Problem k8n neo platinum

hi everyone
I got one problem. I just installed msi k8n neo platinum and flashed the bios from 1.4 to 1.6. The problem is when I want to change HT frequency there was no number in the menu and my pc stucked there. The worse is I cant go over 205. . As I know this mobo is good for overclocking butthis one is really suck. Anyone can help me? ( ignored the grammar). btw I used 3200+ Newcastle, 2x512 corsair xms

I suggest you go back to Bios 1.4 and see if everything works.
If everything is OK then either the Bios 1.6 sucks or you did not update properly.
MSI is good in reverse engineering, I upgrade my Neo4 from Bios 1.2 to 1.4 and I got stuck!!

Similar Messages

USB mouse problem - K8N Neo Platinum

I have a Razer Boomslang 2000 USB mouse. Ever since I got my new motherboard, the K8N Neo Platinum, It has problems when i turn the power for a long time - overnight. When I turn it back on in the morning the mouse refuses to work. I then have to manually pull it out of the USB port and plug it back in, in order for it to work. This is extremely frustrating.
I have windows xp pro sp1 all fully up-to-date and the latest 1.2 bios and 5.03 chipset drivers.
Any ideas on how I could fix this ??
System
AMD Athlon64 3200+ Newcastle
MSI K8N Neo Platinum
1 GB Corsair XMS 3200 LL @ 11, 2, 2, 2T
ATI Radeon 9800 Pro w/ VGA Silencer @ 461/371
Seagate Barracuda 120Gb sata
Windows XP Pro SP1

Hi Dread,
I also have this problem with the same motherboard as you. This was the case with my K7N2 DELTA as well. Solved the problem by using an USB - PS2 adapter.
Regards,
Andrew

Post problem with K8N Neo Platinum

I am assembling a system for a friend and it hangs according to D-Bracket2 on Processor initialization (Led 1:red, led 2:green, led 3: green led 4: red)
Specs
PSU: Codegen 350W ( 3,3V 14A
5V 30A
12V 15A )
VGA: Sapphire Radeon 9800 Pro 128MB
CPU: AMD Athlon 3000+
HDD: Seagate 7200.7 120GB in SATA1-port
DVD: MSI DR8-A DVD Burner
RAM: M-Tec 512MB DDR400
If the problem is the processor it should hang on Power On (all leds red), right?
There's some damage done to CPU fan connector so the sensor wire from the CPU fan might have no connection to the mobo. How about ESD-damage, can it cause this?
Another thing I might have done wrong is connecting front panel connectors.
I am just hoping and praying that the processor is OK and the mobo causes this.

Thanks to RacerX for answering but the problem wasn't the PSU.
Mobo caused it and I replaced it. I think it was the physical damage I mentioned in the first post. I also changed hdd from SATA1-port to SATA3-port but I don't think it matters.
Now everything works fine so +12V/15 Amps is enough.
Does the K8N Neo Platinum hang on Processor Init if it doesn't detect CPU Cooler?

Problems with 64 3200+ on MSI k8n neo platinum.

AMD Athlon64 Newcastle 3200+ AX 2200MHz/2.2GHz 512kb Boxed (with cpu-cooler!) Socket754
MSI K8N Neo Platinum nForce3 250Gb 3DDR-DIMM 5PCI SATA Raid Audio GB-LAN Firewire Socket754 ATX
Kingston KVR400X64C3A/512 512Mb DDR PC3200 400MHz 184pin Unbuffered CL3
Okey here it comes..
I installed everything and all seemed to work okey, until i threw in the XP install cd and began my install..
in the dos install of windows xp, (when it moves files to the hdd) it stopped and said that there was a problem with a file that were to be copied, i pressed enter to try again and the install moves on, this accurs 4-5 times and then it gives me a BIG "IRQL less or not equal".. Blue screen of death.. (it complains on different files each time i try to install xp, tried 15-20 times)
I have tried to change memory to another Kingston KVR400X64C3A/512 512Mb DDR PC3200 400MHz 184pin Unbuffered CL3 with no luck,
changed hdd, change gfx-card. change psu, removed all no-need pci-cards..
but still same error, i aint no expert so i might have missed something in bios or something :(
please help me if you can..

Flashing bios with memory errors is a veeeeery bad idea .
Almost guarantied to ruin your bios chip with bad data block.
That this even is suggested with mem errors , well .
You need to resolve the mem errors before doing anything else.
The windows xp install routine is a very heavy user of cpu and memory
and will fail if you have mem errors like you have.
Some things to try is entering bios and change auto settings on cpu voltage
giving it 0.5v more than default .
Set the memorys voltage to vendors max approved voltage
which for yours is 2.6v +/- 0.1v . So it's safe to set at 2.7v .
Set timings to cas 3 ,ras 3 ,trp 3 , tras 8 , CMD 2T.
Pushing it firmly down in the dimm socket , sometimes it's not all the way down there even if the plastic lockers snap in.
Disconnect all devices not needed for a windows install ,things can be added later.
Have only the hd that os is to be installed to , one cdrom , floppy , memory and
gfx card .
Disconnect USB case front connector (cause corruption and strange faults if
USBOC pin is connected)

MSI K8N NEO Platinum Edition PROBLEM

Hi (my english is not good sorry for that)
I just got my new computer:
MSI K8N NEO Platinum Edition
AMD Athlon64 3200+
Western Digital Caviar 160Gb
PNY Verto GeForce 6800Ultra 256Mb
1GB Value Select pc3200
Levicom 500W
The Problem is that when i start the computer, it boot and die directly no bootscreen what so ever, it boot and die. i dont know what to do plz help me

Make sure you have Both the ATX Wires on.. theres the Big one! (21Pins i think).. and the Small 4Pin Connector both need to be connected.. if you havent done so yet.. Another thing you could do is Take everything out and place it on a cardboard or something appropriate for the mobo.... I think your motherboard is shorting?.. if it's touching your case.. I had somewhat the same issue long time ago.. give it a try..if you want hope it helps..

MSI K8N Neo Platinum & Crucial Ballistix 512MB RAM Problem

I have had MSI K8N Neo Platinum and 1x Crucial Ballistix 512MB RAM for 11 months.
I have had 1x Crucial Ballistix 512MB RAM for 2.5 months, for a total of two.
I have had MSI GeForce 6600GT (NX6600GT-VTD) 128MB AGP for 1 month.
For about 1.5 to 2 weeks, I have been seeing random crashes while playing PC games.
I started a thread on the Hard OCP forums a few days ago. I did not know MSI had forums =)
Rather than re-typing, I may as well just post the link:
http://www.hardforum.com/showthread.php?t=934956
My issue is also similar to this one:
https://forum-en.msi.com/index.php?topic=83799.0
Thanks for the help.

ALL RIGHT, after almost FOUR months my issue is FINALLY resolved.
It is amazing how much time passes when you are hesitant to buy parts unless you are 95% sure it will fix the problem.
OK, here is an update as to what I remember.
I went to BIOS 1.4 and tried many different physical and BIOS RAM configurations (Different seating, different number of DIMMs, different RAM timings, voltages, etc).
I concluded that I could not make my PC 100% stable, but I could get it darn close. With certain settings, such as DDR400, 2-2-2-6, 1T, 2.80V, Aggressive Timing enabled, Memtest failed test #5 every time (this is spec for my RAM). With other settings, such as DDR333, 2.5-3-3-7, 2T, Auto V, Aggressive Timing enabled, Memtest failed test #5 maybe once out of 5000.
I also concluded that the RAM voltage and Aggressive Timing setting was having a big impact. Some settings would not work (failed Memtest) with RAM at 2.80V but would work with RAM at Auto V. Some settings would not work (failed Memtest) with Aggressive Timing enabled but would work with it disabled.
Finally, I started to occasionally get R,G,R,G (Processor Initialization) on the D-Bracket upon cold-start & warm-start, which suggests a PSU issue:
https://forum-en.msi.com/index.php?topic=76972.msg542545#msg542545
That pushed me over the top, and I decided to buy a new PSU (TG-480-U22) and a new SATA HDD (WD2500KS) just because.
Problem solved. Thanks for all the help.
I will continue to buy MSI in the future just because of these forums…and a good product of course!

Msi k8n neo platinum ps2 keyboard problem

Hi. I'm having issues with my msi k8n neo platinum motherboard. I've read about 50 posts on these forums regarding the supposed ps2 keyboard issues with recent msi boards. However none of them seems to address my current situation.
Like many others, when I power up my system the cpu fan spins for like 3 seconds then everything comes to a halt.
I tried many things to get my system to boot and the only thing that works is plugging my ps2 keyboard into the ps2 mouse port and moving the ps2 mouse into a usb port with an adapter.
It seems there's no hope for fixing the problem other than RMA'ing, but I thought I would add to the pile of complaints stacking up against the MSI boards.

if u had read the threads a little more u might have found a solution that seems to have worked 4 many - a usb keyboard usb Keyboard if u go this route dont forget to enable usb kb in bios
Edit: This Thread Summarises the situation PS2 keyboard/mouse causes random shutdowns or doesnt work

MSI K8N NEO PLATINUM (RAM/HD problem/mobo problem?) [SOLVED]

my setup:
windows xp pro sp2
amd athlon 64 3200+
msi k8n neo plat - 7030 - bios 2.1
x800 xt vid
sound blaster audigy 2
kingston valueram pc3200 2x512 cas 3-3-3-8
ps = antec 430 watt truepower power supply (20 A on 12V)
I dont know if you guys remember my but i created a topic on here a while back about how my keyboard and mouse suddenly stopped working, well that turned out to be that the msi k8n neo platinum just went bad. So i RMA'd it and recently got the replacement board (with latest bios already installed). It worked completely fine for about a day. Well that same day i got it back, i installed a Logitech G7 USB wireless mouse. after i installed it, i began getting numerous windows stop blue screen errrors, even after i removed the mouse from control panel. So i figured i should format because to rule out everything and start fresh. So i did a FULL format and attempted the reinstall windows again. AFTER the format and BEFORE windows attempted the continue installation, i got the same stop error. I figured now this was a hardware problem. So first i tested RAM. I got the latest version of memtest86 and let it run for 4 hours (11 passes) with NO errors at all. Secondly, i got a western digital hard drive diagnostic program to test for failing hard drive and again no problems with that. I still suspected ram so i tried to boot with only 1 stick installed (in first slot), however the PC didnt boot at all (cleared cmos too). So i moved it to the second slot and cleared cmos again and this time it posted but it just hangs at a cursor and does nothing, same thing happened with third slot. I tried this same procedure clearning cmos each time with the second ram stick and got the SAME results. Shouldnt the motherboard boot with only 1 ram stick installed? Did MSI RMA me another bad board? Any help would be appreciated. thanks.

Quote from: russellmrgn on 28-March-06, 10:54:39
Sap147
Can you give us what the D-Bracket was showing ie
R R
G R
As an example this means "Initializing Keyboard Controller"
You will find this information in the manual page 2-23. (On mine) under Hardware Setup
Also can you please do all your tests with the ps2 keyboard and mouse and for now leave your Logitech G7 USB wireless mouse to one side.
Russell
for two sticks of ram = RR
GG
for one stick of ram = GR
GG
as for the g7, it hasnt been plugged in at all, i took it out long ago.. as for the ram, the timing was set to 2T, no overclocking, i will try 2.7 v and let you know, but for the record, it has been running at normal voltage settings for about a year perfectly fine.

MSI K8N Neo Platinum with Vapochill Case problems - Help anyone. :)

Hi all,
Had a bit of a tricky problem and as Im new to this board I have no idea what could be causing this.
First all all system specs:
Athlon 64 3700+ Clawhammer
MSI K8N Neo Platinum -
1 gig Corsair XMS ProL Low Latency Ram (2 x 512mb)
Nvidia Gefore 6600GT
1 x WD Raptor 10000rpm HD
NEC 2500a DVD writer.
Eye-T 550w PSU.
Vapochill SE Case with installed Vapochill Phase change cooling.
Here are photos of it in its present state, you will notice that it isnt installed in the case at the moment.
The reason for that is because the two wont work together and I want them to so so bad...
So, hopefully someone here can save the day for me - here goes.
I have tested the Motherboard and all other componants outside of the case and everything runs smoothly and there are no problems what so ever, great.
I have also retested the Vapochill case with another motherboard and that also works without a hitch.
The problem comes when I insall the MSI board into the system, all hooked with a really basic setup, PSU, Case cooling, CPU and Ram. Flick the on switch on the power suply and the system turns on for around 1/2 a second then turns off again. I found this strange because it soundnt come on at all until I press the power button.
If I press the power button the same thing will happen over and over.
I have tried a different powersupply and this does nothing at all.
I have checked for shorts and there is no possible way it is shorting on anything.
I have a fan plugged in where the CPU fan would go and this doesnt help.
I have taken it back out and tested it again and it still works ok.
Does this sound familiar to anyone? Are there any secret Bio's menu's that would have an option that would solve this?
Any help would be greatly appreciated.
Glenn

When you are running the MoBo standalone, what are you connecting to the Power, Reset, HDD, etc. pins ? Are you using the wires from the Vapochill case, or something else ? It looks like a single cable with an intermittent switch (red/white cable). I once had a similar sort of problem and it was because I hadn't connected up (the incredibly fiddly) cables correctly. Other than that, I would have gone for a short of some sort - but you have checked that already, so . . . .
As to the system starting to power-up when you switch on the PSU, I wouldn't worry too much about this. It seems to happen from time to time with some of my systems - amongst other things, the BIOS can be set to resume to previous state after a power-fail.

K8N Neo Platinum with Venice vcore problem

Hello,
I got a new Socket754 CPU Venice E6 3000+ and replaced it with NewCastle CG 3200+.
But BIOS indicates VCORE is 1.9V+. It's obvious that it's too high and also CPU temp is 0C/32F.
Does anyone know how to fix this problem?
Athlon64 3000+ Venice E6
K8N Neo Platinum (MS-7030) BIOS 2.1
WD Raptor 36GB
Reserator1 Plus
Seasonic S12 500W
ATI Radeon 9800 Pro
SB Audigy2

Please create your own rig and put in your sig with details of PSU and BIOS rev. Have you OC'ing your pc recently?

K8n neo Platinum and Optical Drive problem?

I need some help figuring this out. I've been searching for awhile but can't find any more information so I figured I'd ask here.
I have a Lite on LDW 411s dvd writer that is on the same ide channel as a lite on dvd player (labled as JLMS SJ-HD1665 in the device manager.
The problem is on the 411S where it will read the DVD/CD disk but when I try to use Cyberlink PowerDVD or Nero Recode to play or read the DVD it will just hang. If I don't try to play these files and just open them in explorer then I can access them.
I'm trying to see if there are some conflict issues with the nforce drivers but am still looking.
My setup is this.
AMD 64 3000+
K8n Neo Platinum nforce 3 250 Bios 1.4
Western Digital 120 gb hd
PQI 3200 1 gig memory
PNY 6800 GT
Audigy 2
Antec Trupower 420
Any help would be great as I'm totally stuck. Thanks.
Also to note I can play DVDs and use recode fine off the DVD rom drive but just not off the DVD writer (411s).

Quote
Originally posted by BluddSimple
I have a Lite on LDW 411s dvd writer that is on the same ide channel as a lite on dvd player (labled as JLMS SJ-HD1665 in the device manager.
You might have better luck making the reader the slave on the channel your HD is on. I had both a burner/writer on the same channel and while it worked, the performance was very poor.
Man, I need to get around to posting my specs someday, but I have the same MB and BIOS as you. I'm also using the nForce unified drivers including IDE.

K8N Neo Platinum and Maxtor HD problem

I have a K8N Neo Platinum MB with the v1.3 Bios installed.
I have 2 physical HDs:
IDE Primary Master: 120G Western Digital WD1200JB (7200RPM)
IDE Primary Slave: 120G Maxtor 6Y120L0 (7200RPM)
The MB sees both drives in the BIOS, however, in Windows XP, I only see the master drive. The slave drive is not recognized within windows. I tried finding the slave drive with the MS Computer Management application and PartitionMagic as well - neither can see the slave drive.
There is something strange about the BIOS screen.
You can see that the primary master is highlighted (in red). The primary slave drive is visibly but it's not showing properly. You can see that the name of the slave drive is all the way to the left and the "]" character is all the way on right panel, next to "Press [Enter]". The name of the slave drive is wrong. The BIOS is showing something garbled. It looks something like "8t/r 6!128". It's tottaly confused :(
I can even select the primary slave drive:
That's not right!
Pressing enter on the slave drive shows the slave drive (Maxtor 120G) properies:
However, Windows XP will not recognize the slave drive.
I ain't sure what wrong but it appears to be a BIOS problem - why would the BIOS display be so messed up like that ??
I'm not sure what to do. :(

Yea, I'm really mad because not only will this board not recognize my slave driver properly, it may have also killed my X800 Pro video card
I moved my working X800 Pro video card from my old MB to my new one and when I turned it on, the X800 Pro was dead.
I then reinstalled my old MB, hoping it was merely a faulty MB that was the problem, however, my X800 Pro is quite dead now
I'm not sure if it was me who damaged the X800 Pro or it was the MSI K8N motherboard - either way it's dead
My experence so far with my new MSI MB has been horrible !!

K8n neo platinum and hard drive problem...

greetings...
well, I have K8n neo platinum mobo with SATA1 controller, and I bought WD 250 GB sata2. I did set up jumper to limit transfer to SATA1 mode on my new drive (although I tried it without jumper, it is the same). Hard disk is working but, I have varying trasfer rate when I copy files from WD250 on other drives, and when copying on that drive. Transfer is going fine, and then it goes very very slow, then again fast, then again slow...And, sometimes, when I am copying large amount of data on that drive, my computer freezes. When I test sustained speed, it is different almost every time (goes from 14 to 65)...
I searched thru internet - with no sucess. I have very good power for my PC. I changed sata cables, and power cables. I updated all drivers. I tried installing XP IDE drivers for that new SATA2 hard disk. I tried almost everything, and with no sucess. WD250 is working fine for, let's say, a couple of hours, and then it again goes slow with varying transfer rate when copying. I also have a very good cooling system, so it's not because of overheating. I contacted WD, they told me to run their diagnostic tool, and the disk was healthy. They said that drive is ok then, and that it is probably my mobo that is causing problems.
anyone have a clue what is going on?
thanx in advance

damn...
can't believe no one ever had similar problem...

K8N Neo Platinum + Sonata Front Panel Audio Problem

Hello,
The front panel audio speaker output is reversed when using headphones on my K8N Neo Platinum and Antec Sonata case. If I swap the left and right front panel audio output signal connectors, the headphone speakers are fine, but then my normal front speakers are reversed. All other connectors seem to be plugged in correctly. I've tried using nvswap, but doesn't seem to work on nForce3. Currently using Realtek driver version 5.10.0.5620 (had the same problem with the drivers included on mb cd) on WinXP Pro SP1 and 5.1 speaker setup (would like to use FPA for mic/headphones while gaming).
Let me know if you need any additional info.
Thanks.

I am having the same problem as well. Was able to correct front output jack by switching the connections. But rear audio is still backwards. I havent tried any sort of 5.1 or 7.1 channel audio setups

K8N Neo Platinum - Reboot problems

This is very strange.......
Just bare with me as I try to explain.
I just orderd a new system to build from scratch and all seemed to go ok.
I have:
Motherboard: K8N Neo Platinum
CPU: AMD Athlon 64 - 2800+
VIDEO: ATI Radeon 9600XT - 128 MB
RAM: 1GB DDR PC2700 CL2.5 - SAMSUNG - 1 Stick
SOUND: I also have an old PCI sound card in there.
HD: none connected currently
CASE: XG Viper Gaming Case
On my first boot everything seemed to go ok. I saw the post screen. The CPU, the Memory were all recognized the only thing is I don't have a HD in it right now so there was no OS to boot. I went into BIOS and double checked the settings. I noticed the RT clock was off slightly so I changed it. Looked around and made sure the AGP port was selected as my primary video adapter. Besides that I didn't change any other settings.
When I saved the BIOS settings and the computer did an automatic reboot I got nothing except a repeating "BEEP" and a black screen.
I waited a few seconds (around 20) then turned the computer on and it started up fine again. This time I didn't go into BIOS just let it boot up to the point where it said INVALID system disk. I did a reboot with the same problem - a repeating "BEEP" and a black screen.
A warm reboot doesn't do anything - It only comes back up with a black screen and the repeating beeps. Also If I power down and up too quick I also get no other effect than the black screen and repeating beeps.
The only way to get the post screen is to let it sit around 20 seconds and boot up.
Even If I let it sit over night, boot it up, see the post, and reboot 2 seconds after I get the post screen, the black screen and the beeping occurs (so I am not too sure its a CPU heat issue).
also on a side note the DBracket has some strange lights on it. - IF I am looking at the Dbracket from the right orientation - I think it is giving a "Initalizing Keyboard Controller" error when I get the black screen. It is either that or the Video Interface error. - 3 RED LIGHTS and 1 GREEN LIGHT.
Any sugestions or help would be GREATLY APPRECIATED !!!
Thank you !!!!!!

OK - I pulled out the 9600XT and put in a 9000 saphire radeon card with the same effects.....
when I pull out the Video card and the memory I get the same black screen and error code of course...
second - I put the memory in and left the video card out only and got a signle long beep.. then no additional beeps after that but of course no video...
third - I put in the video card (the 9600 XT) and left the memory out and got the identical black screen and repeating long beeps.
last - I put the memory back in.. booted up fine... then tried to reboot and I was back to the black screen with multiple long beeps..
one interesting thing that I learned from this was - when there was no memory in I got the same "beeps" as I do when I try to reboot with the memory in... could it be something to do with the memory?.... or is it still leaning toward a PSU problem..
(Unfortunatly I don't have access to another stick of memory right now,... nor a sufficient PSU for the system...)
HELP !!!!

Problem k8n neo platinum

Similar Messages

Maybe you are looking for