Problem connecting wifi to LG BD670 wifi dvd player?

I cannot connect the LG BD670 3D wifi dvd player to my Airport Extreme. I have a strong signal. But when I input my password, I get this message:
I have contaced LE support and tried everything they suggested. They say: “Access Point Connection failed. Do want to retry?”
I see, can't say is a problem with the wireless card in the player since it does detect the name of your router, the error Access pointconnection failed refer to router, we are not getting access to it
They also said to lower my network security from WPA2 to WAP. WPA2 was to high a security. Does it matter?
Does anyone have a suggest?

Similar Messages

Problems Connecting iPod Touch 32GB to WiFi

Hi,
I have just purchased an iPod Touch 32GB and am having problems connecting to a server. I am using a Netgear DG834 router to connect to Orange. Netgear is now showing as checked on the Wi-Fi Networks page on the iPod with strong signal strength but I keep cannoy getting the message "could not connect to server" whenever I try any of the applications. Needless to say, the internet connections on my laptop and desktop are working perfectly. Thanks. Grant

Have you tried resetting your router? sometimes this is all you need to do to get the IPT to work properly. If you are using any type of security such as WEP or WPA2 then you are going to need to enter your password. Try a reset and then go to your wifi settings in the IPT and select your router and then click on the little blue arrow and check under DHCP and make sure you have an IP along with a router Ip and DNS entries. If you don't have a router IP or DNS entries try and renew the lease.
If you can't get it to work then reset the router again but this time try it without any security and do the same procedure as above. If that still doesn't work then the only other thing I can suggest is to look on Netgears website and see if there is a firmware upgrade for your router and to give that a try.

Creative 5200 inspire 5.1 speakers connection to my onida 5.1 dvd player

Hey guys i have a onida 5.1 channel dvd player and a set of creative 5200 inspire 5.1 speaker set.
As per your instuctions shown on the site i bought 3 pcs of single stereo to dual rca cables and attached it to the 5.1 output as per your picture shown but only 2 spkrs and the woffer worked .
Then i connected the front left n right as per your instuctions and the rear left & right i connected to the regular audio red and white plug on the dvd player where you would have connected it to your tv and then at least 4 spkrs and the wooffer is working now i wanted to know how should i make the centre speaker work pls advice
would request you to pls send me a reply on my mail id if you dnt mind ie: [email protected] as i dont visit this site very often pls request you for the same
hope you could help me wit the same pls thanx

i have bought a creative sound card namely " creative live 24 bit 7.1 " will me creative 5200 spkrs work {all 5 FL,FR,RL,RR & CENTRE}
pls advice as i could change my sound card if it isnt compatible.
thnx

Connecting 4.1 (4400) to TV/DVD player

Hi all,
I have got Sony TV and Sony DVPNS50P dvd player.
Can I connect creative 4.1 (4400) to these directly.
Please advise...
thanks...

No, it won't be true surround sound, a 2-channel output will only deliver 2-channel sound. For true surround sound, on that DVD player, you'll need 5.1 speakers that you can connect to the optical or coaxial digital output (so a 5.1 speakerset with a decoder, like the Inspire GD580).
You could use 2.1 speakers, it would give you the same effect as the 4.1 4400 speakers, there wouldn't be much difference.
Cat

Problem Connecting iPad or iPhone to Wifi (Linksys E1000)

I recently moved from my parent's house to a condo and I am having trouble connecting my iPad or iPhone to my WiFi. I have not problem with my main desktop (connected to the router via ethernet), but my iPad and iPhone fails to connect to the network. I don't have a problem finding the network (FunnyWillow) but when I try to log in, it says "Failed to join "FunnyWillow" - "Unable to join the network "FunnyWillow" ". How do I resolve this problem?
Solved!
Go to Solution.

Alright, my current firmware version is (v1.0.01 build 7Apr 15, 2010). I tried to update it by downloading version 2.1, but when IZArc opened, there was nothing in the .bin to extract. I checked my status afterwards on (http://192.168.1.1/Status_Router.asp) and it still says I am using the v.1.0.01... version.
I reset the router, and network and tried to update the firmware and the samething happened with the update. I tried to connect my iPhone/pad and the same error message appeared. I have a good feeling that getting that firmware update would solve it, I guess U don't know how to go about it.

How to connect the I-Trigue 5600 to a DVD player???

I got a set of I-Trigue 5600 and thinking of connecting all 5 speakers and woofer to the back of DVD player to get the surround effect when watching DVD. The problem is I can just plug all 5 speakers to the back of the DVD player but how can I connect the sub-woofer to the DVD player as there is no cable to connect them together? Is there some sort of cable or adapter I can buy to connect them together? Thx in advance for any help!!!

have you tried that setup already?
my guess is that the subfrequencies are still combined with the front channels, and if I correct, your speakersystem will redirect them to the sub. just give it a try.
regards

How to connect DVD player to FIOS TV (with standard TV)

The Verizon techs installed my FIOS system. I already have the router, DVR and standard TV connected and working. How do I add a DVD player to the mix?
I found wiring diagrams for my FIOS DVR, but they do not include my configuration. Here is what I found:
http://www22.verizon.com/ResidentialHelp/FiOSTV/Receivers/Wiring+Diagrams/Motorola+7232+HD+DVR/12763...
The above diagram includes an A/V receiver, which I don't think my configuration includes. The tutorial does not offer a choice of configuration that is just the DVR, standard TV, and DVD player.
Where do I find a wiring diagram that connects my DVR, standard TV and DVD player? Do I have to do anything to the router when I connect the DVD player? Sometimes I see references to set top boxes--are they the same thing as the DVR?
Thanks in advance.
Solved!
Go to Solution.

Sorry to hear about you trouble.
If you are using a standard TV you need to check the back ports for RCA connections. They are listed as video/audio inputs, with color coding.
From your DVD player use RCA output jacks, yellow for video, red and white for audio
Take other end of RCA cables and connect to TV inputs at the back
Set your TV to what ever input was used for DVD player and this should allow you to see DVD from TV.
I sent you a PM if further assistance was needed.
Jerrold_VZ
Verizon Support
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

Connecting Creative Inspire 5.1 speakers to DVD player

Hi,
I have a LG DVD Player (DSI 8352) which gives 5.1 home theatre (dolby decoder) output.
If I buy Creative Inspire 5.1 speakers (5200 or 5700), how do I connect them ? Through RCA Stereo cables ? Would there be any compatibility issues ?
Please suggest the 5.1 speakers that would suit my requirement (no decoder / only amplifier) ..
Plz reply back to [email protected]
Thanks,Sambath

Creative offers many speaker systems that will fit your needs, without decoder.
You mentioned the Inspire 5700 system; this system comes with a decoder/amplifier, and wouldnt actually be what you'r looking for.
If your looking for awesome sound-quality, and good power, I can recommend the 5.1 Megaworks system, though this system can get quite expensive, you'll get what you pay for.
The megaworks (like "all" other creative speaker systems, got a built in amplifier in the subwoofer, where you connect all the speakers.)
To connect the speakers to the DVD-player, you connect the multichannel output on the DVD-player, to the multichannel input on the back of the subwoofer. (three stereo minijack inputs.)
You may need some RCA-to-minijack adapters, so that the multichannel audio cable that comes with the megaworks, will fit on your DVD-players output.

Inspire 5200 - connecting to DVD player?

Is there any way to connect this speaker system to a DVD player? Since the subwoofer doesn't have rca input jacks.

sanafabich,
If you DVD player have 5.1 channel RCA input jack, you could always get yourself some 3.5mm stereo minijack to dual RCA cable for the connection.
Jason

M4500 anable to connect with DVD player

Hi,
Kindly help me I am not able to connect my Creative M4500 speakers with DVD player.
Regards

Not sure what your asking as it should be very simple, you are talking about the X-fi front bay unit right? You have a DVD player with R&w outs, you simply connect to those and then the same R&W connectors on the bay unit. I believe its treated as Linein2 in the mixer. Should be very simple to figure out

Apple dvd player problem

Hi,
I've just spent an age authoring a dvd in dvdsp 4 and the disk looks excellent in everything apart from the apple dvd player. The problem seems to be that after the dvd player plays a video stream it changes its pixel aspect ratio settings to dv rather than square. So the menus all look great until a video is played, after that they all look really pixelated and bad. I have tried the disk in my under the tv dvd player and it looks fine and also VLC on my powerbook and that also looks fine. I have spent lots of time adjusting the original graphics to various sizes and as I said the disk looks fine on everything apart from apple dvd player (and looks fine on that untill a video stream is played).
Any ideas? this is my first post so i'm sorry if it makes no sense.
Thanks

I myself and a good number of my clients are unable to use Apple DVD Player because of this, the effect is vertical streaks on the screen much like filming the scene during a storm but with green or red rain.
Sorry Gary - never experienced this one before. I'm using 4.6.5 build 4.6.6 - what's yours? I know you have a good set up - but what is it.
More importantly - Flash floods in Corstorphine today too
Now your getting closer to me - i'm up in Buckstone - way up in the hills - although I did start building my survival boat after all the rain - are you near me?
Long shot - assuming you haven't tried this already - bin DVD Player and get a fresh copy, Graphics card issues - lets start the elimination process.
BB
G5 Dual Quad, G4 MDD, Powerbook, iMac etc etc Mac OS X (10.4.5) lots and lots of back up drives - just lots

Subtitles in Apple DVD player won't go away

This is not a Tiger problem per se- more of an Apple DVD player problem. I couldn't find a forum for the DVD app. If I'm in the wrong place, I'd be happy to post in the proper place if someone could point me in the right direction.
So I'm running os 10.4.7 on an 800 mhz iMac (flatscreen, "lamp" model), my version of the Apple DVD player is 4.6.5, framework version 4.6.6.
Here's the problem- whenever I watch a movie (this seems to happen only with American DVDs), these QT/OS X looking (beautiful crisp white letters on a highly transparent smokey grey field) subtitles appear, they are independent of the subtitles invoked by the subtitle button in the player- I can toggle through all the languages, they work fine, but the QT/OS X looking subtitles never go away- I'll have two sets running simultaneously. (Or just the QT/OSX one, when I set subtitles to "off")
While they are gorgeous and superior to the "other" set of subtitles (which I CAN control), in both visual appeal and intelligent placement, I would like to be able to turn them off.
I thought a handicap access feature in the System Preferences might have been involved, but it doesn't seem so.
Can someone help me turn this off? Incidentally, these phantom permanent subtitles weren't always here, though I can't really say when they appeared.
Thanks in advance for the help,
Nosloj2400

Do you have "Closed Captioning" (DVD Player "Controls" menu) turned on? You may have turned it on accidentally via Option-Cmd-T.

Apple DVD Player software not reading SPRM 4 correctly.

I am a DVD author and have recently run into an issue with Apple DVD Player not reading SPRM 4 (current title) correctly. I know this isn't the Apple DVD Player forum, but there doesn't seem to be one for that application, so here I am...
I have a disc (not authored in a Mac environment) that uses the value of SPRM 4 to track the last title played, and if it happens to equal the value of the main feature title, then use the "PLAY" button on the main menu as a resume.
Apple DVD Player seems to think that SPRM 4 equals this particular value all the time, regardless of what title last played, which is totally breaking my disc. The real kicker is that the disc works flawlessly on set-tops and in a windows environment.. just not on any Mac that I have tried.
Has anyone out there also experienced a problem with tracking SPRM 4 in Apple DVD Player? Is anyone from Apple reading these things, possibly someone who can flag this as a major issue?
I am positive that this specific to Apple DVD Player, because the disc works as intended EVERYWHERE else.
I have tried and experienced this issue across several Macs, and across several versions of DVD Player. It's consistent across all.
If anyone has any ideas, please respond.
Thanks,
Ben

these problems are well documented, use the search functions for plenty of solutions

Inspire A500: Is there any adapter for the TV or DVD Player?

I have recently bought the Inspire A500 and wanted to know if there was any possible way of connecting it to my TV or DVD Player?

The photo looks like one of the older MagSafe adapters, not the 't'-shape that shipped with 2011 models. I would imagine that if you took it into an Apple Store they would just tell you that it was damaged. I doubt that they would replace it.
However, I don't work for Apple and, were I in your shoes, I'd take my MBP with the adapter into an Apple Store and kindly ask if the adapter is covered under warranty (if you're still in your warranty period or under AppleCare). If it's not, be prepared to buy a new one.
Good luck,
Clinton

Using iTunes to create an MP3 CD that can be used on a DVD player

I recently attempted to create what I believed to be an MP3 CD from iTunes that my DVD player would be able to play. My DVD player was unable to read the CD (No Disc message). Come to find out that it creates the CD in a Mac format instead of an ISO 9660 format. Has anyone been able to create an MP3 CD from iTunes that a DVD player will load? If so what settings did you use?

The problem is solved. My new Sony DVD Player seems to handle whatever format my MP3 CD is created in even though the manual says nothing about a mac formatted CD. So I can now use iTunes or Toast to create MP3 CDs. My old JVC CD player is about 5 years old and even though the manual says it will read MP3 CDs and VCD CDs it never worked well on anything I created on a Mac

Problem connecting wifi to LG BD670 wifi dvd player?

Similar Messages

Maybe you are looking for