Problem Extending Linksys WRT54GS wireless with AEBS

Hello,
I know this post might seem redundant, but I really can't figure out what's wrong.
Here is my Configuration
Linksys Router :
WRT54GS v7 firmware :7.50.2
I tried the step-by-step instructions that i found here :
http://discussions.apple.com/thread.jspa?messageID=5338208
Same SSID
WPA for encryption, because I read somewhere that with the new firmware, it was accepted.
And what I get, is the following :
I have a steady Green light on the AEBS, when configure for WDS.
But as soon as I get the green light, my powerbook can't connect to the internet anymore via the AEBS, but if I turn the AEBS off, then I the airport of my powerbook switches back to the routeur wifi and I have internet again.
I'd really appreciate any input, even if it is to tell me that it is not possible to make it work.
Thanks

Yes, I understand what you are saying.
So you think that it should work, right ?
Doesn't the green light on the Airport tell me that the WDS settings are at least well configured ?
I guess what I don't really now how to set, is the internet tab, in the airport utility.
When I select using DHCP, it doesn't work : I don't get a green light.
When I select manually here are the setting I am putting :
IP adress : 192.168.1.130
Subnet Mask : 255.255.255.0
Router : 192.168.1.1
And I filled the DNS fields, with the same DNS present on the linksys page,
What should I do for the "Connexion Sharing" field ?
Thanks again

Similar Messages

Having trouble setting up a linksys WRT54GS router with v...

Having trouble setting up a linksys WRT54GS router with verizon DSL using a westell 6100F modem. the modem works fine by its self but the router will not connect to the internet when installed like the cd tells you to.
online help and phone help has been less than helpful, anyone have any Ideas?

Ok I found " Installing the liksys wireless router with a westell 6100 modem" in the verizon troubleshooting guides. printed the instructions so I would'nt forget. step 1 open your web browser and enter http://192.168.1.1 in the address field. PROBLEM it comes up with a login screen that I don't know how to sign into. tried the obvious stuff. cannot get past the login screen. I knew this sounded to easy to be true. anyone have any ideas?

Linksys WRT54G Wireless-G Router Not working

I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

I have a Linksys WRT54G wireless router that has a MAC address

A month ago, I could print from my PC and my Mac to my Epson printer over my Linksys WRT54G wireless network. Now, for some reason, I cannot connect and print from either computer. An Epson tech asked me to check the MAC address of the Mac and the printer to see if they were the same. They were not. He then opined that might be why I couldn't print.
I don't know what changed a month or so ago or why it changed. I have not done anything to change the MAC address on either the MAC or the printer.
The Epson guy said the problem might be fixed by adding my printer's MAC address to my router's MAC address. Something about "enabling MAC address filtering". Then he told me that was an issue to pursue with my router manufacturer. Naturally.
Speaking of that problem...someone else had it, too...another technician at another site wrote: "...by default, routers don't come with mac address filtering enabled...and if that's the case....then adding the printer's MAC will not solve any issue that you may be having..."
So, three qustions:
(1) Can I add my Epson Workforce 545 printer's MAC address to my Linksys router? Is that possible?
(2) If I can do it, how do I do it? I saw no "add" or "edit" functions on the Linksys WRT54G Status Page.
(3) What causes MAC address mismatching to happen? What is unstable in that assembly?
Solved!
Go to Solution.

Mac addresses with different devices will differ. No two devices will have the same mac address. this is also called the hardware address. This is designed so that it will serve as a unique identifier of your devices in the network which you can check thru the router. Now it is possible that wireless mac filter might be blocking it from connecting to the network. But it would be best to check as well and make sure that the printer is connected to your network and has the same ip address segment as your router.
How to check if mac filter is enabled:
Setting up wireless MAC Filtering to permit users to connect to the wireless network on your Linksys...
Setting up wireless MAC Filtering to prevent users from connecting to the wireless network on your L...

Problem Connecting Linksys WRT54G to Arris TM402P/100 Cable Modem

The Problem
Cannot get an internet connection attempting to install a Linksys WRT54G router between an Arris TM402P/100 cable modem and the local network.
Prior Configuration
Previously had DSL, with the Linksys WRT54G wireless router between the DSL modem and the local network, which worked perfectly.
New Configuration
This friend recently changed his broadband from DSL to Comcast cable, and he also has phone and television service over the same connection. The installation tech connected the cable modem directly to a desktop computer and left the Linksys router out.
The direct connection between the cable modem and the computer works fine, but he and his wife each have laptops and would like to us the Linksys router to connect wirelessly.
This is the TCP/IP configuration of the FAMILY workstation connected to Comcast
directly through Arris TM402P/110 cable modem:
Windows IP Configuration
       Host Name . . . . . . . . . . . . : family
       Primary Dns Suffix . . . . . :
       Node Type . . . . . . . . . . . . : Hybrid
       IP Routing Enabled. . . . . . : No
       WINS Proxy Enabled. . . .. : No
       DNS Suffix Search List. . .. : hsd1.wa.comcast.net.
Ethernet adapter Local Area Connection:
       Connection-specific DNS Suffix . : hsd1.wa.comcast.net.
       Description . . . . . . . ...... . . . : Intel(R) PRO/100 VE Network Connection
       Physical Address. . . . . . . . . : 00-11-11-6F-FB-69
       Dhcp Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
       IP Address. . . . . . . . . . . . : 67.185.155.0
       Subnet Mask . . . . . . . . . . . : 255.255.254.0
       Default Gateway . . . . . . . . . : 67.185.154.1
       DHCP Server . . . . . . . . . . . : 68.87.69.10
       DNS Servers . . . . . . . . . . . : 68.87.69.146
                                                    68.87.85.98
       Lease Obtained. . . . . . . . . : Tuesday, January 09, 2007 5:39:26 PM       Lease Expires . . . . . . . . . . : Friday, January 12, 2007 9:58:23 AM
I cannot find a configuration on the Linksys WRT54G that will allow me to connect to the internet through the Arris TM402P/110 modem. Have tried (1) setting the Linksys to use a dynamic WAN address, (2) setting the Linksys to static IP 67.185.155.0 with TCP/IP settings taken from the above configuration, (3) cloning the MAC address of the desktop computer's NIC and trying both (1) and (2) again.
The error message says that the network cable is not connected. Is it possible that the connection between the router and cable modem requires a cross-over cable?
Any suggestions?

on the router's ui... keep the internet type to dhcp....clone the mac address and then do a power cycle...ensure that the modem is completely powered off during the power cycle...if you have a battery back - up , remove the battery...after a minute , put back the battery and then plug in the power cable in the modem...
let me know if this helps you....

Trying to setup my Linksys WRT54G Wireless Router but having trouble.

Right, i will keep this nice and simple. I have had broadband internet for the past 10 days and yesterday i got myself a Linksys WRT54G Wireless router so both myself and my partner can connect our Macbook Pros up to the wireless internet.
But the problem is we cannot seem to connect onto the wireless network. It shows up when searching for internet connecting even when its is open without a password or with a password it does not want to connect?!?!
I can plug my laptop directly (as i am doing now) into the broadband modem and it works so i have no idea what is wrong? This afternoon we tried using a Windows Laptop and had the same problem. The wireless network shows up but when you enter the password that was entered on the 192.168.1.1 website it does not reconise it?!?!
If you can reply speaking English and not too much computer language that would be fantastic.
Many thanks

Hi candn14 and welcome to the forums!
Since internet connection is working fine on the laptop computer when plugged directly into the modem, you just need to configure your router settings.
Are you using a DSL or Cable connection? Please see the links below on how to configure your router with your internet provider (ISP).
Setting-Up a Router with Cable Internet Service
Setting-Up a Router with DSL Internet Service
Once you are finished doing so and your laptop is able to connect to the internet when connected to the modem > router > laptop, then you are now ready to configure the wireless settings of the router for you to be able to connect wirelessly.
Here are the steps:
Setting-Up the Wireless Settings on a Router
And please secure your network w/ a password.
Setting-Up Wireless Security on a Linksys Router
Please feel free to ask any questions again if you encounter any problems. Hope this helps.

Hi, I just bought a linksys WRT54G Wireless Router. My...

Hi,
I just bought a linksys WRT54G Wireless Router. My laptop was able to detect it wirelessly untill I changing the "Router Name" in the setup page(http://192.168.1.1)
While saving the settings, the wireless network suddently disconnected. From that point onwards, I was not able to detect the wireless network with any computer at all.
I tried unplugging it, resetting it, and even restory factory settings by holding the reset button for aprox 30 secs.
What is wrong?
Thanks in Advanced

Recheck the wireless setting (SSID, encryption, DHCP, etc) on router management page again. Also make sure your computer's wireless adapter setting matches the one you set on router.
picoHat
Home Network, Wireless Network and Computer Networking Made Easy

Persistent problems with Linksys WRT54GS Wireless Router

I'm currently running Vista with a Linksys WRT54GS router. As earlier discussed in this forum I am still having intermittent problems with the ATV taking down my network. Anyone else experienced this and come up with a sure fire fix?
When it's working I like the set up but I have to say, it is not nearly stable enough to be an everyday solution for getting my music and photos to my living room.
Thanks.

Hi, I am having the same problem -- my 2WIRE modem from AT&T recently blew up. So, I purchased the WRT54GS. As soon as I reconnected the AppleTV to the new router via a wireless connection, all of my machines (Mac and PC) lost their internet connections. I'm seriously considering going out and getting another 2WIRE.

HP Officejet Pro 8500 wireless Networking with LINKSYS WRT54GS wireless router

I have a HP Officejet Pro 8500 wireless printer conneted via WiFi to my LYNKSYS WRT54GS wireless router. I do not have a USB cable or ethernet cable plugged to the printer. I am able to use the 'scan to email button' and the 'scan to network folder' button on the front of the printer and I can pint from the PC to the printer with no problems.
I installed the HP printer software from the CD, choosing network/wireless connection, without having to install any USB cables from the PC to the printer in the process. many posts in the forum mention having to connect USB cables in the wireless installation process.
Can I install the software in the same fashion on the other two laptops? Or, do I need to do something differently?

The USB cable is used on those printers which do not have display or front panel wireless setup is not possible. We configure the wireless settings during install and save those settings in printer's memory by transferring through USB cable. Therefore the USB is plugged in during wireless installation temporarily. In your case I don't think plugging in USB cable is necessary as the printer is already on network and had IP address. Connect the laptops on wireless network and proceed with regular install, the printer should be detected automatically.
Thanks
Naveen K
HP Support Engineering Center
Click on BLACK STAR button to say thanks
(Although employed by HP, I'm trying to address the issues with my sole willingness and my employer does not bear any liability for my responses)

Linksys WRT54G compatible with XBOX 360's Wireless Network Adapter?

Is the Linksys Wireless G Broadband Router (WRT54G) compatible with XBOX 360's Wireless Network Adapter?

Use the LAN port and cable. That way you'll get no interference and great data transfer. Or this maybe helps. http://www.xbox.com/en-US/support/connecttolive/xbox360/homenetworking/equipment.htm
Message Edited by iknownothink on 06-21-2007 03:44 AM

Can't get AirPort Express to join LINKSYS WRT54G wireless network

After several unsuccessful attempts to follow Tesserax's advice to get my AX to join my LINKSYS wireless network, I depressed the reset button, plugged the AX in, and waited for the flashing reset confirmation. Reconfiguring from scratch to join my WPA network, all seemed to go well. After selecting to Update, the following window pops up:
<The settings for this AirPort Express have been successfully updated. You can close this window or wait for this AirPort Express to restart.
Waiting for the AirPort Express to restart…>
After a couple of minutes the following window appears:
<AirPort Utility was unable to find your AirPort Wireless device after restarting.
The settings for this AirPort wireless device have been successfully updated, but there was a problem re-joining the wireless network or finding the AirPort wireless device. You may need to select your network from the Wi-Fi menu and try again.>
At this point, AirPort Utility will no longer recognize the AX, no matter how many times I rescan. The only way I can get it to be recognized is to once again do a hard factory reset. I then go through the whole set up process again, only to end up in the same dead end. I'm thinking that there has to be some sort of problem between the AX and the LINKSYS. Prior to the above activity, I was able to send iTunes to the AX just fine. I just wasn't able to surf the Internet at the same time.
Any ideas you might have will be appreciated.

Thomas - I have a very similar problem - I've got a Wi-Fi/ADSL2 router supplied by my telecom company AirTel (the router's called 'beetel', 802.11g model) and I'm having problems extending it with Airport Express - the Airport Utility doesn't seem to be able to detect the AE after restart. The only difference with your case seems that you have a Linksys piece.
Here's what I tried:
1. Had my Wi-Fi network up & running with the beetel router (network name: PASTA)
2. Booted Airport Express
3. Launched Airport Utility 5.5.3 from Windows 7, detected the Airport Express, chose Manual Setup and went for option "Extend my Wireless Network" and chose PASTA and specified its password
3. Airport Utility restarted the device after saving changes, and Aiport Express went invisible.
That sounds like the same problem you had.
Just to cross check, I tried connecting an Ethernet cable between AE and the beetel router and went for option "Create Wireless Network" and that was a breeze.
@Tesserax - can Airport Express smoothly extend only an Airport Extreme WiFi network? Is there anything I can do to extend my current Wi-Fi network from this router?
Thanks for your notes & time
Forrest

Am I right in thinking that you can't extend your network wirelessly with a time capsule unless your base station is an apple one?

My new time capsule will only allow me to extend my network via ethernet cable.
What I really want to do is use it wirelessly as an extension wirelessly.
The option is there (under other options in airport utility) but when I select it and move on it reverts back to create a new network.
Why is this?
Am I trying to achieve the impossible?
I have an airport express and that be added to my network wirelessly with no issue at all.
Please help
Russell

Can I just "join" the network with my time capsule like I have with my airport express?
Apple does not present this option....but, even if they did.....this would be the worst possible option to use for backups.
Can I use my airport express as a base (connected via Ethernet to the router) for my time capsule to extend from wirelessly?
Yes, you can. The AirPort Express would be configured to "create a wireless network"......then.....the Time Capsule could be configured to "extend a wireless network".
It is critically important that the Time Capsule be located where it can receive a very strong wireless signal from the AirPort Express in this type of setup. The more that you have line-of-sight between the AirPort Express and Time Capsule, the better your network performance will be and the faster that backups will occur to the Time Capsule.
A better option in terms of performance would be to connect the Time Capsule to your current modem/router using an Ethernet connection and have the Time Capsule "create" the network. Then, use the Express to "extend" the network.
Here, I am assuming that you have a new Time Capsule.

Problem configure linksys rage expander with dlink router

Hi...I trait to configure my linksys rage expander with Dlink router, but it's impossible..beacuase ..when using the automatic configuration ..it not work fine and when use cd wizard setup..show the messages 'can't find any divice...
Could any help me...please..

What model and versions is the D-link and the WRE ? does your D-link router support WDS ( wireless distribution system ) The WRE will only work with routers that support WDS.

Linksys WRT54G interferance with Wireless Security

I searched the site and didn't see this type of problem, but I have a brand new WRT54GS with speedbooster. Setup and works great. Today I plugged in a Chamberlain wireless vehicle alert in my home, the result was my wireless internet connection was interupted. This required me to reset the router. Is there something I can do to prevent this so I can run both devices? Thanks for the help!!!!!

It looks like Chamberlain makes a few different models of their vehicle sensor. Which one do you use?
I found a user guide, but it did not say what radio frequency the device uses, and it did not mention anything about changing the channel.
Since you had a problem with your router, I would have to guess that the Chamberlain probably uses the same 2.4 GHz frequency band as your router. If this is the case, then the solution is to get the two devices to use different channels, and preferably 5 channels apart. There are 11 channels in the 2.4 GHz band, and the channels overlap one another. Usually channels 1, 6, and 11 work the best.
If you cannot change the channel that the Chamberlain is using, then change the channel in the router. In most cases, this should eliminate your problem.

Extend Linksys WRT160N wireless network with Airport Express

First off, I'm a network simpleton, so please keep that in mind!
I've seen similar posts, but I'm not sure definitively if this is possible. Trying to extend the wireless network from a linksys wrt160N with the airport. Is this possible without a phd in network engineering? If so, are there step by step instructions someplace that can help me?
I really appreciate any direction!

Welcome to the discussions!
I'm assuming that you are trying to do this using wireless only.
Apple's "extend a wireless network" feature will only work if both the main router and extending device are Apple "n" devices. Unfortunately, this feature is not compatible with devices from other manufacturers.

Problem Extending Linksys WRT54GS wireless with AEBS

Similar Messages

Maybe you are looking for