely useless. I got this reply from them (their 15th reply about this problem).
It appears that your computer is configured to open a drive, which is occurring during start up. You will need to edit your computer's drives or start up commands and delete the command that is causing this to occur. This would not be a file that from Workspace that is causing the issue. It appears that your local system is still trying a program that no longer exists on the system. We suggest researching support documentation related to your local system to remove the DriveMap.
It has to be a file from Workspace, it seems to me, or a system file that has been altered by Workspace. This didn’t happen before I installed Workspace. It started happening out of the blue... hadn’t added any files to online storage or accessed my online file folder for a month or more, and this event began occurring, at times rendering my computer unusable; that message pops up as fast as I can dismiss it, many many times... Intercepts all key strokes.
I’ve looked at my account’s startup items; nothing there. And iMacHardDisk/Library/Startupitems has only a backup program in it.
Has anyone had this problem and found a fix?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running OS X 10.7 or later, open LaunchPad. Click Utilities, then Terminal in the page that opens.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Copy or drag — do not type — the line below into the Terminal window, then press return:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
Step 2
Repeat with this line:
sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfix|x)/{print $3}'
This time, you'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up. You don't need to post the warning.
Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
Step 3
launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}'
Step 4
ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 5
osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
Remember, steps 1-5 are all drag-and-drop or copy-and-paste, whichever you prefer — no typing, except your password. Also remember to post the output.
You can then quit Terminal.

I have my i Pad connected to my computer and I still get error message there was a problem connecting to the server

I was having problems connecting to my app store and safari, any games or anything that required going out to a server. I rebooted my wireless several times it is working and it shows a signal on my iPad so it was suggested I go into settings and do a reset. I have done this and it still is not working. the error message when I try to sign in with an Apple ID is "there was a problem connecting to the server". I even get this when I am connected directly to my computer through Itunes
Any suggestions?

Sounds more like you have a problem with your apple id. For starters go to that page click manage my apple id and singn in. If you can't sign in reset password.
https://appleid.apple.com
if you can sign in there, try to sign in to itunes on your computer.

There was a problem connecting to the server (...)

Hello, all. First time posting here, so I'd like to greet the community.
I've been having this small problem for some months and never managed to fix it. I've searched the forums countless times and found many discussions related to the same message, but with different causes and solutions. None of them applied to my case.
Every time I open Mail preferences, my system freezes for a few seconds and a message pops up stating "There was a problem connecting to the server (...)":
I believe this has to do with the fact that, when I first bought my MacBook, I added a custom sound on the New Messages Sound preference that was stored on a hard-drive connected to my home network. Eventualy, I did copy said sound file to my MacBook and selected it as my custom sound for new mails, removing the previous one from my list of custom sounds. Still, once I disconected this hard-drive from my home network, I started receiving the mentioned message. It must still be searching for the sound file that was stored on the server, regardless of the fact that it's no longer selected as my new messages sound or added as a custom sound.
What's annoying about this is the fact that, ever since then, every time I receive a new email, the sound plays long after the notification alert pops up. Not really a serious issue, but I'd like to know how to solve it.
Many thanks in advance!

Please follow these directions to delete the Mail "sandbox" folders. In OS X 10.9 there are two sandboxes, while in 10.8 there is only one. If you're running a version older than 10.8, this comment isn't applicable.
Back up all data.
Triple-click anywhere in the line below on this page to select it:
~/Library/Containers/com.apple.mail
Right-click or control-click the highlighted line and select
Services ▹ Reveal
from the contextual menu.* A Finder window should open with a folder named "com.apple.mail" selected. If it does, move the selected folder — not just its contents — to the Desktop. Leave the Finder window open for now.
Log out and log back in. Launch Mail and test. If the problem is resolved, you may have to recreate some of your Mail settings. You can then delete the folder you moved and close the Finder window. If you still have the problem, quit Mail again and put the folder back where it was, overwriting the one that may have been created in its place. Repeat with this line:
~/Library/Containers/com.apple.MailServiceAgent
Caution: If you change any of the contents of the sandbox, but leave the folder itself in place, Mail may crash or not launch at all. Deleting the whole sandbox will cause it to be rebuilt automatically.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.

There was a problem connecting to the server "10.0.1.30"

In the last couple of days I have started getting the error "There was a problem connecting to the server “10.0.1.30”" popping up on the screen. Nothing to my knowledge has changed and I have no devices on my LAN that have an IP address in this range. All devices IP addresses are 192.168.20.1xx and my router's IP address is "10.106.75.57", subset mask "255.255.255.255", gateway "10.106.75.57", DNS "10.5.80.241 , 10.5.68.232" (Router is NetComm NF2 with attached AirCard 320U USB 3G/4G modem).
A couple of weeks ago I switch from using a Sierra (NetGear) Aircard 760S Hotspot Modem (default IP address of 10.0.0.138) using the AirCard Hub wireless router (IP address 10.0.1.1) to the NetComm router AirCard modem combination.
If I Ping "10.0.1.30" the results are as follows:
"PING 10.0.1.30 (10.0.1.30): 56 data bytes
Request timeout for icmp_seq 0
Request timeout for icmp_seq 1
60 bytes from 10.5.70.11: Communication prohibited by filter
Vr HL TOS Len   ID Flg off TTL Pro cks      Src      Dst
4 5 28 5400 caf4   0 0000 3e 01 d159 192.168.20.109 10.0.1.30 "
This error message is annoying, but apart from that everything appears to be working just fine. Is there a way of tracking down what is attempting to call 'server"10.0.1.30"' and stoping it. I.E. is there a quick and simple fix?
Hardware Overview:Model Name: MacBook Pro
Model Identifier: MacBookPro8,3
Processor Name: Intel Core i7
Processor Speed: 2.3 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 8 GB
Boot ROM Version: MBP81.0047.B27
System Version: OS X 10.9.4 (13E28)

There are many possible causes for this issue, and it may be hard to resolve. Please take each of the following steps that you haven't already tried. Back up all data before making any changes.
Step 1
If you get the alert as soon as you log in, it's probably caused by one of your login items or by software that otherwise loads at startup or login. Ask if you need help identifying it. A known offender is "AdobeResourceSynchronizer," which is a component of some Adobe products. See also this discussion.
If you get the alert in the login screen before you log in, stop here and ask for instructions.
Step 2
If there's an icon representing the server in the sidebar of a Finder window, hold down the command key and drag it out.
Step 3
In the Finder, press the key combination command-K or select
          Go ▹ Go to Server...
from the menu bar. In the upper right corner of the window that opens is a Recent Servers popup menu represented by a clock icon. From that menu, select
          Clear Recent Servers…
and confirm. Test.
Step 4
Open the Printers & Scanners pane in System Preferences and delete any network devices you no longer use.
Step 5
Triple-click anywhere in the line below on this page to select it, then copy the text to the Clipboard by pressing command-C:
~/Library/PDF Services
In the Finder, select
          Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return. A folder may open. If it does, move the contents to the Desktop, or to a new folder on the Desktop. Log out and log back in. Test. If there's no change, put the items you moved back where they were and continue.
Step 6
Open the folder
~/Library/Preferences
as in Step 5 and move the file named "loginwindow.plist" items in that folder to the Trash, if it exists (it may not.)
Log out and back in again, and test.
Step 7
Other possible causes are references in the iPhoto, iTunes, or iMovie library pointing to the server, and bookmarks in the Preview application.
Try rebuilding the iPhoto library.
Step 8
Triple-click the line below to select it:
/System/Library/CoreServices/Directory Utility.app
Rght-click or control-click the highlighted text and select
          Services ▹ Open
from the contextual menu.* The application Directory Utility will open.
In the Directory Utility window, select the Directory Editor tool in the toolbar. Select Mounts from the Viewing menu in the toolbar, and /Local/Default from the node menu, if not already selected. On the right is a list of names and values. By default, the list is empty. If it's not empty, post a screenshot of the window and stop here.
*If you don't see the contextual menu item, copy the selected text to the Clipboard (command-C). Open a TextEdit window and paste into it (command-V). Select the line you just pasted and continue as above.
Step 9
Open the following file as you did in the last step:
/etc/auto_master
It will open in a TextEdit window. The contents should be exactly this:
# Automounter master map
+auto_master          # Use directory service
/net               -hosts          -nobrowse,hidefromfinder,nosuid
/home               auto_home     -nobrowse,hidefromfinder
/Network/Servers     -fstab
/-               -static
If there are any other lines in the window, post them. Otherwise, close the window.

Problem connecting to the server Timecapsule

Similar Messages

Maybe you are looking for