Problem in signal Q 10

I am facing a problem, all the time my Q 10 is searching for signal, no network.
I appreciate your support.
Regards;

Maybe a silly question, but do you know if the provider you are with supports your area?
Could you try a new SIM, maybe a friends or colleagues?
If it still is not working then the phone probably has a fault.
If you've been helped click on , if you've been saved buy the app.
Developer of stokLocker, Sympatico and Super Sentences.

Similar Messages

My iphone 5 has a problem with signal

My iphone 5 has a problem with signal, it always search for network. I had removed and plug sim card again but it doesn't work. Then I restore the iphone, and an exception was throw "... An unknown error has occured (3)."

unknow error 3 means the computer has lost communication with the device during the restore. It can be anything from bad cable, USB port, phone hardware etc.
Since your phone had a signal issue before, it would be your baseband chip faulty and when the restore tries to connect with the baseband chip to check (it does this when you restore) it waits till the chip responds then times out when it doesnt get any response. The restore will try this several times then eventually restart the phone to get out of the loop. As the phone gets restarted (or shutting off) itunes think the phone turned off and throws error 3.
Go to apple if it's under warranty. If not try to find where they do chip replacement as this is not something that you can do yourself.

Migrating E&M immediate start from 2821 VGW to AS5350XM but problems with signalling

Hi,
We currently have 2821 VGW platforms running E&M Immediate start. The T1s go into the DACS and the IP interface connects to the SIP server with a simple number plan.
So, when a T1 DS0 signals, the VGW talks to the SIP server, the SIP server does a database lookup and talks back to the VGW and passes the connection details.
However we are now migrating to the AS5350XM platform and replicating the config from the 2821 to the AS5350XM is causing signalling issues.
Here is a sample of the existing 2821 config:
voice rtp send-recv
voice service pots
voice service voip
sip
bind control source-interface GigabitEthernet0/0
bind media source-interface GigabitEthernet0/0
rel1xx disable
min-se 1700
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
controller T1 1/0
ds0-group 0 timeslots 1 type e&m-immediate-start
ds0-group 1 timeslots 2 type e&m-immediate-start
ds0-group 2 timeslots 3 type e&m-immediate-start
voice-port 1/0:0
define Tx-bits idle 1111
define Tx-bits seize 0000
define Rx-bits idle 1111
define Rx-bits seize 0000
timeouts wait-release 1
connection plar 1000
voice-port 1/0:1
define Tx-bits idle 1111
define Tx-bits seize 0000
define Rx-bits idle 1111
define Rx-bits seize 0000
timeouts wait-release 1
connection plar 1001
voice-port 1/0:2
define Tx-bits idle 1111
define Tx-bits seize 0000
define Rx-bits idle 1111
define Rx-bits seize 0000
timeouts wait-release 1
connection plar 1002
dial-peer voice 1000 pots
destination-pattern 1000
port 1/0:0
dial-peer voice 1001 pots
destination-pattern 1001
port 1/0:1
dial-peer voice 1002 pots
destination-pattern 1002
port 1/0:2
dial-peer voice 1 voip
preference 1
destination-pattern .T
session protocol sipv2
session target ipv4:192.168.150.2:5060
session transport udp
voice-class codec 1
voice-class sip options-keepalive retry 1
sip-ua
retry invite 2
timers trying 150
sip-server ipv4:192.168.150.2:5060
Here is the same on on the AS5350xm:
voice rtp send-recv
voice service pots
voice service voip
sip
bind control source-interface GigabitEthernet0/0
bind media source-interface GigabitEthernet0/0
rel1xx disable
min-se 1700 session-expires 1700
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
controller T1 3/0:1
framing ESF
ds0-group 0 timeslots 1 type e&m-immediate-start
ds0-group 1 timeslots 2 type e&m-immediate-start
ds0-group 2 timeslots 3 type e&m-immediate-start
cas-custom 0
define-abcd loop-open 1 1 1 1
define-abcd loop-closure 0 0 0 0
cas-custom 1
define-abcd loop-open 1 1 1 1
define-abcd loop-closure 0 0 0 0
cas-custom 2
define-abcd loop-open 1 1 1 1
define-abcd loop-closure 0 0 0 0
voice-port 3/0:1:0
timeouts wait-release 1
connection plar 1000
voice-port 3/0:1:1
timeouts wait-release 1
connection plar 1001
voice-port 3/0:1:2
timeouts wait-release 1
connection plar 1002
dial-peer voice 1000 pots
destination-pattern 1000
port 3/0:1:0
dial-peer voice 1001 pots
destination-pattern 1001
port 3/0:1:1
dial-peer voice 1002 pots
destination-pattern 1002
port 3/0:1:2
dial-peer voice 1 voip
preference 1
destination-pattern .T
session protocol sipv2
session target ipv4:192.168.150.2:5060
session transport udp
voice-class codec 1
voice-class sip options-keepalive retry 1
sip-ua
retry invite 2
timers trying 150
sip-server ipv4:192.168.150.2:5060
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
What I did notice was the following:
1) When defining loop open and loop closed custom bit configuration is different....on the 2821 you do it on the voice port. On the AS5350, it is not supported on the voice port but appears to be configurable via the T1 controller. I'm not sure if the AS5350 needs any further E&M signalling configuration as the problem lies in the signalling....the AS5350 when the line is cleared down appears to start ringing it again and not following the signalling pattern.
2) When doing a "show voice port" on the AS5350XM does not show E&M signalling, whereas it does on the 2821:
AS5350XM:
5350VGW#sh voice port
DS0 Group 3/0:1:0 - 3/0:1:0
Type of VoicePort is CAS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 1000
Initial Time Out is set to 15 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 1 s
Spe country is not configured
Region Tone is set for US
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
DS0 channel specific status info:
                                      IN      OUT
PORT            CH SIG-TYPE    OPER STATUS   STATUS    TIP     RING
=============== == ============ ==== ======   ======    ===     ====
2821:
2821VGW#sh voice port
recEive and transMit Slot is 0, Subslot is 0, Sub-unit is 0, Port is 0
Type of VoicePort is E&M
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 1000
Initial Time Out is set to 15 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 1 s
Companding Type is u-law
Rx A bit no conditioning set
Rx B bit no conditioning set
Rx C bit no conditioning set
Rx D bit no conditioning set
Tx A bit no conditioning set
Tx B bit no conditioning set
Tx C bit no conditioning set
Tx D bit no conditioning set
Rx Seize ABCD bits = 0000 Custom pattern
Rx Idle ABCD bits = 1111 Custom pattern
Tx Seize ABCD bits = 0000 Custom pattern
Tx Idle ABCD bits = 1111 Custom pattern
Ignored Rx ABCD bits = BCD
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
Voice card specific Info Follows:
Operation Type is 2-wire
E&M Type is 1
Signal Type is immediate
Dial Out Type is dtmf
In Seizure is inactive
Out Seizure is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Clear Wait Duration Timing is set to 400 ms
Wink Wait Duration Timing is set to 200 ms
Wait Wink Duration Timing is set to 550 ms
Wink Duration Timing is set to 200 ms
Minimum received Wink Duration Timing is set to 140 ms
Maximun received Wink Duration Timing is set to 290 ms
Minimum seizure Timing is set to 50 ms
Delay Start Timing is set to 300 ms
Delay Duration Timing is set to 2000 ms
Dial Pulse Min. Delay is set to 140 ms
Percent Break of Pulse is 60 percent
Auto Cut-through is disabled
Dialout Delay is 300 ms
Hookflash-in Timing is set to 480 ms
Hookflash-out Timing is set to 400 ms
DS0 channel specific status info:
                                      IN      OUT
PORT            CH SIG-TYPE    OPER STATUS   STATUS    TIP     RING
=============== == ============ ==== ======   ======    ===     ====
0/0/0:0          01 e&m-imd     dorm idle     idle
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Can anyone advise if further configuration is required on the AS5350XM in order to pass the E&M signalling correctly ?

Well for me the forms were ok to open with 11g, just had to correct differences and recompile to run.
That there script is a ton of help!..well you forgot to mention the Output_File parameter, but I could find that myself now that I knew what to look at. Now if I could also set it not to produce .err files when everything went fine and to set the output names so that the old compiled forms get overwritten..
the SRW.* calls turned out to be things used in Reports, so it was hopeless to compile in forms..but also not needed
as for ENABLE_ITEM and DISABLE_ITEM I found these to use as their definitions in a library, that proved sufficient.
procedure enable_item
( p_menuName in varchar2
, p_menuItemName in varchar2
) is
v_menuItem menuitem;
begin
v_menuItem := find_menu_item(p_menuName||'.'||
p_menuItemName);
if (not id_null(v_menuItem))
and (get_menu_item_property(v_menuItem,visible) = 'TRUE')
then
set_menu_item_property(v_menuItem, enabled, property_true);
end if;
end;
procedure disable_item
( p_menuName in varchar2
, p_menuItemName in varchar2
) is
v_menuItem menuitem;
begin
v_menuItem := find_menu_item(p_menuName||'.'||
p_menuItemName);
if (not id_null(v_menuItem))
and (get_menu_item_property(v_menuItem,visible) = 'TRUE')
then
set_menu_item_property(v_menuItem, enabled, property_false);
end if;
end;Some forms still playing with me, but the compilation issues there don't seem to be connected with this topic..and now I got issues with reports >.< but that requires a topic elsewhere. Thanks all!

Export to Excel problem in Signal Express 2012

Equipment used: PXIE-8102 CELERON T3100 1.9GHZ Controller Windows 7, PXIE-1071 4 Slot Chassis, PXIE-4140 4-Channel SMU 1.7.5 version.
I am using Signal Express 2012 and the SMU to plot the I/V characteristics of FET and other active devices. I am able to obtain the anticipated curve traced results but I am not able to Export the data to Excel directly from the Data View using the Microsoft Excel option. The error message is: Data could not be sent to Microsoft Excel. Please ensure you have a properly licensed version of Microsoft Excel. See attachment.
We have checked our version of Microsoft Office, it is Professional Plus and has the correct volume license so it does not revert to a home or student version.
I have been able to use the Export to Excel function directly from the Dataview when I was using one of the waveform tutorials supplied with Signal Express so I suspect it is a function of the SMU.
In conversations with an NI support engineer he felt it may be a problem with "an active x call is just not seeing the license for some reason", his suggestion is to drag the data into Excel rather than use the Data view tab. Because the SMU is being used in a production environment it is not really appropriate to have the operator work at this level so I would rather figure a way to have the data exported using the Data View tab.
Anyway please can you let me know if there are any known work around for this issue.
Thank you

Calvin1957,
I am not seeing any attachments in the first post or this latest post. The images should be added using the attachments section when creating the post. You should also be able to insert an image using the insert image button in the toolbar. Let me know if you have any questions. Thanks!
Robert B
Applications Engineer
National Instruments

Problems with signal level around the house ????

Hi Guys,
I have had my BT Home HUb 2.0 for just about a month now and after having very little luck with my new laptop which i have replaced twice and am now on my 3rd (Samsung) all working well, i am still having problems with using my laptop with the home hub about my house.
I have strong signal downstairs obviously cause that is where home hub is situated, and it is central to the layout to the house, but if i take my laptop upstairs i have no signal again, i say again as when i first fitted home hub i had good signal upstairs of 3/4 bars. I have tried changing the channel and have found that channel 11 is the one for here.
The only thing i can put it down too is that the other day i tried to get the router set up no more than 5 feet from where it is now as i am also trying to get my old pc tower to work from it too (pc tower has no internal wireless card so have a wireless adapter) but signal again is very poor, since i tried that and also laptop has manufacterer update for a new driver to be installed which i installed which was for the wireless facility on laptop ( which since i have done a system restore ), since all of this i have struggled to get strong signall all around the house only in fromt room as hub is situated in hallway next to front room.
Please help, as i am not having very muchg luck ???
regards
joe-sud

Other external interference maybe.
I had a problem last year with my car remote transmitter not working unless within a few inches of the drivers window.
Using a radio scanner, I found a signal on the same frequency that my remote uses.
After eliminating all other possabilities, including total power down of our house to eliminate ANY of our equipment, I contacted Ofcom http://www.ofcom.org.uk/complain/inter/intbr/ and made a formal complaint.
A few days later the investigator arrived with some really hi tech scanning gear, and within 5 mins had identified the scource was eminating from next door.
He found the culprit....next door had a Sky remote extender which had gone faulty, and was flooding the area with a constant signal.
There is no charge for this service as long as its not your own equipment, which is why I powered off the whole house to see if the problem persisted.
Maybe you could use an extention lead from next door to power your router while turning your mains off to check?

Problem in signal extraction from ELVIS using biomedical startup kit

hi,
i am using executable version of biomedical startup kit 3.0. i want to use ECG signal. the problem is that i am using ELVIS for signal extraction from biomedical kit. but when i connect it with ELVIS, connected osciloscope with channel A0 and A1, but it showed no signal on osciloscope. can anybody tell me what can be the reason for that???

Support for the Biomedical Toolkit is provided on our Biomedical User Group at www.ni.com/biomedusers
Visit the NI Biomedical User Group at:
www.ni.com/biomedusers

New Mini Projector Problem - NO SIGNAL on Daily Restart

I just got a new Mac Mini. I have it connected to a Mitsubishi XD490 projector using the DVI adapter that came with the machine. Everything works great, until the next day. I have my Mini Set to auto shut down each night, then startup new in the morning. The computer starts up, and I can find it on my network, but when I turn on the Projector, the projector says that it has "NO SIGNAL" from the Mini. I then push the power button on the Mini and restart it with the projector on and everything works great! I have the Display Sleep mode set to off in System Prefs. I can turn off the projector and turn it back on during the day with no problems. The problem only happens after the nightly shutdown.
What could be causing this "NO SIGNAL" message from my projector?
Kevin

It sounds like the Mits projector is in violation of the part of the VESA spec dealing with EDID that says a host system (mini in this case) be able to supply auxiliary power to the DDC function within an attached display in the event the display is in a power off state. OK, that was a lot of jargon, but basically what it means is when the projector's power is switched off, it becomes invisible to the mini.
What happens if you just let the mini sleep instead of powering it off completely each night? Can it recover from sleep mode even though the projector is off? That would be one possible solution.
The only other solution would be to get one of those EDID replicators. There are a few on the market that I am aware of.
http://www.gefen.com/kvm/dproduct.jsp?prod_id=4714
http://www.gefen.com/kvm/dproduct.jsp?prod_id=4715
http://www.monoprice.com/products/product.asp?cid=101&cp_id=10110&cs_id=1011003&pid=3048&seq=1&format=2

4.2.1 problem with signal

Hi all,
After the installation of the new software 4.2.1 i got problem with the signal on my 3gs, at the beginning was a little problem but within the last 2/3 weeks i need the shut it down several times to get sms sent or call working.
Wat could i do to solve this problem? this is becoming really annoying.
tnx
Andrea

Also, with proper use of the recovery and black point sliders, I'd think it would be pretty rare to really crank those "Advanced" values.
There's a creative side to this brick that I find goes beyond simple recovery. I admit to using it less now that we have the definition slider, but it still allows for a certain "look" that I can't get with the other controls. For that, I use the advanced settings a lot and this is a problem that is entirely new to 2.1.
The problem seems to only be dependent on the Mid slider - the amount in the Shadow slider doesn't seem to matter at all. Even at 1.0 on the Shadow slider, pushing Mid C creates this effect.
Obviously going back to Black Point Comp can alleviate the problem, but there's a limit that didn't exist before.
I just noticed that playing with Radius affects it as well. Of course all of this is tied to the black levels in the picture but again, it didn't used to be this way.

Dual Display Problems - No Signal After Sleep

So, I just set up my hexacore Mac Pro with stock ram and the ATi 5870. To go along with it, I purchased two Dell U2311H monitors from Dell so that I could finally have dual displays. I then purchased two 6' minidisplayport to displayport cables from Monoprice. Also went with the Apple wireless keyboard and Magic Mouse.
Upon initial start-up, everything worked fine. The monitors needed to be calibrated, but dual display mode worked perfectly without any extra steps. I had some fun messing around for a little bit and then decided to take a break. I put the computer to sleep.
I came back 15 minutes later (couldn't stay away for long), and clicked the mouse to wake the computer back up. I heard the tower humming, but the monitors stayed black. I tapped the keyboard. Still black. Assuming it was some issue I wasn't prepared for with the wireless peripherals, I futzed around with them for a while and had no luck. Still not image on the monitors. I turned the monitors off and then back on only to get an error message explaining that the monitor was in Power Save mode. Some further exploration revealed that the monitors were allegedly getting NO SIGNAL from the computer.
Restarting didn't help any. The only thing that has "worked" is shutting down the computer and connecting a single monitor through the DVI-D cable that came with it. I can then reconnect the displayport cable and switch the input to re-establish dual displays, but this is obviously pretty annoying. It seems like I can eliminate questions with the monitors themselves or the cables. In doing some research, I've found some threads on different sites about people having similar dual display issues attributed to faulty graphics cards. I certainly hope this isn't the case, but I'm at a loss for what the problem might be. It seems odd that dual displays would work briefly only to fail after going to sleep for 15 minutes.
Sorry if this is the dumbest question ever. Is there something stupid that I'm doing wrong? Anyone have any insight?
Any guidance you guys can provide would be greatly appreciated. Thanks in advance!

I have the exact same issue. Here's the forum I've got going: http://discussions.apple.com/thread.jspa?threadID=2686085&tstart=90
I called AppleCare because this issue was out of the box. Engineering wanted to capture some logger information so I ran the logger and sent it off to them.
I am running a Dell 27" via a DisplayPort to Mini-DisplayPort cable (also purchased through Monoprice) and a Dell 22" via DVI to DVI (have also tried with the DVI to DVI cable connected to an Apple DVI-MiniDisplayPort adapter and the same issue arrises). When I boot the computer with any of these cables, I get no video. Only when I boot with a Dual-Link DVI (DVI-D) cable from the 27" monitor do I get any video on screen. At this point, I can then plug in the DisplayPort to Mini-DisplayPort cable and the regular DVI (not Dual-Link) after unplugging the DVI-D cable and I get video. If I restart the computer, no problem. However, if the computer goes to sleep or if I power down and then power back up, I am back to square one with no video and have to resort to using the Dual-Link DVI cable.
Because this was DOA out of the box, they ended up just RMA'ing the machine and re-ordering my CTO Mac Pro 6-core. Still waiting for it to be built, I'll let you know how it goes on the second machine when it arrives.

Problem in signal processing

Hello all,
I use LabVIEW 8.2 student edition. I have the problem to split the output of FFT.
The harmonic component has more then one output:
Can I get only one of the component in harmonic component? I mean, in the result picture, there are three outputs. Can I get the first one only (in DBL type)? How to split the signal?
In the plot, the horizontal axis of the plot is time. Can I divide the number of the axis? I mean, it is written 100, 200, 300, 400, so on. Can I show it as 1, 2, 3, 4, so on?
Thank You for all the help.
Fikri Waskito

Hi Fikri,
first: DON'T save your picture as bmp, they take very long to load... Use png or jpg instead!
"Can I get the first one only?" - Use the "Index array" function to get the first element of the array.
"Can I show it as 1, 2, 3, 4, so on?" - Set the multiplier of the x-axis to 0.01 in the graph properties.
From your questions I also would advise to take some LabView lessons, there are 3 and 6 hour courses at the ni website! Have a look at the examples that come with LabView. RTFM.
Message Edited by GerdW on 08-22-2007 12:06 PM
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Problems recovering signal when iPhone 5 lost it. Bug?

Hello,
I'm experiencing random problems with my iPhone 5 when I lost the gsm signal (i.e. When I go down to a parking). When I go up to the street the iPhone cant recover the signal and 'no service' message appears. The problem happen randomly, sometimes the signal appears again.
I think that this may be a bug because there are three different iphones 5 in my family and I have experienced the probem with all. The three iphones are in 6.0.2 and the cell operator is different in each one.
Anybody has experienced problems like this?

I originally bought my phone, well actually pre-ordered it, from ATT here in the US. I had issues with the connection loss from day 1 of getting it activated. I spent probably about 30 hours over the course of 6 months on the phone with ATT and Apple support. Apple always blamed ATT and ATT blamed Apple. I had a friend who worked for ATT and he went through all my stuff that ATT handles and got it all set up properly and I still had the issue. After that I concentrated on Apple.
I did, however, a couple weeks ago get my phone replaced after spending 2 hours on the phone with Apple arguing that I was still having the issue and Apple trying to push the blame to ATT and the support person even went as far as to put "DO NOT REPLACE PHONE" in my support notes, the rep in the Apple Store didn't notice me reading the notes over his shoulder. Long story short, phone replaced and still have the issue.
I've noticed if I'm on 4 bar LTE and I get a phone call it will drop to 1 bar 4G while it is ringing and stay that way for about 5 minutes after they leave a voicemail. I have officially decided to switch to the Galaxy S4 because I am tired of having a phone that doesn't work, which is very dangerous. Prime example. I live in Oklahoma, where a tornado hit 3 miles from my house. My wife called me to warn me. After that phone call I could not send a text, EVEN WHILE ON WIFI, or make a phone call. I spent 15 minutes resetting the phone and trying everything I could to get a call to her to tell her I was okay. I actually had to turn my xbox on and have a friend in another state call her for me to tell her I was okay and my phone wouldn't work. My brother, who lived 2 miles away had no issues with his ATT Galaxy S4 when I was having issues so it wasn't due to the storm. I recommend that if you have an Apple Iphone 5 that has issues, switch to the Galaxy S4 or another smart phone. I think there are more Iphone 5s with the connection issue then there are without connection issues.

Problems with signal when I receive a new yahoo-ma...

hi - my phone is a nokia 5230
I still receive a signal 24/7 when I get a new mail from my yahoo-account even though my settings in "Usersettings" for email is tagged "NO"?
In "Usersettings" for sms I have tagged "Receive report" as I dont know how to set the phone back to the more the precise terms: "Receive Signal" or not when I am receiving an sms -
Suddenly one day this option "Receive report" was my only option without me having changed anything...and the email settings used to be okay too earlier?
I have switched the phone down and opened it again but it doesnt help?
As I dont have nothing important on my phone I consider to reset to Factory settings but here is my only worry to install the free Ovimap again as it became a problem last I tried and the phone ended up being repared.
Yours Per

Hi jclark735,
Do you have sound in videos and other sites? Is it only Facebook that you don't get sound? You might have accidentally muted audio for Firefox. The article Knowledge Base article [[No sound in Firefox]] will show you how to check.
Hopefully this helps!

Problems with signal and wifi

Hi there, I've had problems with my phone signal coming and going the past few days I restart my phone but it doesn't always come back, it's a repeated thing, especially when I'm in my room, texts won't send and my wifi goes off and on when I'm using it and I can't maintain a connection, the wifi itself is fine, it seems to be problems with my phone, please could you help,
Thank you

Hey
I try and check back on threads regularly, but yep, tagging me will notify me.
Hmm, I've had a check on Google and a few people do experience signal loss issues... as you're saying you have WiFi problems too, I believe this may be related to the phone rather than EE.
I had a look and there doesn't seem to be a lot of issues in the area you've told me about. You also mention it works at your friends, so again, location doesn't seem to have any impact on this.
Have you tried removing the SIM card, turning the phone off, inserting the SIM again and then turning the phone on? I'd also remove the SIM, wait 10 seconds and then insert it again whilst the phone is still on.
You may also want to try turning flight mode on and then off again - I read online that this has solved the problem for a few people.
Let me know if any of the above works, and if not, I'll see what other advice I can offer. I can't rule out for certain it's not an EE issue... but we'll soon find out I'm sure!
Thanks,
Titanium

CNN HD,,,,,problems with signal/feed?

I am in the SE part of the US - SWFL to be exact. I am wondering if anyone else might be experiencing signal issues with CNN HD? It seems like it skips and freezes up momentarily several times within a 2-3 minute period, and always seems to occur after 2:00pm ET ..... CNN SD does not have this issue - just the HD version.

I am having the same problems I reported it to support however they said they fixed it. I still have the problem about every 2 hours my audio skips and the screen looks like the video is intermitting with little squars all all over the screen. They were sending a teck over but it doesn't happen all the time. Like yesterday it did it about 8 times. I only happenes to CNN and it is on 2 TV's with different boxes. I am in the Hudson Florida area.

NDrive GPS problem no signal. Status: no fix

Hi everyone,
Sorry for my poor english.
Some hours ago, i bought NDRIVE 10.1.14 Italia.
Now when i try this apps..the status of GPS is NO FIX.
The device don't found the gps signal.
I have an iPhone 3GS 32GN OS 3.1.3.
Someone had my same problem?
Thank you very much...

Do you get a good fix with the Maps app?

Problem in signal Q 10

Similar Messages

Maybe you are looking for