Problem setting comp to 133 fsb with MS-6390 \ bios flash problem

Ok you see when i under clock the computer to 100 fsb with a AMD 2400+ it will start by self and all is fine, but when i set it to 133 fsb(original speed) it need to restart cmos so that it will start again, also keeps poping up set date when i start windows so that might be battery but in just makeing sure. Also when i flash my bios after i says backup and i type y then it backs it up it will say directory not found or something, anyone got a solution, see if i dont need or need to flash bios and how to get it working?

naw dun got one (but got enough for it 30k =) getting it when i turn 16 =P ( curently 15 almost 16 in like 4 months but anyways back to the topic it is a top of the line power supply
MS-6390 KM266 Motherbaord
Radeon 9200 SE
Kbytes DDR PC 2700 333MHZ 256 MB ram stick
450 W Power Supply
Sound Blaster PCI Sound Card
AMD 2400+ Socket A
Maxtors 120 GB HD @ 7200 RPM
Model : Okia 420 ATX ( 420w Max)
Vac~Input |Voltage 115/230v| Voltage 10a/5a) | Frequency 60/50 hz
Max DC | +3.3 | +5 | +12| -12 | -5 | +5sb |Green | Grey |
OutPut | 28A | 40A| 18A|1.0A|3.0A| Com |P-On | PG

Similar Messages

  • Help with MS-6712 BIOS Flashing

    Hi
    Basically i got a new game for my PC (Halo) which wouldnt play properly even though my specs were all way above recommended. This is my specs
    Windows XP Home Edition SP1
    MS-6712 motherboard
    Athlon XP 2600+
    1024MB DDR PC 2700
    GeForce FX 5200 128MB
    160 Hard Drive
    Matshita DVD-RW
    On Board Sound and LAN card
    I read the Halo manual n it said to update my garphics, sound and BIOS drivers. I did the 1st two no problem. I wasnt to sure which BIOS update I would need so i got LiveUpdate 3 off the MSI site. I installed, downloaded the BIOS drivers automatically and installed the BIOS using a floppy disk and booting it. As far as i know the BIOS update was going fine untill it finished then I restarted my PC and there was nuthin, just a black screen. I rang up Time Computers (my manufacturer) and they helped me out. I then could boot my hard drive etc. BUT when i got to windows XP it said it needed activating, even though Time said that should never happen, and advised me to reboot using my Reload CD which I got with my PC.
    Tried that but an error comes up when the CD boots saying "unable to determine the BIOS lock".
    I installed Windows 98se which works fine now on a 2nd hard drigve (now set as master).
    I rang up time n they said the only thing I could do is get a new motherboard which is gonna cost me £120 (about $170). I would like to know if I could somehow get my original BIOS back, ive heard if clearing the CMOS but i dont no if that would solve anything or just make it worse than it is.
    Any replies would help and be REALLY appreciated
    Thanks.
    P.S after reading these forumns i had realised how stupid it was to update the BIOS even though my PC was runnin fine, I was just taking microsoft's word for it (anotha stupid thing) as they made Halo.

    the bloke at time is the only one will give you your original bios rom
    as they along with most oems use their own bios not the msi one
    and its some sort of id they put in it that the recovery disk is looking for,they are a conn,you paid for an os demand the proper disks
    they also use cheap power supplies so chances are you need a better one if you have added stuff to the box

  • Z68A-GD80 with SandyBridge 2600K with latest MSI Bios flashed dead?

    Dear Community
    I am desparate because I flashed my Z68A-GD80 G3 with the latest firmware 7672vJ2.zip from the MSI website. The update was fine and it completed 100%. However after the final reboot the screens stayed black and also the initial beeping for the usb ports was missing. The blue led was constant and the red led was blinking constantly. I opened my computer and did the JBAT1 reset but no luck. Then I tried to clear CMOS via the reset button on the backpanel. However no luck there as well. I did unplug the graphic card and the pci-e revodrive 3 and tried to boot in a minimal configuration. the screens stayed black.
    I don't know what else to try. At the moment I am super desperate and I am looking for help. Any hints are highly appreciated!

    The BIOS has failed. The only way to recover it is to enable the multi BIOS update. I am not sure if your board has a hard switch for a multi BIOS update or not. If not, then you obviously cannot enable it in the BIOS as you are unable to enter the BIOS. In that case the BIOS chip has to be reprogrammed via a SPI programmer or the board will have to be sent to MSI to get reflashed.
    There is an outside chance that fitting an Ivy CPU may just allow you to get into the BIOS, but I am not convinced as the flashing blue light normally indicates a failed BIOS.
    Remove the battery one more time and do another CMOS clear. Leave the battery out for around 30 mins. Then give it one more try.
    Hope you have a helpful PC shop in your area that may be able to assist with a SPI programmer if needed.

  • Why is that my pentium 2.66 only have a 133 fsb in the bios setting

    please educate me i cant figure out why is that in the bios core cell menu on my 915P Neo2 Platinum (1.0b) pentium 4 2.66 fsb 800 only displays a 133 fsb but i can see the processor runs correctly at 2667 with multiplier of 20. is this means the pentium 4 in the FSB category is only like a pentium3 with only a 133 fsb with a jacked up multiplier? 
    how to figure out the pentium 4's 800 FSB because i cant see it in the bios
    unlike an AMD with a 400 FSB have a 200 FSB in the bios because of DDR it doubles
    a true high speed FSB and in sync with the memory frequency is much better than just a large multiplier
    if my knowledge is wrong I apologize. pls help i really need to know 

    what default FSB should be displayed in the bios cell menu if my processor is a pentium 4 with a 800mhz FSB?
    but I really have a pentium 4 it says in the box it has a 800mhz FSB and the BIOS displays pentium 4 but it does'nt have HT. its an Intel 506 2.66G 1mb L2 cache LGA 775 pentium 4 processor none HT. its cheap thats why i bought it and upgrade later on
    can i lower the multiplier and increase the fsb to let say...400 and adjust the cpu ratio? it has a DDR2 memory at 533mhz is that right?
    i really don't have any sort of useful knowledge about this quad pumping scenes.... i mean processors going on in Intel Labs. sounds like an orgy to me....yeah pump that booty miss Northwood!
    I really don't have an idea how this pentium 4 works it been 3 yrs. since i've assembled a computer. technology moves so fast
    if your saying that i got a celeron D then that means i've got a fake pentium or a remarked? someone told me about this fake thing about processors in taiwan but its hard to believe that! imagine a processor built by a chinese   better get my lawyer then!

  • KT4V Problems with 133 FSB

    I've got a question about this board. The version I have is an OEM board, I have 1 major problem with it I have tried EVERYTHING i have read in the forums about it and nothing works. I can not get the board to run at the 133 FSB i have a AMD Tbird 1.33Ghz chip with the 266 FSB If i set my Bios to 130 FSB i can run at 1300 Mhz fine but when i go to 133FSB it just sits there and loops the Starting XP screen Here are my sys specs
    AMD 1.33 Tbird
    Thermaltake Valcano 7+ Running on the higest fan speed.
    MSI KT4V Mainboard
    PNY Geforce 4 Ti4200 8X Agp card
    600W Powersupply Robertron I believe
    1 60 Gig Maxtor HD
    1 60 Gig Samsung HD
    1 Aopen 20x CDRW Drive
    1 Stick of Kingston PC2100 256 DDR ram
    1 Stick of IBM PC2100 256 DDR ram
    I have tried it with each stick alone and each stick in different places everytime
    I am Running Windows XP Pro SP1 Installed and useing all the latest Drivers for the Vid, Built in Lan and Audio. Also the Latest Bios update 1.7 nothing seems to make this board run at 133FSB Any help would be greatly thanked.

    OK now I know its not my Heatsink or anything else on my system I know it is this board. I removed Everything execpt 1 hard drive put a old 4 meg PCI video card in and REmounted my HS and CPU and it took me 5 reboots just to get the board to post, after that i set it to the proper 133 FSB and got a NTDRL error changed it back to 100 FSB and it frooze 3 times before finally working After this experence I will Diffently NEVER buy a MSI board this board has been nothing but a headache from the start I will stick by my old faithful ABIT from this day foward..... Anyone wanna buy a slightly used MSI KT4V ??  :D

  • SSL-Problems when setting up a test environment with Exchange

    Hello everyone,
    I am trying to set up a test environment with Exchange 2013 to learn how the stuff works. However, I am facing some problems due to the fact that Exchange is designed for use with SSL certificates. The main thing that makes problems is the connection with
    RPC over HTTP. I've used the MS remote connectivity analyzer to find out why it is not working and as I thought it is because of a missing SSL certificate (it seems the self signed doesn't work here). Now in order to get this working I just bought a certificate
    for "mydomain.com". Now here is the first problem: This certificate is NOT a wildcard certificate. So if I understood correctly it works for mydomain.com but it won't work for subdomain.mydomain.com. Is this correct? (First question)
    If this is correct I will probably another problem: As I said this is a learning-environment so the server is at home behind a router. This means: Only one WAN-IP. I think could get this working by forwarding everything to the Exchange Server (like mydomain.com
    goes to the WAN-IP where the router is forwarding everything like port 25 or 443 directly to the exchange Server). This way I wouldn't have any problems I think: mydomain.com has a valid SSL cert, it resolves to my WAN-IP which forwards everything to the internal
    Exchange Server. Now here is the problem: I plan to setup a SharePoint Server as well. I thought about using ARR (IIS) to make both available behind the same WAN-IP without using ports inside the url. Ideally the Exchange Server should then be available via
    "mail.mydomain.com". This will work fine with ARR but then I probably have SSL problems again? (second question)
    Do you have any ideas what I can do to solve such problems? Should I buy another certificate for mail.mydomain.com? But then I would need to buy several certificates (e.g. for autodiscover.mydomain.com to get this working as well). This can become very expensive...
    Thanks!
    Regards
    Christian

    Hi,
    For your first question, if there is a single certificate just for “mydomain.com”, it cannot work for subdomain.mydomain.com.
    Generally, antodiscover.domain.com is used to access the autodiscover service for external users. If you just need test users to access Exchange server from internal environment, it is not necessary to get a certificate for autodiscover.domain.com.
    Therefore, for your second question what I can ensure is that if all URLs that used to connect Exchange from internal and external are configured to mail.mydomain.com with all services(IIS,SMTP,POP,IMAP), there will be no certificate problems in Exchange
    side.
    Best Regards,
    Winnie Liang
    TechNet Community Support

  • Can't reach 133 fsb

    I have been struggeling with this problem for a while. I´ve tried to replace my memory modules and I´ve also replaced my graficscard but it still didn't work.
    My system runs perfectly fine in 100 fsb but when I turn it up to 133 it just passes the ide-drivetest then it shuts down. The only thing I can think of is that the psu cant handle the load when it´s in 133 fsb.
    Note: I have been able to run the fsb at 133 earlier.I decided to upgrade my system on some weak spots and now it simply doesn´t work anymore.
    Here´s the list of changes:
    Added memory (512)
    Replaced GF mx460 with Ti 4200 (didn´t keep the mx)
    BIOS flash for faster cpu-support (haven´t bought new one yet since my old cpu doesn´t work properly).
    My question is therefor if it is possible that this small change could cause the powersupplie to cut?
    My second question is how much powerI need if I´d replace gpu and cpu with faster/better once, for an example GFFX 5600 Ultra and a AthlonXP 2400+ ?
    Third question: Where can I find a list of psu-manufactures that provide the correct figures? (There must be more than one).
    MSI KT3 Ultra-Aru
    Athlon XP2100+
    1x256 crucial pc2700
    1x512 crucial pc2700
    Asus GF4 Ti4200
    2xMaxtor Dimondplus9 80Gb Raid1
    Cheiftech 340W psu (standard psu)
    Thanks for your this great forum:)

    Tell about Amps. P.S. gives to 3.3v. 5v. and 12v. Try with only one memory module. You must have in mind that you are using Crucial memory and I have read toooo many posts of guys having problems on their PC and are also using Crucial mem.   8)

  • How to set up my elderly parent with Mac so that I can use remote access to help her?

    I want to set my elderly mother up with a new Mac mini so that I can use remote access to show her how use email, browse the internet, share photos.  (She lives in KY, I live in OR)
    She has had an iPhone and an iPad for about 6 months and she can barely use them without becoming frustrated.   I want to be able to see her screen with her and show her how to do things.
    My plan is to set her up with a Mac mini and I'll use my MacBookAir to remote into her system.  I'm buying the mini to configure and then I'll mail it to her.
    My question is whether to try to use Back to My Mac or Teamviewer for remote access
    I have broadband with comcast and she has broadband with Access Cable.  Each have their company modem/routers--neither of us have Airport Express.
    I have my own iCloud account and she has her own.   If I use Back to My Mac, it seems that I would need to set up a separate account on my Mac that would sync to her iCloud account.
    Teamviewer seems easier because I don't have to use a separate account.   Any advice?   Anything that I'm not thinking about?

    As Linc says, you can establish a Screen Sharing session via iMessage and Facetime.  The advantage of these 2 approaches is that once your Mom gets used to using them, she will be more comfortable using them to communicate with you.  I've talked to my Mom via iChat (aka iMessage) more since she learned to use them, then in all the years before that (including when I was a child ).  And just being able to see your Mom via Facetime can be useful when you want to gage how she is doing.
    However, if you are any distance from your Mom, they you want backup methods incase something goes wrong.
    So beside iMessage/Facetime, the next best would be Back-to-My-Mac via iCloud, however, you will want to establish her Mac as using your account so that you have the right to take control remotely.
    An alternative that does not mix up your iCloud acounts would be to use TeamViewer.com (which has an unattended mode so you can do off-hour maintenance when your Mom is not around; or check up on her to find out if she is dating - Turns out if I had been paying attention, I would not have been blind-sided by my Mom getting Married again last Summer - she is in her 80's! ).
    LogMeIn.com, as dwb says, can be used the same was as TeamViewer.com
    Both LogMeIn.com and TeamViewer.com are very good at making it easy to get through the home router and if you are having any problems connecting using other Methods, TeamViewer.com or LogMeIn.com will most likely not have any issues.
    Back-to-My-Mac allows screen sharing and file sharing so you can transfer files as well as control the screen.
    Screen Sharing via Messages allows cooperative file transfer. That is to say, you can try pushing a file to your Mom, but she has to accept each transfer.
    TeamViewer.com has an unattended file transfer mode.
    LogMeIn.com requires the paid version to transfer files.  However, there are other ways to transfer files, such as downloading them from the original source on your Mom's system while using screen sharing, using Dropbox (or similar), emailing them, etc...
    Of course if you are really network savvy, you can roll your own via ssh tunnels, port forwarding routers, getting dynamic DNS names, transferring files via scp, or tunneling AFP file sharing, tunneling your screen sharing sessions.  Lots of fun and excitement playing with terminal commands

  • TS4268 I can't activate FaceTime & iMessage on my iPad ... Would this have anything to do with already having these set up on my iPhone with the same apple ID?

    I can't activate FaceTime & iMessage on my iPad ... Would this have anything to do with already having these set up on my iPhone with the same apple ID?

    As long as you're logged into the same AppleID on both devices, this is not a problem.  It's only a problem if you're logged into a different AppleID and then try to associate FaceTime with an email that tied to the other AppleID.

  • I would like to set up an older iPad with a new messages account so it can be used by my kids.  I don't, however, want to lose the apps or music that are on the iPad. Can I change only the Messages "account"?

    I would like to set up an older iPad with a new messages account so it can be used by my kids.  I don't, however, want to lose the apps or music that are on the iPad. Can I change only the Messages "account"?

    Thanks. I had tried that, but was still having problems. Then I realized that I was using three addresses on both devices.  Once I changed it to only one email on one iPad and a different email on the other, it worked great. Your message encouraged me to dig deeper and think differently. It worked. Thanks again!

  • Can;t set up iCloud in Mail with Mavericks

    Hi,
    I am unable to set up icloud in mail.  II used migration assistant tto migrate from an older macbook pro running mavericks to a new one and for some reason there was an issue with iCloud Mail.  I then tried to add the account and despite no error messages, it fails to display in Mail.
    I am able to set up other accounts like Gmail and Exchange and they behave properly.  I have the latest version of Mail v7 (updated) and have successfully set up iCloud using a test account on my mac.  This means that the problem is user specific. I have tried removing mail dir in library and plists in preferences to set up mail again but with no luck.
    Does anyone have any ideas?
    Thanks

    Hello,
    I just got a Mac for a first time and I'm trying to configure Mail 3.5 with my gmail account and even after having followed all the steps seen on this forum, I just can't do it. The messages that come up are:
    "The IMAP server "imap.gmail.com" is not responding. Try checking the network connection, and that the server name is correct. Otherwise, the server might be temporarily unavailable. If you continue, you might not be able to receive messages"
    AND
    "The SMTP server "smtp.gmail.com" is not responding. Try checking the network connection, and that the server name is correct. Otherwise, the server might be temporarily unavailable. If you continue, you might not be able to send messages"
    it might be very basic but I can't manage. Can anyone help??
    Thanks in advance!!

  • I haven't set up my game center with my apple id so when i am trying to set it up and get to birth date part it starts all over how do i fix this?

    I haven't set up my game center with my apple id so when i am trying to set it up and get to birth date part it starts all over how do i fix this?

    If the problem persists, you'll probably have to make another apple id, it wont take off any games or music or apps or anything you've bought it will all stay there, i have two apple id's and i don't have a problem with anything.

  • Setting up a new office with Mac enviroment

    hey there,
    my orginization want to set up a new office witha Mac enviroment. currently we are working on microsoft desktops and servers hosted localy. so now im at a point where the desktops are not a problem, but the servers are, in addition to that i was asked to look into cloud hosted solutions for the servers .i have no idea what im doing since im a fresh graduate.
    i need to find out how the Mac enviroment works. Whats required from me in order to se up a succesfull mac enviroment enterprise?

    Start here:
    http://www.apple.com/business/mac/
    Then try to find a local business that already uses Macs and beg them to be shown around their setup.
    There's no real difference between using a Mac for home and using one for business except that you will need a bullet-proof network and it might be an idea to dedicate one machine to running OS X Server:
    http://www.apple.com/osx/server/
    depending on how big the business is.
    As for cloud hosting, there's no real difference between Macs and Windows for that: all the big providers provide both.  However, personally I do not trust and would not agree to work with a cloud service for a business yet.  You have no control over things and when it doesn't work you just sit there twiddling your thumbs.

  • Setting Up a New Studio with Logic Pro 9

    Hi Experts,
    I need your suggestion and help in setting up my Home Studio. I have the below hardware and would like to seek the suggestion of the experts in the forum to set this up.
    iMac 27 with 8GB DRAM & 1TB HDD - Corei5 2.8GHz
    Yamaha Motif XS8
    Korg Triton LE
    Roland Fantom G6
    Roland SP 20 Drum Pad
    Akai MPD 32 Drum Machine
    Logic Pro 9.1.4
    Reason 4
    Record 1.5
    Garritan Personal Symphony Orchestra
    Komplete 7
    East West Quantum Leap
    Focusrite Saffire Pro 40
    Roland Monitor Speakers
    I would like to use one of the Workstation (Yamaha Motif XS) as a Master Keyboard and use with Logic as the Master Sequencer. I would also like to use the Roland Fantom G6 and Korg Triton LE as MIDI and Audio Sources. Audio is not a problem as all of these are going straight into the Focusrite Saffire Pro 40. Now I have connected the Yamaha Motif XS 8 MIDI IN & OUT to Focusrite however I would like to complete the Architecture where in I can choose any Instrument from Logic / Reason / Yamaha / Motif / Korg and use the Logic as the Master Sequencer and use the Yamaha Motif to play these parts from the different sources.
    I would also like to know if I can use the Akai MPD 32 Drum Machine as a complete MIDI Controller.
    Any inputs are highly appreciated.
    Regards,
    CCIESRI

    I would strongly recommend reading the late great Pondini's article on Setup Assistant and Migration Assistant:
    http://pondini.org/OSX/SetupLion.html

  • TS3274 just bought ipad mini. As part of set up apple sent email with link  'Verify Now'. I've clicked it repeatedly but not responding. My email account is working fine. Any ideas?

    just bought ipad mini. As part of set up apple sent email with link  'Verify Now'. I've clicked it repeatedly but not responding. My email account is working fine. Any ideas?

    Why not just create an Apple ID for her and then you wont have any problems. Login on iMessage and Facetime using her ID and do the rest with your ID. It will work i tried it on my iPad

Maybe you are looking for