Problem installing Ti4200 with k8t neo

Hi Guys, I just upgraded my motherboard and processor and everything's fine until i try and install the drivers for my gfx card. As soon as i reboot i'm lucky if it stays on for a minute, either the computer reboots as soon as windows loads or it'll stay on for at best a minute then lock up and then reboot a few seconds later. When it comes back i get the message that windows has recovered from a serious error caused by the nvidia drivers and that my card was unable to complete a draw operation. I uninstall the drivers and everythings fine again.
I've tried the card in another machine and it seemed fine. After reading the board i'm guessing its my 12v line that just isn't up to it. I tried unplugging all my drives except for my main HD but still get the exact same problem.
I've run memtest and that seemed fine, every thing in my pc has the latest drivers installed(haven't installed service pack 2 because this was causing it to lock up but i'm guessing this was just because the card drivers were getting installed at the same time).
I just wanna be sure i've tried everything before i go spending £50 on a power supply i might not need. Any ideas?

Quote
Originally posted by ste
Hi Guys, I just upgraded my motherboard and processor and everything's fine until i try and install the drivers for my gfx card. As soon as i reboot i'm lucky if it stays on for a minute, either the computer reboots as soon as windows loads or it'll stay on for at best a minute then lock up and then reboot a few seconds later. When it comes back i get the message that windows has recovered from a serious error caused by the nvidia drivers and that my card was unable to complete a draw operation. I uninstall the drivers and everythings fine again.
I've tried the card in another machine and it seemed fine. After reading the board i'm guessing its my 12v line that just isn't up to it. I tried unplugging all my drives except for my main HD but still get the exact same problem.
I've run memtest and that seemed fine, every thing in my pc has the latest drivers installed(haven't installed service pack 2 because this was causing it to lock up but i'm guessing this was just because the card drivers were getting installed at the same time).
I just wanna be sure i've tried everything before i go spending £50 on a power supply i might not need. Any ideas?
Hi...I having Microstar GeForce4Ti4200 128MB DDR SDRAM AGP TV-Out DVI Retail version and i can´t get my new computer to start and showing anything at all on my monitor, only "invalid sync" is coming up on the screen and that´s it, i cant get any picture at all on my screen, did you have any problem with that? i allso wondering if the voltage can be wrong ( 3.3v) if so...my motherboard doesnt support 3.3v only 1.5v if i have understand this correct. I have try anything to get this brand new computer to start so i can get into the bios and making my settings, i have try to reset cmos and allso remowing the battery but nothing helps. The only that helps are to buy a newer video card with 1.5 voltage onboard.

Similar Messages

Problem install PSE11 with a MAC OS disc on MACBook Air

problem install PSE11 with a MAC OS disc on MACBook Air I've done the serial number, adobe ID, Option and now install "installation Progess" with a message Please close all of the following applications to continue: Adobe Bridge CS4, Photoshop Elements (Adobe Photoshop elements) I've checked to insure those are closed. Yes they are close - press "continue" but nothing happen. HELP!

Look in Activity Monitor (Applications>Utilities) to see if there are any adobe processes still running somewhere in the background.
(Incidentally, just in case you're a new switcher--closing the window doesn't normally close the program on a mac, unlike windows. You must still quit the program itself.)

Help! XP install problems with K8T Neo-FIS2R

The other day I put together a new system for a friend. I got the system to POST properly, the diagnostic lights on the D bracket are fine, and I can edit the BIOS, and the BIOS sees all the drives properly.
However, installing XP Pro has been impossible. I set the system to boot first to the CD, then to the hard drive (from the BIOS). After booting to the CD, I never see the message I am used to seeing ("Press any key to boot from CD...) when booting from the XP Pro install disk. The system thinks about things for a long time with a blank screen, then later it finally begins to do the install. Things appear normal at this point as in any other time I have installed XP Pro. I reformat the hard drive to start clean and then the XP install files are copied over. I get the standard message that the system will reboot and this is where things get flaky. The system reboots, but I never get the message once again on whether or not to boot from the CD. So after a while the system tries to install XP once again (it would repeat this process forever....trust me). I've popped the CD out right after the system reboots so it will try to go to the hard drive. I just get some kind of boot failure message and to insert the bootable media or whatever. I've even gone into the BIOS right after the reboot to switch the BIOS loading to try and load the hard drive first. This still doesn't give me the desired results.
This is by far the weirdest thing I've ever experienced when doing an install. I've installed XP Pro on at least 15-20 desktops/laptops of different configs and never ran into this before.
The BIOS settings are stock. I didn't see anything in there that was really needed tweaking or that hadn't "set itself". I haven't messed with the SATA or RAID stuff since it's not really necessary in this situation.
Here are the system specs:
--Antec 430 True Power PSU
--K8T Neo-FIS2R mobo
--AMD 3000+ 64 bit CPU
--40GB Maxtor HD (master on IDE1)
--Lite-On DVD-ROM drive (slave on IDE1)
--80GB Western Digital (8MB buffer) (master on IDE2)
--Sony DRU510A DVD-RW (slave on IDE2)
--(2) Kingmax 184 Pin 512MB DDR PC-3200 Model# MPXC22D-38
--ATI 9800 Pro
--3.5 Floppy
All the components except the mobo, CPU, and memory are from another AMD system that was running fine. No problems with any of the HD's or the optical drives. All new components were purchased from newegg.
I thought that maybe I had a problem with the jumpering of the drives so I messed with those in about every possible combination. I took IDE2 completely out of the system and just tried to get it running with the 40GB Maxtor and the Lite-On drive. I tried about every master/slave/cable select combination but nothing was working. In certain combinations the BIOS recognized everything as I intended. I've pulled everything off that doesn't need to be connected. Keyboard, monitor, and internal components are the only things connected.
I don't consider myself to be a guru at this business, but I can get through most things with enough trial and error. This really has me stumped.
Any help is certainly appreciated.
Thanks,
Heath

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Download the drivers from MSI again, and when you copy the contents of the XP folder to floppy ADD the file txtsetup.oem from the directory above that folder. Worked for me..!
Ian

Early Chipset Initialization problem with K8T Neo 2 - FIS2R

This one has me stumped.
I went to install a new CPU fan earlier today and while I was installing the fan I had to remove my sound card and AGP card so I could screw the fan to the side of the heat sink.
I got all that done and went to start the computer back up and now I get a contineous high pitched sound while at the same time 3 beeps. The D bracket shows a green LED on 1 so this is the "early chipset initialization" problem.
What is causing this and why would this happen after a fan installation?
Specs
A64 3200+ Winchester
1.5 GB RAM (2x 512, 2x 256) DDR 400
MSI K8T Neo 2 - FIS2R
PNY GF 6800
Audigy 2 ZS Gamer
200GB IDE HDD
80 GB IDE HDD
DVD - R/RW
Win XP Pro w/ SP2

Okay after a bit of messing around with the problem I discovered what the problem was....
I didn't plug in the power to the video card
Yeah the 6800 uses needs more power from the PSU and I left that little rail unplugged. Maybe some other soul will find this useful in a time of need.

Boot and OS install issues with K8T Neo2 F

Can anybody shed light on my difficulties?
Assembled a new computer yesterday. First power-on produced nothing except 3 (2,3,4) red leds on d-bracket. After reading several postings, tried the following:
Swapped around memory modules;
Did repeated JBAT1 data clears (NB if you happen to get a board with the V1.0 user guide, note that the JBAT1 diagram appears upside down - pin one is closest to the SATA slots (page 2 - 24). The MSI downloadable user guide (V1.2) has that error corrected (page 2-25)
The only memory config that doesn’t produce three red leds is with one 512 stick installed in channel 3 (green).
Can now get to the point where Windows XP boots to the point where install is about to start, and then advises me that it can’t find a hard disk!
Have dis/reconnected the sata cable (using different cables) and checked the bios setup but can find nothing strange except that setup refers to the hard disk as BBS 0 (RAID) ST3120827AS - the reference to “RAID” worries me.

Paul, there have been people here that have had to strip their system down to the bare minimum hardware to get windows to complete the install, so try that. I had trouble completing my windows install as long as I was trying to install the RAID drivers at F6. So I ignored the prompt at F6 and windows installed fine. Then I installed my RAID drivers afterward.
These things are extremely sensitive when it comes to memory. I had the same problem you are having. Mine was cured by a BIOS upgrade to ver. 3.3. The simplest way to do it is to use "Live Watch". It will locate BIOS ver 3.3 for you, and download it to a floppy along with the flash program, and make it bootable all in one easy step. Then all you have to do is boot from the floppy you just made, and follow the instructions. Very simple.
I've read all these stickies and posts now going way back, and IMHO anyone who wants to use RAM thats not on the list should do so at their own risk. Interestingly enough, the recommended list from MSI is not the same as the list from AMD. And the memory manufacturers have their own lists of RAM that they say will work with this board. I'm using 2x 512 sticks of GEIL from the MSI recommended list.
Check out these links to see what I mean. By the way, if you haven't noticed, most of the older posts about memory problems are with respect to the K8T Neo FIS2R which is a socket 754 single channel board, so although they are similar, they're not the same. My point is just because his K8TNeo FIS2R works fine with brand "X" RAM doesn't mean your K8T NEO2 FIR will.
http://www.msi.com.tw/html/products/mainboard/testreport_pdf/6702E/memory.pdf
http://www.crucial.com/store/listparts.asp?Mfr%2BProductline=MSI+%28Micro+Star%29%2B+Motherboards&mfr=MSI+%28Micro+Star%29&cat=RAM&model=MS-6702E+%28K8T+Neo2-FIR%29&submit=Go
http://www.mushkin.com/epages/mushkin.storefront/EN/product/991140
http://www.amd.com/us-en/assets/content_type/DownloadableAssets/Athlon_64_Unbuffered_DIMM_AVL.pdf
http://www2.amd.com/us-en/Processors/TechnicalResources/1,,30_182_869_9460%5e9461,00.html?1094454813
Good luck!

PC with K8T Neo stopped powering up

Hello,
I built a pc with MSI K8T Neo motherboard, Athlon 64 3200+ processor, 1 Gig (2 x 512) Kingston value PC3200 RAM, ATI Radeon 9600 XT with 128 RAM, Maxtor 80 gig hd in a PowMax case with 400 W power supply. I installed Window 2000 on my machine with no problems. After I installed the video driver (3.10) the machine told me to reboot, which I did. However, the machine did not power back up and did not turn on through the power button. I used a volt meter to test both the power supply and the power button -- both work. I also took out the battery on the motherboard to reboot CMOS to no effect. I am starting to think that the problem could be with the motherboard but I am not sure.
Thanks for any advice.

did a cord maybe come loose or something?
this is the wierdest problem i have heard of so far...

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

High frequency sound with K8T Neo-FIS2R

Hello!
I have the MSI k8t neo-fis2r mainboard with bios v 1.6 and sometimes it makes a horrible high frequency sound and I cant figure out why.
My system are:
amd 64 3000 cpu and
Corsair Value S PC3200 DDR-DIMM 512MB Unbuffered, Non-parity, 64Megx64, CL2.5
My other components does not cause the sound (that I have found out by testing).
I wonder if the ram causes the sound? Can you please help me. The sound is so bad that I cant use my computer. It only appers during heavy system load, and not in windows. It has nothing to do with my video card (because I have tried with several different cards). My bios settings are default values + cool and quit enabled. I have the core center installed so the progam controls the cpu fan.
I really hope someone can help me.

The sound does not come from the speaker and I dont think it comes fom the cpu fan either. I think it comes from the motherboard, ram or the cpu. When I dont use my mouse it is quit but when I clik it makes this sound. Can it be that I have to set all values in bios for ram etc. manually instead of automatic?
When it comes to other electrical sources I have a TV standing 0.5 meter from the computer. Could thins cause the problem? I did not have the problem with my old motherboard which was a MSI K7T Turbo2.
The sound usually appers when I am benchamarking my system. For example 3dmark 2004. Because of this I thougt there was a problem wiht my vga card but after a changed to a new one...the situation was just the same.

Booting "issues" with K8T Neo-FIS2R

Well hello everyone. First of all I want to say that my English isn't completely error-free and my problem might seem awkward because of my ways of expression.
I also want to say that i've read alot of threads and searched the forum for my problem.
For a couple of days ago I got all my parts for building my 64bit-system and I build her up. To my suprise it booted, with almost no errors. Although I could install Windows XP and use it completely, everytime I boot it (under the booting sequence) it says "Bios is not installed", although I can enter bios simply (like everyone else) just pushing the DEL-button.
But this isn't the only problem. When I enter PC Health Status it says that the cpu is running at whooping 62-65 degrees. When i have my hand around the cpu-cooler it doesn't even feel warm so I think it has something to do with my BIOS-version that i am running now (Yes, I've read that in much more threads)
Also I have problems using the Cool'n'Quiet technology. I have it supported in the BIOS and activated it although it will not work (maybe it has something to do with the bios?) With this i mean that i will not go underclocked (It's allways 2.2 GHz)
My final problem is that it sometimes takes the system 2 minutes to boot sometimes, it happend after i flashed the bios to 1.7 from 1.0
Under these circumstances I've used 1.0 AND 1.7 BIOS-versions.
I've never overclocked the computer either.
What could be wrong?
I'm using 3200+ 2.2GHz Athlon 64 cpu.
K8T Neo-FIS2R
Radeon 9800pro
Seagate 7200.7 200GB drive.
380W Antec PSU.

Quote
Originally posted by $post[username]
I've tested notebook, minial power savings and battery. C'n'q still doesn't seem to work. Yes i've enabled it in bios. I downloaded the AMD Athlon™ 64 Processor Driver for Windows XP, Version (zip) 1.1.0.14 -
Yesterday my CnQ began to work fine. I've done the same as you:
1- Enable CnQ Bios option
2- Install the AMD athlon64 driver for XP
3- Set "minimal power savings" at windows xp energy options
I have installed the CoreCenter 1.6.8.0 (is the last version) utility, and I've set enable the CnQ in this application. You'll can see that the CPU velocity change "on demmand" and the CPU fan too.
Of course, I've the last VIA 4in1 drivers, 1.7 Bios ver. etc
My temp & MHz values are:
~40ºC ~ 800 MHz idle
~50ºC ~ 2000 MHz playing or that kind of stuff
Note that the PC case is open, because the PC is under my table and there is no good ventilation.

Help with K8t Neo-2 F memory config...

Hi all, ive been looking for a solution to my problem and cant figure it out...I have a k8t neo-2 f and i cant set up my mobo to run in dual channel mode...if i put all 1gb of my ram in 1+2, then no problem, but as soon as i go 1+3 or 2+4 then the computer turns on but doesnt beep, no display...no nothing. The usb diagnostic thing on the pci slot has lights that suggest its in "early chipset initialization", but it goes no further than that. Initially i was using two unmatched pieces of ram and thats when i realized that wouldnt work at all in dual channel mode. So i shelled out the cash for OCZ matched ram 2x512mb and that does not work either.....worse yet is im running windows x64 and have a scsi HD, and cant figure out how to flash my bios, dos diskettes tell me c: is invalid(tried to update bios via MSIs dos method), and live update 3 doesnt work on x64. So my question is...am i doing something wrong here, and if it is bios update related....any ideas on how to go about updating it...last i checked the bios was v3.3....any help or suggestions would be greatly appreciated, in the mean time im going to try to put windows xp on and try to flash the bios with live update...and see if that works...i dont know why v9 would solve it, but im desperate now and really am ready to try anything! thanks in advance, sorry in advance if this is an old issue or if someonelse has already had it, i searched and searched only to find somewhat similiar but not identical problems...
update: looks like v3.3 is the newest one, i cant seem to get live update to show me v9...saw the stick on 9.1....but cant get it to flash...
arjun

Yeah, thanks Tiresmoke. I built the PC in my sig from some old and new parts, realised the mobo wouldn't work with 1xGB double sided and 2x512mb single sided RAM. Bought another 1gb stick, the two sticks together wouldn't work...
Signed up to this forum, and within a minute or two found this thread and a solution - the 9.1 BIOS. Fifteen minutes later (after installing a floppy drive... ) Fixed.
Thanks.

Need help with k8t neo ms-6702 and cpu compatiblility question.

I have a msi k8t neo motherboard socket 754 ms-6702 bios version 2.2 with a athlon 64 2800+ in my computer. I just bought a AMD Athlon 64 3700+ CPU Socket 754 .1MB cache. When i install it, my power goes on and i get no activity. Im wondering if i got a bad cpu off ebay or my bios isnt current enough ( i used msi live updating software and its currently at v 2.2) or does my motherboard not support this high of a cpu? Im not very computer literate. Thanks for any help and info. If i need to update my bios, i downloaded version 7.1 but i dont know how to flash it, can somone give me the steps

I had a bad experience with a 3700 bought on e bay ,turned out to be an engineering sample ."special m/b bios reqd" in my case I did get a boot and the engineering cmos message. genuine 3700 754's are quite rare and fetch premium prices.

Mobile Athlon 64 3700+ Compatible with K8T Neo?

I've been thinking of installing a larger cpu in my mainboard, the current set-up is...
MSI K8T Neo with AMD Athlon 64 2800+
I know that the Athlon 64 3700+ is compatible but is the Mobile Athlon 64 3700+
As far as I can tell all the specs look ok, it's just the mobile bit that worries!
Any ideas?

To quote Richard: "Any S754 cpu will work on a S754 board".

Problem after CMOS reset K8T NEO FIS2R

Hi,
After messing around with my memory timings, I could no longer boot my system, so I decided to reset my CMOS using the jumper. After doing so, my system gets stuck at the SATA drives not detected BIOS not installed screen, and I can no longer access the BIOS. I'm fairly sure that the BIOS not installed message is in reerence to the SATA controller and not the main BIOS itself. I have tried reseting the BIOS a couple of more times with no different results. My D-Bracket reads red LED in location 1, green LEDS in 2, 3 and 4.
System:
Athlon 64 3000+
K8T NEO FIS2R
Radeon 9700 pro
Audigy 2 ZS
400W PSU
Any ideas would be welcome.
Thanks

Hi
Try removing the Ram sticks when resetting Bios, remeber to earth yourself first, also remove power cable, and leave for a couple of minse, to allow all chips to discharge, then replace mem sticks, the cmos jumper and the power cable. Try to get into bios at start to reset the timings you have changed. If still having a prob, use Ctrl + Home as you boot, holding them down will initialise the bios. You will have to reset the bios settings.
Failing that you will need to use a recovery floppy.
Good luck
jocko

Problem installing apps with iTunes!

Hello!
I have a big problem.I can't install apps using iTunes,because it shows me a message saying that the computer isn't authorized.But it is.Even after authorizing again,it shows the message again.If i install apps with appstore on my iphone,they work but as soon as i sync it with itunes the aplications stop working,i'm guessing because they aren't authorized.I tried everything,restoring my iphone,reseting it,uninstalling all my apple software and nothing.What should I do?

Try these steps:
The following steps will recreate the SC Info folder if it is unusable.
Windows Vista or Windows 7:
1. Open Computer from the Start menu.
2. From the Organize menu, choose Folder and Search Options.
3. Click the View tab.
4. In the "Advanced settings" pane under "Hidden files and folders," make sure that the "Show hidden files and folders" option is selected.
5. Click OK.
6. Navigate to the following location by either typing it into the address bar, copying and pasting it into the address bar, or clicking through the folder hierarchy listed:
C:\ProgramData\Apple Computer\iTunes
7. Right-click the SC Info folder shown and on the shortcut menu, choose Delete.
8. Restart the computer.

Problems installing Axis with WLS 8.1

I'm having problems installing Apache Axis with WLS 8.1.
I'm totally new to WLS, so this may be at the heart of the problem.
I install Axis as per the installation instructions.
These are the steps I followed:
1. Installed the axis directory to
C:\bea\weblogic81\samples\domains\examples\applications\axis2. Added xml-apis.jar and xercesImpl.jar to the AXISCLASSPATH ( the complete AXISCLASSPATH is
C:\axis-1_2RC2\lib\wsdl4j.jar;C:\axis-1_2RC2\lib\axis-ant.jar;C:\axis-1_2RC2\lib\commons-discovery.jar;C:\axis-1_2RC2\lib\commons-logging.jar;C:\axis-1_2RC2\lib\jaxrpc.jar;C:\axis-1_2RC2\lib\log4j.properties;C:\axis-1_2RC2\lib\log4j-1.2.8.jar;C:\axis-1_2RC2\lib\saaj.jar;C:\axis-1_2RC2\lib\axis.jar;C:\javasoft\javamail-1.3.2\mail.jar;C:\javasoft\javamail-1.3.2\lib\smtp.jar;C:\javasoft\javamail-1.3.2\lib\mailapi.jar;C:\javasoft\javamail-1.3.2\lib\pop3.jar;C:\javasoft\javamail-1.3.2\lib\imap.jar;C:\javasoft\jaf-1.0.2\activation.jar;C:\javasoft\Xerces\xerces-2_5_0\xercesImpl.jar;C:\javasoft\Xerces\xerces-2_5_0\xml-apis.jar)3.Added weblogic.xml file to C:\bea\weblogic81\samples\domains\examples\applications\axis\WEB-INF\weblogic.xmlas per instructions with <prefer-web-inf-classes>true</prefer-web-inf-classes> 4. Started the examples server.
5. I then tried to validate the installation as per intructions using <a href="http://localhost:7001/axis"></a>
Everything looks OK with the Axis start page displayed.
6. I then tried happyaxis.jsp . All needed components are present with saaj.jar being picked up from :
Found SAAJ API (javax.xml.soap.SOAPMessage) at C:\bea\weblogic81\samples\domains\examples\examplesServer\.wlnotdelete\extract\examplesServer__appsdir_axis_dir_axis\jarfiles\WEB-INF\lib\saaj.jar7. I'm missing optional component xmlsec.jar
8. Now the trouble starts!!!
pretty much anything I try now comes back with:
AXIS error
Sorry, something seems to have gone wrong... here are the details:
Exception - java.lang.NullPointerExceptionI get this if I try:
<a href="http://localhost:8080/axis/services/Version?method=getVersion"></a>
or
<a href="http://localhost:7001/axis/services/AdminService?wsdl"></a>
or
<a href="http://localhost:7001/axis/services/Version?wsdl"></a>
So, what's going wrong? I cant think what to do next. Please help! I need this to work fairly urgently.
Nigel
PS. here's the NP exception in detail
java.lang.NullPointerException
        at weblogic.xml.jaxp.ChainingEntityResolver.popEntityResolver(ChainingEn
tityResolver.java:61)
        at weblogic.xml.jaxp.RegistryDocumentBuilder.setEntityResolver(RegistryD
ocumentBuilder.java:168)
        at org.apache.axis.utils.XMLUtils.releaseDocumentBuilder(XMLUtils.java:2
35)
        at org.apache.axis.utils.XMLUtils.newDocument(XMLUtils.java:312)
        at org.apache.axis.utils.XMLUtils.StringToElement(XMLUtils.java:485)
        at org.apache.axis.AxisFault.addFaultDetail(AxisFault.java:654)
        at org.apache.axis.AxisFault.addHostname(AxisFault.java:888)
        at org.apache.axis.AxisFault.addHostnameIfNeeded(AxisFault.java:877)
        at org.apache.axis.AxisFault.initFromException(AxisFault.java:280)
        at org.apache.axis.AxisFault.<init>(AxisFault.java:181)
        at org.apache.axis.AxisFault.makeFault(AxisFault.java:101)
        at org.apache.axis.server.AxisServer.generateWSDL(AxisServer.java:487)
        at org.apache.axis.transport.http.QSWSDLHandler.invoke(QSWSDLHandler.jav
a:62)
        at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
        at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
        at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
        at java.lang.reflect.Method.invoke(Method.java:324)
        at org.apache.axis.transport.http.AxisServlet.processQuery(AxisServlet.j
ava:1132)
        at org.apache.axis.transport.http.AxisServlet.doGet(AxisServlet.java:233
        at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
        at org.apache.axis.transport.http.AxisServletBase.service(AxisServletBas
e.java:301)
        at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
        at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run
(ServletStubImpl.java:1006)
        at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
pl.java:419)
        at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
pl.java:315)
        at weblogic.servlet.internal.WebAppServletContext$ServletInvocationActio
n.run(WebAppServletContext.java:6718)
        at weblogic.security.acl.internal.AuthenticatedSubject.doAs(Authenticate
dSubject.java:321)
        at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:
121)
        at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppSe
rvletContext.java:3764)
        at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestIm
pl.java:2644)
        at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:219)
        at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:178)

I'm doing exactly the same thing (adding the xerces jars to my web-inf/lib), but happyaxis.jsp is saying the jar I'm using is invalid as follows:
Error: Invalid version of SAAJ API found in D:\bea\weblogic81\server\lib\webservices.jar. Make sure that Axis' saaj.jar precedes D:\bea\weblogic81\server\lib\webservices.jar in CLASSPATH.
Axis will not work.
Maybe this worked in a previous release/SP? I'm using 8.1SP3. I've read some other post saying you cannot override stuff in the weblogic.jar, so I've tried to add the jars to the pre_classpath, which resolves the issue but I get a soap fault related to this thread. Any ideas?
Thanks,
Lou
My weblogic.xml looks as follows:
<weblogic-web-app>
<jsp-descriptor>

<jsp-param>
<param-name>jspServlet</param-name>
<param-value>weblogic.servlet.WlwJSPServlet</param-value>
</jsp-param>
<jsp-param>
<param-name>debug</param-name>
<param-value>true</param-value>
</jsp-param>
</jsp-descriptor>
<container-descriptor>
<prefer-web-inf-classes>true</prefer-web-inf-classes>
</container-descriptor>
<url-match-map>
weblogic.servlet.utils.SimpleApacheURLMatchMap
</url-match-map>
</weblogic-web-app>

Problem installing Ti4200 with k8t neo

Similar Messages

Maybe you are looking for