Problem of the poor quality of print as booklet

I hv encounter the problem about the output quality .The file is quite low in resolution while i choose print in booklet,
I use the SAME pdf output setting. The output pdf file from "export (pdf)" it is abvious better than the one from " print as booklet"
How can I fix this problem ?? THX A LOT

Similar Messages

Poor quality Photo printing with the HP Officejet 6600

Is anyone having a problem with the HP Officejet 6600 having very poor quality photo prints?

Hi HereInJersey,
Welcome to the HP Support forums. I understand that printed photos from your Officejet 6600 don't have the quality that you expect.
I have included the "Fixing Ink Streaks, Faded Prints, and Other Common Print Quality Problems" troubleshooting document. It has detailed steps to take to improve the quality of your print jobs.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Why am i getting poor quality photo prints after installing lion using canon pixma 6120?

After installing Lion, I began experiencing poor quality photo prints on my Canon Pixma 6120 printer. Prior to Lion, my picture prints were all high quality. Now, anything black in the picture is faded.

Lion should not cause the blacks to print faded. The printer drivers used by Snow Leopard and Leopard are the same version as that used by Lion.
For starters I suggest you check that you have the latest version installed. This Apple KB article shows the MG6100 series has v10.51.2.0 as the latest version.
I also recommend you do a Nozzle test print. This can be executed from the MG6120 control panel or via the Printer Utilties window (via Print & Scan, select the printer and then open Options & Supplies and then select the Utilties tab).
If the nozzle test print is okay but the blacks still look faded when printing photos (note the printer has two black ink tanks - one for photos and one for text) then try a reset of the printing system. This will remove the MG6120 from the Print & Scan pane but not the supporting drivers. So you will only have to add the printer again.

Im having problem with the dvd quality, I'm using compressor to convert the video fils from apple prores to mpeg2 .It doesn't matter how long my video is even if its just 5 minutes I'm getting cut edges in the video , does anyone have any idea ?

Im having a problem with the dvd quality, I'm using compressor to convert the video fils from apple prores to mpeg2 .It doesn't matter how long my video is even if its just 5 minutes I'm getting cut edges/lines in the video specialy if i have titles it comes up really bad , I took the same video to a friend of mine who have PC and he uses Encore , did the encoding there and it was just fine no problems! BTW I tried using doferent setings in compressor from CBR and VBR I even pushed up the setings to 8 or 9 BR and still no luck !
does anyone have any idea ?
Thanks in advence ...

Let's focus attention on just the Sony. (What model and what resolution are you shooting?)
For now, I'll assume you're shooting 1080i.
Take a representaive clip into a new sequence. Add a title.
In your sequence, make sure field dominance is set to Upper.
Set render settings to Pro Res 422.
After rendering, export QT self contained.
Import into Compressor (I'm now referring to v3.5).
Select the 90 minute Best quality DVD preset.
Open frame controls and turn on (click the gear icon). Set Resize filter to Best.
Submit burn and check quality on TV.
Good luck.

Poor quality photo printing

I am getting very poor quality prints from my new Canon MG6220. I have it set on the advanced photo with glossy paper. Am I missing something?

Are you using Canon brand paper? Unless you have the proper profile for other papers you'll get less than ideal prints. The printer (when working correctly) will spray the correct amount of ink onto the paper, but it's matched to Canon paper. IF you use any other brand it may absorb more ink or less than the printer is set to spray. That has a major effect on the look of the photo.
Also note that most people edit using their monitor set at full brightness, but when they print it's not the same. It's very important to set your monitor's brightness to match what your printer produces.
"A skill is developed through constant practice with a passion to improve, not bought."

Is it possible to improve the poor quality of DVD's?

I started my presentation in Keynote and exported the file as a quicktime movie (high quality). I then moved the quicktime movie into iDVD and when I previewed the project, the quality looked crisp...so far so good. I then proceeded to burn directly to DVD and the quality was, for lack of a better word, crap. I tried creating a disc image and using Toast but unfortunately it's not rearly as sharp as it was within iDVD.
This has been bugging me for about weeks now. I've been reading the discussion boards for a while and haven't found a solution to my problem. Any help would be greatly appreciated.

Hi,
I'm also a very frustrated user experiencing the same problem with iDVD 6. This was not seen when I was using iDVD 5.
I've made a .dv file with imovie 6.0.1, and upon "Sharing" to idvd, I didn't see any drop in quality during preview. Its only when I've the DVD disc image file where iDVD compresses the .dv format to mpeg2 that a significant loss in video quality can be seen.
I've also tried out different methods of encoding the .dv file using other software:
1. Toast 7.0.1 : Same poor quality mpeg2
2. ffmpegX : I tried tweaking different settings, (video bitrate, etc), but only very insignificant improvements were seen. ( Anyone out there with success in finding the right combinations of options, please post reply!)
3. JES Deinterlacer : I don't think the problem lies with interlacing, as I don't see much improvements here either.
Anyway, has anyone checked out this website:
http://www.kenstone.net/fcphomepage/idvd_6stone.html
I've actually contacted the website owner Ken Stone via email, asking him if he has seen this problem. He replied to me that he did not experience quality loss since he did not work with imovie.
I'm pretty baffled here, as I thought the problem clearly lies with the process of dv to mpeg2 encoding, and not the software that was used to create the movie or .dv file?
Anybody out there has a workaround or a definate solution?

Problem with the garbage record getting printed at the beginning

Hello Friends,
I know that this problem is very difficult to solve without looking at my script and its program. But I will try asking anyways.
I have written the following code (Driver program) which uses to tables ZRAMCUSTMAST AND ZRAMCALLMAST.
ZRAMCUSTMAST has customer details like address etc.,
ZRAMCALLMAST has the call details that each
             customer has done.
But when I print the details, it prints everything correctly but for each customer it prints some garbage
values as the first row.
Any feedback will be greatly appreciated. You can mail me the response also (singer_ram AT yahoo DOT com)
CODE in my driver program (SE38) -
*& Report ZRAMPROJSCRIPT                                              *
REPORT zramprojscript                          .
TABLES : zramcustmast, zramjuncmast, zramcallmast.
DATA : itabcustmast LIKE zramcustmast OCCURS 1 WITH HEADER LINE,
       itabjuncmast LIKE zramjuncmast OCCURS 1 WITH HEADER LINE,
       itabcallmast LIKE zramcallmast OCCURS 1 WITH HEADER LINE.
DATA: type_of_call(1),
      CALL_CHARGE type i, CALL_CHARGE_STRING(5), TOTAL_CHARGE type i,
      hour(2), min(2), sec(2).
SELECT * FROM zramcustmast INTO TABLE itabcustmast.
*SELECT * FROM zramjuncmast INTO TABLE itabjuncmast.
CALL FUNCTION 'OPEN_FORM'
EXPORTING
APPLICATION                       = 'TX'
ARCHIVE_INDEX                     =
ARCHIVE_PARAMS                    =
DEVICE                            = 'PRINTER'
dialog                            = 'X'
   form                              = 'ZRAMPROJSCRIPT'
   language                          = sy-langu
OPTIONS                           =
MAIL_SENDER                       =
MAIL_RECIPIENT                    =
MAIL_APPL_OBJECT                  =
RAW_DATA_INTERFACE                = '*'
IMPORTING
LANGUAGE                          =
NEW_ARCHIVE_PARAMS                =
RESULT                            =
EXCEPTIONS
CANCELED                          = 1
DEVICE                            = 2
FORM                              = 3
OPTIONS                           = 4
UNCLOSED                          = 5
MAIL_OPTIONS                      = 6
ARCHIVE_ERROR                     = 7
INVALID_FAX_NUMBER                = 8
MORE_PARAMS_NEEDED_IN_BATCH       = 9
SPOOL_ERROR                       = 10
CODEPAGE                          = 11
OTHERS                            = 12
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
LOOP AT itabcustmast.
CALL FUNCTION 'START_FORM'
   EXPORTING
ARCHIVE_INDEX          =
     form                   = 'ZRAMPROJSCRIPT'
     language               = sy-langu
STARTPAGE              = ' '
PROGRAM                = ' '
MAIL_APPL_OBJECT       =
IMPORTING
LANGUAGE               =
EXCEPTIONS
FORM                   = 1
FORMAT                 = 2
UNENDED                = 3
UNOPENED               = 4
UNUSED                 = 5
SPOOL_ERROR            = 6
CODEPAGE               = 7
OTHERS                 = 8
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CALL FUNCTION 'WRITE_FORM'
   EXPORTING
     element                        = 'MAINPAGE'
     function                       = 'SET'
     type                           = 'BODY'
     window                         = 'MAIN'
IMPORTING
PENDING_LINES                  =
EXCEPTIONS
ELEMENT                        = 1
FUNCTION                       = 2
TYPE                           = 3
UNOPENED                       = 4
UNSTARTED                      = 5
WINDOW                         = 6
BAD_PAGEFORMAT_FOR_PRINT       = 7
SPOOL_ERROR                    = 8
CODEPAGE                       = 9
OTHERS                         = 10
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
clear itabcallmast.
refresh itabcallmast.
SELECT * FROM zramcallmast INTO TABLE itabcallmast WHERE customerid = itabcustmast-customerid.
SORT itabcallmast by calltype.
TOTAL_CHARGE = 0.
LOOP AT itabcallmast.
Local Call : 1 Rupee per Minute.
STD : 1.5 Rupees Per Minute
International calls : 5 Rupees Per minute
hour = itabcallmast-CALLDURATION+0(2).
min = itabcallmast-CALLDURATION+2(2).
sec = itabcallmast-CALLDURATION+4(2).
CASE itabcallmast-calltype.
WHEN 'L'.
    CALL_CHARGE = ( ( hour * 60 * 60 ) + ( min * 60 ) + ( sec ) ) / 60.
WHEN 'S'.
    CALL_CHARGE = ( ( ( hour * 60 * 60 ) + ( min * 60 ) + ( sec ) ) * 2 ) / 60 .
WHEN 'I'.
    CALL_CHARGE = ( ( ( hour * 60 * 60 ) + ( min * 60 ) + ( sec ) ) * 5 ) / 60   .
ENDCASE.
CALL_CHARGE_STRING = CALL_CHARGE.
TOTAL_CHARGE = TOTAL_CHARGE + CALL_CHARGE.
    CALL FUNCTION 'WRITE_FORM'
     EXPORTING
       element                        = 'MAINPAGE'
       function                       = 'SET'
       type                           = 'BODY'
       window                         = 'MAIN'
IMPORTING
PENDING_LINES                  =
EXCEPTIONS
ELEMENT                        = 1
FUNCTION                       = 2
TYPE                           = 3
UNOPENED                       = 4
UNSTARTED                      = 5
WINDOW                         = 6
BAD_PAGEFORMAT_FOR_PRINT       = 7
SPOOL_ERROR                    = 8
CODEPAGE                       = 9
OTHERS                         = 10
    IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    ENDIF.
ENDLOOP.   " ************ itabCALLmast
CALL FUNCTION 'END_FORM'
IMPORTING
RESULT                         =
EXCEPTIONS
UNOPENED                       = 1
BAD_PAGEFORMAT_FOR_PRINT       = 2
SPOOL_ERROR                    = 3
CODEPAGE                       = 4
OTHERS                         = 5
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
clear itabcallmast.
ENDLOOP.   " ************** itabCUSTmast
CALL FUNCTION 'CLOSE_FORM'
IMPORTING
RESULT                         =
RDI_RESULT                     =
TABLES
OTFDATA                        =
EXCEPTIONS
UNOPENED                       = 1
BAD_PAGEFORMAT_FOR_PRINT       = 2
SEND_ERROR                     = 3
SPOOL_ERROR                    = 4
CODEPAGE                       = 5
OTHERS                         = 6
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.

hi
good
check the following things-
1- Check the value for the field in the particular table,
2- Check the data you r passing from the driver program and the field that is printing the value in the sapscript screen.
3-check in the debug mode when the value is printing in the first row.
thanks
mrutyu

The poor quality outcome from project to .mov

first of all, here is my spec:
running on : win 7- 64bit
processor : core i5 [email protected]
RAM: 4GB approximately
graphic card: ATI Radeon HD 4600 series 1GB
BIOS: version: 08.00.15
using AE CS5, installed with quicktime 7.7, K-lite 7.5.8(update version)
well, the problem is when i was add my project to render queque, the video quality is very good,however the sound is horrible
it's kinda some lag on it whenever i played it with several different video player.
Moreover, when i was attempting to convert it (with full license video converter such as AVS&Any Vid Conv) to avi,mkv. whatever the setting is, the result have no more lag,but THERE WAS NO AUDIO AT ALL.
I rendered it to .mov file( compression type "photo-JPEG") and i also checked a check box of audio output( 48.000KHz-32 bit-stereo)
the project is about only 27 second!
sum1, help me please!!

ooww ya, one thing
i just switch into windows XP SP3, i have dual booth on my PC
Inside XP, there are AE CS4 and then i tried to render the broken video .mov(800MB) into the same setting (.mov & 48.000KHz -16bit-stereo& compression "photo-JPEG"). my XP was installed with quicktime 7.3.1.70 and XP codec pack( not K-lite codec pack)
the outcome performance is pretty good, NO LAGS,no glitches .but somehow, the video size was decreased dramatically (200MB). what's going on actually? is the source in CODEC? thx b4

Analog capture into DV format. Why such small files? Why the poor quality?

I am capturing 8mm video cassettes with an "ADVC 3000" converter, using an S-Video into the converter and then via FireWire into my PowerMac G5.
All is almost going well, but the files seem to take up so little space on my Hard Drive. That's a good thing, but I'm wondering if it's recording into Digital Video or not since the files seem so small. Smaller than normal for DV at least, or maybe I'm just paranoid.
In the scratch files, when I press Command-I for information, the Codecs on the QuickTime files are DV/DVCPRO-NTSC, Interger (Big Endian), Timecode.
So I'm guessing they are DV files even though they look like crap.
My question is this though. When I put these old analog tapes on iDVD, burn it, and put it in my DVD player, the quality of my video looks pretty crappy on my hi-def television. But when I watch them on my computer in a tiny window (the tinier the better), the video looks great. A large window, or my Television, gives a bad picture. My theory is that it's my hi-def television and computer monitor, and that on an old Analog TV set, the videos would look much sharper.
Should I play 8 mm analog video, converted to DV in Final Cut Pro, on an older Analog T.V. set for best viewing results?
Anyone have any comments to share on the science of this?

Yoshiman,
Forgive me if you did know this, the TBC is a Time Base Corrector. (I am pretty sure corrector is right). Anyway, the 8mm has time code striped on it with the image information. If the playback device is not able to read the time code, the picture quality suffers. (remember tracking adjustments?).
The TBC will intercept the time code coming from the tape and provide accurate, consistent time code to the system. I use one from DataVideo, and have been happy with it whenever I have to work with old tapes. If you have a lot of tapes to capture, you might look into one.
My two disclaimers: this is a very general explanation, I simply don't know the physics of what's going on, and secondly I am not a power user of FCS, but have gotten so much from this forum I am trying to give a little back. Take what I bring to the table with that in mind - I'm proficient, but not an expert.

Ever claiming for the poor quality of mackeeper software. It is a scam.

Ever claiming for the worst quality of mackeeper software. It is a scam.

Follow these instructions to uninstall MacKeeper. They have been tested with the most recent version of MacKeeper (v 2.8). Earlier versions than the one released in 2012 require more extensive work to uninstall all its components.
If you used MacKeeper to encrypt any files or folders, use MacKeeper to un-encrypt them first.
Quit the MacKeeper app if it is running.
Open your Applications folder: Using the Finder's Go menu, select Applications.
Drag the MacKeeper icon from your Applications folder (not the Dock) to the Trash.
You will be asked to authenticate (twice):
You do not need to provide a reason for uninstalling it:
Just click the Uninstall MacKeeper button. You will be asked to authenticate again.
After it uninstalls you may empty the Trash and restart your Mac. All that will remain is an inert log file that does nothing but occupy space on your hard disk.

Poor Quality when printing envelopes on P1102W

I have a good toner and it prints good using standard paper but whenever I print envelopes the quality is very bad. Text is very light and has a fading in the middle of text. This is using the manual tray and seems to only happens with envelopes. I'm using MS Word 2010 to print the envelopes.
And...it's not the type of envelopes I'm using because if they print out fine on a different printer.
This question was solved.
View Solution.

This issue likely deals with the thickness of the envelope, which is more dense than normal printing paper. To compensate for this I would recommend going to the Devices and Printers folder and right-clicking on the printer. Here select "Printing Preferences." Under Paper/Quality you can change the printer to print in "Best Mode" which should improve your overall performance on those kinds of print jobs.
Do this and let me know how it turns out!
Have a great day!

Help w/poor quality when printing layout that has a pdf in it to PDF

the problem i am having is plotting from autocad - I have also posted this on an autocad forum but my hunch is that this is an acrobat problem, when I preview the plot everything looks good. What comes out though is a low-res raaster which ilegible. The layout contains a pdf in it and it is this portion that does not look good. I have explored through all the oiptions I can find but nothing has worked thus far.
Can anyone help on this? thanks!

Yes you're right. it's just complicated since there are so many settings within the acrobat plot options.
the pdf that i insert in the layout are made up text and line work, one coming from excel, the other from word. They look good on screen and preserve their vector qualities. I have tried wherever I could find within autocad to change the pdf version to the latest possible...I have also tried removing any compression etc

I am having problems with the image quality when image placing in indesign

Hi
I am finding that many illustrations are pixilating when I place them in indesign from illustrator or photoshop. Some times I can rectify the issue by increasing the size or dpi of the image prior to placement, but I'm sure there must be another way. How can I improve on the quality and definition of placed images in Indesign?

This forum is actually about the Cloud, not about using individual programs
If you start at the Forums Index http://forums.adobe.com/index.jspa
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says ALL FORUMS) to open the drop down list and scroll
http://forums.adobe.com/community/indesign
http://forums.adobe.com/community/illustrator
http://forums.adobe.com/community/photoshop

What's with the poor quality when exporting a presentation to iDVD

When I exported I choose high resolution preference. The presentation ran perfectly in Keynote, but when I exported it to iDVD it looked horrible- like low res- the same when I burned it onto a DVD just as a test. Also, when I tried another route- exporting to Powerpoint it saved the file as .pps? What is that? None of my others have done that.
G4 Powerbook 17in Mac OS X (10.4.5)

I have iDVD 6 and I exported it - high quality to iDVD. Is that what you mean by iDVD feature?
I read on this discussion something about the slide resolution. I discovered when I first set up the show my resolution was 800x600 and I haven't found a way to change it. I am ready to begin again and set my slide res to the maximum and copy, paste, and resize all my text to fit- then export again. LOTS OF WORK! but I am not sure how else I can resolve this.

I have a problem with the sound quality of skype

My skype is working okay. I never had a problem before today.
I can hear the other person but they can't hear me. I checked
my sound and audio settings. I unclicked the mute on microphone but it keeps reclicking itself. I did the test call which I never had a problem but I can't hear myself or it is really low. I am not sure if its a windows xp problem or firefox. I just want my microphone to work again like it did a few days ago.

Define "voice of the device."
Are you referring to the ear speaker or main speaker? Phone calls? Rings/alerts? Music?
What troublshooting steps did you take?

Problem of the poor quality of print as booklet

Similar Messages

Maybe you are looking for