Problem in RFC sender and receiver

Hi,
I my one scenario, I am using Rfc As a sender, every day program ID is getting unregistered.
Another problem is with RFC receiver, there Rfc connection is not getting closed automatically so, every time for new Rfc connection,  I need to increase the maximum connection limit.
Please help me in this.
Thanks

Hi Joel,
This can happen if application in which program ID has been define is getting restart everyday.
-Pinkle

Similar Messages

  • Problem with Send and Receive Emal In SAP System

    Hi gurus!
    I have a following quote:
    Dear !
    I have a problem with send and receive email in SAP system following :
    I want to test send and receive email in local network at my company. I
    had two server
    Server 1 : I setup Exchange Mail Server 2007 with domain controller is
    fes.com
    Server 2 : I setup SAP ERP ECC 6.0
    On Server 1 : I created 2 account ( u1Afes.com and u2Afes.com ) and then I tested send and receive email between u1 and u2 in local network through Microsoft Outlook 2007 -> OK
    and then
    On Server 2: I had configured send and receive email on SAP system
    through tcode SBWP, SCOT and SOST as Note 455140 - "Configuration of
    e-mail, fax, paging or SMS using SMTP"
    for example :
    I logged in SAP system with user Basis01 (with email u1Afes.com ) -> then,using tcode SBWP -> new message -> send to u2Afes.com with Internet Mail type and then status message with green light -> sending ok
    and then I have used Microsoft Outlook 2007, I logged with account u2 ->check email -> Ok. I saw message which send from u1
    Finally, My problem is how can receive mail in SAP system without using Microsoft Outlook
    For example:
    Login system SAP with Basis01 account (with  u1Afes.com ) -> tcode SBWP ->New Message -> send to u2Afes.com
    and then
    Login system SAP with Basis02 account (with u2Afes.com ) -> tcode ??? ->
    To receive email from Basis01 (with u1Afes.com )
    Please help me now
    Thanks
    I replace "@" with "A" because of banning email of this forum.
    This quote is about sending email in local network. And we can't receive any email from the outside email address. Addition if I wanna send email to internal email in Internet (we've just tried with email address in local network) What should I config in SAP and Exchange ?
    By the way, Is SAP Server IP added to Relay Agent for sending or receiving mail ?
    Regards
    An NLP
    Edited by: An NLP on Apr 6, 2010 7:03 PM

    Hi,
    This problem is a classic problem of mail routing via Exchange. Exchange like most mail servers use the domain part of the email address as a means to route mails. So I will make an assumption that your main company mail addrss is "User @ fes.com".
    So when you send a mail to the "User @ fes.com mail" address the mail is delivered to your Outlook mail address as this is the default route for company.
    (Q) So how do you get your Exchange server to relay the mail into the sending SAP system?
    (A) The easiest way would be to setup and unique mail domain for your SAP system. I always recommend "user @ client.sid.company.com" which in your case would be "u1 @ 100.PRD.fes.com". You can then instruct Exchange to send any emails addressed to 100.PRD.fes.com domain to your SAP system. Also using this format of address you can configure multiple mail connections into multiple SAP systems.
    (A) Another answer would be to enter the "Full" email address (LOcal and Domain part of address) into the routing rule for Exchange e.g. "U1 @ fes.com" so that all emails addressed to this user will be delivered into SAP. However this method requires a lot of Admin as you will have to update Exchange with ALL email address that need to receive emails. Also if your corporate mail address is "U1 @ fes.com" then all mails will be forwarded to SAP.
    I would definitely NOT recommend this method but the decision is up to you.
    P.S. The IP address of the SAP system is entered into the mail header of the email. This is standard practice in SMTP relay. You can suppress this header in Exchange
    Hope this helps
    Michael

  • Problem with sending and receiving e-mail through exchange [GMail]

    Hello I have problem with sending and receiving e-mail.
    all is well set, username and password are correct, the server set m.google.com. verification of data is about like stepping into a post and want to check the post office gives me an error message: Can not Get Mail. The connection to the server has failed
    I have this problem on my two iPhone

    http://www.zdnet.com/google-drops-exchange-activesync-support-for-free-email-acc ounts-7000008836/

  • HT4628 I am able to download updates and send and receive email so I know I have connection to my wireless router. However, when I click on Safari, I get the message "Safari quit unexpectedly." What is my problem and how do I solve?

    When I click on Safari, I get the message "Safari quit unexpectedly." I know I have access to my wireless net work because I just found and downloaded updates and can send and receive mail. What is my problem and hoe is it solved?

    As Outlook is not an Apple product, you will find more helpers familiar with Outlook here:
    Office for Mac forums

  • I have a new iPhone 6 plus and all is OK. But the mail shows more than 400 'unread' messages whereas there are none in the mailbox or trash or anywhere else I have looked. I can send and receive with no problem. I'm sure I have no unread messages.

    I have a new iPhone 6 plus and all is OK. But the mail shows more than 400 'unread' messages whereas there are none in the mailbox or trash or anywhere else I have looked. I can send and receive with no problem. I'm sure I have no unread messages.

        jsavage9621,
    It pains me to hear about your experience with the Home Phone Connect.  This device usually works seamlessly and is a great alternative to a landline phone.  It sounds like we've done our fair share of work on your account here.  I'm going to go ahead and send you a Private Message so that we can access your account and review any open tickets for you.  I look forward to speaking with you.
    TrevorC_VZW
    Follow us on Twitter @VZWSupport

  • Problem with Stored Procedure exection in Sender and Receiver side of JDBC

    Hi All,
    I am facing problem while executing Stored Procedures using sender and receiver sides of JDBC adapter.
    Here is my SP in Oracle DB :
    PROCEDURE EMP                           
    ( ID IN VARCHAR2,NAME IN VARCHAR2,PROCESSED IN VARCHAR2  ) AS                                                          
    BEGIN                                                         
       INSERT INTO EMPLOYEE VALUES (ID, NAME, PROCESSED);COMMIT;END EMP;
    Now I want to execute this SP using sender JDBC channel and receiver JDBC channel.
    Can anyone please help me executing this SP?
    Regards,
    Soorya

    Hi Soorya,
    The receiver Data type should be like this:
    <StatementName>
    <storedProcedureName action=u201D EXECUTEu201D>
        <table>realStoredProcedureeName</table>
    <param1 [isInput=u201Dtrueu201D] [isOutput=true] type=SQLDatatype>val1</param1>
    </storedProcedureName >
      </StatementName>
    Check the link http://help.sap.com/saphelp_nw04/helpdata/en/64/ce4e886334ec4ea7c2712e11cc567c/frameset.htm
    Which DB  are you using?? The sender structure will be like
    <resultset>
    <row>
    <field1></field1>
    <field2></field2>
    <field3></ field3>
    </row>
    </resultset>
    Search SDN you will get lot of examples
    Regards
    Suraj

  • Hello! Im having problems about my Iphone showing NO SERVICE on top. Im not able to send and receive msg, same with calls

    Hello Guys! I hope someone could help me, Im having trouble with my phone's signal, I am not able to send and receive msgs, same as make calls and receive calls. At first, my phone is working fine (iphone 4, iOS 7.0.4) and all of a sudden, my text messages are not getting through, and I noticed that my phone shows NO SERVICE, I refreshed the phone by turning it off and turning it on after a couple of minutes, it worked. My phone is okay again after that, Im able to send and receive messages again. But after few hours, the problem came again. NO SERVICE sign is displayed again, but this time after refreshing the phone nothing good happened. I tried almost every possible thing I can to fix it but it doesn't work. What should I do.
    Thank you

    Hey Clara,
    These are the recommended troubleshooting steps to resolve No Service issues on iPhone:
    Toggle airplane mode: Tap Settings > Enable Airplane Mode, wait five seconds, then turn off airplane mode.
    Turn iPhone off and then on again.
    Remove the SIM card and verify that it's a valid, carrier-manufactured SIM. Also verify that it isn't damaged, worn, or modified. Then reinsert it.
    Check for a carrier-settings update. Connect to a Wi-Fi network. Then tap Settings > General > About. If an update is available, iOS will ask you if you want to install it. If Wi-Fi isn't available, connect your device to iTunes.
    Update your iPhone to the latest version of iOS.
    Reset network settings by tapping Settings > General > Reset > Reset Network Settings. This will reset all network settings, including Bluetooth pairing records, Wi-Fi passwords, VPN, and APN settings.
    Restore the iPhone.
    If you are outside the United States, please also follow these steps:
    Go to Settings > Carrier > Automatic.
    If the phone registers any carrier network, Settings > Carrier will be present.
    If the Carrier option is missing in Settings and you are outside of the Unites States, please contact Apple for support and service options.
    Set the option for Automatic to off.
    A list of potentially available carriers appears after about two minutes. If the device is locked to a carrier, it may connect only to the carrier network to which it is locked. If the device displays carrier networks, then the device is working as expected.
    Set Settings > Carrier > Automatic back to on.
    If you're still experiencing No Service issues, contact your carrier to check for any network or account issues that could cause these symptoms.
    from: iPhone: Troubleshooting No Service
    http://support.apple.com/kb/TS4429
    Welcome to Apple Support Communities!
    Take care,
    Delgadoh

  • RFC Sender and RFC Receiver Sync Scenario . Help required.

    Hi,
    I need to make RFC Sender and RFC Receiver Sync Scenario.
    Any docs/links for it.
    Regards

    Hi,
    I have CRM (r/3) and DM (r/3)system.
    Data from differnent tables of CRM system needs to go to
    DM system different tables , data will be saved there and then return response back to CRM system.
    For this I have given one RFC for CRM system
    For this I have given one RFC for DM system
    So I have to make Sync Outbound Interface
    and Sync Inbound Interface.
    So I think so no BPM is required.I am correct?
    Adapter -- RFC Sender and RFC Receiver Adapter.
    Regards
    Edited by: Henry H on Jan 29, 2008 11:20 AM

  • My iphone 4 did not make call. It can receive calls, send and receive sms, internet is working. How can I solve this problem?

    My iphone 4 did not make calls but I receive calls, send and receive sms, emails, etc. How may I solve it?

    I am having the same problem with ios 4.3.5

  • Another send and receive problem

    We have three accounts setup on our iMac. Mine, my wife, and our children.
    My account and the kids have no problem sending or recieving email. But my wife can only send and receive emails hit and miss. We are all using the same pop account, so I have those setting correct. Some times she gets the prompt asking to retry send. Some times it just takes them off line.
    Any ideas?

    The easiest fix would be to just use safari and a webmail interface.
    For example, I have yahoo in my mail app. But on some internet connections it just won't work, so I use safari to get to yahoo.com and access my mail that way.
    Your mail provider should have a web interface and you could use that.

  • TS3276 I have no sound on my MacBook Air for sending and receiving messages. All sound settings have been checked and are OK. This problem has arisen many times and is intermittent in the sense that the sound returns and disappears for no apparent reason.

    I have no sound on my MacBook Air for sending and receiving messages. All sound settings have been checked and are OK. This problem has arisen many times and is intermittent in the sense that the sound returns and disappears for no apparent reason.

    Open System Preferences > Sound > Sound Effects
    Select:  Play user interface sound effects
    And make sure the Mute box is not selected.
    Now open Mail. From the Mail menu bar clik Mail > Preferences then select the General tab.
    Make a selection from the:  New messages sound  pop up menu.

  • Mail (5.3) OS X 10.7.5 mail program crashing when opening an email with attachment. Any suggestions out there? I can open the mail program...send and receive emails...click on emails without attachments with no problem.

    I am having a problem successfully opening an email containing attachment. I can open the mail program...send and receive emails...and view emails that do not contain attachments. But whenever I click on an email containing an attachment, I get the spinning beach ball for a few seconds and then the entire program closes. Any suggestions before I make a one hour trip to the Apple store for help?

    I don't think an interactive portion of a PDF is an obscure problem (lots of designers I know use rollable PDF files for emailing 3D models) and while I understand that it's in a legacy program, there is no guarantee if I purchase Acrobat X, that the same problem won't exist. It's no an issue in Reader 10 but then again, it wasn't an issue in Reader 9 either. Since Adobe doesn't give trial versions for Mac (stupid), I have no way of checking this. The problem doesn't annoy me as much as being an Adobe product user who upgraded only to not have functionality and not have a way to have it resolved.

  • Problem I-message? I can't send and receive the messages.

    from last Sunday I have a problem with I-message. It's impossible to send and receive the messages. what's the problem?

    I assume you have tried all of the troubleshooting here?
    iOS: Troubleshooting Messages
    It would also help to head to Settings -> General -> Date & Time and make sure it is set to Automatic.  You could also try using Google's DNS servers as doing so has resolved the issue for a number of users.  Head to Settings -> Wi-Fi and tap the > next to the network you are connected to.  Scroll down to the DNS fields and enter in8.8.8.8and 8.8.4.4.
    B-rock

  • I changed my carrier , i can't send and receive any sms any call, i erase my data and after the problem still..ifone 4S ios 8.3..thank u

    iPhone 4S 16 Gb
    iOS 8.3
    I change my carrier , I can't send and receive any sms any call
    I erase my data .,after the problem still again
    can you help me please ?
    thank u

    thank u
    but when I make my sim card in another phone it work normaly.and when I make another sim card in my fone the problem still and I can't send
    have you another solutions ?

  • Apple Mail send and receive problems, Network Solutions

    Hello Everyone,
    I'm currently facing a problem with a company email account that we have with network solutions.
    NSmail Pro (IMAP) that is configured with apple mail. Here are the settings that i have:
    Incoming mail: mail.(company.domain).com
    Port: 110
    SSL: No
    Outgoing mail: smtp.(company.domain).com
    Port: 2525
    SSL: No
    Auth: Password
    Whenever i'm at the office, I can send and receive emails without any problems (Using mail app), but when i'm at home i can't receive emails nor send one.
    I'm wondering if this has something to do with the Mail application, cause i can access the email using the webmail on a browser without any problems (either at home or at the Office).
    Any thoughts from our experts?

    I'm guessing that when you are at the office, you are probably accessing a company network and the company mail will only work with those settings on the company network. You may need to discuss this with your IT department at work to see if it need a different configuration for outside access.
    The fact that it works at work and not at home indicates a that it surely an issue with the connection setup.
    Assuming that you are accessing it through wi-Fi at both locations, do you have different wi-Fi connections set up on you Mac in Network Preferences, or is it the same wi-Fi connection used for both? In other words, do you have a specific wifi setup on your computer for connecting at the office?

Maybe you are looking for