Problem on installing Solaris 10 on Cisco UCS-C24-M3S2 rack server.

I've got issue on installing Solaris 10 on Cisco UCS-C24-M3S2 rack server. Solaris 10 doesn't recognize UCSC-RAID-ROM55.

Hi dipaktimsina,
From the documentation below it looks like Solaris doesn't have support for the embedded raid controller with the ROM55 chip.
http://www.cisco.com/web/techdoc/ucs/interoperability/matrix/matrix.html
let me know if you have any questions and don't forget to rate any useful answers.

Similar Messages

Problem facing installing Solaris 10 on Dell inspiron 6400.

Hi,
I am facing problem in installing Solaris 10 on my Dell inspiron 6400.
It is giving "cannot find driver for screen device /isa/motherboard@1,61" error.
Please help...
Thanks In Advance
Saurabh

Hi all,
I've also the same problem, I tried the 11/06 but after GRUB , it hangs. HereBelow the HCL.
No Solaris Driver
     No Solaris Driver
     Multimedia
     Intel Corporation
     82801G (ICH7 Family) High Definition Audio Controller
No Solaris Driver
     No Solaris Driver
     Network
     Intel Corporation
     PRO/Wireless 3945ABG Network Connection
Solaris 10 11/06
     Solaris 10 11/06
     Firewire
     Ricoh Co Ltd
     Unknown device
     hci1394
Note-1
     Note-1
     Network
     Broadcom Corporation
     BCM4401-B0 100Base-TX
     bfe
Solaris 10 11/06
     Solaris 10 11/06
     Video
     Intel Corporation
     Mobile 945GM/GMS/940GML Express Integrated Graphics Controller
     vgatext
Solaris 10 11/06
     Solaris 10 11/06
     Storage
     Intel Corporation
     82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE
     pci-ide
Solaris 10 11/06
     Solaris 10 11/06
     USB
     Intel Corporation
     82801G (ICH7 Family) USB UHCI #1
     uhci
Solaris 10 11/06
     Solaris 10 11/06
     USB
     Intel Corporation
     82801G (ICH7 Family) USB UHCI #2
     uhci
Solaris 10 11/06
     Solaris 10 11/06
     USB
     Intel Corporation
     82801G (ICH7 Family) USB UHCI #3
     uhci
Solaris 10 11/06
     Solaris 10 11/06
     USB
     Intel Corporation
     82801G (ICH7 Family) USB UHCI #4
     uhci
Solaris 10 11/06
     Solaris 10 11/06
     USB
     Intel Corporation
     82801G (ICH7 Family) USB2 EHCI Controller
     ehci

Problem while installing solaris 10 on HP proliant DL 380 G5.

Hi,
facing problem while installing solaris 10 05/09 on HP proliant DL 380G5. The array controller is E200.
i have installed the raid controller driver CPQary3-2.1.0-solaris10-i386, it is going ahead but not detecting the whole hard disk space. My hard disk space is SAS 146GB. There are two 146GB hard disk present. It is showing only 978 MB & only one hard disk. So please help me out. my mail ID is [email protected]

I have a similar issue trying to load Solaris 10u4 on an IBM x236.
I had to put in a recognized SCSI card, attach an external array to the card, and install Solaris 10u4 on the array. Then I had to install the correct driver from OpenSolaris (an Adaptec one for IBM ServeRAID), and do a live upgrade onto the now-visible internal disks. Then I removed the array and cleaned up the traces from the live upgrade.
You may have to do something similar.
And last month the boot drive got corrupted when power was interrupted. "Oops. Wrong plugs..." This time the external array will stay connected.

Problem to install SAP R/3 4.6 on Windows server entreprise 2003

Hello all,
I've a problem to install SAP R/3 on a windows enterprise server 2003.
This is the step I made :
1) Install Windows enterprise server 2003
2) Add IPX and Netbios to the network (adress ip 192.168.10.2)
3) Add 192.168.10.2 srv1 SAPTRANHOST to the hosts file
4) Create User - C11adm; Assign administrator privileges
5) Start Update DLL's from Kernal CD.
6) Login as c11adm and Install Oracle 9.2 with the options :
File locations :
Source :
      Path : no change the path
Destination :
      Name : C1192
      Path : C:\oracle\C11\92
Available Products :
      Oracle9i Database 9.2.0.1.0
Installation type :
      Enterprise Edition
Database configuration :
      General Purpose
Oracle service for Microsoft Transaction server
      Port number : 2030
Database Identification :
      Global database name : srv1
      SID : srv1
Database File location :
      c:\oracle\oradata
Database charactere set :
      Use the default charactere set
7) Stop all oracle services
8) Install oracle 9.2.0.4.1 patch :
    OUI - V 2.2.0.18.0
    Oracle 9iR2 patch set 9.2.0.4.0
9) Install SAP R/3 disc 4.6D EXT Kernel
    INSTGUI options:
    Sap system name : C11
    Install Directory : C:\USERS\C11ADM\Install
    Sap Release to install : R/3 4.6C SR2
Error : CDINSTEXTRACTSAPMMCMSC_NT_IND InstallationDo 2342
Does somebody could help me ?
Regards.
4. Give all users access to ora_dba
5. Restart, login as c11adm and continue installation.

Hello Peter,
For the note 578004 Sap said :
            a) Copy the content of the respective Kernel CD to a local empty working directory.
                       For example, for a 4.6C SR2 system you use the 4.6C SR2 Kernel CD, for APO 3.0A you use the Kernel CD for APO 3.0A, etc.
But for myself, i don"t understand what they said because I Want to install 4.6c and they said "use the 4.6c SR2 Kernel CD" but where I can find this CD because I downloaded the files below :
50045631_1     Online Docu 4.6C Disc 1 HTML Help Windows 9x/NT German
50045631_2     Online Docu 4.6C Disc 2 Standard HTML German
50045631_3     Online Docu 4.6C Disc 1 English HTML Help for Windows 9x/NT
50045631_4     Online Docu 4.6C Disc 2 English Standard HTML
50046529     R/3 4.6C SR2 Installation Documentation
50056848_1     DVD 4.6C Online Documentation (3) 1 of 11
50056848_10     DVD 4.6C Online Documentation (3) 10 of 11
50056848_11     DVD 4.6C Online Documentation (3) 11 of 11
50056848_2     DVD 4.6C Online Documentation (3) 2 of 11
50056848_3     DVD 4.6C Online Documentation (3) 3 of 11
50056848_4     DVD 4.6C Online Documentation (3) 4 of 11
50056848_5     DVD 4.6C Online Documentation (3) 5 of 11
50056848_6     DVD 4.6C Online Documentation (3) 6 of 11
50056848_7     DVD 4.6C Online Documentation (3) 7 of 11
50056848_8     DVD 4.6C Online Documentation (3) 8 of 11
50056848_9     DVD 4.6C Online Documentation (3) 9 of 11
50078731_1     NW 2004s SR1 Presentation - Adobe LiveCycle Designer 7.0
50078731_2     NW 2004s SR1 Presentation - SAP Content Server 6.40
50078731_3     NW 2004s SR1 Presentation - MaxDB Release 7.6.00
50078731_4     NW 2004s SR1 Presentation - 6.40 Compilation 5 Present. 1/3
50078731_5     NW 2004s SR1 Presentation - 6.40 Compilation 5 Present. 2/3
50078731_6     NW 2004s SR1 Presentation - 6.40 Compilation 5 Present. 3/3
50078731_7     NW 2004s SR1 Presentation - Server Components Compilation 5
50081125     CD SAP License Keys & License Audit
51013953_1     R/3 4.6C SR 2 Export CD 1
51013953_2     R/3 4.6C SR 2 Export CD 2
51013953_3     R/3 4.6C SR 2 Export CD 3
51013953_4     R/3 4.6C SR 2 Export CD 4
51013954_1     R/3 4.6C SR 2 Language CD 1
51013954_2     R/3 4.6C SR 2 Language CD 2
51013954_3     R/3 4.6C SR 2 Language CD 3
51013955     R/3 4.6C SR 2 Language JA
51013957     CD 4.6C SR2 Language TH
51013998     R/3 4.6C SR 2 Language ZF
51018621     CD mySAP.com 4.6C Language Romanian
51019432     CD Oracle9i Database Onl. Docu. 9.2
51019883     CD 4.6D SAP Kernel ORACLE NT/IA64
51020564     CD 4.6D EXT Kernel ORACLE NT,AIX,HP-UX
51030122_1     Oracle 9.2 NT 1/3
51030122_2     Oracle 9.2 NT 2/3
51030122_3     Oracle 9.2 NT 3/3
51030122_4     Oracle 9.2.0.4.1 NT
51030122_5     Oracle Failsafe 3.3.2 NT/Intel
51030123_1     Oracle 9.2 NT/IA64 1/2
51030123_2     Oracle 9.2 NT/IA64 2/2
51030123_3     DVD ORACLE RDBMS 9.2 NT/IA64
51030123_4     DVD ORACLE RDBMS 9.2 NT/IA64
51030123_5     Oracle Failsafe 3.3.2 NT/IA64
51031095_1     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 1 von 12
51031095_10     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 10 von 12
51031095_11     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 11 von 12
51031095_12     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 12 von 12
51031095_2     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 2 von 12
51031095_3     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 3 von 12
51031095_4     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 4 von 12
51031095_5     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 5 von 12
51031095_6     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 6 von 12
51031095_7     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 7 von 12
51031095_8     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 8 von 12
51031095_9     DVD Supp.Pack.Coll. 4.6C-47x200 2005/06 9 von 12
51031592     CD SAP R/3 4.6C SR2 Language KO
51031593     CD SAP R/3 4.6C SR2 Language ZH
51031614_1     Oracle 9.2 Patch Set 7 AIX 64 64Bit
51031614_2     Oracle 9.2 Patch Set 7 Tru64 64Bit
51031614_3     Oracle 9.2 Patch Set 7 HP-UX PA-RISC 64Bit
51031614_4     Oracle 9.2 Patch Set 7 Linux I386 32Bit
51031614_5     Oracle 9.2 Patch Set 7 WIN I386 32Bit
51031614_6     Oracle 9.2 Patch Set 7 WIN IA64 64Bit
51031614_7     Oracle 9.2 Patch Set 7 Solaris 64Bit
51032345     Supp.Pack.Coll. 4.6C-47x200 2006/12
Regards.

Strange problems after installing Solaris 10 u6 on 64-bit PC

Hi all,
I have run into some very strange issues after installing Solaris 10 update 6 on my 64-bit PC (it's almost new). The problems are with graphical applications and desktop environments based on GTK (so it seems, at least).
I have installed Solaris normally, following most of the default options and choosing the "Entire Group" software packages installation. However, after the first login I've seen that:
1. No user creation process was offered to me and I had to login as root (I find it pretty strange)
2. After logging in as root into JDK system, my screen went blank for a couple of seconds and then the system threw me back to the login screen.
3. Logging into the old CDE environment was possible, but launching Firefox from there (using a command line terminal) wasn't. It gave me the following error message:
ld.so.1: firefox-bin: fatal: libmlib.so.2: open failed: no such file or directory
ld.so.1: firefox-bin: fatal: relocation error: file /usr/bin/firefox/firefox-bin: symbol gtk_init: referenced symbol not found.
It's very strange because GTK toolkit and JDK environment are supposed to be the core functionalities provided by Solaris. Does anyone have an idea what's going on?
My system sum-up:
CPU: Intel Core 2 Quand Q6600 @ 2.4 GHz
RAM: 2 Gb of DDR2 SDRAM
Motherboard: MSI MS-7529 (Intel G31 chipset)
Monitor: AOC LM725
Graphics card: NVIDIA GeForce 9400 GT
Hard disk: 2 Western Digital HDs (SATA) 320 Gb each,
1 Western Digital external USB HD MyBook Essential 2, 500 Gb
DVD drives: 2 LG DVD drives (SATA)
Network card: Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC
I use my system in the following way:
On the first hard disk, I have a one-partition 32-bit Windows XP SP3 installation (ported from my old computer).
On the second hard disk, I have a functioning Fedora Core 9 installed on the first half of the disk's space (the installation is self-organized into several Linux partitions, e. g. /boot, /swap etc; I am a newbie so I don't know too much about Linux partitioning - only specified to Fedora how much space it could use for its volume group). I installed Solaris onto the second half of the second disk.
It has be noted that my USB external drive seemed to conflict with the network or graphics cards during the Fedora installation and caused it to hang sporadically, so I installed Fedora with this disk detached. I also detached it when I was installing Solaris, though it seems to have not influenced the problems I experienced. I also have attempted installing Solaris before I did so with Fedora, but had the same issues.

Well, it seems that the cause of the problem was that my DVD image was just corrupted - I didn't check it vs MD5 codes supplied by Sun assuming it went automatically OK. I downloaded the image again (this time it was OK), reinstalled the system and successfully logged into JDS. However, I am still puzzled why Solaris doesn't offer to create a default non-root user during the installation process.

Problem when installing Solaris 10

I've read that there is a post with the same problem I have, but I found no solution there.
So I made this tread, hoping someone willing to help me.
OK, here is the story...
I have tried several times to install Solaris 10, from DVD to my laptop Dell Latitude C400.
(I've run the hardware compatibilty check routine, and it's OK except the video card)
After I made the partition, then rebooted using the DVD and the Solaris seems to load normally.
It apperas the Grub menu, then I choosed Solaris option.
But after that it just stops on a screen that says:
SunOS Release 5.10 Version Generic_118844-26 32-bit
Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
And it just hangs, nothing more...
Any idea what should I do to install Solaris successfully...???
Thanks in advance

Hi Darren,
Thanks God I've succesfully installed Solaris 10 to my laptop, after "swimming" for a while in google :)
It said that this was a bug of Solaris 10 when installed in PC with Pentium III or II processors.
Here is the solutions (hope someone with same problem with me could find it useful) :
1. After the GRUB menu appears, edit the kernel line then append -kd at the end (to enter kmdb upon boot), then boot
2. Then type this command when kmdb prompt shows, [0]>
[0]> cmi_no_init/W1
[0]> :c 3. It should boot and run without problem, then follow the installation menu and option
4. After reboot, again follow step 1 & 2 when GRUB menu shows. I promise this is the last time :)
5. To make it permanent, add this following instruction to */etc/system* once the system up
set cmi_no_init=1//Henry

Problem of installing solaris 8

I got the following warning message when I install Solaris 8(Intel x86) on
my PC(Abit KT7 motherboard, AMD Duron 650 CPU, NVIDIA RIVA TNT2 Model 64
display adapter) from bootable CD-ROM.
Determing bus types and gathering hardware configuration data...
Warning: Resource Conflict- both devices are added
Non-ACPI device: PNP0C01
Memory: FFFE0000-FFFFFFFF, FEE00000-FEE0FFFF
ACPI device: PNP0C01
Memory: CA800-CBFFF, 1FFF0000-1FFFFFFF, FFFF0000-FFFFFFFF,
9FC00-9FFFF, 40F0000-1FFEFFFF, FEE00000-FEE00FFF
Then I ignore the message, press ENTER key to continue. Everything seems ok, but when it boot the SunOs(even not begin to install), it restart
my computer without any prompts. I try to install it again, but the same
restart happened again .
I think the problem maybe result from the motherboard or display adapter.
Could you tell me how to resolve it?
my email: [email protected] I'm looking forward to hearing from you.
Thanks for your time.
Best regards,
Charles Mao

I am having the same problem with an ASUS K7M and Athlon 550, but only after I fixed(!) the conflicting addresses in the Windows device manager. Win95 had also reported the same conflicting addresses before but I fixed it by deleting the PnP device and rebooting - Windows assigned new non-conflicting addresses. Solaris boot was still showing the conflict but now also crashed as you described.

Problem in installing solaris 10 in sun blade 1000

Dear all,
I am trying to install solaris 10 in sun blade 1000 and getting a problem that disk doesn't exist ......... After several tentatives, I understood that I need to format a harddrive as it is new. I formeted it with boot cdrom -s and the problem still persists.
I bought a 73g HDD and the machine recognize it as 68,38g .. is there any upgrade I need to perform for it
Could someone please help me to solve this problem
Thanks a lot for your help and reply ...

I have the same problem ..ubuntu installs fine
TIA
Dale

Out Of Frequency problem -- After Installing solaris 10 x86

Hi Solarians,
After installing solaris 10, I am getting "*Out Of Frequency*" problem and I am not able to login to Desktop session. Please let me know configuration changes that i need to make along with exact paths as i am new to solaris.Currently i am running dual OS (XP and Solaris).
Out of Frequency
HF: 42.7 KHZ
VF: 40.0 HZ
Operating Frequency
HF: 30 - 71 KHZ
VF: 50 - 160 HZ
Please help me solve this problem, Thanks in advance .....
Thanks,
Mahesh

hi;
I faced that problem when I was a beginner on solaris as you were. I tried to install solaris to my windows installed x86 based PC. in my fisrst few attempts ý always saw that message, afterwards somehow I managed to install solaris to my PC but this time windows failed.I think that is because of the inconsistencies between those OS but if you need to install solaris you can use VM ware workstation with this software you can use both OS without problems.

Hard disk problem after installing Solaris 10 u5 on a Sun Ultra 24

Hi.
After receiving a new Sun Ultra 24, shipped with Solaris 10 u4, the first thing I did was installing Solaris 10 u5. X wouldn't start but that was not a big problem and installed it in text mode. Installation went fine but, when the system starts, a single beep is heard and after some seconds some warning message appear on the console, before the "Hostname: ..." message, informing that some read operation on my hard disk had timed out and were aborted. The system then starts up normally. The only other anomaly is that the diagnostic partition in unbootable.
I ran the hard disk tests from the tools and drivers CDs and all of the tests were passed. Solaris 10 u4 was working normally so I'm wondering if this may be a bug.
Thanks for your help,
Enrico.

Thanks anyway, I discovered what the problem was: a bug in Solaris 10 u5:
http://opensolaris.org/jive/thread.jspa?threadID=58768&tstart=75
http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6536722
Thanks,
Enrico

Problem in installing Solaris 10 under VMware

I am installing Solaris 10 under VMware (VMware ESX 2.5.1) but after it skipped configuring the interface pcn0, nothing comes up on my window again.

help me!
I have them same problem!
Thanks!

Problem when installing Solaris 7

Hi, I face a problem just the same as what Geraldin did, no-VTOC, except that I install from CD-ROM:
when I installed Solaris 7, I've got an error that it was unable to mount a root file: CD.
What is it? Am I need to delete all partitions using fdisk just like Geraldin, before installing Solaris?
Thanks.

Hi Darren,
Thanks God I've succesfully installed Solaris 10 to my laptop, after "swimming" for a while in google :)
It said that this was a bug of Solaris 10 when installed in PC with Pentium III or II processors.
Here is the solutions (hope someone with same problem with me could find it useful) :
1. After the GRUB menu appears, edit the kernel line then append -kd at the end (to enter kmdb upon boot), then boot
2. Then type this command when kmdb prompt shows, [0]>
[0]> cmi_no_init/W1
[0]> :c 3. It should boot and run without problem, then follow the installation menu and option
4. After reboot, again follow step 1 & 2 when GRUB menu shows. I promise this is the last time :)
5. To make it permanent, add this following instruction to */etc/system* once the system up
set cmi_no_init=1//Henry

Problem with installing solaris 10

hi.
I'm using Intel-based processor for my stand-alone computer running Windows XP Professional with a broadband connection.
As directed by one of the guys here, and also by my own research, I found the documentation for installing Solaris 10 on x86 based computers.
By navigating through the documentations:
'Solaris 10 Release and Installation Collection' >
'Solaris 10 Installation Guide: Basic Installations' >
'2. Installing With the Solaris Installation Program (Tasks)' >
'x86: Performing an Installation or Upgrade With the Solaris Installation Program'
I followed the instructions as stated in the documentations and set BIOS to boot from CD.
It didn't worked. My computer went on to boot from my Windows OS located in my hard disk. (CD is my first boot device in BIOS)
I have 4 CDs now for Solaris 10 installation.
Each of the CD has a ISO file respectively.
Please help!

One or more of the following:
(A) Your motherboard and/or CD-ROM drive do not actually allow booting from CD even though all of the settings seem to be set correctly. I've had this happen to me before. Try a different CD-ROM drive.
(B) Your CDs are written from bad ISO images.
(C) Your CD writing software does not properly create bootable CDs. If you use Windows, Nero is highly recommended.
(D) Your CDs were written too fast. Rewrite the CDs using the slowest speed that your CD writer will allow.

Problem with installing Solaris Express Community Edition(Virtual Machine)

When I start my virtual machine to install Solaris Express Community Edition(X86 edition), it just displays an character interface
grub>
and there is no other useful information, so I don't know what to do next, does anyone can help?

Try seting "-jdkhome xxxxxxxxxx" in the ide.cfg file in your Forte \bin\ directory. Point it to the SDK install directory - that is, make "xxxxxxxxxx" the path to the SDK install.
You seem to be accessing a java.exe that is pointing to a location that is other than where jvm.dll is residing. This may get you to executing the correct java.exe.

UCS C220 M4 rack server extremely noisy

Hi,
I am preparing a UCS C220 M4 with windows 2012 for a client.
The server is extremely noisy, I mean much more than any other rack server I have ever seen.
All the fan are working at highest speed rate as if the server had to urgently cool down.
The question is: Is this normal ? Is the server broken ? Is there an option to lower the "fan-policy".
And how is this done.
Best regards,
Javier Conejo

The fan policy can be lowered if you go to the Server> Power Policies> Fan Policy.
Here is the explanation for each option:
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/sw/gui/config/guide/1.5/b_Cisco_UCS_C-series_GUI_Configuration_Guide.151_chapter_011.html#concept_8CB787DF70304E98BE25D120466418B9
Balanced This is the default policy. This setting can cool almost any server configuration, but may not be suitable for servers with PCIe cards, since these cards overheat easily.
Performance This setting can be used for server configurations where maximum fan speed is required for high performance. With this setting, the fan speeds will run at the same speed or higher speed than that of the Balanced fan policy.
Low Power This setting is ideal for minimal configuration servers that do not contain any PCIe cards.
High Power This setting can be used for server configurations that require fan speeds ranging from 60 to 85%. This policy is ideal for servers that contain PCIe cards that easily overheat and have high temperatures. The minimum fan speed set with this policy varies for each server platform, but is approximately in the range of 60 to 85%.
Maximum Power This setting can be used for server configurations that require extremely high fan speeds ranging between 70% to 100%. This policy is ideal for servers that contain PCIe cards that easily overheat and have extremely high temperatures. The minimum fan speed set with this policy varies for each server platform, but is approximately in the range of 70 to 100%.
There are still some PCIe cards that cannot be monitored and cause the policy to be "ignored" so the server can be kept cool (I'm not saying that is your issue, I am just mentioning it)
Open an SSH session and enter the commands:
"connect debug-shell"
"sensors"
Paste the output here for the FAN sensors (they will have the word "FAN" on it)
Be sure you air flow is not blocked at all by doors or cables.
-Kenny

Problem on installing Solaris 10 on Cisco UCS-C24-M3S2 rack server.

Similar Messages

Maybe you are looking for