Problem reset Nexus 5596
Hello,
Some equipments Nexus 5596 from a customer have reinitiated and it seems to have been provoked by an OSPF problem although I am not sure.
The logs from the equipment show:
2013 Jan 9 07:29:42 ROISBPRE2CN %BTCM-5-BTCM_LOG_L3_READY: system becomes L3 Ready
2013 Jan 9 07:29:44 ROISBPRE2CN %VSHD-5-VSHD_SYSLOG_CONFIG_I: Configured from vty by on ppm.3726
2013 Jan 9 07:29:45 ROISBPRE2CN %OSPF-5-ADJCHANGE: ospf-1 [3236] Nbr 180.101.250.26 on Vlan902 went TWOWAY
2013 Jan 9 07:29:48 ROISBPRE2CN %OSPF-5-ADJCHANGE: ospf-1 [3236] Nbr 180.101.250.29 on Vlan902 went TWOWAY
2013 Jan 9 07:29:49 ROISBPRE2CN %OSPF-5-ADJCHANGE: ospf-1 [3236] Nbr 180.101.250.28 on Vlan902 went TWOWAY
2013 Jan 9 07:29:52 ROISBPRE2CN %OSPF-5-ADJCHANGE: ospf-1 [3236] Nbr 180.101.250.17 on Vlan902 went TWOWAY
2013 Jan 9 07:29:52 ROISBPRE2CN %OSPF-5-ADJCHANGE: ospf-1 [3236] Nbr 180.101.250.29 on Vlan902 went FULL
2013 Jan 9 07:29:52 ROISBPRE2CN %OSPF-5-ADJCHANGE: ospf-1 [3236] Nbr 180.101.250.26 on Vlan902 went FULL
2013 Jan 9 07:30:41 ROISBPRE2CN %ETHPORT-5-IF_DOWN_INITIALIZING: Interface port-channel902 is down (Initializing)
2013 Jan 9 07:30:41 ROISBPRE2CN %ETHPORT-5-IF_DOWN_INITIALIZING: Interface port-channel100 is down (Initializing)
2013 Jan 9 07:30:41 ROISBPRE2CN %ETHPORT-5-IF_DOWN_INITIALIZING: Interface Ethernet1/31 is down (Initializing)
2013 Jan 9 07:30:41 ROISBPRE2CN %ETHPORT-5-IF_DOWN_INITIALIZING: Interface Ethernet1/32 is down (Initializing)
2013 Jan 9 07:30:41 ROISBPRE2CN %ETHPORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_DOWN: Interface port-channel112 is down (No operational mem
bers)
2013 Jan 9 07:30:41 ROISBPRE2CN %ETHPORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_DOWN: Interface port-channel111 is down (No operational mem
bers)
I wanted to know if you know something about a problem with OSPF in next version:
cisco Nexus5596 Chassis ("O2 48X10GE/Modular Supervisor")
Intel(R) Xeon(R) CPU with 8263880 kB of memory.
bootflash: 2007040 kB
Kernel uptime is 0 day(s), 2 hour(s), 25 minute(s), 35 second(s)
System version: 5.1(3)N1(1a)
Thank you very much.
OSPF logs say that your switch is fully adjacent with 180.101.250.26 and .29, this means normal operation.
Bi-directional communication has been established between the Nexus and 180.101.250.17 and .28. They are in the middle of the OSPF neighboring process.
Some interfaces are initializing, and Po111 and 112 have no member ports (the channel-group <111|112> command hasn't been issued on any physical interfaces).
More information about OSPF neighbor states can be found here.
Similar Messages
-
Nexus 5596 switch-profile synchronization problem
hi
I can't synchronize switch-profile
System version: 5.1(3)N1(1)
Sync-status: Not yet merged
Merge Flags: pending_merge:0 rcv_merge:1 pending_validate:1
Status: Verify Failure
Error(s):
Following commands failed parsing: If the error is 'Command Parsing Failed', please check if some conditional feature(s) needs to be enabled
switchport mode trunk (Command Parsing Failed)
how to find the source of the problem ?Hello Pawel
Can you attach following from both Nexus 5596 switches in question
term length 0
show version
show run
show tech-support port-profile -
Nexus 5596 FC-Port Link-Events
Hi all,
int the last 3 weeks,
almost every day , we have a series of events in the connection between one Nexus 5596 and one of our servers. The connection is in FC (4G).
I need help to understand the output of the following command to troubleshoot what could be happening.
Sw-cpd-mm-n5k-2# show hardware internal fc-mac 3 port 14 link-event
MMDDYY HHMMSS usecs Event Current State
- - LINK_ACTIVE
100113 020845 773895 (0001) E_LINK_IDLE LINK_LRR_RX
100113 020845 765016 (0000) E_LINK_LRR LINK_LR_TX
100113 020845 763545 (61CB28) E_LINK_LINK_RESET LINK_ACTIVE
Sw-cpd-mm-n5k-2# show hardware internal fc-mac 3 port 14 port-event
MMDDYY HHMMSS usecs Event Current State
- - IPS_LINK_UP
100113 020845 775908 (0000) E_IPS_LINK_INIT_SUC IPS_LINK_UP
100113 020845 775907 (0000) E_IPS_IDLE IPS_LINK_UP
100113 020845 770040 (0001) E_IPS_LRR IPS_LINK_UP
100113 020845 763562 (61CB28) E_IPS_CREDIT_LOSS IPS_LINK_UP
Looking at the output I don't know who generates "E_LINK_LINK_RESET" , Nexus switch or server?
Thanks in advance!Hi,
I know it is a little bit late, but hope it can still be of use...
According to the log output, The switch detects a Credit Loss condition
00113 020845 763562 (61CB28) E_IPS_CREDIT_LOSS IPS_LINK_UP
and to recover from it, the switch resets the link by sending a LR to the server
100113 020845 763545 (61CB28) E_LINK_LINK_RESET LINK_ACTIVE
the server replies with a LRR, IDLE, etc.
100113 020845 765016 (0000) E_LINK_LRR LINK_LR_TX
Kind rgds,
Felipon -
VPC trouble - link flapping between C3750 stack and Nexus 5596
Hi All,
I have configured 1 vPC's between 2 Nexus 5596 and 1 stack C3750 switch. The links in the stack are distributed over both members.
Gi1/1/1 -> Eth 1/44 NX 5596-02
Gi 2/1/1 -> Eth 1/45 NX 5596-02
Gi 1/1/2 -> Eth 1/46 NX 5596-01
Gi 2/1/2 -> Eth 1/47 NX 5596-01
The same logic is for another stack C3750 to the same pair of Nexus 5596 switches.
The problem is that the links from the vPCs keep flapping at random moments - 1-2 times per hour.
The network is not loaded at this time and the same issue is on both vPC's.
the flaps in the nexus 5596 looks like this
%ETH_PORT_CHANNEL-5-PORT_DOWN: port-channel108: Ethernet1/44 is down
%ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel108: first operational port changed from Ethernet1/44 to Ethernet1/45
%ETHPORT-5-IF_DOWN_INITIALIZING: Interface Ethernet1/44 is down (Initializing)
%ETH_PORT_CHANNEL-5-PORT_UP: port-channel108: Ethernet1/44 is up
%ETHPORT-5-IF_UP: Interface Ethernet1/44 is up in mode trunk
On the stack is just up/down the pair interface.
I started few debugs on the stack and captured the folowing output:
C3750X-02#im_if_stack_relationship_add: Posting the ACP job for stack add for 5018.10902
im_if_stack_relationship_add: Posted the ACP job for stack add successfully
im_add_ifstackentry: higher_if_index = 5018 lower_if_index = 10902
im_add_ifstackentry: Failed to delete nolayerelem from NoLowerLayerTree for higher_ifIndex = 5018
im_add_ifstackentry: Failed to delete nolayerelem from NoHigherLayerTree for lower_ifIndex = 10902
im_add_ifstackentry: Deleted nolayerelems from NoHigherLayerTree and NoLowerLayerTree
im_add_ifstackentry: Failed to insert stackelem into StackTree
Jul 12 03:35:26.122: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/1/2, changed state to downim_if_stack_relationship_add: Posting the ACP job for stack add for 5018.10902
im_if_stack_relationship_add: Posted the ACP job for stack add successfully
im_add_ifstackentry: higher_if_index = 5018 lower_if_index = 10902
im_add_ifstackentry: Failed to delete nolayerelem from NoLowerLayerTree for higher_ifIndex = 5018
im_add_ifstackentry: Failed to delete nolayerelem from NoHigherLayerTree for lower_ifIndex = 10902
im_add_ifstackentry: Deleted nolayerelems from NoHigherLayerTree and NoLowerLayerTree
im_add_ifstackentry: Failed to insert stackelem into StackTree
Jul 12 03:35:29.058: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/1/2, changed state to up
Do someone have any idea what happens here ?
The configuration is ok because i have another vPC connected to FEX's and is working fine.
Kind regards,Hello,
Problem solved after upgrade to the last version of NX OS 6.0.2.N2.3
BR, -
I have a problem resetting my itunes account password
I have a problem resetting my itunes account password have loas the aswer to my secret password and my password to my email account, what to do? contact me at [email protected]
Click here and ask the iTunes Store staff to zero your account balance.
(115260) -
What is the best way to migrate zoning from an MDS9216i to a Nexus 5596?
I am migrating from a MDS9216i to a Nexus 5596. We have dual paths, so I can migrate one leg at a time and the full function for these switches is fiber channel attached storage.
What is the best way to migrate the zoning information? I have been told I can ISL the new and old switch together and then push the zoning to the new switch. Is that better than just cutting and pasting the zoning information to the new switch?
Also, I have to move four Brocade M4424 switches to the new switches - they are currently attached via interop mode 1, but will now be attached using NPIV. Has anyone done this before, and did you have any issues?
Any help or advice would be appreciated. Thanks!Use an ethernet cable to connect the two computers, and set up file sharing. After that copying files from one computer to the other is exactly like copying from one hard drive to another:
http://docs.info.apple.com/article.html?artnum=106658 -
Hello Friends,
Just want to save your precious time & effort, while doing Nexus 5596 upgrades so wanted to share some useful info which you can have a look prior to your upgrades of Cisco Nexus 5596 device.
I recently ran into trouble when upgarding one of datacenter switch Nexus 5596 does not boots up and after investigation from Cisco TAC it comes out to be Bug documented below.
https://tools.cisco.com/bugsearch/bug/CSCun66310/?reffering_site=dumpcr
My Upgrade path of device was : 5.1(3)N1(1) to 6.0(2)N2(5).
Since this upgarde involves upgrade of Bios and Power sequensor, I was having some doubts to get this succesfully upgraded, But there was more twist involved in this upgrade which I came to know after contacting Cisco TAC for my died Nexus 5596 device and got info that if you have below impacted version in your Nexus 5596 device and you are planning to do Upgrade, then you migh RUN into this serious BUG aftre which device won't come up at all and only Option left is to replace with RMA device.
PID Impacted Hardware versions Updated Versions
UCS-FI-6296UP 1.0 1.1
N5K-C5596UP 1.0 1.1
N5K-C5596T 1.1 1.2
You can check hardware version using below command from your device.
5596# show sprom sup | inc H/W
H/W Version : 1.1
So please be carefull when planning your Nexus 5596 upgrade and verify above things as this Bug is not present anywhere in Upgrade docuemntations unfortunately.
Hope this will help and save someone's precious Time.Today "upgraded" our switch (N5k-C5596UP) to from 5.1(2)N1 to 7.0(5) and after reboot no life from the switch either. Even no console response. show sprom sup | inc H/W shows 1:0.
Only thing we could do is RMA the switch. So what must I do with these switches? Have still to do 3 of them. -
Maximum number of interfaces in Port Channel on Nexus 5596
Let me preface this by saying I am not a network expert....
I noticed that our customer had configured a port channel on their Nexus 5596 comprised of 16 interfaces. I thought the maximum number of interfaces in a port channel was 8 interfaces? I see in the Nexus 7000 documentation that if you configure 16 interfaces, the remaining 8 will be in "hot standby." Is this the same behavior on the Nexus 5000 series?
Thank you.Same behavior on the 5500 series and other Cisco switches like 3750, 3850 , etc..
HTH -
Nexus 5596 Ethernet Port Configuration
I have a Cisco Nexus 5596 with 48 Ethernet Ports (two of which are now configured for Fibre Channel). It has a FEX attached to it as well.
I was able to configure ANY Ethernet port with the typical interface commands when in interface configuration mode. However, I can now only configure existing and new Port Channel interfaces, FEX ports and standard Ethernet ports that have never been configured before.
If I try to configure an Ethernet interface that was configured in the past, I only seem to have access to global interface commands when in interface configuration mode. I can set spanning-tree, duplex, speed or any other interface parameters. The CLI acts like I'm not in interface config mode, but the prompt shows that I am.
Anyone else seen such a thing? I am logged in as admin.Hi Mark
I suspect the interface in question is configured to be in a channel. Once an ethernet interface is configured to be in a port-channel. most interface commands need to be configured under the port-channel interface
Thanks
-Prashanth -
Question about Nexus 5596 log.
Dear Mister
When I connect toward Nexus 5596, using ipv4 telnet, send the next message:
NITE3# 2013 May 9 18:32:53 NITE3 %LOCAL7-4-SYSTEM_MSG: service telnet, IPV6_ADDRFORM - dcos-xinetd[3193]
What is the reason for this?
Could be a bug?
Best RegardsHi,
If you want to view the changes made to any an order than open that order and click on EXTRAS--> CHANGE DOCUMENTS in the main menu.
Also if u want to see the changes made it the status u can refer the table CRM_JCDS.
Regards,
PePe -
Nexus 5596 Licensing - filename exceeds 30 characters
Hi,
I'm trying to licensing two Nexus 5596 (Evaluated License), when i'm enter the "install license bootflash:LICENSE.lic" the Nexus reflect this error:
"Installing license failed: Invalid filename size, filename exceeds 30 characters".
After i changed the name the Nexus reflect this error:
"Installing license failed: Invalid/Corrupt license file"
I tried to clear the license from one switch and now i'm cannot reinstall the license.
In the mail that cisco sent to me with the license they wrote that do not change the filename.
Thanks in advance,
Nadav Katz.Hi Eric,
I received the Nexus switches with corrupted license.
The license team of cisco was generate a new license and send it to me.
Regareds,
Nadav. -
Nexus 5596 and QOS config guide
Hi,
I need to implement qos on a nexus device for a client
Basically what I am trying to implement is this but on the nexus
Policy Map Enhanced_QoS_Customer_Out
Description: Enhanced QoS customers outbound Percentages
Class Cust_VoIP_Out
priority 30 (%)
Class Cust_Gold_Out
bandwidth 30 (%)
Class Cust_Silver_Out
bandwidth 13 (%)
Class Cust_Bronze_Out
bandwidth 2 (%)
Policy Map Ethernet_QoS_Customer_Out_200Mb
Class class-default
Average Rate Traffic Shaping
cir 200000000 (bps)
service-policy Enhanced_QoS_Customer_Out
Is this possible on the nexus 5596?
I havent found much information around shaping.. Please advise if the above policy is achelievable on the nexus and if not what does the nexus support?
regards,Hi,
I don't think the 5500 support shaping since it is mostly a layer-2 device. Here is the config guide for QOS.
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/CLIConfigurationGuide/QoS.html
HTH -
Trunking nexus 5596 and netapp or exsi issue
hi
i have 2 issues with trunking between nexus 5596 and a esxi server .....can not get the servers to ping out
and the netapp connected to the same 5596 cannot ping.
if the server is a access port it works fine.
is there any tricks that are required to be configured on the nexus to make this work.Make sure we are actually tagging for those vlans on the host (Netapp/ESXi). If we are not, then this would explain why it works in access mode on the switch.
-
Lenovo U430: "There was a problem resetting your PC" error
I'm trying to install Windows 8.1 in my brother's new U430 touch. I created the recovery USB drive (formatted as FAT32). When I insert it and proceed with installation, it counts up to just a few percent of resetting and then says "There was a problem resetting your PC". It doesn't give me any information or choice other than to cancel the process.
How did you guys reinstall the OS after upgrading to an SSD? Did anyone else run into this problem?
Solved!
Go to Solution.When you say restore through OKR, you mean with the blank SSD installed, I should go to the recovery menu and refresh from there?
Answer: No. Partitions must exist and there should be some files in the hidden partitions for OKR to restore. So you must recreate the partitions for okr to work.
I don't have a way of clean installing the OS. That's the whole issue. I've put in SSDs in three other laptops in the past and each of them allowed me to create full recovery disks to reinstall a factory version of Windows on the new SSDs. I find it odd that Lenovo would choose to take that option away.
Answer: The factory copy of the OS is place in a hidden partition in the hdd. To restore or install it you have to run OKR through the Novo button if the OS does not exist. Options:
1. Recovery Dvd sets can be ordered from Lenovo. Just give them a call to inquire about it.
2. Make the USB OKR Recovery flash drive. This will recreate all the partiitons including the OS installer.
3. Clone the hdd using the included ssd cloning program or a third party program. You need to make a repair later to make the okr operational. -
We have a pair of Nexus 5596 switches, that each have a 1 gigabit conection to ISP CE switches (ME3400).
Switch 1 has a fibre connection using GLC-SX-MM with the following information...
sh int e1/48 trans
Ethernet1/48
transceiver is present
type is SFP-1000BASE-SX
name is CISCO-AVAGO
part number is SFBR-5766PZ-CS2
revision is
serial number is AGA1549L2BE
nominal bitrate is 1300 MBit/sec
cisco id is --
cisco extended id number is 4
I cannot get the port to come up on switch 2, transceiver info...
sh int e1/48 trans
Ethernet1/48
transceiver is present
type is SFP-1000BASE-SX
name is CISCO-AVAGO
part number is SFBR-5766PZ-CS2
revision is
serial number is AGA1549L2BE
nominal bitrate is 1300 MBit/sec
cisco id is --
cisco extended id number is 4
The port is up on the ISP switch, but down on the N5K...
Ethernet1/48 is down (Link not connected)
Hardware: 1000/10000 Ethernet, address: 547f.ee41.e337 (bia 547f.ee41.e337)
Description: Intech WAN ME3400-1 (BT)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 255/255, rxload 255/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 00:31:00
Last clearing of "show interface" counters 00:00:47
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 242.30 Gbps, 163.37 Mpps; output rate 63.30 Gbps, 231.54 Mpps
RX
17828772964 unicast packets 2506759 multicast packets 991 broadcast packets
17831280714 input packets 3305852407174 bytes
897530002 jumbo packets 0 storm suppression bytes
20 runts 0 giants 0 CRC 0 no buffer
20 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard Ethernet1/48 is down (Link not connected)
Hardware: 1000/10000 Ethernet, address: 547f.ee41.e337 (bia 547f.ee41.e337)
Description: Intech WAN ME3400-1 (BT)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 255/255, rxload 255/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 00:31:00
Last clearing of "show interface" counters 00:00:47
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 242.30 Gbps, 163.37 Mpps; output rate 63.30 Gbps, 231.54 Mpps
RX
17828772964 unicast packets 2506759 multicast packets 991 broadcast packets
17831280714 input packets 3305852407174 bytes
897530002 jumbo packets 0 storm suppression bytes
20 runts 0 giants 0 CRC 0 no buffer
20 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
I have tested the SFP's in use on a pair of 2960's & they work fine!
If i replace the SFP's for copper, then they work fine also.
Does anyone know of any incompatibility issue with this SFP?
Thanks
ColinDid you try a different port such as e1/1? Sounds like a bug to me
http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9670/data_sheet_c78-618603.html
Table 2.
Cisco Nexus 5500 Platform Transceiver Support Matrix
Maybe you are looking for
-
Hi, I do a lot of video and graphics on my Mac Pro 1,1 and would like to upgrade the CPU and graphics cards. I see the CPU may be a trickier install process, but it looks like I'll have no trouble changing out the graphics card. I'll probably just pa
-
Restore datafile from an OS copy
Hi all, I have a 10GR1 database open with datafiles marked as MISSING in the dictionnary. I have an OS copy oh those datafiles. These datafiles are contained in a Read Only tablespace. Could you explain me how can i recover this datafile to the datab
-
I installed Oracle 10 on aix Unix no issues - just want to create a db how?
why is it so hard to find out something so simple as creating a db using x-windows to my unix box from a laptop???
-
G4 OSX 10.2.8 freezing problems!!! please help!!
hello, two problems my friends.. 1. i have a G4 running OSX 10.2.8... recently my computer has begun to freeze all the time. about ten times a day... any ideas?? i'm not doing anything out of the ordinary.. it could freeze at any point, not just with
-
Surface Pro3 Logging Agent does not work
Hey Guys! I am developing mdm for surface pro3. I want to get the client mdmagent log for my mdm debugging. By following the steps mentioned in the section Agent Logging of Win8.1 Enterprise Device Management Protocol, I add the content which is "Ena