Problem Monitor Port stops working

I set up a customer and put in a SPAN port on the switch and hooked it in as it should so that we can use the NTOP program.  After 10 - 15 min it stops getting data.  We reboot the onplus device and it starts working again for 10 min and again will stop.
Could this be a bad box or what should I do?

All,
After a call with Michael, we observed that he can still reach the GUI for NTOP and the main summary page shows the stats there updating. The problem appears when he clicks on the 'graph' icon just at the bottom of the main summary page's 'Traffic Report for 'eth1'' section. I'm able to reproduce the dead graph results on my system, but it appears that NTOP isn't stalled, but the graphs on this page seem not to update. As this is a third party tool, we're taking a look at the latest version and then also checking to see if this is some sort of an auto-scaling issue.
The key point is that we'd love to find out if others are referring to this single graph page being stalled or is the NTOP main page no longer updating too. If you can still reach the NTOP main page, please share with us what part isn't updating.
Thanks,
Robert

Similar Messages

  • USB ports stopped working in my Macbook Pro

    USB ports stopped working in my Macbook Pro

    I do not know anything about audio consoles nor do I have an iPhone.
    My iPod also does not show on the desktop but it is recognized in iTunes,  Check if that is the case for your MBP. 
    Do you have the appropriate boxes checked in Finder Preferences?
    See if this support article is of any assistance:
    http://support.apple.com/kb/TS1410
    If you have an external HDD, connect it to your MBP and see if it is recognized.  If it does not show on the desktop, check Disk Utility.
    Have you tried all USB ports?  It could be that the problem lies in your MBP.
    Ciao.

  • MAC PRO Internal USB ports stopped working

    Hello, I have a mac pro 8 core with an USB internal ports problem, the 2 in front are not working anymore, and from the 3 in the back only the middle one is working.
    I tried to pull all the power out for a whole night, resetting the pram and nvram but nothing helps.
    When for example I put in a keyboard in one of the ports that is not working and when I power up the machine and I press the ALT key I get the choice of startup preferences, once I select one, and the system boots up the ports stops working, so before the OS loads the usb ports are working !!!
    What to do ??

    This is a hardware failure. While USB ports on the whole are just not designed very well, leading to their failures being pretty common, your issue sounds a bit more like the USB controller chip is failing.
    In any case, the answer is to take it to a repair shop. If they're smart about it, they'll replace the logic board and see if that also fixes the front ports. If not, they'll replace the front I/O panel as well.

  • MDB and Database - Listener port stops working

    Hi,
    I have created an MDB which does the following when a message is received from the queue.
    1. Store message in database
    2. do some processing
    At step 1, if there is any issue with the database connection (e.g. database is not available etc), I rollback transaction. My idea is to leave the message on queue for now and retry it again after some time unless the database is back again. "Maximum retries" of the listener port is set to N but since there is no retry interval available, all N retries are done in a flash and my listener port stops working. I cannot use backout mechanism as I have to wait for the database to be back again. What are my options?

    usmanchaudhry wrote:
    Hi,
    I have created an MDB which does the following when a message is received from the queue.
    1. Store message in database
    2. do some processing
    At step 1, if there is any issue with the database connection (e.g. database is not available etc), I rollback transaction. My idea is to leave the message on queue for now and retry it again after some time unless the database is back again. "Maximum retries" of the listener port is set to N but since there is no retry interval available, all N retries are done in a flash and my listener port stops working. I cannot use backout mechanism as I have to wait for the database to be back again. What are my options?i believe you need an XA driver and a transaction manager, for starters.
    a simple JDBC rollback won't do it.
    which app server are you using?
    which jms provider?
    %

  • HP Pavilion external monitor has stopped working with my Macbook Pro (Mid 2012) with OSX 10.8.3

    HP Pavilion external monitor has stopped working with my Macbook Pro (Mid 2012) with OSX 10.8.3.  When I purchased the monitor a few weeks ago it worked perfectly when computer was in clamshell mode or with lid open. Now external display has stopped working.  When I turn on display it scans for signal but does not find it and then immediately goes into sleep mode.  I am using a DVI connection with the adapter for the mini display plug.  REALLY FRUSTRATING. Any help would be extremely appreciated. 

    Hi lancekatigbak,
    If you're having issues with the display out on your MacBook Pro, you may want to take a look at the troubleshooting steps in the following article:
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/ht1573
    Cheers,
    - Brenden

  • HP Pavilion dv6 All 4 USB ports stopped working

    Hello,
    I recently bought a Pavilion dv6-6c11sa laptop. Windows 7 Home Premium 64-bit
    Everything was working fine for about a week, and then yesterday all of the USB ports stopped working. I have 4 USB ports in total, two 2.0 and two 3.0. No matter what peripheral device I plug in, mouse or flash drive etc, they're not recognized by the laptop. The lights don't even light up on the devices, regardless of the port. I've tried uninstalling and reinstalling the drivers in device manager, taking out the battery and rebooting, installing the chipset drivers (AMD), nothing works. No programs had been installed 3 days prior to the occurence, although I had rebooted several times in that time frame. I simply booted up the laptop yesterday, and nothing worked.
    Could anyone offer a solution or suggestion, please?

    Hello,
    I recently bought a Pavilion dv6-6c11sa laptop. Windows 7 Home Premium 64-bit
    Everything was working fine for about a week, and then yesterday all of the USB ports stopped working. I have 4 USB ports in total, two 2.0 and two 3.0. No matter what peripheral device I plug in, mouse or flash drive etc, they're not recognized by the laptop. The lights don't even light up on the devices, regardless of the port. I've tried uninstalling and reinstalling the drivers in device manager, taking out the battery and rebooting, installing the chipset drivers (AMD), nothing works. No programs had been installed 3 days prior to the occurence, although I had rebooted several times in that time frame. I simply booted up the laptop yesterday, and nothing worked.

  • A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port.  WHen we plugged it into the port on the keyboard, the device works. Why?

    A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port.  When we plugged it into the port on the keyboard, the device works. Why?  Obviously the device is operational.  Could the USB port have burned out from having too much power drawn?  If so, is it reparable?

    It can't draw "too much" power, it can only draw as much as the USB port is able to provide and no more. IIRC, the keyboard port has a lower power output than the iMac's port.
    That being said, yea, it's possible that the port has failed and it can be replaced or if another port works you can use that one. Although if it is still under warranty or covered by Apple Care, then I would take it to an Apple Store or service provider to get the port repaired.

  • Ports stopped working.

    I used to use port 8001 for a lot of things. Recently, the port stopped working. I triple checked all my router settings and port 8001 is still forwarded. I tried other ports. I rebooted. I tried shutting off my firewall. Nothing worked. I really need a port working for various things so I need some help. Tell me if you need any additional information and I'll tell you. Does anyone know what I should do??

    Well, I did everything you said and I'm sure I did it right. No luck. I have a feeling that something else is going on here, but I'm not sure what I should do. Anyone have any ideas?

  • 1 of 2 USB ports stopped working after 10.7.2 upgrade

    I have the newest Macbook Pro.  I upgraded to 10.7.2 today and immediately after, 1 of my 2 usb ports stopped working.   Thought it may be the cable, so I switched cables.  Tried plugging in my iPhone, my portable drive and nothing.   Both work on the other port though.   Both ports worked fine before the update. 
    I've rebooted 4x. 
    Suggestions?

        Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the method for:
        "Resetting SMC on portables with a battery you should not remove on your own".
      If this does not help, contact Apple.
      Genius Bar reservation
      http://www.apple.com/retail/geniusbar/
    Best.

  • One usb port stopped working today

    One of my USB ports stopped working today. I think it may be related to Itunes update today. Has anyone else seen this recently? I restarted my computer - but that didn't help. I have a MacBook Pro - running Lion 10.7.5
    Any suggestions? I saw one USB Hub when I went to Apple --> About this Mac, but couldn't tell if both were there.

    http://www.ehow.com/how_7351075_reset-usb-ports-mac-laptops.html

  • Brand new Macbook pro one USB port stopped working

    Brand new Macbook Pro 15 with Retina display. One of the USB ports stopped working after 24hours.

    Serial Port Configuration and Port definition is reset by
    NVRAM  http://support.apple.com/kb/ht1379
    If no good I would return the machine ASAP:
    Genius reservation http://www.apple.com/retail/geniusbar/
    check warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

  • HT1379 MacBook Pro USB port stopped working

    USB port stopped working....
    How can I diagnose my USB port to test for hardware or software problem

    Try Resetting the System Management Controller (SMC)

  • Satellite R830 - USB3.0 port stop working after long time usage

    Hi there,
    This is my new laptop. I got it just one week. However, USB 3.0 port is very weird. It always stop working when i used it for several hours. I try to update the driver, but i still seems not working.
    are there any other solutions?

    >well, it will stop working as well when i use it as data transfer.
    So how long does it take until the USB 3.0 port stops working?
    Does it interrupt the data throughput?
    Did you use the USB 3.0 compatible devices?
    On the Toshiba European driver page you can find the USB 3.0 driver version 2.0.34.1.
    Are u using this version?

  • TS3297 when i try to open itunes store error comes up saying windows experienced a problem and program stopped working

    can some help me everytime I try to open itunes store an error comes up saying windows experienced a problem and program stopped working. Itunes opens this just happens when I go to the store

    Hello Ducati848,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iTunes for Windows Vista or Windows 7: Troubleshooting unexpected quits, freezes, or launch issues
    http://support.apple.com/kb/ts1717
    Best of luck,
    Mario

  • My USB ports stopped working. So did my dvd drive. I have a Pavillion Laptop. Model 1245dx.

    My USB ports stopped working.  Do did my DVD drive.  I did do a Windows update yesterday.  Any ideas out there?  I can't use my mouse or printer.  Help!

    Try a windows system restore, pick a date before the windows updates were installed.

Maybe you are looking for

  • My apple tv is not recognising my apple id and password

    My apple tv is not recognising my apple id and password after this new update. Netflix is also don't let me play any movies. I already reset the equipment, network is ok because some features of of apple tv are working fine such as renting from Itune

  • Settings to stream ripped movie?

    I was pleasantly surprised to see how good one of my DVDs ripped via handbrake looked streaming from my iMac to my Apple TV. What wasn't so pleasant is how it kept halting every 10 minutes or so (buffering?). is the only solution to actually move the

  • Is there a simple way to save and open attachments?

    When I save an attachment in mail, I have to hit save, navigate to the place to save, say OK, then to open it, I have to open a finder window, navigate (again) to the place, and open it. Because we have a very deep directory structure on our corporat

  • How do I get iTunes to match what is actually on PC? (some old songs remain)

    I deleted a bunch of songs on my PC.  They are gone for good, as I emptied my Recycle Bin.   ........But iTunes still keeps these files in the Library.  How do I get iTunes to clean-up the Library? If you click on the deleted songs it can't find the

  • Using Select List value for building report

    I have an interactive report form. I have a "After Header" (LOAD) process that run sql commands that will populate a table with the data that the report needs for a given week. I have a Select List item that is run as a "Before Header" that gets a li