Problem logging in after software update today

My MacbookPro wouldn't restart automatically when I updated Leopard via software update this morning. In fact, it appeared to freeze immediately after I agreed to restart for the update (and after I had closed all open software), so I restarted it by hitting the power button. After the restart, some preference file was deleted because it kept putting me in the initial login loop for .Mac and kept asking for my info again and again after every restart. I then plugged in my Time Machine hard drive to restore from my backup just prior to the update attempt. That wouldn't move forward because my 92GB hard drive didn't have enough room to reinstall my 75GB profile.
I started looking at what I could remove, and decided to be doubly-sure of retaining my info so I hooked my laptop up to my iMac running Leopard and copied over everything via target disk mode and firewire. That took most of the morning, after which I removed the entire contents of my laptop and told it to restore. It didn't work. Hours later (my external is a USB drive that is more than adequate unless you are moving 75GB), I got no improvement of results - no change. Thinking myself up to the task, I reconnected via target disk mode and swiped clean my whole laptop hard drive, then opened time machine on the iMac and restored the entire final backup. Now I get no system file with blinking lights at login. My Leopard install disk is at the office, and unaccessible until tomorrow. Is there any way to fix this?

Hi...
If you have iCloud enabled and you are syncing Safari Bookmarks that also syncs the Reading List with other devices.
Quit Safari.
Open System Preferences > iCloud
Deselect the box next to Bookmarks then reselect it.
Relaunch Safari. Try opening the Reading List.
If you do not use iCloud. try deleting the cache associated with Safari.
Go to ~/Library/Caches/com.apple.Safari/Cache.db. Move the Cache.db file to the Trash.
For Lion v10.7x: To find the Home folder in OS X Lion, open the Finder, hold the Option key, and choose Go > Library
Move the Cache.db file to the Trash.
Quit then relaunch Safari. Try the Reading List
edited by: cs

Similar Messages

Unable to Log In After Software Update

Hello:
After running Software Update, I am unable to log in.
I found the following support article:
Mac OS X 10.5: Unable to log in after an upgrade install
Article: TS1543
http://support.apple.com/kb/TS1543?viewlocale=en_US
However, upon step 8 of the instructions, the following error appears:
delete Invalid Path
<dscl_cmd> DS Error: -14009 (eUnknownNodeName)
This is actually after an update (not an "upgrade"), so I'm not even sure these are the appropriate steps.
This is the second time that I have been unable to log in after an update. The first time, I attempted to reset the password with the installation DVD; however, this resulted in "No LDAP Master" errors and I installed Mac OS X 10.5 Leopard Server on a second internal drive and configured everything again. After setting everything up on the second install, I was going to reformat the first boot drive. Unfortunately, I'm just back to where I started after running the updates. I'm not sure if having two volumes with Mac OS X Server installed makes a difference in the instructions in the article mentioned above or not.
Another question: Is resetting the password with the installer DVD the same as using the Single User approach ("launchctl load /System/Library/LaunchDaemons/com.apple.DirectoryServices.plist", "ls /Users", then "dscl . -delete /Users/username AuthenticationAuthority")?
If so, I'll just do that; however, I am hoping that the Single User approach might somehow avoid "No LDAP Master" errors again.
Any suggestions are greatly appreciated.
-Warren

baltwo:
Thanks! I think a week would have gone by before I realized this on my own.
-Warren

Cannot log on after software update

Hi All -
Not sure what happened, but I installed the latest software update from Apple (iTunes 7.7 and a security patch). When I rebooted, I got the log-in screen, which never happens. I tried to log into the main user account, the log-in box just shook. I tried the other user account (which is never used) and it didn't work either. The passwords are correct. I found some help for the same issue in Leopard, and followed it, but that didn't work, as I was getting "Segmentation Faults" messages.
This is the first real issue with my computer in the 5 years. But I am definitely frustrated. Any help would be greatly appreciated. Thanks in advance.
- Greg

Hi Greg, and a warm welcome to the forums!
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
The usual reason why updates fail or mess things up, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates.
May even need to do an Archive and Install if you have room on the HD...
http://docs.info.apple.com/article.html?artnum=107120
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.

Problem with Java after Software Update to 10.5.7

Hi,
I am facing problem with Java after having run Software upgrades.
Here is the whole story. I recently moved to iMac 10.5.6 from PowerPc 10.4. On this new machine I was having problem running a 3rd party application, which requires JVM. As this application worked well on Tiger, I decided to upgrade JVM on my iMAC using Software Upgrade(was I insane!!). As I like my systems to be updated (as with linux on my personal machine) I clicked "install all". As a result I have the following upgrades run on my machine:
2009-05-20 13:12:01 +0200: Installed "Mac OS X Update Combined" (10.5.7)
2009-05-20 13:12:10 +0200: Installed "Remote Desktop Client Update" (3.2.2)
2009-05-20 13:12:26 +0200: Installed "Java For Mac OS X 10.5 Update 2" (1.0)
2009-05-20 13:58:36 +0200: Installed "Java for Mac OS X 10.5 Update 3" (1.0)
2009-05-20 13:58:44 +0200: Installed "AirPort Utility Software Update 2009-001" (5.4.1)
2009-05-20 13:59:07 +0200: Installed "QuickTime" (7.6)
2009-05-20 13:59:22 +0200: Installed "iPhoto Update" (7.1.5)
2009-05-20 13:59:28 +0200: Installed "iLife Support" (9.0.2)
2009-05-20 13:59:38 +0200: Installed "iDVD Update" (7.0.3)
2009-05-20 13:59:58 +0200: Installed "iTunes" (8.1.1)
But now, simply running $java on the prompt hangs, i.e. it takes no action.
$ which java
/usr/bin/java
$ ls -ltr /usr/bin/java
May 20 15:09 /usr/bin/java -> /System/Library/Frameworks/JavaVM.framework/Versions/Current/Commands/java
$java (no response)
Here is the output of $ top
PID COMMAND %CPU TIME #TH #PRTS #MREGS RPRVT RSHRD RSIZE VSIZE
703 java 98.8% 0:38.54 3 110 72 480K 184K 1964K 40M
Any clues?
Details of JavaVM on my machine
$ pwd
/System/Library/Frameworks/JavaVM.framework/Versions
$ ls -ltr
total 56
drwxr-xr-x 3 root wheel 102 Dec 2 2007 1.3.1
lrwxr-xr-x 1 root wheel 3 Aug 31 2008 1.4.1 -> 1.4
drwxr-xr-x 8 root wheel 272 Aug 31 2008 1.4.2
drwxr-xr-x 8 root wheel 272 Aug 31 2008 1.5.0
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.3 -> 1.3.1
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.4 -> 1.4.2
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.5 -> 1.5.0
drwxr-xr-x 8 root wheel 272 May 20 13:12 1.6.0
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.6 -> 1.6.0
drwxr-xr-x 8 root wheel 272 May 20 13:12 A
lrwxr-xr-x 1 root wheel 1 May 20 14:57 Current -> A
lrwxr-xr-x 1 root wheel 3 May 20 14:59 CurrentJDK -> 1.5
Any suggestions? Is there a cleaner approach to uninstall Java on Mac then a simpl "move to thrash"!
cheers

Hi,
I am facing problem with Java after having run Software upgrades.
Here is the whole story. I recently moved to iMac 10.5.6 from PowerPc 10.4. On this new machine I was having problem running a 3rd party application, which requires JVM. As this application worked well on Tiger, I decided to upgrade JVM on my iMAC using Software Upgrade(was I insane!!). As I like my systems to be updated (as with linux on my personal machine) I clicked "install all". As a result I have the following upgrades run on my machine:
2009-05-20 13:12:01 +0200: Installed "Mac OS X Update Combined" (10.5.7)
2009-05-20 13:12:10 +0200: Installed "Remote Desktop Client Update" (3.2.2)
2009-05-20 13:12:26 +0200: Installed "Java For Mac OS X 10.5 Update 2" (1.0)
2009-05-20 13:58:36 +0200: Installed "Java for Mac OS X 10.5 Update 3" (1.0)
2009-05-20 13:58:44 +0200: Installed "AirPort Utility Software Update 2009-001" (5.4.1)
2009-05-20 13:59:07 +0200: Installed "QuickTime" (7.6)
2009-05-20 13:59:22 +0200: Installed "iPhoto Update" (7.1.5)
2009-05-20 13:59:28 +0200: Installed "iLife Support" (9.0.2)
2009-05-20 13:59:38 +0200: Installed "iDVD Update" (7.0.3)
2009-05-20 13:59:58 +0200: Installed "iTunes" (8.1.1)
But now, simply running $java on the prompt hangs, i.e. it takes no action.
$ which java
/usr/bin/java
$ ls -ltr /usr/bin/java
May 20 15:09 /usr/bin/java -> /System/Library/Frameworks/JavaVM.framework/Versions/Current/Commands/java
$java (no response)
Here is the output of $ top
PID COMMAND %CPU TIME #TH #PRTS #MREGS RPRVT RSHRD RSIZE VSIZE
703 java 98.8% 0:38.54 3 110 72 480K 184K 1964K 40M
Any clues?
Details of JavaVM on my machine
$ pwd
/System/Library/Frameworks/JavaVM.framework/Versions
$ ls -ltr
total 56
drwxr-xr-x 3 root wheel 102 Dec 2 2007 1.3.1
lrwxr-xr-x 1 root wheel 3 Aug 31 2008 1.4.1 -> 1.4
drwxr-xr-x 8 root wheel 272 Aug 31 2008 1.4.2
drwxr-xr-x 8 root wheel 272 Aug 31 2008 1.5.0
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.3 -> 1.3.1
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.4 -> 1.4.2
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.5 -> 1.5.0
drwxr-xr-x 8 root wheel 272 May 20 13:12 1.6.0
lrwxr-xr-x 1 root wheel 5 May 20 13:12 1.6 -> 1.6.0
drwxr-xr-x 8 root wheel 272 May 20 13:12 A
lrwxr-xr-x 1 root wheel 1 May 20 14:57 Current -> A
lrwxr-xr-x 1 root wheel 3 May 20 14:59 CurrentJDK -> 1.5
Any suggestions? Is there a cleaner approach to uninstall Java on Mac then a simpl "move to thrash"!
cheers

After software update today, the Reading List on my Safari cannot be opened!

Hello guys,
After the software update I had earlier on in the day, I can't seem to open up the Reading List on Safari. Do you guys have the same problem too?
Regards,
Bo Wei

Hi...
If you have iCloud enabled and you are syncing Safari Bookmarks that also syncs the Reading List with other devices.
Quit Safari.
Open System Preferences > iCloud
Deselect the box next to Bookmarks then reselect it.
Relaunch Safari. Try opening the Reading List.
If you do not use iCloud. try deleting the cache associated with Safari.
Go to ~/Library/Caches/com.apple.Safari/Cache.db. Move the Cache.db file to the Trash.
For Lion v10.7x: To find the Home folder in OS X Lion, open the Finder, hold the Option key, and choose Go > Library
Move the Cache.db file to the Trash.
Quit then relaunch Safari. Try the Reading List
edited by: cs

Problems with Macbook after Software Update

I haven't updated my Macbook in a long time, so I decided it was time I probably did. Software Update had updates for iTunes, Quicktime, and a 2009-Security Update. Everything seemed to be going okay. After the downloading and installing finished, it said the Security Update couldn't be installed and moved it to the trash. Then it prompted me to restart my computer because the other two installed okay.
After restart, when my computer started back up, my Macbook is messed up. The doc is missing. I open a finder window, and it shows the main folders, but all the things on the right (where it shows the drive, applications, and such) is missing. I tried to back up my files, but it can't even read there is a blank disc inserted (keeps asking me to insert a blank disc). And it wont let me shut down my computer, or restart it. I click restart, and it seems like it accepts it, but it just doesn't do anything. The dashboard wont show up when you hit F12. This mac is all messed up.
I don't know what happened here, all I installed was iTunes and Quicktime from the Software Update (security update didn't install), and all this happened. Any idea what happened and how I can fix this?
I'm using Mac OSX Tiger 10.4.11.

Welcome to Apple Discussions.
There's a variety of things you could try, but first as to why it is doing this. Probably your drive was slightly corrupted. If it was minor you might not have noticed it, but when the updates tried to install, the whole thing compounded and led to a whole bunch of things missing.
First, try to repair your drive. Boot from the System installer disc that came with your computer or is the one for the version you currently have on there, select language if applicable, choose utilities, run Disk Utility and verify (and repair if necessary) the drive. You can verify a drive from DU on your main drive while booted but I have found this can result in incorrect reporting of errors. To repair your drive you have to run it from a drive other than the boot drive anyway.
Next, boot from your drive in [Safe Mode|http://docs.info.apple.com/article.html?artnum=107393] and repair permissions. You can repair permissions while booted from the installer disc but this uses the permissions configuration on the installer disc which may be out of date if you have run any updates on your computer. Booting your computer to Safe Mode restricts the number of things running on your computer while permissions are being run and does a bit of spring cleaning at the same time.
Reading
[Resolve startup issues and perform disk maintenance with Disk Utility and fsck|http://docs.info.apple.com/article.html?artnum=106214]
[Using Disk Utility in Mac OS X 10.4.3 or later|http://docs.info.apple.com/article.html?artnum=302672]
[Disk Utility's Repair Disk Permissions|http://docs.info.apple.com/article.html?artnum=25751]
+Summary of above from BDaqua+ (couldn't have said it better):
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer (Edit: Do not use this disc if it is not the same general version as what you have currently on your computer, e.g. use a Tiger disc for a Tiger drive, not a Panther disc), then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
Then Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes."
Report back after you have done this. It may be that you have to use a more powerful utility such as Diskwarrior.
Once the drive is repaired you can try re-applying the two updates, though often it takes a full archive and install, plus re-application of all updates, to get everything working again.
[Mac OS X: About the Archive and Install feature|http://support.apple.com/kb/HT1710]
[Apple document about A&I in Tiger (10.4)|http://support.apple.com/kb/HT1545]
[X-Lab Archive and install|http://www.thexlab.com/faqs/archiveinstall.html]
[Kappy's A&I instructions|http://discussions.apple.com/thread.jspa?threadID=1823034]
*In most cases _make sure_ you select "Preserve Users & Settings"*
Finally, on updating:
Updating
Certain steps appear to minimize the risk of an update producing problems.
Number one is to make sure you have a bootable clone backup of your computer in case you do need to back out of it again. This is the only guaranteed way of not having to worry about the results of an update.
Some like to boot from their installer discs or an external backup and verify (and if necessary repair) their internal drives as well as drive permissions. This is done with Disk Utility. You can verify a drive while booted from the same drive but sometimes this produces spurious errors. Repairing a drive (if necessary) has to be done while booted from another disk.
[Resolve startup issues and perform disk maintenance with Disk Utility and fsck|http://docs.info.apple.com/article.html?artnum=106214]
[Using Disk Utility in Mac OS X 10.4.3 or later|http://docs.info.apple.com/article.html?artnum=302672]
[Disk Utility's Repair Disk Permissions|http://docs.info.apple.com/article.html?artnum=25751]
You can also go to the step of booting into safe mode to do the install.
[Mac OS X: Starting up in Safe Mode|http://docs.info.apple.com/article.html?artnum=107393]
[What is Safe Boot, Safe Mode? (Mac OS X)|http://docs.info.apple.com/article.html?artnum=107392]
[Safe Boot takes longer than normal startup|http://docs.info.apple.com/article.html?artnum=107394]
I like to download the update onto my computer and install it from there rather than let Software Update do it. I know a few people who had problems with doing the update via software updater found a manual install to work.
Repair permissions again afterward.
It helps to only install one update at a time and to run the computer for a while to make sure it is behaving well.
The more cautious even like to unplug third party peripherals (see [comment by BDaqua|http://discussions.apple.com/message.jspa?messageID=9040746#9040746]).
Almost all of the above steps (except backup) have been questioned (e.g., [Permissons repair|http://www.macworld.com/article/52220-3/2006/08/repairpermissions.html] as to necessity. Probably many people have done successful updates without doing them. I say they can't hurt, they can very likely do good (especially if your computer isn't regularly maintained), so why not do them to be safe?
[BDaqua's comments on updating problems|http://discussions.apple.com/message.jspa?messageID=8948595#8948595]
[Baby Boomer's comments on updating problems|http://discussions.apple.com/message.jspa?messageID=9025760#9025760]
[Klaus1's post on updating and removing updates|http://discussions.apple.com/message.jspa?messageID=10257902] and [another one|http://discussions.apple.com/message.jspa?messageID=10402175]

HELP! Problems with MacBook after software updates install.

Hi Guys,
I have a friend of mine that has a MacBook. After a while without doing the software updates she connected her MacBook on the internet and there was a lot of software updates to do, so she went on and install everything. She describes me that the problem was with Tiger 10.4.11, it pop up a "Warning Sign - Error" and freezes she says.
She re-start the computer and It get stuck on the gray window with the Apple with the lil circle spinning endless.
Is there any tip or something that I can help her?...
[Sorry about my english... lol)

Hello coreanomac!
The following Apple Support article is good for working through the problem. Based on your explanation of what happened, follow the advice of the "Try a different software update source" and "Installation fails during 'optimization'" paragraphs of the "Troubleshooting an unsuccessful installation" section:
Mac OS X: Troubleshooting installation and software updates
Also reading the "Before Installing" section may be useful, as well.

Problems with startup after software update

I have just done a software update on my system, and now going back to my computer 2 hours later and turning it on, all I get is the grey screen with the apple and dial spinning...........
Also the fans in the tower are going nuts.
Is this normal for updates since leopard, seeing as I have never had this happen to me before

No, that's not normal. It could be hardware. Shutdown.
Run Apple Hardware Test:
1. Disconnect all external devices from your iMac except the keyboard and mouse.
If you have an Ethernet cable connected, disconnect it.
2. Insert the Mac OS X Install Disc 1 that came with your iMac.
3. Restart your iMac and hold down the D key as your iMac starts up.
4. When the Apple Hardware Test chooser screen appears, select the language
appropriate for your location.
5. Press the Return key or click the right arrow button.
6. When the Apple Hardware Test main screen appears (after about 45 seconds), follow
the onscreen instructions.
7. Apple Hardware Test displays an error code if it detects a problem. Make a note of the
error code before pursuing support options.
Let us know.
-mj

Problems w/ AirPort after Software Update

I ran Software Update last night on my Powerbook and ever since I haven't been able to access the Internet wirelessly. AirPort is on, and I've had to submit my password, but I have no connectivity.
I believe this has happened to me before and restarting has helped. But it didn't this time.

I too have had the same problem with my iBook/Airport Extreme... still no solution yet I'm afraid though

Trouble logging in after software update.

This occured last night as i was watching Apple's new keynote address. Once i logged into my macbook, the usual software update popped up (new itunes, imovie, etc..) (All for leopard by the way). I also found out of the new software updates for the ipod touch. So i then went ahead and started the update for both my ipod and my macbook. As usual, it requested that i restart my macbook. However, just as i started to do the restart, a little window popped up notifying me of some Cache update or something. I went ahead and just did the restart. Now, i cant log into my macbook. The usual log in screen comes up, and i am able to put in my log in password, but once i do so it takes me to a blue screen for about 3-4 seconds and then takes me back to the original log in screen. I tried to restart the computer with the shift button for safe mode and it did the same thing. I also tried the option+apple commandrp command and it keeps giving me the same thing. Any suggestions?
Message was edited by: Beau is cool
Message was edited by: Beau is cool
Message was edited by: Beau is cool

Hi,
See here for Safe Mode:
http://support.apple.com/kb/HT1564?viewlocale=en_US
AS to the Combo Resolving your Issue... It may or may not...
But give Safe Boot a Try First...

I'm having all kinds of problems since loading Lion and I really wish I hadn't bought it yet. Even after the software update today, 1. my modem still won't work, 2. Photoshop Elements produces muddy photo prints, etc. Anybody at Apple listening?

I'm having all kinds of problems since loading Lion and I really wish I hadn't bought it yet. Even after the software update today, 1. my modem still won't work, 2. Photoshop Elements produces muddy photo prints, 3. View preferences in windows don't hold, etc. Anybody at Apple listening? Anybody else out there having these kinds of problems?

10.7 was horrible unstable so I waited until 10.7.1 and tried it again. Well I have to say that it is still a defective OS. I am reverting to Snow as we speak from my carbon clone copy.. This is really the worst OSX I have ever used. It gives me random Kernel panics for no reasons, unstable airport and hundreds of small issues that are just not necessary. For instance I can't use QuickTime in Lion to trim a videoclip ( the UI goes mad and the trimslider becomes inoperable and hangs the Player window ) while in Snow it is no problem. Itunes gives me crackling sound when the equalizer is turned on, Graphical glitches in Photoshop, games crashing, Preview.app not working with some pdfs, so I need Adobes reader which I never used before.. It is definately not ripe for mass usage. Might 10.7.2 or 10.7.3 fix it, but not yet.
* and just for the records : the hardware is absoltely ok. Because in Snow it works as it should. ( So many Lion fanbois are talking : "your Ram is defect", defintely NOT. - Lion is defect! ).
Shame on you Apple.
Message was edited by: Sjazbec

Problem restarting after software update

Computer is fine, drive 40% full, no speed problems...
But it just won't restart after software update runs, nor will it restart or shut down from finder.
Problem solving so far: Safe boot, reset pram, ran disk utility, ran disk repair using install disk, ran fsck -y, ran disk warrior.
Is annoying. ANy ideas anyone? If not, what is the procedure for updating using sudate and terminal, as when I use software update, a force shut down will not install.
ANy ideas folks?

Some general advice on updating:
It is worth noting that it is an extreme rarity for updates to cause upsets to your system, as they have all been extensively beta-tested, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first to an external hard disk. Ideally you should always have a bootable clone of your system that enables you to revert to the previous pre-update state.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site.
The Combo updater of Leopard 10.5.8 can be found here:
http://support.apple.com/downloads/MacOS_X_10_5_8_ComboUpdate
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Full details about the 10.5.8 update here: http://support.apple.com/kb/HT3606
More information on using Software Updater here:
http://support.apple.com/kb/TA24901?viewlocale=en_US
Using the Combo updater ensures that all system files changed since the original 10.5.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.5.7 to 10.5.8. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications and turn off energy saving and screensaver.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them compliant with the latest version of your operating system. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 4.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
If you are updating Safari (or just have):
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed an OS update and Safari is crashing, the very first thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party add-on.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692
To reiterate, Input Managers reach right into an application and alter its code. This puts the behavior of the affected application outside the control and responsibility of its developers: a recipe for problems. That's not to say that issues absolutely will ensue as a result of Input Managers, but you, as a user, must decide. If the functionality of a specific Input Manager or set thereof is really important to you, you may well choose to assume the associated risk.
Again, the advice is to remove all Input Managers from the following directories:
• /Library/InputManagers
• ~/Library/InputManagers
especially prior to system updates (they can always be added back one-by-one later).

New iPad with retina display with 30 pin connector mirroring to TV with dvi adapter problems after software update

Hi. Good day to everyone my New iPad with retina display 30 pin connector will not mirror to TV even with divi adapter after software update. Adapter works fine. Or is it a software glitch with IOS 7.04? I've tried resetting and reconnecting nothing seems to work.

That's one of the weird things.. it recognizes it maybe 10% of the time. And usually, only after I do the two-button reset. Problem is.. since it won't charge above 2%, anytime I try to do a restore or anything like that using iTunes, my device shuts off and I lose whatever progress I'd made.
So, an update... after reading through a bunch of similar complaints (there are literally 1000's of them so there's NO WAY this isn't somehow ios7 related, thanks a lot APPLE ) I decided to try a restore in recovery mode. After 3 hours and several disconnections... I ended up having to just set it up as a new iPad, as the restore did nothing. Weirdly though... as I was doing the restore in recovery mode.. I noticed I'd gotten up to a 10% charge.. higher than it's been since September, so after setting it up as a new device, I turned it off and plugged it in using the wall charger. 2 hours later and I was up to 38%. Still not great, as my iPad, before ios7 could've fully charged twice in the amount of time it took for me to now get 28% more of a charge. And that's with a fully cleaned out device.. so that really ***** and I'm now more confused than ever.
But I'm gonna leave it overnight charging and see what I come up with tomorrow. Sadly, when I paid $600 for it in February, I never expected to have to play "wait and see" with it...

Thin white line acroos the top of my screen after software update. Can NPRAM reset help to solve this or is it a permanent pixel problem?

Sudden thin white line acroos the top of my screen after software update. Can NPRAM reset help to solve or is it permanent pixel problem?

Try PRAM reset.
Reset PRAM: http://support.apple.com/kb/PH14222
Best.

Problem in curve 9320 after software update

Hi, i had updated my curve 9320 with new software as recommended by blackberry desktop software. After the update i am facing many issues after software update:
1. whenever I am trying to make a call or opening any message my phone power suddenly goes OFF and not starting till I pullback the battery and re-inserted.
2. Some time automatically its battery got heated up and there is discharge of battery, but when i pull back and re-inserted battery it becomes normal.
3. Email setup is not working, I am not able to add any email account. whenever I am clicking on email setup there is no reaction.
please suggest what to do. I tried to go back to download old software but I am not able to get it anywhere online.
regards
iftekhar

Hey iftekhar,
Welcome to the BlackBerry® Support Community Forums.
I would suggest backing up doing a clean reload of the BlackBerry® device software as shown here: http://btsc.webapps.blackberry.com/btsc/KB11320. Please test before restoring any data to the device.
If this resolves the issue do a selective restore of essential data (Address Book, Calendar, Task, Memos, BBM contacts etc.)
How to use BlackBerry® Desktop Software to restore data to a BlackBerry® smartphone from a backup file
http://btsc.webapps.blackberry.com/btsc/KB10339.
If the issue still persists after the reload, further investigation might be required. To help further diagnose the cause, contact your wireless service provider or BlackBerry® Technical Support Services for further review and support.
Thank you.
-HB
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Problem logging in after software update today

Similar Messages

Maybe you are looking for