Problem in APD creation from BW to CRM

Hi all,
I want to create apd which would feed data from BW to CRM. For that I have gone through a post in scn where it was told to create project and then extension in crm side (eewb transaction). I did all but in the wizard where I have to create table, I was unable to approach forward because of some issues.
1) It gives an error message that key is not selected, although I have selected the key.
2) Some other time it gives error that infoofject cannot be validated, although the infoobjects are activated in bw side.
Please help me in this regard.
Thanks and regards,
Sumit

Hi Vimal,
You'd need to debug the FM CRM_BUPA_MAIN_VAL to find out what was the cause of validation error. Once you get the missing details, check if those details are being populated correctly at ECC end.
Thanks,
Rohit

Similar Messages

Problem in data transfer from BW to CRM

Dear Guys,
I am facing one problem when i am tranfering the data from BW to CRM system (using Analysis Process Designer).
When i am transfering data from standard ODS, data has changed properly.
But in custom ODS, data has not changed.
In both part, upto aggregation data has come.
Any thing i have missed out in custom ODS.
Please anybody give inputs.......
Thanks in advance.
Regards,
Vivek.V

Hi Vivek,
There is no special process for this cube load. Just check the job log and check for any short dump in R/3 while running the extractor.
I checked the datasource help link for this cube but there is nothing special mentioned:
http://help.sap.com/saphelp_nw04/helpdata/en/da/f7bc3961d4f339e10000000a114084/content.htm
Bye
Dinesh

Problem in delta changes from ECC to CRM for Customers created in CRM systm

Dear all,
I am replicating customers between CRM and ECC and vice versa. The Delta changes are replicating from CRM to ECC system, but not happening from ECC to CRM system.
I have created some customers in CRM system and changed some address data, those changes are perfectly updating in back end ECC system.
But when I make some changes for the same customer from ECC system, those changes are not updating back in the CRM system.
I could not get the problem where exactly is coming. I request your expertise to help me in resolving this issue. I believe all middleware and pide settings are correct.
Your suggestions are highly appreciated.
Best regards
Raghu ram

Hi Shanthala,
Thank you very much for your prompt response, I have checked Customer_main adapter object in R3AC1, no filter has been found there.
and in R3 table TBE31, I could not find entry for CRS_CUSTOMER_COLLECT_DATA for APPLK = BC-MID.
As well in CRMRFCPAR table I could see X assigned to field named with 'In Queue Flag', but I could not find DISCARDDAT for CRM (User) settings.
Kinldy help me to resolve the issue.
Your suggestions will be highly appreciated.
Best regards
Raghu ram

Urgent text shifting problem with pdf creation from indesign

I have eps files placed in indesign and when some pages of my document are exported as pdf for press, the text moves slightly, like 1/16" or less, but enough to cause problems. I'm using the original Indesign CS and eps files saved out of Illustrator 10. Yup, old.....I know, but it's what I have to work with right now. Some files are working fine but others are don't and they were all created/saved/exported the same, as far as I can tell. Here's a small sample. All the street name text is shifted down and to the left from the actually street. Occurring with text on path as well as straight text. Any ideas greatly appreciated.

You might also try exporting to .idml form CS5 (see Remove minor corruption by exporting). We've had other reports of similar beahvior when working with legacy files, and exporting to .inx from the original version may work even better.

Problem in customer replication from ECC to CRM

Hi experts,
When I create a customer in ECC using Tcode XD01 a BDOC is created in CRM. But this Bdoc shows following errors:--
     Partner (): the following errors occurred
     Incorrect input data:
     Validation error occurred: Module CRM_BUPA_MAIN_VAL, BDoc type BUPA_MAIN.
When I see the Bdoc message body the data(central data etc )is all blank except the field Object = BUSINESSPARTNER.
Why the Bdoc messae is not getting populated with correct value?
Also how I can see the data which is being sent from ECC. Is there any Idoc or something created at ECC outbound side where I can see the sent data?
Where in XD01 bdoc message is being created?
Please help.
Regards,
Vimal

Hi Vimal,
You'd need to debug the FM CRM_BUPA_MAIN_VAL to find out what was the cause of validation error. Once you get the missing details, check if those details are being populated correctly at ECC end.
Thanks,
Rohit

Replicating BPs from ECC to CRM- Error IN SMQ2 as Stop.

Hello Gurus,
I am facing problem in replicating BPs from ECC to CRM. After initial load , when monitoring the In bound Q in transaction SMQ2 it is showing status as Stop.
Kindly let me the possible solution to remove the status.
Cheers
Prashant Ranalkar

Hi,
If you double-click on the queue that is in stop status (so, step one when you have your list of queues, double-click on the one that is in error state, this will give you a one-line entry, then double-click this one line again, and it will give you a detailed view of what is held within that queue), it will give you more information and may have a line in it that is causing the error. This tends to give you more info on why it is in stop status (we have had wide, varied and some weird ones in here!) - most of the time you fix it by just deleting that line that has the error associated with it. then you just go back one level to the queue 'header' and click on the unlock queue button and it should process.
Hope this helps
Regards
Cara

Auto PO creation from PR through ME58 problem.

Hi experts.
We are providing facility to our client auto po creation from PR through Me58 transaction code.
I am facing amazing problem is that it is working fine in development client , not working in Quality and Production client , exactly problem is that ME58 u2013 Ordering Assigned Purchase requisition & Process Assignment Create PO , Purchase order cannot be created, PR shift in document overview , it means user want to drag and drop in purchase order then system create PO , this problem I am facing in Quality & Production , but it is working fine in development server there is no need to drag and drop , immediately after Process assignment Create PO , system directly convert PR into PO just only need to check and save PO. I compare everything with development & quality data including material master , source list and everything still I am unable to understand where is the problem , is there any customization settings related to auto po ? pls. suggest any solution to solve this issue.
Kumar

Hi,
Config setting.
Settings for Automatic PO creation is:
1. Select the Automatic PO check box/option in Purchasing view of material master
2. Select the Automatic PO option in the purchasing data view of Vendor master
3. Maintain Purchase info record
4. ME56- Assign the vendors to PR's
5. ME58- Create PO via assignment list(PR-> PO)
6. ME57- Assign and process PR's
7. ME59N - Create PO automatically via PR
Above step by step procedure is involved in the Automatic PO creation.
SAM

APD process is active, How to trigger the data from BI to CRM table

Hi All,
I want to send data from BI system(using APD method) to CRM table (ADS method).
I am able to see the table for e.g ABCD in CRM system , i can open using SE11 , but data is 0.
In BI , i have data in DSO and i have mapped it in APD process to data Target to CRM system and APD is active.
Now i want to know how to trigger the data from BI to CRM table? (e.g ABCD).
Please let me know the steps.
Regards.
Nithi.

Hi
Just create a Process Chain to execute this APD method, if the process Chain is already available, then just insert this Process in to the process Chain and execute the Process Chain by normal process, by hoe we do in general.
Hope it solves...

Creation of support message from Webserver like CRM, XI

Hi Gurus,
Can anyone guide me, how to Create support message from Webserver like CRM, XI.
I could configure from GUI Based systems like ECC, SCM.
But i don't know how to configure for CRM, XI etc..,Java based web applications.
Pls guide me.

try maybe using the web interface service desk application. the same one that you find in the incident management workcenter when you choose New Message.

Unable to open URL attachment from SBWP in CRM WEB UI

Hello Gurus,
Need your help please. I'm having some problem opening the URL attachment from SBWP via CRM 7 WEB UI (I used a Transaction Launcher for SBWP). The attachment is a Webdynpro application. I am able to open the attachment in SAP GUI, but not in CRM WEBUI. This problem occured when we update the SP level of CRM 7.
Here's the scenario,
- whenever I click the attachment, it open a new window, which also happen even before SP level update, with the following information:
Execute an Application on FrontEnd
Please wait. You will be forwarded automatically.
This page is included for technical reason.
Execute program.
Status: Displaying Office Document ..........
After a couple of seconds, it will return to the Workflow Workplace screen.
I have checked the workflow log and found no inconsistency on the attached URL.
Immediate response would be highly appreciated. Thanks in advance.
Regards,
Edwin

Thanks for the reply WD ABAP.
Yes, I did try to use the functionality of Worklist and the URL attachment successfully opened. However, there are some limitation in its functionality as indicated in the link below that opted us to use the SBWP in CRM WEB UI via transaction launcher.
http://wiki.sdn.sap.com/wiki/display/CRM/CRMWorklist-AdvancewithDialognotSupported
We don't want to adjust the logic of our existing workflow at this point as described in the above link as it will entails end-to-end testing again. We just encountered this issue when we update the SP level of CRM 7.
Hope there is an alternative solution without shifting us to Worklist.
Regards,
Edwin

Problem establishing SSL VPN from only 1 IP address

Hi,
I'm experiencing strange problem.
I can't establish SSL VPN connection from 1 IP address, but I don't have problem establishing SSL VPN from any other IP address.
Remote IP address: 10.0.0.1
ASA's public IP address: 192.168.1.1
Output of packet-tracer:
1. with problematic source IP address:
packet-tracer input wan tcp 10.0.0.1 50601 192.168.1.1 443 detailed
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   192.168.1.1   255.255.255.255 identity
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff37573f00, priority=119, domain=permit, deny=false
        hits=861, user_data=0x0, cs_id=0x0, flags=0x0, protocol=6
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=443, dscp=0x0
        input_ifc=wan, output_ifc=identity
Phase: 3
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff38a10a50, priority=8, domain=conn-set, deny=false
        hits=4069, user_data=0x7fff38770910, cs_id=0x0, reverse, flags=0x0, protocol=6
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
        input_ifc=wan, output_ifc=identity
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff395c7d70, priority=0, domain=inspect-ip-options, deny=true
        hits=4044934, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
        input_ifc=wan, output_ifc=any
Phase: 5
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff37560700, priority=13, domain=ipsec-tunnel-flow, deny=true
        hits=2268518, user_data=0x0, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
        input_ifc=wan, output_ifc=any
Phase: 6
Type: TCP-MODULE
Subtype: webvpn
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff38a10cc0, priority=13, domain=soft-np-tcp-module, deny=false
        hits=4627, user_data=0x7fff38c14300, cs_id=0x0, reverse, flags=0x0, protocol=6
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
        input_ifc=wan, output_ifc=identity
Phase: 7
Type: VPN
Subtype: encrypt
Result: DROP
Config:
Additional Information:
Reverse Flow based lookup yields rule:
out id=0x7fff375504a0, priority=69, domain=encrypt, deny=false
        hits=40747, user_data=0x0, cs_id=0x7fff3754fa40, reverse, flags=0x0, protocol=0
        src ip/id=192.168.1.1, mask=255.255.255.255, port=0
        dst ip/id=10.0.0.1, mask=255.255.255.255, port=0, dscp=0x0
        input_ifc=any, output_ifc=wan
Result:
input-interface: wan
input-status: up
input-line-status: up
output-interface: NP Identity Ifc
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
If I run packet-tracer with any other source IP address, let's say 10.0.0.2, everything is OK:
packet-tracer input wan tcp 10.0.0.2 50601 192.168.1.1 443 de
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   192.168.1.1   255.255.255.255 identity
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff37573f00, priority=119, domain=permit, deny=false
        hits=862, user_data=0x0, cs_id=0x0, flags=0x0, protocol=6
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=443, dscp=0x0
        input_ifc=wan, output_ifc=identity
Phase: 3
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff38a10a50, priority=8, domain=conn-set, deny=false
        hits=4090, user_data=0x7fff38770910, cs_id=0x0, reverse, flags=0x0, protocol=6
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
        input_ifc=wan, output_ifc=identity
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff395c7d70, priority=0, domain=inspect-ip-options, deny=true
        hits=4047886, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
        input_ifc=wan, output_ifc=any
Phase: 5
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff37560700, priority=13, domain=ipsec-tunnel-flow, deny=true
        hits=2270040, user_data=0x0, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
        input_ifc=wan, output_ifc=any
Phase: 6
Type: TCP-MODULE
Subtype: webvpn
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fff38a10cc0, priority=13, domain=soft-np-tcp-module, deny=false
        hits=4648, user_data=0x7fff38c14300, cs_id=0x0, reverse, flags=0x0, protocol=6
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
        input_ifc=wan, output_ifc=identity
Phase: 7
Type: USER-STATISTICS
Subtype: user-statistics
Result: ALLOW
Config:
Additional Information:
Reverse Flow based lookup yields rule:
out id=0x7fff3a1cc320, priority=0, domain=user-statistics, deny=false
        hits=4902651, user_data=0x7fff3a0043c0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
        input_ifc=any, output_ifc=wan
Phase: 8
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 4384689, packet dispatched to next module
Module information for forward flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_tcp_normalizer
snp_fp_tcp_mod
snp_fp_adjacency
snp_fp_fragment
snp_fp_drop
Module information for reverse flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_tcp_normalizer
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Result:
input-interface: wan
input-status: up
input-line-status: up
output-interface: NP Identity Ifc
output-status: up
output-line-status: up
Action: allow
I run packet capture on WAN interface - and I can only see incoming packets (SYN) with destination to tcp/443 but there isn't any outgoing packet (SYN/ACK).
I even can't open web page from internet browser (url https://192.168.1.1) when source IP is 10.0.0.1, but I can open "SSL VPN Service" web page from any other source IP address.
The only thing different with this IP address is that there's configured site-to-site (IPsec) vpn tunnel from same source to same destination IP address.
Here is the configuration of the tunnel:
group-policy GroupPolicy_10.0.0.1 internal
group-policy GroupPolicy_10.0.0.1 attributes
vpn-filter value VPN-ACL
vpn-tunnel-protocol ikev1 ssl-client
access-list VPN-ACL:
access-list VPN-ACL extended permit ip object-group DM_INLINE_NETWORK_83 object-group DM_INLINE_NETWORK_84
object-group network DM_INLINE_NETWORK_83
network-object 10.11.217.0 255.255.255.0
network-object 192.168.201.0 255.255.255.0
object-group network DM_INLINE_NETWORK_84
network-object 10.11.217.0 255.255.255.0
network-object 192.168.201.0 255.255.255.0
tunnel local & remote networks:
access-list wan_cryptomap_5 extended permit ip 10.11.217.0 255.255.255.0 192.168.201.0 255.255.255.0
crypto map wan_map 5 match address wan_cryptomap_5
crypto map wan_map 5 set connection-type answer-only
crypto map wan_map 5 set peer 10.0.0.1
crypto map wan_map 5 set ikev1 transform-set ESP-3DES-SHA
I've configured the same setup in my lab and I can't reproduce the error.
The SW version running on ASA is asa861-12.
I'm out of ideas.

Just collected some other information:
1. traceroute shows that traffic is not leaving ASA at all
1   * * *
2   * * *
3   * * *
I double checked that there is no "strange" entry for remote public IP in routing. Traffic with destination to remote IP should be sent via default gateway like all other traffic.
2. debug crypto ipsec shows this information when I ping public IP address of the remote host (with VPN
IPSEC(crypto_map_check)-3: Looking for crypto map matching 5-tuple: Prot=1, saddr=192.168.1.1, sport=30647, daddr=10.0.0.1, dport=30647
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 1: skipping because 5-tuple does not match ACL wan_cryptomap_1.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 2: skipping because 5-tuple does not match ACL wan_cryptomap_2.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 3: skipping because 5-tuple does not match ACL wan_cryptomap_3.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 4: skipping because 5-tuple does not match ACL wan_cryptomap_4.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 5: skipping dormant map.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 5: skipping dormant map.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 6: skipping because 5-tuple does not match ACL wan_cryptomap_6.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 7: skipping because 5-tuple does not match ACL wan_cryptomap_7.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 8: skipping because 5-tuple does not match ACL wan_cryptomap_8.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 9: skipping because 5-tuple does not match ACL wan_cryptomap_9.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 10: skipping because 5-tuple does not match ACL wan_cryptomap_10.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 11: skipping because 5-tuple does not match ACL wan_cryptomap_11.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 13: skipping because 5-tuple does not match ACL wan_cryptomap_13.
IPSEC(crypto_map_check)-5: Checking crypto map wan_map 65535: skipping dynamic_link.
IPSEC(crypto_map_check)-1: Error: No crypto map matched.
It really seems that the whole problem is that ASA is trying to encrypt traffic sent from public IP address of one VPN endpoint and targeted to public IP address of another VPN endpoint and send it to remote VPN endpoint via IPcec tunel.
There is indeed VPN tunnel established between both VPN endpoints, but there are just local and remote networks defined with private IP address space for this tunnel, VPN endpoint's public IP addresses are not included in the definition of this IPsec VPN tunnel.
And there are at least two more IPsec VPN tunnels configured the same way and I can't reprodure this error on there two VPN tunnels.
Any idea?

Replication of Quotations from ECC to CRM

Hello Experts,
The scenario is as follows:
I am required to replicate all the quotations from ECC to CRM.
My question is: what are the various middleware settings to be done?
I have created a transaction type for quotation by the same name in ECC and CRM so far.
It would be great if I can get help on the following:
1. What are the item categories that I need to maintain on both ECC and CRM side for Quotation?
2.What action profile do I need to maintain on ECC and CRM side for quotation?
3.How should the number ranges be defined on ECC and CRM side for quotation?
4. Do I need to do a Cross-Copy Control of quotation from ECC and CRM at the transaction and item category level?
5. Do I need to assign the Quotation Type (ECC) to ERP Profile on CRM side?
6.Can the transfer of quotations from ECC to CRM happen only after replicating the product and customer data from ECC to CRM?
What more needs to be done?
Once the settings are complete and fool-proof, I know I can run an Initial Load (R3AS) on the object: SALESDOCUMENT from R/3 to CRM.
What are the filter settings to be maintained in SalesDocument Object?
Experts, this is my requirement and all the pointers would be greatly helpful.
Many thanks,
VSK.
Edited by: venkatskumar on Feb 16, 2011 12:17 AM

Hello
Please find below my reply :-
1. What are the item categories that I need to maintain on both ECC and CRM side for Quotation?
>> You can make a Z copy of the standard Quotation Item categories in ECC and CRM.
2.What action profile do I need to maintain on ECC and CRM side for quotation?
>> Action profile settings are specific to your business scenario. You need to define ACTION Profile in ECC. In CRM you can have an ACTION PROFILE and assign it to the CRM Transaction Type
3.How should the number ranges be defined on ECC and CRM side for quotation?
>> If ECC is a leading system for quotation creation, the number range will be EXTERNAL in CRM and assign this EXTERNAL number range for CRM Quotation Transaction Type
4. Do I need to do a Cross-Copy Control of quotation from ECC and CRM at the transaction and item category level?
>> Yes
5. Do I need to assign the Quotation Type (ECC) to ERP Profile on CRM side?
>> Not sure on this. Requesting other experts to answer this.
6.Can the transfer of quotations from ECC to CRM happen only after replicating the product and customer data from ECC to CRM?
>> Yes. The master data such as Material, Customer, Pricing should be downloaded to CRM, if the quotation needs to be replicated to CRM.
Hope this will be helpful.
Regards

Replication of CUSTOMER from ECC to CRM

Hi CRM Guru
Is that anyway to download the partner function (sold-to, ship-to, payer, bill-to, employee) in the customer sales area data from ECC to CRM (created as BP relationship in CRM) in the INITIAL LOAD?
For example:
Customer in ECC 100000000 have the partner function in the partner function tab under the sales area data
SP Sold-to = 100000000
SH Ship-to = 100000001
PY Payer = 100000002
BP Bill-to =100000003
And create those relationship in CRM under the Relationship area.
Please advice.
Thank you

Hi.
If what you are trying is to replicate the partner functions as relationships, first be sure that you have replicate the customer (the main and the others on partner functions sales areadata) using the middleware object CUSTOMER_MAIN.
Then run the object CUSTOMER_REL for the main partner. This will result on the relationship creation at CRM side, representing the partner functions on R/3 site.
Be aware that if in R/3, the main partner represents all the partner functions, when it is replicated into CRM, the system does note create a relationship to himself, but this not means that the partner can be used in sold to party, payer, ship to and bill to partner functions on documents.
Regards.
SM

Replication of bp name field from ERP to CRM

Hi experts,
We have a problem in ERP to CRM master data replication.
We have already connected our ERP (ECC 5.0) system to CRM 7.0.
We have made initial master business partners (bp) data load from ERP to CRM without problems.
All bp fields, including NAME (but000-name_org1) are transfered correct from ERP (KNA1-NAME1) to CRM.
We have a z program in ERP that is used by users to change the customers names (KNA1-name1).
When we use our custom program in ERP to change the kna1-name1 field in ERP, the bp name field is not changes in CRM.
Using XD02 or FD02 in ERP to change the name (kna1-name1) field in ERP the replication of this field to CRM is correct.
KNA1 table is updated correctly in ERP using our custom program .
What does transactions XD02 and FD02 has that make name filed replicated in CRM?
Thanks in advanced.

Hi,
First variant:
You have to retry load business partners by request:
Tcode R3AR4, R3AR2, R3AR3
So, system retrive new data from tables and transfer to CRM.
Second variant:
You have to add to your z-program part, there you fill data in the CRM system also (via RFC).
Denis.

Problem regarding the creation of Table using CSS.

Hi ,
Here I have a Problem regarding the creation of Table using CSS.
In My Application i have a table with multiple rows(Rows are Dynamically added to the table).First i am setting the table with the following properties:
width:900px;
height : auto,
Overflow : visible,
Max-height: : 200px.
If I use above properties,I'm getting a table with 5 or 6 rows(height upto 200px).After that i am getting the Vertical ScrollBar.
The problem is when a table has many columns, Vertical and Horizontal Scrolls are coming at the time of setting the table. The table height is not Increasing dynamically.
How can i use "height" property in CSS? (I want the table height to be increased when the columns are more.)
Thanks & Regards
Madhavi

Hey humble user. Errr I'm trying to understand what ur trying to do. U want to create a section of a region destructively from an existing region right? If so select the option convert to new region (opt-comm-R or selecting it by right clicking). Check your audio bin to make sure. Whats the "merge" function? Are u refering to the glue tool?

Problem in APD creation from BW to CRM

Similar Messages

Maybe you are looking for