Problem detecting: add-on Maxtor IDE card on Solaris 10.

Hi everyone,
I am trying to install Solaris 10 -01/06- in a P3-700Mhz system.
The motherboard is kind of old, it doesn't recognize my 20GB primary HD.
So, I put a Maxtor IDE disk E-IDE controller card. It uses Promise Technology chip, full model name - Ultra 100 Tx2, chip model-PDC20268.
The card is good, and it detects 20GB driver in bios.
However, Solaris 10 doesn't seem to detect it. It keeps telling me "no disk found". so took me back to concole/dos screen.
I read on some there post, saying there is jumper for the Maxtor RAID disk controller. I have to adjust it order to make detection to work. However, it is not a RAID card, just a normal IDE expansion card.
I would like to ask for your help to see if Solaris 10 support thise type of add-on card.
Thanks

Hello Jason,
there is no need to "low-level" format the drive. The manufacturer did the low-level format (and management of bad spots) for you.
Have you tried to run analyze (either non-destructive or read-write) ?
Probabably you just want to create a filesystem on the new drive (this is what Microsoft format does in the last step), use the command newfs instead.
Michael

Similar Messages

I own a MAC Pro 3,1 (early 2008) and am running Mavericks 10.9.3 with no problems. I would like to add an I/O card to add USB 3 functionality or ESATA functionality but am unable to find a compatible card. As such my question...can I do this and if so wha

I own a MAC Pro 3,1 (early 2008) and am running Mavericks 10.9.3 with no problems. I would like to add an I/O card to add USB 3 functionality or ESATA functionality but am unable to find a compatible card. As such my question...can I do this and if so what is the best card?
Thank you

Have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"?
Also see:
https://discussions.apple.com/thread/6282459?tstart=0

[ PROBLEM ] Audio Control app wont recognise card properly

Hi
I have a X-Fi ExtremeGamer card in my Win 7 home premium setup and am struggling to set it up properly.
Long story short , I pulled out the X-Fi card and tried the onboard audio as I was getting an issue with the audio playing around using the creative drivers ( volume changes mid song, positional audio in games was often unusal ).
The Realtek stuff wasnt too bad but I wanted to try my X-Fi card again, it is suppose to be better after all.
Anyways...
I disabled the onboard audio , safe mode and cleaned all the realtek drivers out and any lingering creative drivers with Driver Sweeper, used CCleaner to clean up the reg and rebooted.
Installed the BETA drivers from creative and the audio works fine, but when I try use the crystaliser or other SB features the app complains
" The audio device supported by this application is not detected. The application will exit. "
I installed Daniel_K's drivers from a CD ISO he put out a while back, and the applications worked fine but the audio dropped in and out, so I downloaded the official creative drivers for my card and OS, and the application worked fine again but as with Daniels drivers the audio dropped in and out so I reverted to the beta drivers... and the audio dropped in and out as well.
I worked it out to being the volume controls on the creative 5. speakers , which every set of speakers I have bought from creative have had the same issue, the volume slider on the cable... after some use it messes up the audio and it becomes safer just to adjust the volume in the software.
After deciding the issue was with the volume slider on the cable, I wanted to re-install Daniel_K's driver pack so I could access the other features, now it suddenly doesnt recognise the device anymore, nore does the official none beta drivers from creative, nor does the latest PAX drivers ... all report the same issue:
" The audio device supported by this application is not detected. The application will exit. "?
I am starting to tear my hair out here, the audio works and the card is recognised in the Device Manager as 'Creative SB X-Fi' , I have clean the drivers , the registery , used the patch that fixes a bug where the update wouldnt recognise cards properly , re-re-re-re-re-re-re-re-re-re-re-re installed the drivers.... carefully EACH time.
I triple checked I was downloading the Win 7 64bit OS ver of the X-Fi ExtremeGamer drivers.
What now ?
ALSO Who thought it was a bright idea to put up the volume to 87% when you install drivers ? It also unmutes the volume if you mute it before restart, and it puts the volume back up to 87% if you dare to lower the volume before rebooting the PC to complete the install.
( NOTE: It only does this after the initial reboot to complete the install, subsequent re-boots leaves the volume alone )

I give up...
I sent a form to the tech guys , detailing the problem and outlining the steps I took to fix the issue...and they direct me to http://support.creative.com/kb/ShowA...aspx?sid=55438?, oh I can use Device Manager to uninstall , oh and Control Panel - Programs to unistall the Creative stuff ( note: I am being very sarcastic here ).
This is the information I sent the tech:
Detailed Problem Description:
Creative audio application does not recognise SB X-Fi card , card audio functions just cant control the feature set. Error msg : " The audio device supported by this application is not detected. The application will exit. " Suspect nVidia installing of HD audio drivers causing 4 (four) additional High Definition Audio Devices to appear in the device manager screen. Unable to uninstall these devices as Win7 auto re-reinstalls with generic MS drivers, can only disable. Creative SB X-Fi card listed in audio devices as 2 - SB X-Fi. Suspect the audio control application looks in the first slot and doesnt recognise the device and fails, doesnt look at the 2 ( second slot ? ) Tried a full uninstall including going to safe mode and removing drivers with Driver Sweeper, CCLeaner to clear out registry entries and removed the card, booted to windows without the card , re-seated the card and re-installed the drivers. Forum entry for this problem at: http://forums.creative.com/t5/Sound-Blaster/PROBLEM-Audio-Control-app-wont-recognise-card-properly/td-p/57930
Thank you
and this is the advice I got ...
Thank you for contacting Creative Labs.
To avoid installing the incorrect driver on your soundcard, we suggest that you do a full uninstallation using the guidelines, steps provided in our website. Shutdown your PC then take out the card and make sure to place it on another slot. Second, disable your onboard audio and if your graphic card comes with any audio support as well, disable this feature.
Uninstalling Sound Blaster Drivers and Applications(Windows 7)
http://support.creative.com/kb/ShowA...aspx?sid=55438
Do not hesitate to add as much information in the next reply so we can understand the entire issue and assist you find the right solution or suggestion.
Best Regards,
... seriously ?

I am trying to add a new credit card and it keeps telling me that I have to enter a valid security code...I have tried 2 different cards and it is doing the same thing. How do I get past this?

I guess it has been a year since I last purchased something on I-tunes and my account is saying that they couldn't authorize my card for some of my purchases. I am trying to add a new credit card to clear this up and it keeps saying that I have to enter a valid security code. I have tried 2 different cards and I get the same thing. I have also added an I-tunes gift card and that isn't clearing up the money that I owe. It is showing that I have a $25 credit for that. How do I fix this, I have been trying for days and all I have got from the e-mail tech support is that its my credit card issuer that is causing the problem. Thats not correct because one of the credit cards that I am trying to use, is a prepaid Visa gift card. I know that these work on I-tunes because I have used them before in the past. I am getting very frustrated with this whole process, I just want to clear up my account and buy some new music!! HELP!!

You probably ran into blocks & locks.
iTunes Store Support
http://www.apple.com/emea/support/itunes/contact.html
They'll sort it out.

Setup could not detect any Sound Blaster Audigy card on your system

Hi from Barcelona!
I've a Soun Blaster Audigy card (Model: SB0090)
I tried to install the Audigy software and drivers from the original product CD but Setup was unable to find Augigy hardware and halted the installation!
"Setup could not detect any Sound Blaster card on your system. Please ensure that your Sound Blaster hardware is properly installed before running this Setup program"
By the way. Manually the sound drivers can be installed working only front speakers of the 5. Creative system
I tried a clean installation of Windows XP and Windows 2000 PRO (reformatted the hard dri've) but Audigy install CD still could not find Audigy hardware.
I've changed the card to a different PCI slot with the same results!!! Damaged?
What is happening? I need a solution!! Many users have this problem to with other Sound Blaster cards and models...

ADSLNEW wrote:
It seems to be an important BUG of Creative Sound Blaster Audigy cards related with EEPROM!!!
Yes, indeed, that is my theory as well. After much ****hing and on-line research, it seems that this problem has been around since 2002. From Creative Labs point of view, it appears they view this as "pilot error" -- the user has installed the card in a system that is not fully compliant with the latest standards -- specifically Microsofts ACPI (configuration and power management). A wide variety of configurations and/or actions seem to cause the PCI subsystem ID in the Audigy EEPROM to be erroneously overwritten -- including certain older motherboards, certain older PCI cards, and perhaps other actions.
Once the subsystem ID in the EEPROM is overwritten and has garbage information, many or all of the Creative applications cease working and various sound problems can arise. Attempts to reinstall the driver or update to the latest driver consistently fail becuase of the dreaded "Setup could not detect any Sound Blaster Audigy card in your system..." error message.
There appear to be four fixes:
) Get a replacement Audigy card from Creative, but only after you perform their prescribed troubleshooting steps to prove that the card is indeed the source of the problem. Apparently, the steps include installing the card in another PC. Apparently, Creative in Europe is more willing to replace your card than Creative in the US. It's up to Creative Labs whether or not they issue you an RMA ("Return Material Authorization").
However, this fix will fail if the root causes of the EEPROM error are not corrected. Apparently, Creative Tech Support isn't always a foolproof source of guidance, so the burden is on you. The root cause MUST be corrected before the new card is installed, or the same problem will happen all over again. Eliminating the root cause may involve replacing your motherboard, replacing other PCI cards, or manual configuration (disabling ACPI).
2) Reprogramming the EEPROM. This is for advanced PC owners only, because it involves desoldering the EEPROM, programming it, and resoldering (and even lifting some pins to prevent reprogramming). There are instructions on how to do this posted in the German Creative Labs discussion board, by a Russian (!). I have links for those who are interested.
3) Removing the Creative drivers and software (using Clean Sweep procedures and third party utilities), updating again using Windows XP SP2, then physically moving the card to different PCI slots (multiple times if necessary), until ACPI Bios writes the proper information into the EEPROM. You can then reload the drivers.
Again, the root causes of the problem must be removed or your fix will only be temporary (a day or two). This solution also seems to be very dependent on the specifics of your system (motherboard, PCI cards, etc.).
4) Some people have had success in by-passing the step in the driver installation process where they check for the Audigy card subsystem ID, using a utility called CTZAPxx on the installation CD. Then then manually install each of the applications they need to use.
5) Use the open source driver from the kX Project (http://kxproject.lugosoft.com/index.php). This driver (and associated utilities) does not depend on the detailed configuration of the card (i.e. they don't check subsystem ID) and appear to work fine even with cards with corrupted EEPROM.
This driver is aimed primarily at computer music applications, and opens up the on-card signal processing capabilities. The downside is that the Audigy 2 ZS does not have all of it's capabilities supported yet (e.g. Dolby Digital decoding, S/PIF passthrough, possibly some game sound features, THX, 24-bit recording, support for Hyperthreading CPUs, etc.). But scanning over the discussion boards, the user community seems to be MUCH happier with the performance and support associated with these drivers than with Creative's.
This is the direction I'm going. I'm not a big gamer and I don't really care about the latest in home theater audio performance. Basic 5. surround sound is all I care about, and I'm much more interested in computer music capabilities.
I have also lost faith in Creative Labs as a vendor to provide the support I want and need going forward. Just imagine if the Creative Labs were running the Space Shuttle program :smileysurprised:.

Asha 311 - add music from memory card

Hello,
I've encountered an issue with my Asha 311. I copied my mp3 files into phones memory card and I wanted to access and play them from phone's Music shortcut in the front page, however, it only finds music that is in the phone memory and ignores the memory card. How do I add music from memory card to that list?
Thanks
Solved!
Go to Solution.

Then do one thing.. make sure all the music files in your device are in the folder named music files in the memory card.. if not, simply move the files to that folder.. agian update the library and check..
still problem remains, then go for a soft reset ( it will not affect your data). for this type *#7780# in your keypad and provide security code (default 12345). check again..
if this post helped you, dont forget click on the white star
Or accept this as the solution
Nokia Asha Lover..... and Proud to be a Nokian
If this post helped you, don't forget!! click on the white star

ATAPI Devices - ATA/66 IDE Card OK?

I need to add a CD-RW, and with my HD, ZIP, DVD and DVD-RW, I need to add an IDE card. Do I need an ATA/100 card, or will an ATA/66 card suffice?

>> If you but a Zip Drive on the Ribbon with the Hard Drive you will force your ATA-100 Drive to run in ATA-33 Mode.
Forgot about that...thanks. So really the way to go is to have the HD As the Primary/Master off of the motherboard, with nothing else on it.
So now I have the Secondary IDE off the motherboard, and a new Primary and Secondary IDE channels on the ATA/66 card.
I'll have a DVD-ROM, DVD-RW, CD-RW and a Zip. What do you think is the best configuration with these resources? Are the DVD-ROM, DVD-RW and CD-RW all ATA/66 or ATA/33, or am I totally missing the ball here.
Thanks for the assistance

HT5622 last time i was in Saudi Arabia but now i am in Egypt i want to cahnge my region to add my new master card in Egypt but i can not .waht i do??

last time i was in Saudi Arabia but now i am in Egypt i want to cahnge my region to add my new master card in Egypt but i can not .waht i do??

Aqdas Hayat wrote:
.... Please I need a solution to this problem and would really appreciate the HELP.
The Device you have, because of where it was Purchased will never be able to have FaceTime.
All you can do is sell it and buy a Device from a non restrictive country.
FaceTime in the Middle East

Slow DVD Burning when using IDE card

I have a DVD burner plugged into an ide card and it only burns DVD-R at 2x. If I plug it straight into the board it burns at normal speed (12-16x). How do I configure the board to accept the ide card so that the drive burns at the proper speed?
During startup, raid detects the DVD drive model and indicates UltraDMA mode 4. For bios settings bus mastering is enabled and onboard ide is disabled. If I enable onboard IDE then the computer won't boot, so it is disabled. I am using dvd decrypter for burning and verbatim DVD-R's.
I will soon have 4 DVD burners all plugged into my 2 port raid card, so I can burn four discs at once. I will be burning hundreds of discs for a side job and need this to work asap. The IDE card is a Promose Ultra133 TX2. My board is the MSI K9N SLI Platinum and the burner Lite-On SOHW-1693S.

Quote from: Leroy_2000 on 13-November-07, 13:49:11
Hence what a forum is all about.
Sorry that I only now found this thread but glad to see you worked it all out. I have the same promise controller card laying in a drawer collecting dust right now for the same reason. I did get it to work but it was very unreliable on my K8N board. Because of this, I now only use 2 of my burners so that each can be a master connected to independent channels on the motherboard. I did away with all other IDE drives on this system and now have 4 SATA drives running happily. I may look into purchasing one of those controllers like yours, and reconfigure. I have having my 4 300GB PATA drives collecting dust.

Hard Disk Problems Detected

Hard Disk Problems Detected
A hard disk is reporting health problems.
I get this message. I have triple boot (Arch, Ubuntu & Windows) and I don't get any error messages on the other two OSs. The error is for my 1.0TB internal HDD and the SMART status is: DISK HAS MANY BAD SECTORS.
Any ideas on why I get that message or how to disable it?
Thanks in advance.

If your drive supports self-tests, perform a long one and review the results:
http://sourceforge.net/apps/trac/smartm … #Selftests
If the self-test doesn't confirm bad sectors you should do a system update with pacman.
Otherwise I'd prepare to back up my data.
Regards,
demian

Neo2 Platinum discovery - BIOSes above 1.5 don't like internal IDE cards

I upgraded my BIOS tonight from 1.5 to 1.B only to discover my system wouldn't boot. I thought it was a problem with my SATA drive, so I disconnected all my other drives, and it worked. Because I was having several other problems with this BIOS, even when it was working, I downgraded to 1.9, but the same thing happened: with all my hard drives connected, my system wouldn't boot into Windows. After the DMI prefetch check, it just sat there like a lame goose. I disconnected my hard drives one by one to see which was the culprit, only to discover that the two drives connected to my Promise internal ATA100 IDE card were causing the problem. If those two drives were not connected, the machine booted normally, but when they were connected, the machine hung at start up.
I proceeded to try this for 1.8 and 1.7 with the same results. Only 1.5 seemed to work with my IDE card. I switched around PCI slots, turned off my ethernet slots (I was intermittently getting a Realtek ethernet jack error, which would also prevent me from loading up. This even happened in 1.5, but disabling that got rid of the problem. I use wireless anyway.)
Anyone know why this is the case? I suppose that it is not inherently PCI IDE cards that the BIOSes don't like, but the existence of hard drives on external channels. Because if I disconnect the hard drives from the card, there is no problem, and the OS boots normally.
I have heard of one other person in this forum having this problem, but I don't have the luxury of plugging my extra hard drives in internally.
Thanks in advance for the help/experience.

Quote
Thanks for that guide :-) Found it
Changing the agp voltage to 1.60 (From 1.50) had no effect
The Os is reused (working correctly on any other p.c), any time I try to clean install a new Windows Xp I get "Files not found" errors when it comes to installing any software it extracted to my drive
So far as I know the Nvidia Ide sw driver is not loaded, however it's one of those things I wouldn't know where to look to check pre-os
Chnaging to LBA from auto had no effect on my problem
All in all this has me stumped
(Edit: Congratulations on hitting the big 5000 posts )
Sorry nothing seems to work . I'm stumped too since you have had this rig running .
If you have warranty still valid perhaps you should have the board replaced .
Didn't notice I rounded the 5K

I have a problem with Imac mid 2010 graphics card (ATI Radeon 5670 512MB)

I have a problem with Imac mid 2010 graphics card (ATI Radeon 5670 512MB). When I play video formats like xvid, mkv, avi iMac freezes and emits horrible sound,in service said the problem is not overheating. Not a problem with memory or hard disk because I placed second correct parts.The same problem is with OSX 10.6.8 and 10.8.4 and other players.Apple hardware test found no problem and tech tool pro found no fault.
After five days of testing in the service they can not found fault and it was decided to change the graphics card.
New graphics have been tested for two days but it is not reproduced divx ... but their test software which did not find any fault on the old graphics...
Do I have the right to complain if repair does not fix the problem because I use non apple softwere and video formats.

You could look at the System Profile for the info it presents for the card. But why wouldn't you think it's not up to date if you have the latest install (according to your sig above)?
What program are you trying to run? Is there anything in the system log?
I think it's the program that's having the problem and not anything with your video software.

When I print a photo to my epson printer, it comes out larger than the original photo - so the photo prints beyond the borders. Tried readjusting all sorts of things but nothing helps. I had this same problem with my Canon. any ideas?

When I print a photo to my epson printer, it comes out larger than the original photo - so the photo prints beyond the borders. Tried readjusting all sorts of things but nothing helps. I had this same problem with my Canon. any ideas?

Crop to the print size before pringing
LN

Is it possible to add a new graphics card to my macbook pro 2011 13"

Is it possible to add a new graphics card to my macbook pro 2011 13"?

Hi W,
Sorry, but no. It's soldered onto the logic board.

When I connect my iphone to my mac it says itunes will not work with my iphone cause it needs version 10.6.3 itunes,. problem is i have no idea how to down load that to my iphone when my mac will not connet to it cause it nees the down load help please

when I connect my iphone to my mac it says itunes will not work with my iphone cause it needs version 10.6.3 itunes,. problem is i have no idea how to down load that to my iphone when my mac will not connet to it cause it nees the down load help please

Ive got the same problem, just got my iphone unlocked, and they told me to sync it to itunes to get it permently unlocked, well everytime i plug my iphone in it says; it wont work as it needs up dating to 10.6.3, which i have already updated, but still doesnt work, so how can i get my phone unlocked?

Problem detecting: add-on Maxtor IDE card on Solaris 10.

Similar Messages

Maybe you are looking for