Problem recording from dec

Hi folks. Wondered if you can help. I regulary record my DJ mixes to pop on CDs and the like. I recently got a soundblaster li've external box ting and have plugged a cable from the record out from my mixer to the line in jack to the sound box. Im getting no sound from the speakers and?im unable to record. Does anyone have any ideas?. Any help would be appreciated... Thanks.

Stupid me!!!. Had line in muted!!!!

Similar Messages

Problem recording from external l

I'm new here, I have a SB Audigy 2ZS, and I want to record from external line to my PC.
I use a external mixer to connect cassette, mics, long plays to the PC, and I connect them to SB Audigy from "Input line". And I use the mixer to amplify the PC. When I want to record the "surround Mixer" software thas not permit select a simple record input, it mixer all lines (wave, CD, CD digital, input line).
That produce a terrible feedback. Are there some way to record only from input line, without switch line by line?
Thanks
Mduque

Just click on the speaker icon under the volume controls in the mixer. Having said that it is not really necessary as I am unable to detect any hum by leaving them open. I suspect you may need to reinstall the card.

Problem recording from Line-in (Audio Control Pod)... NOT THE TIPICAL OBVIOUS PROBLEM (I think X

Hi guys!!
I have a little problem and i have think you could help me...
I'm trying to connect my electric guitar to my Audigy 2 ZS... My problem is that i connect the AMPLIFIED output of my guitar to Line-In in Audio Control Pod of my T7700 speakers... I Can hear the what i'm playing from my speakers but I can't record anything... I check all the obviuos things, like I have selected Analog Mixer (Line/CD/TAD/...) from Surround Mixer Tab drivers (Rec tab) and in Control Panel of Windows too. What am i doing bad?...
Thank you for your help!

May have already been answered, but, hey, what the heck, I've got free time:
Allow me to clarify. Plug your guitar into the Line-In on your <EM>sound card</EM>. Plugging it into your speakers only uses your speakers as an amp.
Then, in Creative Recorder select Line-In as the source.
Speakers, unless they're plugged into the mic jack on your sound card (which they shouldn't be), do not transmit data back to the PC.
EDIT: Line-in is this thingie (( )) with an arrow pointing inside.Message Edited by ghostrecon09 on 02-22-2005 05:4 AM

Problems recording from my camcorder to fcp

Hi
I wonder whether anyone else has experienced this problem and can help?
Due to a shortage of funds I am using my Canon HV30 camcorder to put a voiceover onto my fcp film. This worked fine the first time but now when I try and use it I get the message
'The selected input device is unavailable, it may be in use by another application etc etc.'
I have checked under About this Mac and firewire and my camcorder is present.
I have tried unplugging everything, turning off the imac, removing all the cables and rebooting and then putting all the cables back in.
And starting up fcp with the camcorder already on (and starting up fcp with the camcorder set to off and then putting it on)
Version of FCP is 6.0.4
I have the audio/video settings set to
Seq preset HDV 108050I
Capture present HDV
Device control firewire basic
Under the A/V devices tab I have settings
Playback output none
the different output for edit to tape/print to video box is checked
video HDV 1440x1080) 50i (I'm based in the UK)
Are my settings correct for using my cam as a mic?
I have tried using both camera mode and playback mode to tape - neither work.
If my audio/video settings are correct - should I try trashing the FCP preference files?

Definitely trash your preferences, and see if that helps. Then, read this post about HDV FCP problems!
http://discussions.apple.com/thread.jspa?messageID=7226946&#7226946
Hope it helps.
Matt

Recording from minidisc to Logic pro 7 via an fa-66

Hi, I'm having issues recording from a sony minidisc deck through my edirol fa-66 to my macbook. I've tried the various anologue inputs on the fa66, the 1/4 jacks and the RCA inputs on the back. With the anologue it's sounds fine until I arm the track to record, then it starts jumping and phasing. Same with the optical input, I press the "Digital sync" on the fa-66, without the "R" record armed it sounds fine, when I arm it the sound starts jumping and a message comes up "saying sample rate not recognised- Sample rate 3674"
The minidisc was recorded from a PA at I assume the satndard rate for mnidisc players of 4100Khz.

If you are using the Digital input (SPDIF) to record from MiniDisc then you are correct that it is 44.1Khz, but are you ensuring that the SPDIF input is set as the master clock? You will need to ensure that is so whilst you record digitally from it.
I can't fanthom why you might be have a problem recording from the analogue outs though. The phasing sound you describe sounds like you are hearing the original sound plus the slightly delayed sound due to software monitoring perhaps?

Recording from minidisc to creative player with an x

I tried recording from my?minidisc onto my computer with the x-fi card, through the line-in and mic jacks. When I stop recording and turn off the source, I still have the record volume showing some input even though nothing is on. I?even?tried disconnecting the minidisc from the input jack but the player is still showing some input. This is causing my recording to have a steady interrupting noise every quarter of a second or so. Any ideas where to search for this mysterious input or how to get around this problem.Louis?

If you are using the Digital input (SPDIF) to record from MiniDisc then you are correct that it is 44.1Khz, but are you ensuring that the SPDIF input is set as the master clock? You will need to ensure that is so whilst you record digitally from it.
I can't fanthom why you might be have a problem recording from the analogue outs though. The phasing sound you describe sounds like you are hearing the original sound plus the slightly delayed sound due to software monitoring perhaps?

Selecting Records from one table where records don't exist in a linked table

Post Author: RMC
CA Forum: Crystal Reports
Tables:
Stock (Main Table)
Transactions (Left Outer Join)
Criteria:
Select all items with no transactions between a selected date range.
The items will exist in Main table but I want to select all items that haven't been in a transaction between a date range so I can identify no movement with stock items just sitting in the database doing nothing.
Any suggestions??

Post Author: yangster
CA Forum: Crystal Reports
Sorry for the delay. Dam meetings all day yesterday.You are essentially looking for something that doesn't exist in the db so you need to look at it from a different approach.You definitely don't want to use a full outer join. From what i can tell from your description above you are looking for stocks that are inactive/idle.So you need not look at data that doesn't exist but the last activity date.So you'd want something along the lines ofselect s.stock_name, s.stock_blah, max(t.transaction_date) Transaction_datefrom stocks sjoin transactions t on s.itemid = t.itemidwhere whatever restrictions you need to addgroup by s.stock_name, s.stock_blahthis will produce one record for each stock you have in the stock table showing you only the last date of activityput that in a command in crystalin the selection expert in crystal reports put in a simple criteriatransaction_date <= some datethis will only pull in records based on your date selection so if you say give me all records from dec 31, 2006 you will know all the records being pulled in are stocks that have been idle since dec 31, 2006 or earlierlet me know if this doesn't work

Problem recording stereo vocals

i'm having a problem recording from my usual midi input with a Shure stereo microphone.
the system is set for audio input from the midi microphone, and it appears to be recording in stereo (both tracks are visible in the soundwave), but once the record button is stopped, the L track disappears, and only the R track plays and shows up in playback.
i am using the m-audio prokeys sono to route the microphone through -- never had this problem before now.

i shouldn't have said the Shure SM57 was stereo. it's probably mono like all mics. all i'm saying is that i've used it plenty, setting it to stereo, and getting records levels on both L and R channels, and R/L waveforms in the track window.
now the audio only seems to be recording on the L (i had it backwards in the original post), with only the faintest sound and no graphic waveforms on the R.
i could probably "solve" this by recording on the mono 1 (L) channel, but that's not how i did it before, so it's really got me bugged.

Problem when recording from the AUX phono output using creative x-fi elite

Hello everyone?Hopefully someone will be able to help me out here, as I've tried everything, however nothing seems to work. I am using the x-fi elite pro on a windows vista ultimate PC. When recording analogue material, from a tape Dec, for instance, I am using the creative audio console which accompanies the x-fi elite pro. I am using the aux phono input on the back of the box, and everything has gone smoothly until a few days ago. When trying to record from my tape Dec this last week, I suddenly noticed that the sound was very distauted in the left channel. Right channel was fine.Of course the first thing I checked was the level, and this was absolutely fine too, both channels were set to around 50% in the sound-options control-panel. I then checked the cable and then tried it on other equipment as well, and everything was also fine here. I then re-connected it to the audio consul, but got the same results. Fine sounding audio in the right channel, but distauted in the left. I then tryed re-installing the newest vista-driver to see if this would solve my problem, however it didn't. Now I've only got audio in the right channel, but no audio at all in the left. Has somebody inhere experienced anything simurlar, and if yes, can you please tell me what could be wrong??All the best from Allan

On certain mobo/graphics card set ups and some sound cards there is an issue with bus latency. In short while playing back audio you will hear a frequent crackling of the audio. That is not the same as the slight click the Elite pro makes when changing modes. It has been a Creative issue for many years but is only present with certain combinations of hardware. I have experienced that issue myself but several years ago. My current Elite Pro/PC set up does not have this issue.

Problem with Adobe Audition 2.0 and recording from a 1212m.

I bought a brand new machine and have be configuring it all week. Everything has been going well, except getting Adobe Audition 2.0 (the new version) to “hear” sound from the 1212m.
The intel 975 motherboard has an integrated HD sound system already on board and I have been able to get adobe audition to recognize it and record from it. This is what I have Windows XP Pro set to as my default sound card.
I installed the 1212m and I have gotten my monitors to work by using the XLR jacks on the monitors to the ¼ inch jacks on the 1212m using a VST (NI’s Kontakt 2) as the audio source. So it works.
What I can’t seem to get to work is getting Adobe Audition to “hear” the sound coming from the 1212m.
Patchmix seems to be working ok. The audio bars jump each time I hit a note on the keyboard.
I have configured Audition by going to Audio Hardware Setup and setting it to EMU ASIO and tried every combination of INPUT and OUTPUT, but when I hit the Record button in Audition it just flat lines..
I was hoping that once the audio made it from the VST though the 1212m and out to the speakers, that getting Audition to record it would be easy, but that hasn’t been the case.
The Intel 955 Extreme Edition and the 975 motherboard are brand new and I’m worried that being on the bleeding edge of technology, that one of the drivers isn’t working correctly and causing me hours of debugging a problem that is unworkable from my end.
Hopefully the problem is just some small stupid thing that I’m doing or failing to do (like normal).
Any ideas would be helpful.
thanks

I'm just saving it into a file in "My documents" on the internal hard drive. It's a computer in the office which has been used my other people before me and I have my own file which I was always able to save Adobe sound files into before, so I don't think it's anything to do with me not being allowed or read-only.
I've also been trying to save it onto USB hard drives. This works when I save it under a different name, but not when I'm just trying to update a file i've been working on. Basically I have to create a new file everytime I add something, so like "myaudit1", "myaudit2", "myaudit3" etc etc, even though it's the same piece of work just updated.
Hope that makes sense!

Problems importing videos recorded from my iPhone 3GS to iPhoto

I am having problems importing any videos recorded from my iPhone 3GS onto iPhoto. iPhoto keep giving me the following error:
"Error downloading Image. iPhoto cannot import your photos because there was a problem downloading an image."
If anyone else is having the same problem, please advise on how to fix.
Thanks,

I am having the same problem...
and Image Capture ( didn't know we would normally be able to use it, but you can) also give an error
"Import Error"
Now I have used "ITimelapse pro" to transfer some timelapse movies (about 3 that are about 30 to 60 seconds long) that I made to the phone's photo library.. and I has a very long video that I mistakenly made - (15 minutes long or so) and I "trimmed" it to be a few minutes long. -- and used "JotNot" to send a photo to the photo library... otherwise I have only some regular photos (about 40 ) and about 2 regular videos in the library.
so any suggestions... ( I am emailing all that I can to myself ... maybe ridding everything will help)

Problem recording to DVD from DVR

I am having a problem setting the recording speed when recording from DVR to DVD.
When recording directly from the TV (either manually or programmed), I set the recording speed using the REC MODE button on the remote and it works well.
When I record from DVR I set the recording speed the same way but the recording stops after 30 minutes. I was able to get around this by pressing the RECORD button on the set enough times to get it to register the desired speed.
I find this very awkward (and unnecessary). Is there something obvious that I am missing?
Thanks
Solved!
Go to Solution.

I think you might be a little confused.
REC MODE is only for setting speed. Multiple times being pressed keeps changing the recording speed.
REC is only for actual recording. Multiple times being pressed increases the amount of time to record by 30 minutes.

Performance problem with selecting records from BSEG and KONV

Hi,
I am having performance problem while selecting records from BSEG and KONV table. As these two tables have large amount of data , they are taking lot of time . Can anyone help me in improving the performance . Thanks in advance .
Regards,
Prashant

Hi,
Some steps to improve performance
SOME STEPS USED TO IMPROVE UR PERFORMANCE:
1. Avoid using SELECT...ENDSELECT... construct and use SELECT ... INTO TABLE.
2. Use WHERE clause in your SELECT statement to restrict the volume of data retrieved.
3. Design your Query to Use as much index fields as possible from left to right in your WHERE statement
4. Use FOR ALL ENTRIES in your SELECT statement to retrieve the matching records at one shot.
5. Avoid using nested SELECT statement SELECT within LOOPs.
6. Avoid using INTO CORRESPONDING FIELDS OF TABLE. Instead use INTO TABLE.
7. Avoid using SELECT * and Select only the required fields from the table.
8. Avoid nested loops when working with large internal tables.
9. Use assign instead of into in LOOPs for table types with large work areas
10. When in doubt call transaction SE30 and use the examples and check your code
11. Whenever using READ TABLE use BINARY SEARCH addition to speed up the search. Be sure to sort the internal table before binary search. This is a general thumb rule but typically if you are sure that the data in internal table is less than 200 entries you need not do SORT and use BINARY SEARCH since this is an overhead in performance.
12. Use "CHECK" instead of IF/ENDIF whenever possible.
13. Use "CASE" instead of IF/ENDIF whenever possible.
14. Use "MOVE" with individual variable/field moves instead of "MOVE-
CORRESPONDING" creates more coding but is more effcient.

JSF - Problem in Retrieving selected record from datatable

I am new to JSF and in the process of developing a new web application using JSF.
I have problem in retrieving the selected record from a datatable. I am using h:datatable tag and h:commandlink in a column for selecting a particular row on the datatable.
I have populated the data to the datatable by binding a bean and its property.
When I retrieve also I am binding to a bean in the action attribute of the h:commandlink tag in h:column of that datatable.But when I try to bind the bindign attribute of the h:datatable tag to the datatable instance in my Bean , my JSF File gets corrupted..
How to implement this without any issue??plz help me regarding this.

HI
Try the below code
DATA lo_nd_del TYPE REF TO if_wd_context_node.
DATA lo_el_del TYPE REF TO if_wd_context_element.
DATA ls_del TYPE wd_this->Element_del.
DATA lo_nd_et_postab_1 TYPE REF TO if_wd_context_node.
DATA lo_el_et_postab_1 TYPE REF TO if_wd_context_element.
DATA ls_et_postab_1 TYPE wd_this->Element_del.
DATA lt_et_postab_1 TYPE wd_this->Elements_del.
DATA: wa_temp TYPE REF TO if_wd_context_element,
lt_temp TYPE wdr_context_element_set.
* navigate from <CONTEXT> to <ET_POSTAB_1> via lead selection
lo_nd_et_postab_1 = wd_context->path_get_node( path = `ZSHP_EXTENDED_DUE_LI.CHANGING_3.ET_POSTAB_1` ).
CALL METHOD lo_nd_et_postab_1->get_selected_elements
RECEIVING
set = lt_temp.
* navigate from <CONTEXT> to <DEL> via lead selection
lo_nd_et_postab_1 = wd_context->get_child_node( name = wd_this->wdctx_del ).
LOOP AT lt_temp INTO wa_temp.
CALL METHOD wa_temp->get_static_attributes
IMPORTING
static_attributes = ls_et_postab_1.
ls_et_postab_1-vbeln = del. // adding new attribute value.
APPEND ls_et_postab_1 TO lt_et_postab_1.
CLEAR ls_et_postab_1.
ENDLOOP.
lo_nd_et_postab_1->bind_table( new_items = lt_et_postab_1 ).

Problem : Recording video & audio from webcam

Hi all
I want to record myself to see the expression on my face on average through the USB webcam .
I use mencoder for recording from USB webcam .
mencoder tv:// -tv driver=v4l2:width=640:height=480:device=/dev/video0:forceaudio:adevice=/dev/dsp -ovc lavc -oac mp3lame -lameopts cbr:br=64:mode=3 -fps 16.2 -o test16.2.avi
The problem is that the audio is not synchronized with the video
what can i do ? help!
Last edited by remstereo (2010-11-17 08:16:45)

up

Problem recording from dec

Similar Messages

Maybe you are looking for