Problem in USB 3.0 (two ports) win 8.1

I 've an extenal hard drive and my usb 0.3 ports have read it as usb 0.2 and still read it as usb 0.2 port
any help .......?
This question was solved.
View Solution.

@3rafa
Was your notebook originally running Windows 8.1?
Try going through this process and see if you have any luck.
HP PCs - Troubleshooting USB Connections (Windows 8)
Also here is the: HP Pavilion g6 Notebook PC - Maintenance and Service Guide
From the specifications one of the ports is a USB 2.0 port and the others are USB 3.0. You have probably already checked this, but if you used the one on the right side it is a USB 2.0 port.
USB 3.0 ports (two on left side)
USB 2.0 port (right side)
I hope this helps.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Similar Messages

K7N2 deltas mainboards have a problem with usb devices ??

Ok here is my problem..
I had installed WinXP Pro with SP1..
I got a 20 GB USB2.0 disk.i connected it on the both front or rear usb ports.
When i tried to transfer files to my usb disk or to my PC, in the middle of the copying, i got "Write Delay Failed" error and lost my usb connection..
I had to plug it out and in again..
Now, i have an DSL modem..Last night, i was disconnected from internet and my modem's lights gone..I plug it again, no lights..restarted my PC, also completely shutdown Windows XP..Again no lights..
Then, formatted PC and installed windows 2000 Pr and SP4, until now, my modem worked fine..But USB 2.0 ports are still no use for my usb disk...
In bios , it's enabled as USB 1.1+2.0..
I think this K7N2 deltas have a problem with usb 2.0 devices and Win XP Pro..
Some guys talking about, removing 9th wire earth, but couldn't understand which wire from where ? From mainboard or from usd device's cable ?
Those cables are fabricated, i think it's impossible ?
My processor is Athlon 2500+, ram Twinmos 512 DDR 400
Thanks for reply

I'm also having this problem. It's happening with my USB flash disk. I was almost buying another one when I tried it with Windows Vista on the same machine and it worked ok, then I tried Arch Linux (with kernel 2.6.30.5) on another machine and got the same error. After that I tried Ubuntu and it worked ok. Seems that Arch's kernel doesn't like my USB flash disk.
Last edited by esdrasbeleza (2009-09-02 01:16:09)

My laptop macbook pro has a problem with usb port they are not working.

hi there i have a late 2011 mac pro, its been 2 years of purhase however reary used, now it has a problem with usb port are drawing too much power and usb ports are dissabled from the system. now i can not use usb ports. do yo have solution for it??? cheers

Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
Best.

Been using an Avastor HDX-800 for storage and backup, also a SUPERDISK for smaller stuff; recently the SUPERDISK does not appear on the screen, and the light blinks while you hear it spin, also the Avastor has started to have the same problem, both USB

Been using an Avastor HDX-800 for storage and backup, also a SUPERDISK for smaller stuff; recently the SUPERDISK does not appear on the screen, and the light blinks while you hear it spin, also the Avastor has started to have the same problem, both USB conncected, both worked well before, but both now spinning, blinking, and not showing up on the screen as before,
Interestingly they both appear in the System Profiler, but just not working the same as before
I have tried other USB ports, but the same responce,

yes I did reset the PRAM, but no benefit, still the same problem
my usb devices are: keyboard, mouse, printer, SD-USB-M3, and LaCie d2 DVDRW:
the mouse and printed are plugged into the keyboard: i have tried to move, these around, and have even tried just the mouse, printer and SD-USB-M3, but still the same problem
here is a cut and paste of the current "System Profiler>Hardware>USB"   (usb device tree)
USB Bus:
Host Controller Location:          Built In USB
Host Controller Driver:          AppleUSBOHCI
PCI Device ID:          0x0026
PCI Revision ID:          0x0000
PCI Vendor ID:          0x106b
Bus Number:          0x18
Hub in Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x1002
Vendor ID:          0x05ac (Apple Computer, Inc.)
HL-1270N series:
Version:          1.00
Bus Power (mA):          100
Speed:          Up to 12 Mb/sec
Manufacturer:          Brother
Product ID:          0x0008
Serial Number:          L9J286292
Vendor ID:          0x04f9
Basic Optical Mouse:
Version:          0.00
Bus Power (mA):          100
Speed:          Up to 1.5 Mb/sec
Manufacturer:          Microsoft
Product ID:          0x0084
Vendor ID:          0x045e
Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          250
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x0204
Vendor ID:          0x05ac (Apple Computer, Inc.)
SuperDisk USB 120MB drive:
Version:          0.0e
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Imation
Product ID:          0x0002
Vendor ID:          0x0718
Hub in Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x1002
Vendor ID:          0x05ac (Apple Computer, Inc.)
HL-1270N series:
Version:          1.00
Bus Power (mA):          100
Speed:          Up to 12 Mb/sec
Manufacturer:          Brother
Product ID:          0x0008
Serial Number:          L9J286292
Vendor ID:          0x04f9
Basic Optical Mouse:
Version:          0.00
Bus Power (mA):          100
Speed:          Up to 1.5 Mb/sec
Manufacturer:          Microsoft
Product ID:          0x0084
Vendor ID:          0x045e
Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          250
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x0204
Vendor ID:          0x05ac (Apple Computer, Inc.)
HL-1270N series:
Version:          1.00
Bus Power (mA):          100
Speed:          Up to 12 Mb/sec
Manufacturer:          Brother
Product ID:          0x0008
Serial Number:          L9J286292
Vendor ID:          0x04f9
Basic Optical Mouse:
Version:          0.00
Bus Power (mA):          100
Speed:          Up to 1.5 Mb/sec
Manufacturer:          Microsoft
Product ID:          0x0084
Vendor ID:          0x045e
Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          250
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x0204
Vendor ID:          0x05ac (Apple Computer, Inc.)
SuperDisk USB 120MB drive:
Version:          0.0e
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Imation
Product ID:          0x0002
Vendor ID:          0x0718
USB Bus:
Host Controller Location:          Built In USB
Host Controller Driver:          AppleUSBOHCI
PCI Device ID:          0x0026
PCI Revision ID:          0x0000
PCI Vendor ID:          0x106b
Bus Number:          0x19
LaCie d2 DVDRW USB:
Capacity:          451.76 MB
Removable Media:          Yes
Detachable Drive:          Yes
BSD Name:          disk2
Version:          0.00
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          LaCie
OS9 Drivers:          No
Product ID:          0x1011
Serial Number:          FFFFFFFFFFFF
S.M.A.R.T. status:          Not Supported
Vendor ID:          0x059f
LaCie d2 DVDRW USB:
Capacity:          451.76 MB
Removable Media:          Yes
Detachable Drive:          Yes
BSD Name:          disk2
Version:          0.00
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          LaCie
OS9 Drivers:          No
Product ID:          0x1011
Serial Number:          FFFFFFFFFFFF
S.M.A.R.T. status:          Not Supported
Vendor ID:          0x059f

Do we need two ports for establishing one connection to EJB from swing clie

Hi all,
I have an application which uses Java Swing client and accesses an EJB to connect to the server.
I am connecting to the EJB using iiop://server-ipaddress:port.
It is required for me to open the firewall to access the above specified ip address and port number. Even though, I am able to access the specific ip address and port number, I am not able to establish the connection.
I tried out to check the porblem and I came to know that, this aplication is trying to open another port also on the same IP address.
I am just wondering whether we need two ports for one connection.
Does anybody face this type of problem?

If you need to access on two ports, you would have to open both :)

I meet a problem on rtp , Only use one port in the project ,how to do

the customer only permit we transmit and receive data on the same port . how to do this , I've never developed JMF & RTP before . And I meet problem , when i use the same port , it warning port is occupied .
what should I do to solve this problem>? help

If you want to use the same port to send and receive, youcan't use the same computer to test with. The port you choose will be bound by the sender, and will thus be unavailable for use by any other thread/process/program on the same computer.
Use two computers, everything should work fine.

SAS MPIO Driver Server 2012 HCT Fails with "make sure two ports are connected" error even with two ports connect

We are running the Server 2012 HCT against a SAS MPIO driver for a server platform with dual redundant storage controllers. The test fails with this error:
(x) For non-iSCSI test environment, please make sure at least two HBA ports are connected to the storage target.
File=testsrc\driverstest\storage\wdk\mpiotest\logotest\devicelib\mpiodevice.cpp Line=2772
Error: 0x0, Error 0x00000000
The system does have two ports connected so the cause of the error is unclear to us. We do not have any problems when running the 2008R2 HCT. Are there any known issues or fixed or workarounds for this problem?

Sorry, maybe I should say WLK rather than HCT. We are trying to submit the SAS MPIO driver for WHQL signing.
Here is a sample MPIO snapshot where you can see our driver is controlling five drives each with two paths.
MPIO Storage Snapshot on Wednesday, 17 April 2013, at 18:31:40.275
Registered DSMs: 2
================
+--------------------------------|-------------------|----|----|----|---|-----+
|DSM Name | Version |PRP | RC | RI |PVP| PVE |
|--------------------------------|-------------------|----|----|----|---|-----|
|Microsoft DSM |006.0002.09200.16384|0120|0003|0001|030| True|
|Intel(R) Storage Controller MPIO|004.0001.00140.0002|0120|0003|0001|030| True|
+--------------------------------|-------------------|----|----|----|---|-----+
Microsoft DSM
=============
No devices controlled by this DSM at this time!
Intel(R) Storage Controller MPIO Driver
=======================================
MPIO Disk4: 02 Paths, Fail Over Only, Explicit Only
SN: 2263015539BAB
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Standby 000|000|001|004 0
TPG_State: Standby , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: EBF4115500000000 (State: No Controller)
0000000077000000 Active/Optimized 000|000|000|004 0
* TPG_State: Active/Optimized , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
MPIO Disk3: 02 Paths, Fail Over Only, Explicit Only
SN: 22201556966AB
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Active/Optimized 000|000|001|003 0
* TPG_State: Active/Optimized , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: EBF4115500000000 (State: No Controller)
0000000077000000 Standby 000|000|000|003 0
TPG_State: Standby , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
MPIO Disk2: 02 Paths, Fail Over Only, Explicit Only
SN: 226E01556E6C5F
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Active/Optimized 000|000|001|002 0
* TPG_State: Active/Optimized , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: EBF4115500000000 (State: No Controller)
0000000077000000 Standby 000|000|000|002 0
TPG_State: Standby , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
MPIO Disk1: 02 Paths, Fail Over Only, Explicit Only
SN: 227C01558F689E
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Standby 000|000|001|001 0
TPG_State: Standby , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
0000000077000000 Active/Optimized 000|000|000|001 0
* TPG_State: Active/Optimized , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: 6E9AD05300000000 (State: No Controller)
MPIO Disk0: 02 Paths, Fail Over Only, Explicit Only
SN: 22F10155FB941D
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Standby 000|000|001|000 0
TPG_State: Standby , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
0000000077000000 Active/Optimized 000|000|000|000 0
* TPG_State: Active/Optimized , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: 6E9AD05300000000 (State: No Controller)
MSDSM-wide default load balance policy: N\A
No target-level default load balance policies have been set.
================================================================================

Satellite M70-190 - problem with USB

Hi!
After uninstall Windows XP and BIOS update, i have a problem with USB ports. My USB flash drive does't work. Windows find it as USB flash drive, but i can't find it in "My computer"
So have anyone idea about this problem?
PS External HDD works perfect, as USB mouse, and USB WiMax modem.
Im hoping someone out there can help with this problem.

Is described issue the same on all USB ports?
I mean, I have Satellite M70-159 in front of me and since long time I use 8GB SanDisc and 2GB Toshiba USB stick and both devices are recognized properly.
I still use original Toshiba WXP installation (updated of course).

Solving Prolific PL-2303 USB to Serial Comm Port installation issues

Hello everybody,
More and more machines are comming without Parallel and serials ports, they are comming with USB external ports only.
Some have the RS-232 and Parallel headers in the motherboard, and that should last for about a year I think.
At any rate, the issue I was facing is the following:
(a) Installing Prolific PL-2303 USB to Serial Comm Port on Windows XP Pro SP3 works OK and system runs fine. there are some capacity issues regarding the buffer size, but that is another post.
(b) Installing on WEPOS 1.1 SP3 on some motherboards (Older ones) that have at least the Parallel headers and a serial port, the device also works as with (a)
(c) Installing on WEPOS 1.1 SP3 with a machine with only external USB's (no parallel / serial port or headers). The installation process runs OK. but when the device
is plugged I get the following error message:
"An error ocurred during the installation of the device"
"A service Installation section in this INF is invalid"
(d) Installing on POSReady 2009. I get the same as with (c)
This is how I solved, after many frustrating reboots with the same message about the INF section and multiple Prolific drivers tried. I started digging windows:
(1) Find the setupapi.log and read it, if the OS is a fresh install it will not be too long.
(2) Read this:
#-166 Device install function: DIF_SELECTBESTCOMPATDRV.
#I063 Selected driver installs from section [ComPort] in "c:\windows\inf\oem15.inf".
#I320 Class GUID of device remains: {4D36E978-E325-11CE-BFC1-08002BE10318}.
#I060 Set selected driver.
#I058 Selected best compatible driver.
#-166 Device install function: DIF_INSTALLDEVICEFILES.
#I124 Doing copy-only install of "USB\VID_067B&PID_2303\5&B6C3FC&0&2".
#-166 Device install function: DIF_REGISTER_COINSTALLERS.
#I056 Coinstallers registered.
#-166 Device install function: DIF_INSTALLINTERFACES.
#-011 Installing section [ComPort.NT.Interfaces] from "c:\windows\inf\oem15.inf".
#I054 Interfaces installed.
#-166 Device install function: DIF_INSTALLDEVICE.
#I123 Doing full install of "USB\VID_067B&PID_2303\5&B6C3FC&0&2".
#-035 Processing service Add/Delete section [ComPort.NT.Services].
#E339 Add Service: Binary "C:\Windows\system32\DRIVERS\serenum.sys" for service "Serenum" is not present.
#E032 Error 0xe0000217: A service installation section in this INF is invalid.
#E275 Error while installing services. Error 0xe0000217: A service installation section in this INF is invalid.
#E122 Device install failed. Error 0xe0000217: A service installation section in this INF is invalid.
#E154 Class installer failed. Error 0xe0000217: A service installation section in this INF is invalid.
[2010/02/13 23:32:24 2004.2]
(3) So it was the serenum.sys file that Windows needed to find in the ..\system32\drivers folder. I got the serenum.sys from one of the temporary folders created by the installation process.
(3a) So, I think that windows installs this sys file if it recognizes the motherboard has at least one parallel or serial port.
(4) So good luck when installing your serial device to your POS solution. I will open another thread if I have problems with the buffer size of the device.
Humberto Sequeira

Hello Terry,
Indeed, they were not intended as POS system, the EEE Top machines are candy to the eye, but for my taste they do not work in POS environment (I give them 1 year before they pop). Regarding the other, well competition is tought, so you have to get creative in order to keep costs down, and this one can be used as a waiter stations, that do not need heavy serial comunications.
Anyways, the POSReady does not install these system files if the installation does not detect a serial or parallel port (which make sense, as why would it install drivers for a device that is not detected). I posted this for others to be aware of this when they select the hardware that will be offered to their customers, as good old "on mother-board" serial and parallel ports cannot be beaten by their USB imitations (IRQ and memory addressing processing are needed for end devices to function properly).
Have a great weekend,
Humberto

Yosemite problems withAnker USB 3.0 Hub ?

Anker USB 3.0 7-Port Portable Aluminum Hub gets great reviews but cautions about undefined Yosemite problems???

Funny ... Isn't Yosemite an Apple product. Thought maybe others might have some experience with the accessory named.

MSI RS480M2 - USB Problems - RS480M2 USB

Anyone having any strange behavior using wireless USB kb and / or USB mouse on the MSI RS480 board?
I have 100% failure rate using 3 different wireless keyboards... The only way to fix is to reboot the system which will reestablish the connectivity. then in about 1-3 days I loose the wireless kb connection. USB trackball mouse is fine except for some studdering.
this is killing me - but I'm hopeful a bios fix or something related to my setup could be to blame. Anyone? Moderators? The MSI quality seems very very good. Should I contact MSI support?
I use bios rev. 3.2
specs:
a64 3200 939; msi rs480; corsair xms3200 1gb; x700pro 256mb; pioneer dvd108; wd 200gb 8mb cache; silverstone LC11 w/ 240W tfx w/ pfc, 3.3v @18A, 5v @19A, 12v @16A

Quote from: dannol48 on 06-May-05, 05:34:47
I do have a Logitech wireless keyboard and mouse, but have them connected PS/2. I'll test them in USB when I get a chance. I usually avoid USB when PS/2 ports are present.....It just seems to avoid problems.
I haven't had any problems with the USB 2.0 Flash memory reader on USB internal. No systems log errors to indicate any type of USB problem. I've even booted from the Flash (I posted a thread on that result). I tried a USB 1.1 CAM on all the ports front and back to verify they were working, but not any prolonged tests. Sounds like more testing is needed.
I have seen mention (during google searches on the chipset) of a possible issue with ATI's USB having problems. ATI seems to have licensed alot of what's integrated on the SB400 from others, so I check who and what on the USB. Drivers are always a possibility. I do have XP-SP2 installed.
Danno
Edit: OK...you guys got me concerned enough that I just switch to USB on keyboard and mouse. They detected and installed fine. I'll let you know if it fails in the next hour. I'll try Sleep mode and return too.
Edit2: Sleep works...no problem other than it asks what I wanted to do when I hit the Sleep button on the keyboard. I use a "giggle" on the mouse to return from sleep. I looked at the USB vendor codes and they're ATI's. It's using the standard generic SP2 drivers. Other than waiting, any way to MAKE IT FAIL? I will stay with USB for the next few days and report back any problems.
Edit3: Since there's no room in my profile, here's the link to my keyboard-mouse.
http://www2.newegg.com/product/product.asp?item=N82E16823126131
thx Dannol48, I use logitech elite, memorex, msft black standard wireless, even a phillips wireless kb. all work great... then after 1-3 days I need to reboot.
I run MS XP MCE2005 w/ Ms remote + at least 4 other USB devices attached besides the wireless KB. the usb trackball (MSFT thumb ball) mouse is attached via a USB hub I velcro'd to my couch. I operate this 20ft away from the TV - which is the only display device. I've loaded the OS 3X now trying to isolate if it's the OS w/ no change.
I've been using a very similar setup to above for about 4 years now. never had an issue like this. It could be ATI issue... or BIOS? i dunno.

MSI K8N Diamond - Boot problems with USB devices attached.

Hi There.
I have been seeking the forums, but havent found the answer to my problem yet.
This is how it goes with ANY USB devices attached to either of the four USB ports on the Motherboard.
When i turn on my system, it hangs in the POST right after displaying the BIOS version (Which I have updated to 1.6) - I cant use my Keyboard to get to the BIOS setup.
Without USB devices attached...
The system boots without problems. And in Windows XP SP2 i can insert my keyboard, mouse etc. and everything works great - both USB 1.1 & 2.0 devices.
I have disabled the KB/USB.. in BIOS and I have disabled the "Boot on other device" option as well.
As I have found on this forum, a lot of people have problems with USB Front panel and D-Bracket (USB ports) connectors causing the system to hang - But my D-Bracket (USB connectors) and my front USB port is at this time DISCONNECTED - so this cannot be the problem.
The D-Bracket shows the "Bios Sign On" information - and stops at that point
Am I having a malfunctioning Motherboard here, or are there any solutions to this problem?
Please help me as I am desperate to have my system work properly.
Regards
Stieper

Well I have read about that somewhere in here, but my problem is NOT with an USB hub, but with any USB device attached to the motherboard's USB slots. It is driving me nuts to be honest!! I think it might be time for RMA
What do you say guys - is my Motherboard ready for RMA, or do I have to try something specific berfore sending it to the retailer??

Satellite M30X: Problems with USB 2.0 external HDD

Hi,
I have a Toshiba Satellite M30X. I recently bought myself a 200GB External Hard Disc. It has its own Power supply. If I connect it with USB 2.0 to my Laptop it happens to diconnect and reconnect permanantly. Sometimes it works, then I can put Data on the Disc. Then again it diconnects and reconnects many times. I've already tried another USB Port, but there is no difference. It's very strange, because I connected the External Hard Disc to many other Computers (Laptop and Tower) and it ALWAYS works!!! Its only with my Laptop it disconnects and reconnects the whole time. As I said, not always. Sometimes it works for like an half an hour or so then the action starts again ...
Can somebody help???
Greez Lutz

Hi Andrea
I really dont know why this happen. A friend of mine has the same problem with his desktop. While copy process runs the HDD is suddenly disconnected and there is also acoustic sound when the hardware is removed.
I have connected his HDD on my Tecra and there is no problem. I really dont know what the problem can be. Maybe there is some problem with OS because I can not believe that there is some contact problem with USB ports.
If you use many different USB devices at the same time maybe there is some conflict between few different drivers. Sorry but it is not easy to give some precise explanation.

How can I use two ports in the same time?

My application need one pc use two ports the same time.But when I open one port and my systerm is running the other port can't be opened.
I use the frame API in VC++6.0.
My OS is win2000 server;
The functions I used are ncOpenObject();

Hi DickW
Thank you for your help!
I have tried the example.But the example shows how to connect one CAN network with two ports.
I want each port connect to the net can both read and write;
I want to apply the function like this:
1.config the port1 and port2
2,open port1 and port2
But after I open port1 or port2 the other port can't be opened;
After I open the second port it always returns negative.
In the codes I use CAN0 and CAN1 as the CAN objects.
Attachments:
twoport.zip ‏1184 KB

Re: if weblogic can serve two ports at the same time?

That's not true. WebLogic supports a non-secure and secure listener port at the
same time. That was one of the selling points for my organization.
Michael Girdley wrote:
If, you mean the same port on two different IP addresses, then the answer is
yes.
If, you mean two different ports on the same IP address, then the answer is
no.
Thanks,
Michael
Michael Girdley
Product Manager, WebLogic Server & Express
BEA Systems Inc
fxy <[email protected]> wrote in message
news:8fdk99$t9$[email protected]..
<URGENT QUESTION>
I'd like to know if weblogic can support two ports at the same time.
thank you in advance.
<URGENT QUESTION>

Well, the question was really meant to see if any change was made to WL to support
this, not because I didn't believe Michael Girdley.
P.S., this is something Websphere 4.0 let's you do...In case this encourages someone
to add this support.
"Mike Reiche" <[email protected]> wrote:
>
If you don't believe Michael Girdley, then I don't know why you would
believe anyone
else. I believe the answer is still 'no'.
Why do they 'have to be on different ports'? We block requests by URI
- so just
block all requests to /youradminapp/* at the firewall. Or you can block
them at
your Web Server. Or restrict them by user in WL.
Mike
you"Anil Arora" <[email protected]> wrote:
Is it still true that WL 6.0 cannot host multiple (non-secure) HTTPports
on one
server? We need this capability within one JVM to allow one web application
to
be accessed from one port while another through a second port. Forexample,
we
have a application to be exposed through the firewall at port 7001.
Then we have
another admin application to only be accessed within the firewall. But
they need
to be deployed within the same JVM since they may have shared statebetween
them.
Thanks,
Anil
"Michael Girdley" <[email protected]> wrote:
I'm sorry, to clarify my statement: I was speaking about nonsecure
communications. Weblogic can only support one listener port at a time.
Thanks,
Michael
Michael Girdley
Product Manager, WebLogic Server & Express
BEA Systems Inc
Allen Akers <[email protected]> wrote in message
news:[email protected]...
That's not true. WebLogic supports a non-secure and secure listenerport
at the
same time. That was one of the selling points for my organization.
Michael Girdley wrote:
If, you mean the same port on two different IP addresses, then
the
answer is
yes.
If, you mean two different ports on the same IP address, then theanswer
is
no.
Thanks,
Michael
Michael Girdley
Product Manager, WebLogic Server & Express
BEA Systems Inc
fxy <[email protected]> wrote in message
news:[email protected]...
<URGENT QUESTION>
I'd like to know if weblogic can support two ports at the same
time.
thank you in advance.
<URGENT QUESTION>

Problem in USB 3.0 (two ports) win 8.1

Similar Messages

Maybe you are looking for