Problem connecting two storage networks

Hello,
I connect two datacenters with 10GB modules. I'm using single mode fiber, it has 10Km between datacenters. Now I need connect the storage network in both datacenters using the same fiber. The storage networks use FCoE.
What solution can I use to connect the two storage networks. My budget is really limited.
Storage Network 1---------Network 1-------Fiber---------Network 2------Storage Network 2
Thanks for the help.

Brigid,
There seems to be two aspects:
One is to get the end points to coincide. You may tick View>Snap Guides, then click one path by the end Anchor Point and drag it to snap (Smart Guides say anchor when you are there).
The other is to get rid of the gap in the stroke(s), You may join the paths into one, dragging across the coinciding Anchor Points with the Direct Selection Tool and Ctrl/Cmd+J, or you may keep the separate paths and change the Cap to Round in the Stroke palette/panel which will give you a rounded outer appearance); I presume the former is what you wish, in which case you may choose between Round and Miter Join.

Similar Messages

When I enter my password to start my atv it tells me, that "there was a problem connecting to the network." My Ipad works fine but not my new atv. I have reset my password multiple times with no help. I have also rebooted my wireless server.take it bac

When I enter my password to start my atv it tells me, that "there was a problem connecting to the network." My Ipad works fine in my house, but not my new atv. I have reset my password multiple times with no help. I have also rebooted my wireless server. Do I take it back?

Where is everyone???? Does anyone have an answer???
Allik1

I had no problem connecting to my network and now all of a sudden I can't connect. Instead of prompting me for a password it comes back and says unable to join the network ("name") and then the option is Dismiss. Anyone else have that problem?

I had no problem connecting to my network and now all of a sudden I can't connect my iPad. Instead of prompting me for a password it comes back and says unable to join the network ("name") and then the option is Dismiss. Anyone else have that problem? I've gone thru all my settings and can't seem to find a way to log into my network. Don't get the option to put in my password. It just give me the name of my network and option of dismiss instead of password.

1. Turn router off for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings

Problem connecting two seperate straight line paths. Please help!

Hi there, I'm new to illustrator and have been having a problem connecting two straight line paths. They never seem to line up correctly. Attached is a photo of the problem. I assume this is an easy fix but I can't figure it out myself.

Brigid,
There seems to be two aspects:
One is to get the end points to coincide. You may tick View>Snap Guides, then click one path by the end Anchor Point and drag it to snap (Smart Guides say anchor when you are there).
The other is to get rid of the gap in the stroke(s), You may join the paths into one, dragging across the coinciding Anchor Points with the Direct Selection Tool and Ctrl/Cmd+J, or you may keep the separate paths and change the Cap to Round in the Stroke palette/panel which will give you a rounded outer appearance); I presume the former is what you wish, in which case you may choose between Round and Miter Join.

My apple tv gives a msg " there was a problem connecting to the network " check your settings and try again (5) - sometimes it comes with the number 3905 - i have tried all the suggestions from reset, restart, to switching and unplugging everything -

I was trying to download a movie and then it said there was a problem connecting to the network , check your settings and try again (5) . I tried all the various suggestions already in the discussions including restore, restart, unplugging everything etc - still doesnt work. Any other new ideas? I bought my apple tv just a few days ago and am really annoyed its already run into problems

Reboot router, make sure it's up to date. If on wifi try ethernet. Make sure DNS is set to automatic (settings - general - network).

HT1595 I have 6 other apple devices that have no problem connecting to my network, but my Apple TV will not

I have 6 other apple devices that have no problem connecting to my network, but my Apple TV will not, any ideas?

1: Unplug / shut off the router for 30 seconds
2: Retore or unplug apple tv (If you unplug it, let it sit for 30 seconds as well)
3: If all else fails try moving the ATV and router closer to each other, if nothing works I would consider it a defect as Apple products generally have great quaility and you never know what goes on behind warehouse doors!

Problem connecting two trunks to sip provider using same CUBE

We need to connect two SIP trunks from service provider to Cisco CUCM 7.1 using CUBE “Cisco 2821”, SP using the following configuration:
First SIP PSTN Link Configuration(In-Out DID/DOD 218 7700 – 218 7799)
Customer IP Address =   10.196.191.158/30
SP IP Address = 10.196.191.157/30
Protocol= SIP
SIP Port = 5060
Transport Protocol=UDP
Voice Codec= G711 A-Law
DTMF = IN-Band DTMF without RFC2833
Signaling IP address = 10.201.20.49
IP Address 10.201.20.10 (Media IP) must be visible from IP PABX
Second SIP PSTN Link Configuration( Inbound Only 920009999)
Customer IP Address =   10.196.192.94/30
SP IP Address = 10.196.192.93/30
Protocol= SIP
SIP Port = 5060
Transport Protocol=UDP
Voice Codec= G711 A-Law
DTMF = IN-Band DTMF without RFC2833
SIP server IP address = 10.201.20.49
IP Address 10.201.20.10 (Media IP) must be visible from IP PABX
When we tried to configure both links on the same CUBE we faced two problems:
-          Routing issue, as we can’t route traffic using single CUBE through two different interfaces to the same destination “ i.e we have to configure static route commend (ip route 10.201.20.49 255.255.255.255 10.196.191.157 & ip route 10.201.20.49 255.255.255.255 10.196.192.93), sip traffic coming from one link can’t be sure to send it back to the same link.
-          SIP media & signaling control binding issue, as CUBE support sip binding using one interface only “one IP Address”, if we not using binding commands on the CUBE we can’t receive any calls though any link.
We have two options:
SP to send both traffic on the same trunk link
Or
Have another CUBE for the second link.
Attached network diagram.
Any solution?????
Regards,
Ahmed Rizk

I didn't mean NAT CUCM, I meant the interface towards it. But since you're using a single interface then yes that is what you NAT. You have a lot going on in that config. Probably a lot more than you need. Like I said you should work on this in two legs. CUBE to ITSP, and then CUCM to CUBE. You're trying to make the whole thing work in one shot which is going to cause you some headaches.
Install XLite free version. In the account settings set your UserID to a generic 10 digit phone number, domain to something generic, then at the bottom set the Proxy Address to the IP of your CUBE. The media ports will be negotiated dynamically between the CUBE and the ITSP. Since you said you're not registering you will also need to give the ITSP YOUR peer IP (this is how they secure the trunk) which is whatever IP you're sourcing from when you leave your network (what you're NAT'ing the CUBE to).
For testing, reduce your config to something like this:
voice service voip
allow-connections sip to sip
allow-connections h323 to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
signaling forward none
sip
dial-peer voice 10 voip
description CUBE_TO_ITSP
session protocol sipv2
session target ipv4:SIGNALING IP PROVIDED BY ITSP
destination-pattern [2-9].........
codec g711ulaw
dtmf-relay rtp-nte sip-notify
no vad
dial-peer voice 20 voip
description ITSP_TO_CUBE
destination-pattern .
session protocol sipv2
session target ipv4:Eventually your CUCM IP...for now set it to your computers IP.
codec g711ulaw
dtmf-relay rtp-nte sip-notify
no vad
Use XLite to place a phone call from your PC (if you have a mic and speakers you can have audio if the call connects). This should come pretty close to getting your outward leg established. Once you get this part working you can add in more codecs and translation profiles if you want. Let me know what happens. Include any debug or packet cap results if you can.

One Z10 works fine, the other has problems connecting to mobile network

Hi, my wife and I both have Z10's, and we're both on the same mobile network (Wind Mobile in Canada). The wife's Z10 seems to have no problems connecting to or staying connected to Wind Mobile. Mine on the other hand seems to randomly drop the connection, or has trouble obtaining connection, and sometimes ends up roaming.
The only difference between the two Z10's is that hers is purchased through Wind Mobile itself, and it is locked to their network for the moment. I purchased mine a bit later, and I bought mine directly through Blackberry's online store, and mine is therefore unlocked. What I have to do sometimes is turn off the mobile connection, and turn it back on, and it works after I do that. However, that's annoying, as I'd rather have it automatically retry the network connection so that it doesn't go roaming within my own city.
Solved!
Go to Solution.

If you're passing by a Wind store in the near future, why not drop in and ask if they'll swap SIM cards for you? It could be something with the SIM.
In the meantime, try resetting your phone. This is equivalent to doing a battery pull and it's usually the first thing I recommend when troubleshooting an issue. Simply press and hold your power button for about 15 seconds until you see BlackBerry on your screen. Don't release the button before that and ignore anything that appears before BlackBerry.
Let us know if either of those solutions helps you.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

Problem connecting two ipads to wifi

I'm sorry if this has been asked already. I'm having trouble connecting two ipads or an iPad and iPhone to my home wifi. Ive found that if I have an iPad or iPhone connected to my wifi, then i cant connect a second iPad at all. I have to turn the wifi setting off on the connected device, then I have to completely turn off the device I'm trying to connect, turn it back on, then it will accept the wifi password & connect. Long of the short, my friend and I can't use our ipads at the same time on my wifi. Is there a setting I could change on my router to fix this problem?

Or u cn try chk hw many ip address ur router was set to allocate.
Another router setting u cn try is set to WEP shared instead of WEP Open. I not sure if this solve, i set to WEP Shared bcos previous my nintendo DS only work with with WEP shared.
My home network is able to connect with 2 ipad and 2 iphs all at the same time, sometime with an additional laptop. Meeting 5 devices.

My Apple TV is reading " There was a problem connecting to the network" error - 3906

I have reset all network components and the Apple TV. I first set up Apple TV and it worked beautifully. The next time I turned it on it gave me the error message. I have tried reconnecting to the netwrk multiple times. I have my laptop and my ipad connected to the network, but the Apple TV will no longer connect. I am out of solutions. Any suggestions would be greatly appreciated. Thank you.

I had the same problem. I just solutioned it just by disabling MAC Address filtering in my LinkSys router. This is strange as I did enter the address of my ATV3 in the list of allowed devices in the router configuration software.
The truth is that it now works! I just seems that ATV is not compatible with MAC Address filtering.

My phone is having problems connecting to wifi networks

Hi I have the blackberry curve 3G smart phone and for the past week it has been connected to the local wifi at my accomadation in phuket. I am from South Africa and my service provider failed to activate my international roaming so I was using the wifi for BBM. It would automatically connect perfectly everytime I arrived at my bungalow (and yes BIS is part of my cellular package) and has been active for atleast a year so far. For some reason today it is unable to connect. it says " failed to obtain an IP address" . after attempting to connect multiple times it states "Device failed to acquire an IP address. The failiure could be due to an incorrect WEP key.", I have checked the WEP key multiple times on my laptop and Im entering the correct one into my black berry.
Here is what I have tried so far:
- Turning the phone on and off
- Removing the battery and re-inserting it
- I have tried manually connecting to the network
- I have tried connecting with the phone set to "automatically obtain IP address and DNS"
- De-activating "automatically obtain IP address and DNS" and entering the IP address myself, once i have done this it states that I am connected to the network but I am still unable to use my internet browser and instant messaging services.
Any help would be greatly appreciated

I bought my iPhone 3 days ago, and am also having trouble connecting to ANY wifi networks. The iphone scans for networks, sees them, but fails to latch on once the connect buttn is selected. I've called iPhone tech support and ran through a multitude of tests with them, including full system restores, trying the main power switch, flight mode toggles etc..
The conclusion from iPhone telephone support was that the unit is faulty and needs to be returned to be checked out.
I'm starting to wonder with the numerous wifi connection problem reports I've found on the web about others having trouble, whether this product was rushed to market with half baked software...

Having problems connecting to wireless network when extended

Hi. I recently switched over to a mac and love it!! However I recently purchased a Time Capsule and a Airport Extreme to extend the network and am having problems. My macbook continues to log onto the guest network and not the main wireless network. When I try to switch to the main network it asks me for the WPA password and then it tries to connect but then states connection timeout. When I remove the guest network from my list of networks it will not allow me to connect to the internet at all through the main wireless network unless I power down the airport extreme that is extending the network. One final note, I have no problems at all if I keep the airport extreme shut down and do not extend the network. It seems it is not the time capsule but the airport extreme. One other additional note, my windows machines are having no problem connecting to the main wireless network with the network extended!!

Welcome to the discussions!
A few thoughts:
If you have not already done so, it will makes things easier to troubleshoot if you assign separate names to your "main" and "guest" network. By default, they are the same name and it sometimes is difficult to know what network you are actually connected to.
Open AirPort Utility, click Manual Setup
Click the Wireless tab below the row of icons
Look for an "options" button. This should allow you to assign a separate name for the "guest" network.
The "main" network can be extended, but the "guest" network cannot be extended. Your other computers may be connecting to the "guest" network unless they are newer devices capable of connecting at 802.11n only 5 GHz.
It's easy to make a mistake when setting up the "extend" feature. Please check the following settings for your TC and AirPort AX or AEBS (You posted in the Airport Express forum, but talk about having an AirPort Extreme in your post).
You will use AirPort Utility - Manual Setup as above to check your settings as follows:
_On the Time Capsule:_
Click the Wireless tab below the row of icons
Wireless Mode should be "Create a wireless network"
Make sure there is a check mark next to "Allow this network to be extended"
_On the AX or AEBS:_
Click the Wireless tab below the row of icons
Wireless Mode should be set to "Extend a wireless network"
Make sure there is a check mark next to "Allow wireless clients"
The Security and Password settings must match the settings of the TC exactly
You should now be able to identify whether your computers are connecting to the "main" or "guest" network. If your computers are connecting to the "guest" network, they are connecting directly to the Time Capsule regardless of their location in relation to your device that is extending the network.
Using your Mac, if you hold down the "option" key while you click on the fan shaped airport icon at the top of the screen, you will be able to see whether you are connected to the "main" network (802.11n 5 GHz) or the "guest" network" (802.11 2.4 GHz).
The BSSID will display the AirPort ID of the device that you are connected to. By noting the ID of your Time Capsule and AX or AEBS, you will know which device you are actually connected to on the network. As you move closer to the "extending" device, your computer should automatically switch to the device with the strongest signal.
Please post back on your findings.

Problem Connecting Two Monitors

Just set up a new HP Mini 300-30 with two monitors. Monitor connection is through a device I bought that has HDMI cable connecting to back of HP Mini and two outlets on device to connect two monitors using VGA cables that came with each monitor. Monitors work but are set up with mirror image and I have not been able to find a way to make each monitor run indpendently. If I use keyboard and press Windows key + P it brings up a screen where I can select monitor options. I select the option to run separate monitors but nothing happens. I believe I have tried everything but the correct way.

Hello @RedWingFan,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your desktop computer is not able to display two independent images, and I would be happy to assist you in this matter!
To ensure your displays are configured correctly, I recommend following the steps in this document on Using Two or More Monitors with One Computer (Windows 8).
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Problems connecting two wireless rooters without cable.

How do I set two Roter, if one is already configured.
The other is a model Edimax BR-6504n.
For the first Roter I know the MAC address and no password ... I connect with any laptop without the password, I am interested in someone who knows better to enlighten me.
I know from the manual that the rooter supports the following options:
AP
AP Bridge-Point to Point
AP Bridge-Point to Multi Point
AP Bridge-WDS
And in the MAC section of the AP Bridge-Point to Point I put the MAC of the first rooter, and here is the problem cause I do not know the channel of the first rooter. Is there a program or something that find the channel.
I have access only to the second rooter.
And it is important what options to set so that i reduce the number of combination to try when i put the channel.
What option should I put to the LAN? to make the ip different from the first rooter?
IP of first rooter: 192.168.2.100-200 I think this are the range ip of the first rooter.
Should I put the second rooter IP in another range like 192.168.1.*.* or leave it to 192.168.2.*.*?
The problem is that I must link them wireless not by wire.
So how do I connect the second rooter to the first so that I can extend the range of the wireless.
For those interested, here is found the user manual.
http://www.edimax.com/en/support_detail ... 2&pl1_id=1
Or just download the attached file.

In this mode, you canconnect your wireless rooter with another, to combine two access points and expend the scope of the wireless network, and all clients of two wireless rooter will think they'rw on the same physical network.....etc see the image below.
So i think it must work...but i du not know how to config them.
Look in this section.
[url=http://i.imagehost.org/view/0198/Capture_10][img]http://i.imagehost.org/0198/Capture_10.jpg[/img][/url]

Sporadic problems connecting to Windows Network

I'm one of two Mac persons on a Windows network here at work. The problem is that we often can't connect to the server/network. It's a Windows 2003 Server, and we're both running on Tiger.
What puzzles me is that we sometimes can log on to the network, and sometimes not.
Is there any explanation (or preferably a solution).
Thanks in advance!
Message was edited by: Snuf

IT should know this from their Logs, but if you have access to the Server, check it's time & the Macs' times when you can't connect.
For the other problem, might try to use one of these lines in terminal...
sudo ipconfig set en1 BOOTP;sudo ipconfig set en1 DHCP
sudo ifconfig en0 down;sudo ifconfig en0 up
Use en0 if Ethernet, en1 if Airport, in both places in either line.

Problem connecting two storage networks

Similar Messages

Maybe you are looking for