Problem Installing AMD Proprietary Driver.

Hey Guys,
    As the title says I am having a problem installing the amd catalyst beta driver. I tried installing it and it completely screwed everything up. Now I have a fresh install of Arch, and the only packages that I have installed apart from xf86-video-ati and xorg are enlightenment, lightdm, gnome, base-devel, and firefox. Im not sure what is wrong. The only thing it mentioned in the log was something about needing 3.8 headers, but if i am not mistaken Arch has 3.12. I also installed it on a linux mint system with 3.11 and it went without any issue. I believe that it is supposed to work on 3.12, but im not sure what I need to get it to install on my system. Any help would be much appreciated.

Sorry for getting back so late. @HalosGhost I have always used the one that came directly from AMD and since this is my first time using Arch i did not know that I would run into problems trying to use it. As far as the --force thing goes. I had a "What the Hell Moment". @Archivist: catalyst-test worked, but my sound via HDMI does not.
aplay -l shows my HDMI:
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: Generic [HD-Audio Generic], device 0: ALC887-VD Analog [ALC887-VD Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
I also tried  aplay -D plughw:0,3 /usr/share/sounds/alsa/Front_Center.wav and it worked without any error.
I then tried creation an .asoundrc file like the wiki said https://wiki.archlinux.org/index.php/Ad … s_not_work and that did not work either.
Last edited by jtag1458 (2014-02-24 16:45:14)

Similar Messages

  • Installing AMD graphic driver turns into BSOD

    Hello, I have recently reinstalled Windows on my laptop and now i can't install AMD graphic driver. Whenever I try to install it, my screen switch off ( as usual during installing of graphic driver) and then turns into BSOD with error "atikmpag.sys". After this, I am unable to switch on my computer, because there is always BSOD waiting for me and I have to reinstall windows again. This is happening with Win 8.1 and with Win 7. I have tried many versions(releases) of drivers and many ways to install them. But the result is always the same: BSOD "atikmpag.sys".
    Could u give me any solution for my problem? It is really frustrating. I am not very used to write in English, please excuse me. Regards, Patrik Obrtlík 

    AMD's 'catalyst clean utility' (stand-alone program) is notoriously bad, yes especially for switchable graphics laptops. And have heard some horror stories of that ruining windows installations needing a reinstall DDU, I would argue is perfectly safe however. It is pretty universal generic clean utility which can clean both AMD and Intel components. I use it myself(HP envy 15 with AMD+Intel), though AMD catalyst install manager (from 'uninstall or change programs' list) would work, though I don't think it cleans/removes Intel installations. 

  • Problem Installing Graphic Card Driver in Lenovo G505s AMD A8

    Configuration Processor - AMD A8-5550M RAM - 8GB (4*4 configuration) OS - Windows 10 (Upgraded From Windows 8.1) Graphics - AMD Radeon HD 8650G + HD 8570M Dual Graphics  I have upgraded my system on 30th July to Windows 10 Pro. Now i am unable to install Graphic Card Driver.I Even tried unninstalling the Drivers using DDU(Display Driver Unnistaller) in Safe Mode and tried Re-installing Driver but while reinstalling Driver my system always Restarts and installation interrupts in between I tried this 4 times then i tried using without driver but my laptop used to get thermal shutdown.So Finally i performed a System Restore, but i wanted  to perform a clean install for which this problem must be solved as i won't be able to do system restore after clean install. One more Problem after i've upgraded to windows 10 my graphic driver is recognized differently as R5 M200 but actually its HD 8570M. Observations Whlile installing Driver :Laptop gets Heated and restarts firstly i thought its a Thermal Shut Down but it restarted and i even tried to preform the installation after placing my laptop in front of air-conditioner but it again restarted.Help me out finding the solution for this problem.Warm Regards,Rishabh 

    Hi,
    Hope you've already tried this from HP support page:
    h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=6943827&swItemId=ob_148736_1&swEnvOid=4053#tab-history
    If so,
    Uninstall AMD graphics from Device Manager.
    Restart system.
    Download, save & install this:
    support.amd.com/en-us/download/mobile?os=Windows%207%20-%2032
    Restart system
    Check.
    Regards
    Visruth

  • Windows 8.1 doesn't hibernate or sleep after installing amd catalyst driver

    hi i am using windows 8.1 64 bit but after installing a amd catalyst center windows behaviour changed it doesn't go for hibernate and sleep and after unstall it windows comes into normal position please refered me proper solution to install amd driver wihout any issue and also suggest me which version will be compatible with my device i have tried amd 14.9 and also 14.11 but issues didn't solve i am curretnly using intel Version10.18.10.3325 windows update show me amd  wddi 1.3 driver but it always failed not installing..
    Hp pavilion-15 n037tx Notebook
    core i5 4200U
    4gb ram
    This question was solved.
    View Solution.

    Hi @Ahmed-Aslam 
    I understand that you are have problems with hibernate and sleep on your notebook.
    I would review the attached document. I realize from your post that you have tried some of the things listed, but just check it and see if anything there was missed, perhaps the section on malware issues.
    Troubleshooting sleep and hibernate issues in Windows 8
    You can also try using system restore to roll back to before the software update to see if that resolves the issue.
    Using Microsoft System Restore (Windows 8)
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • HP Pavilion g6-1301tx Notebook PC/ Not able to install AMD graphic driver.

    My HP Pavilion g6-1301tx Notebook PC 4gb RAM is 2 years old,My original OS was Windows 7 Home basic 64 bits then i changed it to Windows 7 Ultimate 64 bits.
    ERROR......................
    In device manager under display adapter there are two GPUs i.e. Intel Hd graphics 3000 its alright and Standard VGA graphic adapter which contains error (this Device cannot start code 10). I tried to update the driver in device manager itself but it tells ( Windows found the driver for the device but unable to install), I even tried windows update there it shows the driver update but whent i try to install it shows error Code 80070002.
    Because of this im unable to play games and watch hd videos in my laptop.
    Please some one help me to solve this problem.

    Hi:
    The only graphics driver you should install for your model is the AMD graphics driver which will install both the AMD and Intel GPU's.
    If you installed the Intel graphics driver from your PC's support and driver page, that could be preventing the correct AMD driver from installing.
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-99756-1&cc=us&dlc=en&lc=en&...

  • Problem installing HP Printer driver hplip-3.10.9

    I am trying to install the printer driver for my HP Laserjet p1102w (hplip-3.10.9.run).  The program starts then stops with the error "TabError:  inconsistent use of tabs and spaces in indentatiion".   I did some research,  but it could not resolve the issue. I think it has something to do with the way python handles tabs?? I did not have any problem installing this on my Fedora 13 desktop. Not sure how to proceed.
    Thanks!

    I have used the suggestions given, and I still can't get the printer driver to load. I did check the /var/log/cups/error-Log and found th following:
    D[08/Nov/2010:18:17:21 -0600] [Job 25] STATE: +connecting-to-device
    D [08/Nov/2010:18:17:21 -0600] [Job 25] STATE: +hplip.plugin-error
    D [08/Nov/2010:18:17:21 -0600] [Job 25] prnt/hpcups/HPCupsFilter.cpp 413: m_Job initialization failed with error = 48STATE: -connecting-to-device
    The following was from a Fedora bug report. not sure if it is applicable to my problem
    Tim Waugh 2010-04-23 11:17:41 EDT
    Description of problem:
    See in error_log from bug #520200 comment #7:
    D [17/Apr/2010:12:34:43 +0530] [Job 29] prnt/hpcups/HPCupsFilter.cpp 413: m_Job
    initialization failed with error = 48STATE: +connecting-to-device
    There is a missing newline at the end of the string output from
    HPCupsFilter.cpp:413.
    In fact, looking around, there are *loads* of newlines missed from dbglog()
    calls.  This messes up STATE and ATTR reporting, as we can see above.
    Version-Release number of selected component (if applicable):
    hplip-3.10.2-4.fc11
    D [08/Nov/2010:18:17:21 -0600] [Job 25] STATE: -media-empty-error,media-jam-error,hplip.plugin-error,cover-open-error,toner-empty-error,other
    At this point not sure what to try next

  • Problems installing second hard drive in HP Pavilion M7-1015dx laptop.

    I just bought a new HP Pavilion M7-1015dx. I have successfully installed an SSD drive as the primary hard drive and now I want to use the 1tb hard drive that the computer came with as data and install it in the second hard drive bay. I have a cable that I used from my old HP DV7 when I had a second hard drive but I am having issues with my M7-1015dx laptop.
    When I plug the sata cable into the second connector on the laptop and attach my hard drive (I have tried several hard drives) and go to power the laptop on, the power light just blinks a few times. Now I know there is something wrong for I just purchased the laptop two days ago... I got the idea to try the cable that I used to plug into the second connect to check and see if I plugged it into the first and I got the same issue, power light blinking. So I am wondering if it is the cable... is this possible? Are there different rated sata cables? I also tried the cable the came with my new laptop to make sure that it just wasn't the second port - I tried plugging it in to the second port with a hard drive attached and the laptop this time turned on but asked for a bootable disk because it requires boot disk to be in the 1st hard drive bay connection which I knew. I just want to give all the information so that I can get this fixed.
    Please help me

    Hey Brother-Brad, 
    I'm sorry you're running into issues installing a second hard drive. Your issue may not be the cable. Do you have a working hard drive installed currently with Window on it? 
    If so, 
    1. In Windows, Click the Start button.
    2. Type 'hard disk'
    3. Click on 'Create and format hard disk partitions' (aka Disk Management)
    4. Look at Disk 0 listed at the bottom in the middle. Does it say Basic or Dynamic?
    5. If it says Basic, right-click it and select Convert to Dynamic.
    Hard drives must be set as Dynamic for dual hard drives to be recognized.
    Let me know the results when you get a chance

  • Two monitors + "big screen" problem on ati proprietary driver

    After realizing ati prioprietary driver doesn't specify xrandr outputs (as konni stated on http://bbs.archlinux.org/viewtopic.php?id=66039), I tried xf86-video-ati driver and xrandr work's perfectly. However I would like to have a good 3d performance, using ATI "big screen" from it's proprietary driver.
    I think it should work using (I don't know if I have to execute  aticonfig --initial=dual-head --screen-layout=above before dtop=horizontal) :
    aticonfig --dtop=horizontal --overlay-on=1
    But it doesn't... it works as if configured it with clonning even thought it's configure to work on horizontal.
    --dtop=single does work as stated by aticonfig --help. I don't understand why an option of dtop works as stated and the other one doesn't.
    ¿Does anybody has idea what's happening or how I can figured it out?

    SiC wrote:Have you tried using the catalyst control centre to manage multiple screens? Works well for me. The latest ccc has options to enable xinerama for multiple monitors, so you should be able to sort it out from there.
    Yes I have tried and it doesn't work correctly. The second second screen, sometimes turns all black, other times strange grey lines appear all over the please. Xinerama was the last thing I wanted to try.
    I would like to use something like xrandr (one monitor is periodically moved to another desktop, xinerama isn't prepare for that, it doesn't detect if the monitor is connected or not), and thought that "big desktop" (ati names it like that) would work.
    Ati propieraty driver sucks. I will continue using xf86-video-ati drivers, it works perfectly.

  • Problems installing second hard drive and second DVD recorder

    I have tried about every combination of tricks to install a second hard drive.  I want to add a 250GB, WD IDE hard drive to my 3000J 115 7387A32 on the IDE channel.  I have set up the bios then added the drive and the reverse but cannot get computer to boot in either case.  It locks on the first screen where is says hit Enter to.... Enter makes the text go away, but nothing after. I am trying to install it as a single drive on the secondary IDE channel. 
    I know the HD is good as I removed it from another computer.  It does have Win XP on it.  I will format it using Vista IF I can get it installed.
    Basically, I am having the same problems within stalling the second DVD, which is SATA.

    Your initial hard drive should be jumpered as Master. When you install a second hard drive it must be jumpered Slave. There should be a diagram on the case of the HD showing the jumper locations.
    Power Macintosh G3 and G4: IDE Master and Slave Support and Configuration
    http://docs.info.apple.com/article.html?artnum=24342
    Power Mac G4: Installing Internal Storage Devices
    http://support.apple.com/kb/HT1815
     Cheers, Tom

  • HP Envy dv7 7250us problems installing 2nd Hard Drive

    I recently cloned my 1TB HDD to an SSD (500GB) or basically restored to it through Acronis, and it finally worked, but then I tried to install the 1 TB original drive in the 2nd Drive Bay, but when the 2nd connector is plugged into the second SATA slot, the power button doesn't work.  I disconnect the plug and the power button works again.  I couldn't find anything in the BIOS setup that you have to turn on to recognize the second drive.  Any clues?
    Thanks,
    Wendell Fry
    This question was solved.
    View Solution.

    I did the switch out of the long 2nd connector and the connector/adapter that came with the tray (short like the original one) didn't work either.  I hope it's not, but I suspect the connector receptor on the motherboard would be the next problem to think about.  Something with it is making the power switch not connect.  I don't know, when I disconnect the 2nd connector, it power's/boots right up.

  • Problems installing new hard drive

    Hi
    I have a HP Pavilion DV6000 (or according the the bios DV6700) and the original hard drive is on the way out, as the machine locks up after a short while of being logged on. I ran the hard drive diagnostics from the bios and it confirmed that there was a fault with the hard drive and i should replace it. I stupidly never made any recovery disks and as the machine locks up i cannot make any recovery disks, so im going to have to do a clean install of Vista from a CD i got from work, and thats where ive hit a problem!
    I got a new 320gb SATA drive and booted up the Vista installation but it gets stuck on "unpacking files" then eventually gives up and says "Windows cannot install required files. Make sure all files required for installation are available. Error code 0x8007045d". Ive tried a couple of different discs for Vista but it still comes up with the same message. So i thought if i put XP on it, I could then maybe upgrade to Vista..... No luck there as i got a similar message when trying to put XP on. So i went out and  got another hard drive but im still having the same problems!
    Has anyone had problems with installing a new hard drive in a Pavilion laptop? Or has anyone got a suggestion how i can get Vista on to a new hard drive? Its really getting annoying now as its something so simple normally!
    Thanks in advance 

    Similar problem. Created an image on a new WD 320gb SATA HDD, then put it in my 9000 Pavillion. All worked great, except when I then tried to upgrade to WIN7 from XP, I got the same error.  Turned off all programs, used MSCONFIG to stop everything, but it kept stopping when unpacking the files. Same
    0x8007045d error.  Tried to put the WIN7 on a mem stick to then move to the HP laptop, but everything copied except a boot.wim file in one of the subdirectories.  So I don't think that will work. Couldn't find anything that might help at the Microsoft site.

  • Problems installing new hard drive - pt. 2

    Hi there,
    I have been using a G4 for years for my music (Pro Tools). I had the standard 29GB hard drive, and I had added a second 40GB drive, and those worked well for me for years.
    A few weeks ago, the system started acting up, and it seemed like the 29GB hard drive was shot. So, I got a new one (320GB) and installed it, setting it as Master and keeping the old 40GB one as Slave.
    I tried to install both OS9 and OSX on the new drive, but had problems (as chronicled in this previous thread: http://discussions.apple.com/thread.jspa?threadID=2478863&start=0&tstart=0).
    After trying a number of things, I finally got 10.3 loaded and seemingly working. Then, I realized my old Pro Tools disc needed OS9/Classic to load, so I looked around for info on if I could load OS9 without disturbing my 10.3. I tried booting to the old OS9 disc -- I didn't actually do anything, like initialize, reinstall, or anything, just looked around to see if it was possible -- and now the 10.3 isn't working either.
    Neither the OSX installer, the OSX Disk Utility, or the OS9 Disk Utility seems to "see" the new drive now.
    Any thoughts/theories/suggestions on what it might be? Just before the 10.3 installed successfully, I had opened the computer and pressed the IDE cable connections down, just to make sure they were secure. I don't know if that did anything, but it might have.
    Now that I'm having problems again, I have of course checked those IDE cable connections again, but the computer still doesn't "see" the drive.
    I will remain calm...

    Some earlier PowerPC Macs need to have OS X installed on the first 8 GB of the HDD. Mac OS X: Disk Appears Dimmed (or "Grayed Out") in the Installer. I am not sure if that is the case with your computer, but it might be a factor.
    On the other hand, if you previously had both OS 9 and OS X installed on the HDD without an 8 GB partition the issue may be elsewhere.
    Try this:
    Format and Install OS 9
    This process will completely erase everything on your Hard Disk Drive. Be sure to Backup your User Folder and all third party apps you can't afford to lose
    • Boot from your OS 9 install CD holding down C key.
    • Go to Drive Setup and reformat your drive as Mac OS Extended (HFS+)
    • Reinstall OS 9
    • Update to 9.2.2: Mac OS 9: Available Updates
    • Update your firmware
    Install Panther OS X 10.3.9
    • Boot from the 10.3.x install CD 1
    • Go to Installer Menu and open Disk Utility
    • (Optional)Go to File menu and Repair OS 9 Permissions!
    • Quit Disk Utility.
    • Launch Installer
    • Select Destination disk for installation
    • Click Options
    • Select Installation Option Archive and Install
    • (Optional) Preserve Users and Network Settings
    • Choose to Customize and deselect Foreign Language Translations and Additional Printer drivers.
    • Check box to install BSD Subsystems (Panther & earlier).
    • Install Mac OS X 10.3.x
    • Restart and Repair permissions (Applications > Utilities > Disk Utility)!
    • Download and apply the 10.3.9 Combo Update
    • Restart and Repair Disk Permissions as previously!
    • Run Software Update and apply all updates available
    • Repair Disk Permissions (Applications > Utilities > Disk Utility)!
    cornelius

  • Problem: installed new hard drive but can´t boot from leopard dvd

    So I just installed a new hard drive in my ibook G4. At first I started up the computer using the leopard DVD I had purchased. Got to Disk Utility and after a few seconds in the spin wheel came up and froze. So, I shut the computer down and when I tried to boot it again from the DVD I wouldn´t even reach the apple screen. Tried it a few times unsuccessfully.
    As an alternative I just tried booting the comptuer using the original CD and it did read it.
    I am currently at the installer page but I am concern about installing the old CD as I really would like to run the leopard dvd 10.5.
    Is it that my ibook g4 can´t be booted from leopard dvd?
    Please advise. thanks!!

    OK, so I decided to leave my computer resting all night and give it a new try this morning.
    This morning I was able to boot from the Leopard DVD, so I don´t really think it is a problem with my superdrive. Started to format at 32 minutes to complete. Then towards the 10th minute the spinning wheel appeared, I heard the fan running, then it stopped and then I heard the superdrive making some reading noises. Then all noises stopped and now the spinning wheel continues..not sure what to do now.
    In the meantime, I wanted to share also another problem that I´ve been having for quite some time which I don´t know if it is related to my current problem. It is with the computer power:
    - I´ve been experiecing load surges that take my computer from 100% to 1 or 0% and then goes to sleep or shuts down. The same thing happens when I am charging the computer.. it starts charging and showing 2 or 3% charge and then jacks up to 100% in minutes.
    - My computer also makes like a slight humming noise sometimes when the ring around the power cable is in orange color, so I move it around until it stops. When I do that sometimes it goes from orange to green eventhough it is not fully charged. There has been times that under green it appears to be charging (battery charging icon on desktop shows up), and other sometimes like right now when it is in green color and the battery icon on the desktop says ´99%´. Weird enough, once I get the cable in a certain position it enables the battery to charge, if I keep it without moving it, the load surges disappear (at least for some days).
    Should I try resetting the PMU? I´ve not done it because I don´t know what consequences it may have.
    NOTE: When I bought the computer I never calibrated my battery because I was (and still are) clueless when comes to computer technicalities. I tried using a different power adapter and get the sample problem.
    Below is the information I get from coconut battery:
    My battery is in its 256 load-cycle. current battery capacity 58512mAh (original battery capacity: 4400 mAh).
    The last system profiler I was able to pull shows:
    Battery Information:
    Charge Information:
    Charge remaining (mAh): 58320
    Charging: No
    Full charge capacity (mAh): 58512
    Health Information:
    Cycle count: 256
    Battery Installed: Yes
    Amperage (mA): 0
    Voltage (mV): 16250
    System Power Settings:
    AC Power:
    System Sleep Timer (Minutes): 15
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 15
    Dynamic Power Step: Yes
    Reduce Processor Speed: No
    Automatic Restart On Power Loss: No
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Wake On LAN: Yes
    Wake On Modem Ring: Yes
    Display Sleep Uses Dim: Yes
    Battery Power:
    System Sleep Timer (Minutes): 5
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 5
    Dynamic Power Step: No
    Reduce Processor Speed: Yes
    Automatic Restart On Power Loss: No
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Wake On Modem Ring: No
    Display Sleep Uses Dim: Yes
    Reduce Brightness: Yes
    Hardware Configuration:
    Clamshell Closed: No
    UPS Installed: No
    AC Charger Information:
    AC Charger (Watts): 26
    Connected: Yes
    Charging: No
    Any help is greatly appreciated.
    Thanks a bunch!!!

  • Help: Major problem installing a 2nd drive (SSD) in 2011 i5 Mac Mini

    I've installed an Intel 520 SSD in the second bay in my mum's 2011 Mac Mini. I used OWC's kit and the installation went well.
    For two days now I have tried cloning over the OS from the HDD to the SSD but I can't get the computer to boot from the SSD. I cloned using both SuperDuper and CCC. Initially I had problems getting the cloning operation to complete but I suspect that was because I forgot to turn off Spotlight on the SSD before cloning.
    Once I managed to clone the HDD (with SD), I can select the SSD under Sys Prefs - Startup Disk but the system won't boot from it. I notice this because after a reboot About this Mac reports that the HDD is the boot disk even though I selected the SSD. At the beginning of the boot, sometimes the apple symbol (on the grey) screen flickers a few times between the apple and the circle with a diagonal line through it, which I take to mean that the SSD isn't ok. Then the computer defaults to the HDD instead.
    Also, if I click Option to get the boot menu on startup and select the SSD, I will only get a grey screen with the apple symbol and the spinner. I can leave this for ten minutes without the system booting fully.
    I ran AHT (normal, not extended) but no problems are reported. Disk Utility reports no errors on the SSD.
    Then I reset PRAM and suddenly the computer booted from the SSD. Hurrah I thought, but then, equally suddenly, it failed to do so, defaulting to the HDD.
    Could it be that the Mini can only boot from one of the drive bays?
    Or is my SSD faulty? - does Intel have a special diagnostics tool perhaps? I found this page about some bug between SF2281-based drives (like the 520) and an Nvidia chipset but I'm not sure that applies to the 2011 Mini.
    I'm a bit at a loss here so would appreciate some help.
    Thanks very much in advance
    Philip

    pullman wrote:
    First -254 which happens right away. From googling a bit I've discovered this may have to do with having chosen the drive as opposed to the volume as source/target.
    So selecting these (but being confused as to how the recovery partition could be included in the restore if I choose only the boot volume and not the boot drive) the restore began. However it stopped after a few minutes complaining about an "input/output error". No further information given.
    Sorry, my instructions may have been too vague. Yes, when you boot into the Recovery HD on your internal HD and use the Disk Utility Restore you need to specify the Source and Destination as a volume (e.g. Macintosh HD). Don't select the drive. And make sure the SSD is formated correctly.
    With Disk Utility's Restore it does a block level copy so it's like creating an "image" in the PC world (e.g. Norton Ghost or Acronis True Image). This means you get ALL visible and hidden partitions copied over and bootable. With CCC you get a bootable clone of your OS/Apps/Data, but you can't boot to a Recovery HD on that clone. There is none. So, when you clone back to an internal drive, CCC has the Disk Center feature to create a Recovery HD on your internal drive. Disk Utility's Restore, however, clones both OS/Apps/Data and the Recovery HD to your internal drive without having to execute a 2nd step.
    Which Intel 520 Series SSD did you install? I have an Intel 520 Series 120GB SSD installed in my Mac Mini in the bottom slot (closest to the bottom opening) and my stock 500GB HDD in the upper slot (in the drive bracket).

  • Problems installing amd drivers on HP Dv7 for windows 10

    I have the HP DV7 4263cl with switchable graphics AMD chipset M880G with both Mobility Radeon HD 4250  and AMD 6370m. My processor is the AMD Phenom II.  The drivers on HP's support site for my laptop are very old (2010) and work fine in Windows 7. However when I try to install the drivers in compatability mode on in Windows 8.1 or 10 or manually install them through the device manager, my computer does not respond well and doesnt install everything fully and either shuts down or shows a blue error screen.
     I have tried everything and haven't had any luck getting these installed.  Please Help!!!! 

    Yours is the third post I've seen about switchable graphics not working in Windows 10. Sadly, you may have to simply hope for a Windows 10 driver update. Have you checked for a Chipset or BIOS/UEFI update? Maybe you would have better luck on the AMD forum.   If you found my answer helpful please say thanks by clicking on the Thumb's Up icon. Thanks!

Maybe you are looking for