Problem in 3750 with multiple IP segment in same VLAN

Hi,
I've problems in 3750 and would like to ask for help.
I've 3750 switch with standard image. Because of lacking IP addresses, I'm going to redesign the IP scheme. Before complete migrate to new IP range, I've to let new IP segment co-exist with old IP segment for a while (I've 3 VLANs that have same situation). For example, 10.10.13.0/24 (old) will co-exist with 10.10.32.0/21 (new) in same VLAN (let say VLAN 32).
Below is the partial configuration in 3750:
interface VLAN 32
ip address 10.10.13.2 255.255.255.0 secondary
ip address 10.10.32.2 255.255.248.0
standby 14 ip 10.10.13.3
standby 40 ip 10.10.32.3
I've two PCs. PC-A is 10.10.13.250 and PC-B is 10.10.33.250, both are using HSRP IP as default gateway (the subnet mask are correct).
My problem is:
Two PCs can not ping to each other. I can not ping to both PCs from 3750. But if I'm using physical IP as their gateway (such as 10.2.13.2 for PC-A and 10.2.32.2 for PC-B), then both PCs can be ping each others.
How can I solve the problems if I've to use HSRP IP as default gateway?

I don't get it. What is the significance of standby 1 and 2 VS standby 14 and 40? The only difference I noticed is the lower number of standby group goes with primry and higher goes with secondary.
If possible, can you also try the same config you used before except swapping the group number?
e.g.
interface VLAN 32
ip address 10.10.13.2 255.255.255.0 secondary
ip address 10.10.32.2 255.255.248.0
standby 40 ip 10.10.13.3
standby 14 ip 10.10.32.3

Similar Messages

Problem Creating PDF with Multiple Files in Pro. 7

I'm using Adobe Acrobat Professional 7 on a computer with Windows XP.
The problem is that when I try to create a PDF with multiple files everything just suddenly stops. There are 75 files involved and when it gets to around 41 or so (don't know the exact number because I turned away from my computer for just a moment), it just stops. There are no error messages; nothing. Just a blank Acrobat screen.
Last week I had a different problem which was resolved by an uninstall/reinstall and I was able to create the PDF with those exact same 75 files, but after the PDF was created I realised that some changes needed to be made. I dumped the PDF, made the appropriate changes and left it for the weekend. Today I the new problem has arisen.
Any ideas what the problem might be?

I've read many discussions about Acrobat and problems with server files, with the general solution being what you are doing... copy the files to a local hard drive

Problem when working with multiple sequences

Dears,
In order to make life easier (I am currently working on a rather long project), I work with multiple sequences, one per chapter.
My problem: I named one sequence "assembly sequences" in order to add the various sequences. I dropped the sequence no 1, then no 2. All works fine, beside that when playing the sequence no 2, I see two black lines on top and bottom of the screen for the all length of the sequence. Which is not the case when I click on the sequence itself and play it independently.
Any idea how to solve this ?
Thanks
Nic

Thanks, what happened is that :
1st sequence is like this : Frame size 720x576 pixels, video rate 25fps, Compressor DV-Pal. And I think it is the one appropriate for me and my country.
2nd sequence is like this : Frame size 720x480 pixels,
video rate 29.97 fps, Compressor DV-DVPRO-NTSC.
I think I should change the second sequence setting, but can I do it after all the work I have done, and continue making a 3rd, 4th and so on ?
Tx for your precious help,
Nicolas

Problem initiating process with multiple operations using HTTP/SOAP

Hi,
I have defined a process which has multiple operations. My process starts with a pick activity containing onMessage branches for each possible operation. When I initiate this service using the BPEL console, I choose one of the operations and everything works fine.
However, when I initiate this process using an HTTP/SOAP web service call using JMeter, always the first branch is executed regardless of the message I send.
My operations are document/literal. Due to some restrictions, I cannot define a SOAPAction for the operations. Could this be the problem? Is there a workaround for this? If this is not the problem, what could be the cause?
I'm using version 10.1.2.1.
Any help will be appreciated. Thanks in advance..

hi i am using 10.1.3 and still i can not initiate a process with multiple operations. Is there anybody to tell if pick activity works fine and if there are some points to consider?
If there is a problem is there any solution to make a process with multiple operations?

I'm having problems in a GOOP application with multiple instances of the same object running simultaneously.

I?ve written an application to control a system with multiple lamps. Each lamp in the system has its own power supply. Each lamp object contains a reference to its power supply. The application contains an array with the references to all the lamps in the system. Each lamp is in charge of monitoring itself and setting its power supply?s voltage according to the applications commands, therefore each lamp needs that its ?run me? method will run as long as the application is running i.e. the run method has to be reentrant. Because there are multiple lamps and because the ?run me? methods for each lamp run simultaneously, to over come this problem each lamp has a met
hod ?run? that calls ?run me? with ?RUN VI? invoke node with the ?Wait until done? set to false. When I run the application, it seems to work but if I check the AO there is no change in the output, and the lamps seem to be reading their input from the same channel. I can?t seem to find the problem, I think that the fact that the method is reentrant causes some sort of mix-up in the separate object references. Also because the method is reentrant I can?t debug it (with one lamp it seems to work ok). Does anyone have any idea what could be causing this problem.
P.S I'm having problems attaching my sample program to this message. You can contact me at [email protected] to recive the sample program I wrote.

Jean, Thanks for your answer, I've tried checking the invoke node that calls the "Run VI" method but it doesnt return an error any of the times its called even that the Vi that it called is still running. I also tried your solution of changing the object's "Run" method to a template but that doesnt work either. I can't seem to post the sample progam that demonstrates the problem, is it possible to send it to you by email, contact me at [email protected]
Attachments:
Sample_program.zip ‏926 KB

Firefox opens new tabs automatically, so i end up with multiple tabs of the same site. it's like it is consistantly trying to restore my last session.

Firefox keeps reloading tabs from my recent history over and over. So i might end up with multiple tabs of Pandora, Google home page or other sites I go to all the time-all running at the same time . rebooting does not help.

It is possible that there is a problem with the files sessionstore.js and sessionstore.bak in the Firefox Profile Folder.
Delete the files sessionstore.js [2] and sessionstore.bak in the Firefox Profile Folder.
* Help > Troubleshooting Information > Profile Directory: Open Containing Folder
* http://kb.mozillazine.org/Profile_folder_-_Firefox
If you see files sessionstore-##.js with a number in the left part of the name like sessionstore-1.js then delete those as well.<br />
Deleting sessionstore.js will cause App Tabs and Tab Groups and open and closed (undo) tabs to get lost, so you will have to create them again (make a note or bookmark them).
See also:
* [1] http://kb.mozillazine.org/Session_Restore
* [2] http://kb.mozillazine.org/sessionstore.js

Lightroom CC issues with multiple export at the same time

Back before Lightroom updated to the CC version, I was able to use export presets to send 4 different versions of the photos I'm working on at the same time (A Full Size for client at certain size, full size for myself, web-sized with watermark and a thumbnail). Since updating to the CC version, I'm only able to start the export process on two of these versions before the system simply becomes crippled and I cannot even navigate through Lightroom without it chugging along.
For reference, I'm running a 2014 rMBP with 16GB of RAM, LR is the only app open at the time and it's showing that I have roughly 6GB of RAM free when attempting this export.
TL;DR: LR5 worked wiht multiple exports at the same time, but LRCC now chugs after 2 exports are started

Re: "Selecting video in Messages, now starts Face time for video. Face time is one to one only."
Apple "Messages" supports two different types of video conferencing. It's become more than a little confusing. If you (or the person on the other end) ONLY have accounts set up for Apple's "iMessage" service (associated with your Apple ID and "iCloud") you may see the video symbol, but when you click on it you will be connected via FaceTime which is limited a 1-to-1 video conference.
However, if you have set up an AIM account in Messages (you may already have an AIM account ID if you once used iChat for video, audio and screensharing) and the person at the other end also has an AIM account you will be connected via AIM and will be able to do screen sharing and multi-person video conferences just like the old iChat, i.e. you'll have iChat Theater features, up to 4-way conferencing, etc.
It can get very confusing if, for example, you've signed up for AIM using a .me or .cloud email address. But once you have it set up and learn to recognise the way Messages switches between AIM and iMessage all the old iChat features work just fine in Messages.

How can I create a hashmap() with multiple values for the same key?

I am trying to write an application that will us something like a Map() with multiple values but some have the same key. Is this possible?

i had the same question. just create a List, add all the values u want to it, and then put the List into the map like u would a normal single value. e.g.
List list = new ArrayList();
list.add(value1);
list.add(value2);
map.put(key, list);
i bet u r doing the same course as i am =)

Timesten replication with multiple interfaces sharing the same hostname

Hi,
we have in our environment two Sun T2000 nodes, running SunOS 5.10 and hosting a TT server currently in Release 7.0.5.9.0, replicated between each other.
I would like to have some more information on the behavior of the replication w.r.t. network reliability when using two interfaces associated to the same hostname, the one used to define the replication element.
To make an example we have our nodes sharing this common /etc/hosts elements:
151.98.227.5 TBMAS10df2 TBMAS10df2-10 TBMAS10df2-ttrep
151.98.226.5 TBMAS10df2 TBMAS10df2-01 TBMAS10df2-ttrep
151.98.227.4 TBMAS9df1 TBMAS9df1-10 TBMAS9df1-ttrep
151.98.226.4 TBMAS9df1 TBMAS9df1-01 TBMAS9df1-ttrep
with the following element defined for replication:
ALTER REPLICATION REPLSCHEME
ADD ELEMENT HDF_GNP_CDPN_1 TABLE HDF_GNP_CDPN
CHECK CONFLICTS BY ROW TIMESTAMP
COLUMN ConflictResTimeStamp
REPORT TO '/sn/sps/HDF620/datamodel/tt41dataConflict.rpt'
MASTER tt41data ON "TBMAS9df1-ttrep"
SUBSCRIBER tt41data ON "TBMAS10df2-ttrep"
RETURN RECEIPT BY REQUEST
ADD ELEMENT HDF_GNP_CDPN_2 TABLE HDF_GNP_CDPN
CHECK CONFLICTS BY ROW TIMESTAMP
COLUMN ConflictResTimeStamp
REPORT TO '/sn/sps/HDF620/datamodel/tt41dataConflict.rpt'
MASTER tt41data ON "TBMAS10df2-ttrep"
SUBSCRIBER tt41data ON "TBMAS9df1-ttrep"
RETURN RECEIPT BY REQUEST;
On this subject moving from 6.0.x to 7.0.x there has been some changes I would like to better understand.
6.0.x reported in the documentation for Unix systems:
If a host contains multiple network interfaces (with different IP addresses),
TimesTen replication tries to connect to the IP addresses in the same order as
returned by the gethostbyname call. It will try to connect using the first address;
if a connection cannot be established, it tries the remaining addresses in order
until a connection is established.
Now On Solaris I don't know how to let gethostbyname return more than one interface (the documention notes at this point:
If you have multiple network interface cards (NICs), be sure that “multi
on” is specified in the /etc/host.conf file. Otherwise, gethostbyname will not
return multiple addresses).
But I understand this could be valid for Linux based systems not for Solaris.
Now if I properly understand the above, how was the 6.0.x able to realize the first interface in the list (using the same -ttrep hostname) was down and use the other, if gethostbyname was reporting only a single entry ?
Once upgraded to 7.0.x we realized the ADD ROUTE option was added to teach TT how to use different interfaces associated to the same hostname. In our environment we did not include this clause, but still the replication was working fine regardless of which interface we were bringing down.
My both questions in the end lead to the same doubt on which is the algorithm used by TT to reach the replicated node w.r.t. entries in the /etc/hosts.
Looking at the nodes I can see that by default both routes are being used:
TBMAS10df2:/-# netstat -an|grep "151.98.227."
151.98.225.104.45312 151.98.227.4.14000 1049792 0 1049800 0 ESTABLISHED
151.98.227.5.14005 151.98.227.4.47307 1049792 0 1049800 0 ESTABLISHED
151.98.227.5.14005 151.98.227.4.48230 1049792 0 1049800 0 ESTABLISHED
151.98.227.5.46050 151.98.227.4.14005 1049792 0 1049800 0 ESTABLISHED
TBMAS10df2:/-# netstat -an|grep "151.98.226."
151.98.226.5.14000 151.98.226.4.47699 1049792 0 1049800 0 ESTABLISHED
151.98.226.5.14005 151.98.226.4.47308 1049792 0 1049800 0 ESTABLISHED
151.98.226.5.44949 151.98.226.4.14005 1049792 0 1049800 0 ESTABLISHED
Tried to trace with ttTraceMon but once I brought down one of the interfaces did not see any reaction on either node, if you have some info it would be really appreciated !
Cheers,
Mike

Hi Chris,
Thanks for the reply, I have few more queries on this.
1.Using the ROUTE CLAUSE we can use multiple IPs using priority level set, so that if highest priority level set in thr ROUTE clause for the IP is not active it will fall back to the next level priority 2 set IP. But cant we use ROUTE clause to use the multiple route IPs for replication simultaneously?
2. can we execute multiple schema for the same DSN and replication scheme but with different replication route IPs?
for example:
At present on my system, I have a replication scheme running for a specific DSN with stand alone Master-Subscriber mechanism, with a specific route IP through VLAN-xxx for replication.
Now I want to create and start another replication scheme for the same DSN and replication mechanism with a different VLAN-yyy route IP to be used for replication in parallel to the existing replication scheme. without making any changes to the pre-existing replication scheme.
for the above scenarios, will there be any specific changes respective to the different replication schema mechanism ie., Active Standby and Standalone Master Subscriber mechanism etc.,
If so what are the steps. like how we need to change the existing schema?
Thanks In advance.
Naveen

Active active with multiple csm in the same 6500

How can I achieve active/active configuration with csm in a 6500? Can I do it with 2 csm in the same chassis or I need two chassis, each with one csm?

you can't have active-active setup with CSM.
The CSM uses only 1 FT group and all vservers are linked to it.
So once CSM is active and the other one standby.
If the FT group fails on the active, the standby takes over and it takes a full control - not partial as needed for active-active.
It does not matter if you have 1 chassis or more.
The new ACE module offers the possibility to do active-active.
Gilles.

Problem with multiple threads accessing the same Image

I'm trying to draw into one Image from multiple threads. It works fine for a while, but then suddenly, the image stops updating. Threads are still running but the image won't update. I'm using doublebuffering and threads are simply drawing counters into Image with different speed.
It seems like the Image gets deadlocked or something. Anyone have any idea what's behind this behavior or perhaps better solution to do such thing.
Any help will be appreciated.

Sorry Kglad, I didn't mean to be rude. With "No coding
errors" I meant the animation itself runs with no errors. I'm sure
you could run the 20 instances with no freezing (that's why I put
the post :) ) But I'm affraid it is an animation for a client, so I
cannot distribute the code.
Perhaps I didnt explain the situation clearly enough (in part
because of my poor english...).-
- By 20 instances I mean 20 separated embedded objects in the
html
- The animation is relatively simple. A turned on candle, in
each cycle I calculate the next position of the flame (that
oscilates from left to right). The flame is composed by 4
concentric gradients. There is NO loops, only an 'onEnterFrame'
function refreshing the flame each time.
- It's true that I got plenty variables at the _root level.
If that could be the problem, how can I workaround it?
- It is my first time trying to embed so many objects at the
same time too. No idea if the problem could be the way I embed the
object from the html :(
- The only thing I can guess is that when a cycle of one of
the object is running, the other 19 objects must wait their turn.
That would explain why the more instances I run, the worst results
I get. In that case, I wonder if there's a way to run them in a
kind of asynchronous mode, just guessing...
Any other comment would be appreciated. Anyway, thanks a lot
everybody for your colaboration.

Problem in Aggregate with Multiple level of dimension

Hi,
I have a BI repository with a snowflake schema. I have also designed the business model with snowflake, It works with drilling and all but I am facing problem when I am
creating a logical column aggregating with a higher level of dimentation. Let me illustrate that :
I have the Following Hierarchy :
Tournament(id, Name) ---- > Round (id, name, tournament_id) -------> Match (id, Name, RoundId ) | Match is fact table and other 2 dimension.
I also created a logical dimension called tournament with 3 levels.
Now say I want to create a logical column Total Number of Matches , aggregating to the dimension level of Tournament. The result gives counts a 0 for every tournament. However
it is working perfectly when the dimension level is Round (which is the immediate next level after fact).
The Logical request generated (in case of Tournament level) :
   MatchId:[DAggr(Measure1.MATCHID by [ Matches$.TournamentId] SB Tournament)] as c1 GB.
    There is no such column as TournamentId in Matches$ table. How does the BI server got this ?
   The execution plan evaluate this:
     cast(NULL as INTEGER ) as c1 GB [for database 0:0,1]
   Can someone please explain why is this happening, is it because of the snowflake schema, but I guess if BI server can handle a snowflake schema it should work the Aggregate
   properly in multiple levels of dimensions, or it is something I am doing wrong.
   Execution Environment:
     Windows XP , OBI 10g on OC4J. Data source : MS Excel (ODBC 3.5)
Regards,
Ru

Hi,
With reference to your question.
Can any operator perform this task..I don't think any single operator will help you.
I suggest using an intermediate (staging) table by using a PL SQL procedure with output port to store the values of account number provided the number of accounts are limited. Else use an array variable for account of an employee.
In short no simple solution because of the bad source design else the pivot/unpivot operator would have helped you.
Cheers
- Mohammed

Problem in mapping with multiple values

Hi all,
I am facing a problem during mapping. I am explainning the problem with a example.
Suppose i have a source table named Employee which has two columns emp no and account no. I have a target table Emp_account which has also the same columns.
One employee may have more than one accounts. In source table this account nos are stored in account no column in one row corresponding to emp no. The multiple values in account no are separated by comma for one record in source table.
But in the target table Emp_account a single record will be inserted for each employee's separate account. There should not be multiple values separated by comma in account no column of target table.
So if any employee has two accounts this will be stored as one row in source table but in target table it will divided into two different rows for each account.
EMPLOYEE(Source)
emp no account no
10 101, 102
EMP_ACCOUNT(Target)
emp no account no
10 101
10 102
Think I explained the requirement.. How can i made this in OWB mapping editor..Is it possible?...Can any operator perform this task...If any of u know about this plzz give some solution..It's very important ..
Thanks & Regards,
Sumanta Das

Hi,
With reference to your question.
Can any operator perform this task..I don't think any single operator will help you.
I suggest using an intermediate (staging) table by using a PL SQL procedure with output port to store the values of account number provided the number of accounts are limited. Else use an array variable for account of an employee.
In short no simple solution because of the bad source design else the pivot/unpivot operator would have helped you.
Cheers
- Mohammed

Problem socket.bind() with multiple modems and multiple IPs

I've connected 2 or more modems in Windows control panel and made up windows dail ups. Then I dail up each modem and obtain the local DHCP IPs of each modem.
My target is : to set up sockets using separate modems.
the code is like: create a socket instance , and use Socket.bind()method to bind the socket to a specified modem's local IP , then do socket.connect().
but the problem is : although there are several modem dail ups and at the same time I bind each socket to different IPs , the program always connect via the first modem dailed up.
Does Socket.bind() method really bind the socket connection to the IP's or hardwares?

I think you are trying to use a Socket where you want a ServerSocket to accept the incoming connection. Check this out (I have underlined what
should interest you):
public ServerSocket(int port, int queueLength) throws IOException, BindException
This constructor creates a ServerSocket on the specified port with a queue length of your choosing. If the machine has multiple network interfaces or IP addresses, then it listens on this port on all those interfaces and IP addresses. The queueLength argument sets the length of the queue for incoming connection requests--that is, how many incoming connections can be stored at one time before the host starts refusing connections. Some operating systems have a maximum queue length, typically five. If you try to expand the queue past that maximum number, the maximum queue length is used instead. If you pass 0 for the port number, the system selects an available port.
For example, to create a server socket on port 5,776 that would hold up to 100 incoming connection requests in the queue, you would write:
try {
ServerSocket httpd = new ServerSocket(5776, 100);
catch (IOException e) {
System.err.println(e);
}The constructor throws an IOException (specifically, a BindException) if the socket cannot be created and bound to the requested port. An IOException when creating a ServerSocket almost always means one of two things. Either the specified port is already in use, or you do not have root privileges on Unix and you're trying to connect to a port from 1 to 1,023.
So once you receive a connection, it looks like it is up to you parse any
relevant info you want out of the Socket you get from ServerSocket.accept();
-Cludge

Problem importing PSD (with multiple groups and layers) into After Effects. Help!

I created a "comic strip" in photoshop (multiple rectangle shape layers, then various shapes within each box for each frame of the comic strip) that I want to import into AE. When I import it as a composition (to keep my layers), however, what appears is an simply a black image with white lines where the lines of the comic strip used to be. I checked the color modes, but they are both in RGB so I don't think that's the problem. Also, when I double click the cartoon strip composition, I can choose certain groups from the mini flow-chart at the top left and view those individual frames. However, I can't view the entire comic strip as a whole, which is necessary for my animation. Any help with this would be greatly appreciated, as I'm on a tight time constraint. Thanks!

When I asked what version down to the last decimal, I meant it. After Effects version should start with 11, but we need the numbers after that too.
And I understand that you want to pan between them, so just put all the different PSD's you import into the same comp and pan between them.

Problem in 3750 with multiple IP segment in same VLAN

Similar Messages

Maybe you are looking for