Problem setting data collection for SLD

Good day
I have the following situation.
A Solution Manager 71 installation, just recently patched to SP11. Previously I had the SLD on this system. And then a colleague informed that this could be a problem in the future as my ECC systems are Basis 731 which is higher level than the 702 on the Solution Manager system. So I installed a separate Java stack system on the same server as the Solution Manager.
The problem that I am faced with now is that I cant get the data collection (RZ70) to connect with the new Java system that I have installed. When I go into SLD and Administration, I see under Details>Data Suppliers that the server is specified as the Gateway Host, with a Gateway port of 3303. On the Solution Manager system it specified the gateway host as "localhost" and the gateway port as sapgw00.
So, from RZ70 I specify the gateway service as sapgw03 and then I get the result:
0: DSIMSID001_SID_00
: Collection of SLD data finished
0: DSIMSID001_SID_00
: Data collected successfully
0: DSIMSID001_SID_00
: RFC data prepared
0: DSIMSID001_SID_00
: Used RFC destination: SLD_NUC
0: DSIMSID001_SID_00
: RFC call failed: Error when opening an RFC connection (CPIC-CALL: 'ThSAPOCMINIT' : cmRc=17 thRc=2
0: DSIMSID001_SID_00
: Batch job not scheduled
And from the SLD_NUC entry in SM59 I get
Logon    Connection Error
Error Details    Error when opening an RFC connection (CPIC-CALL: 'ThSAPOCMINIT' : cmRc=17 thRc=2
Error Details    ERROR: SAP gateway communication error (Is SAP gateway closed?)
Error Details    LOCATION: SAP-Server DSIMSID001_SID_00 on host DSIMSID001 (wp 1)
Error Details    COMPONENT: CPIC
Error Details    COUNTER: 47
Error Details    MODULE:
Error Details    LINE:
Error Details    RETURN CODE: 239
Error Details    SUBRC: 0
Error Details    RELEASE: 721
Error Details    TIME: Mon Mar 16 14:04:05 2015
Error Details    VERSION:
Can anyone give me a few ideas what may be wrong here please?
Regards
Ray Phillips

Hi Ray,
Please check if the below SLD configuration is done.You can use any one of the two below link depending on how you want to configure your SLD.
Configure SLD for JCo and Creation of JCo Destinations - Portal - SCN Wiki
or
How to Create & Configure Local SLD on SAP NetWeaver 7.3 AS Java after Installation
If your SLD server is not a local SLD then make sure that in both the SLD system and the remote system host fine entry is there in /etc/hosts and etc/services.

Similar Messages

Firefox users cannot presently exercise choice, to opt-in or out of "data collected for improving services." As a result, Firefox is constantly dialing home, sometimes four times a day or more up to 48 times a day. There is some over-stepping and redunda

I understand the charter on this is to "check-in" once every time the program is turned on, and then once every 6 hours after that, or, once every 24 hours presumably. But the phone-home-effect is over-stepping these basic parameters. If a user turns their browser off and then on, Firefox is still obligated to "check-in" even if it just checked in 3 minutes prior. If the coding is not pre-designed to overstep, or act excessively in a redundant focus, the instance of once every six hours or once every 24 hours, is still overmuch if a user has been doing this (non-voluntarily-participating) for 9 months or longer.
== This happened ==
Every time Firefox opened
== This started when Firefox took up the initiative of "improving service. to end users" or similar idea, making the web safer for novice users, etcetera.

Opening question was truncated. Should read: "Firefox users cannot presently exercise choice, to opt-in or out of "data collected for improving services." As a result, Firefox is constantly dialing home, sometimes four times a day or more up to 48 times a day. There is some over-stepping and redundancy here. It would seem the practice of "improving service" has been accomplished with as much information as Mozilla has gathered in the last 6-18 months about its users habits. '''Isnt it about time to give users the option to opt out of that now that most the heavy liftiing has been accomplished?'''"

T5SSCXSSSERVICES - Set Data Tracking for Individual Self-Services

Hi,
We have a requirement for BI Report to fetch data from table :T5SSCXSSSERVICES
The above table could be filled with data when we perform any activities in ESS and MSS.
I wanted to know what are all required configuration to get data in to the table T5SSCXSSSERVICES
I understand below mentioned configuration are required:
IMG Node 1: Activate Data Tracking for All Self-Services
IMG Node2: Set Data Tracking for Individual Self-Services
Is it required to activate Business FunctionS et - HR Administartive Servcices?
Guide me with more inputs,
Regards
Ramanathan

Hi Ramanathan,
I am facing the same doubt now, are you able to share your experience on how to populate T5SSCXSSSERVICES ? Appreciate that, and thank you in advance.
Regards
Kir Chern

Problem setting up data collection for a performance problem

We have a performance problem on our production environment: there is a query that is long to display specially on specific records involving a lot of détails. I had the idea to set up data collection to investigate the problem.
I used the wizard to set up data collection with default settings.
I had created a database PERF_DW on our test server for that purpose.
I didn't have any problem with the wizard: it created data collection sets and SQL Server agents tasks and probably many objects. But I don't know where I missed something but I didnt, have the chance to specify the database I wanted to tune
and even when I started data collection, I couldn't figure out where were the reports.
Then I tought that I did it all wrong so I stopped data collection and dropped the database and tried to deleted the jobs created and I had the following message:
TITRE : Microsoft SQL Server Management Studio
Échec de Supprimer pour Travail « collection_set_1_noncached_collect_and_upload ». (Microsoft.SqlServer.Smo)
Pour obtenir de l'aide, cliquez sur :
http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&ProdVer=11.0.2100.60+((SQL11_RTM).120210-1917+)&EvtSrc=Microsoft.SqlServer.Management.Smo.ExceptionTemplates.FailedOperationExceptionText&EvtID=Supprimer+Job&LinkId=20476
INFORMATIONS SUPPLÉMENTAIRES :
Une exception s'est produite lors de l'exécution d'une instruction ou d'un lot Transact-SQL. (Microsoft.SqlServer.ConnectionInfo)
The DELETE statement conflicted with the REFERENCE constraint "FK_syscollector_collection_sets_collection_sysjobs". The conflict occurred in database "msdb", table "dbo.syscollector_collection_sets_internal", column 'collection_job_id'.
The statement has been terminated. (Microsoft SQL Server, Erreur : 547)
Pour obtenir de l'aide, cliquez sur :
http://go.microsoft.com/fwlink?ProdName=Microsoft%20SQL%20Server&ProdVer=11.00.3128&EvtSrc=MSSQLServer&EvtID=547&LinkId=20476
BOUTONS :
OK
Now I understand that the collectors prevent the jobs from being deleted but I can't delete the collectors.
What should I do?
Any help is appreciated.
Thank you for your advice.
Sylvie P

Hello,
Please refer to the following article.
http://blogs.msdn.com/b/sqlagent/archive/2011/07/22/remove-associated-data-collector-jobs.aspx
You can run the dcclenaup.sql script mentioned in the article.
Another option is using sp_syscollector_cleanup_collector.
http://blogs.msdn.com/b/sqlagent/archive/2012/04/05/remove-associated-data-collector-jobs-in-sql-2012.aspx
Hope this helps.
Regards,
Alberto Morillo
SQLCoffee.com

Problem Topology Data collection LMS 4.1

Hi there,
I have an issue with the lms 4.1 Topology Data Collection. In the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary, there are only 2 devices succeeded and 0 device fail. but I have more 500 device in state managed. I run Inventory Collections but the number doesn't change.
Inventory Collection          534                13 02 May 2012, 11:07 CEST Idle          Schedule
Config Archive                         507               14 02 May 2012, 09:51 CEST Running          Schedule
Topology Data Collection               2               0 02 May 2012, 11:11 CEST Idle          Schedule
I have read others discussions but no one has the same problem or similar problem. The only possible solution is to reset the ANI db but I'm not sure if it it's the best solution.
Any ideas?
Thaks for help

I confirm that Martin. Good spotting!. I just noticed it in a server I installed yesterday. These 2 lines were added to the hosts file.
127.0.0.1       localhost
127.0.0.1   LMS4
A bit silly for both, since these entries were allready in the hosts file, done by the windows install I think
127.0.0.1       localhost
::1             localhost
Cheers,
Michel

Problem in data sources for transaction data through flat file

Hello Friends,
While creating the data sources for transaction data through flat file, I am getting the following error "Error 'The argument '1519,05' cannot be interpreted as anumber' while assigning character to application structure" Message no. RSDS016
If any one come across this issue, please provide me the solution.
Thanks in Advance.
Regards
Ravi

Hallo,
just for information.
I had the same problem.
Have changed the field type from CURR to DEC and have set external instead of internal.
Then, the import with flatfile worked fine.
Thank you.

Setting date format for the entire SQL Server installation - SQL Server 2008 R2-2012

Hi,
I need to safeguard the behaviour of SQL codes that inserting into SQL tables with some date columns. For this purpose, I need to change the date format for the SQL instance and not using CONVERT and CAST.
I've seen the SET DATE FORMAT statement, but if I use it, could I solve my problem?
Thanks

The language setting is related to the database user.
BOL: "DEFAULT_LANGUAGE = { NONE | <lcid> | <language name> | <language alias> }
Specifies the default language for the new user. If a default language is specified for the user and the default language of the database is later changed, the users default language remains as specified.
If no default language is specified, the default language for the user will be the default language of the database. If the default language for the user is not specified and the default language of the database is later changed, the default
language of the user will change to the new default language for the database."
LINK: http://technet.microsoft.com/en-us/library/ms173463.aspx
The default language setting can be overridden by SET LANGUAGE for the session:
http://technet.microsoft.com/en-us/library/ms174398.aspx
Example:
SET LANGUAGE us_english; -- mdy
SELECT CAST ('12/13/2014' as DATE); -- 2014-12-13
GO
SET LANGUAGE british; -- dmy
SELECT CAST ('12/13/2014' as DATE);
GO
(1 row(s) affected)
Changed language setting to British.
Msg 241, Level 16, State 1, Line 2
Conversion failed when converting date and/or time from character string.
Kalman Toth Database & OLAP Architect
SELECT Video Tutorials 4 Hours
New Book / Kindle: Exam 70-461 Bootcamp: Querying Microsoft SQL Server 2012

Problems with Data collection in CM 5.0.6

Hello:
I have installed LMS 3.0.1 and CM 5.0.6, and I have some problems with CM:
-Although data collection is scheduled, this does not run.
I try to launch it from CM menu, it asks if I want the collection of all devices or the new ones.
I try the two options but it does not do anything.
-I can launch the UT acquisition but it does not collect all the hosts.
I compare the configuration of the devices that "works" and the others and dont see no difference.
-The UT acquisition does not discover our Ip phones.
-In data collection settings there are 5 devices that are included but not managed.
-When I restart the server the data collection works fine, but the next day it doesn't work.
Thanks!!!

Hi,
As suspected, Campus Manager 5.0.6 hitting a bug as found the following exception in ani.log :-
2011/03/14 15:05:40 Discovery ani ERROR AniTimeLine: TimeBase Discovery caught exception: java.lang.NullPointerException
java.lang.NullPointerException
    at com.objectspace.jgl.HashMap.put(HashMap.java)
    at com.cisco.nm.ani.server.core.PortDetailsXml.populatePortData(PortDetailsXml.java:109)
    at com.cisco.nm.ani.server.core.DiscoveryTimeBaseImpl.generatePortDetailsXml(DiscoveryTimeBaseImpl.java:104)
    at com.cisco.nm.ani.server.core.DiscoveryTimeBaseImpl.postPerformScheduledFunction(DiscoveryTimeBaseImpl.java:81)
    at com.cisco.nm.ani.server.frontend.AniTimeBaseImpl.execute(AniTimeBaseImpl.java:48)
    at com.cisco.nm.ani.server.frontend.AniTimeLine.executeTimeBase(AniTimeLine.java:317)
    at com.cisco.nm.ani.server.frontend.AniTimeLine.runSchedule(AniTimeLine.java:350)
    at com.cisco.nm.ani.server.frontend.AniTimeLine.run(AniTimeLine.java:366)
    at java.lang.Thread.run(Thread.java:595)
BUG ID = CSCtd49439
link to view bug at Cisco.com
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtd49439
You need to contact TAC for the patch.Kindly click on Action --> open Service Request and it will put all these notes and logs of this thread to the TAC case.
Once the data collection issue will be fixed and the correct number of devices being data collected properly, then you need to make sure to add "Call Manager" to Common Services with the community string credentials and run the data collection and UT Acquisitions to get the IP Phones discovered.
Thanks,
Gaganjeet

Meet a problem of data exchange for sale order from CRM to R3.

Dear Friends:
      I do the data exchange for sale oder from to R3 today , the problem's detail is as follows:
      When i save a sale order in CRM (Version is 5.0) . it can automatically generate a bdoc which bdoc type is BUS_TRANS_MSG. but the bdoc status alway is "Sent to receivers (not all have confirmed)". and the original order in CRM can not be change .it quote that "Document is being distributed - changes are not possible", so i check the order status analysis in detail .it presents two error messages ," Event 'BEFORE_CHANGE', attribute '     FINI': Error code for function module 'CRM_STATUS_BEFORE_COMPLETED_EC' , "Item is not yet completed in OLTP system". so i check the order in R/3 ,it has already been create and without any error messages.
   Would like to tell me how to solve it . thanks your any idear..

Hi Benjamin,
When performing uploads to R/3 from CRM there is a response from the OTLP system that is sent back to the CRM Middleware to confirm that the data records were received and processed correctly.
Here is a checklist you can run through to verfiy that the connections, systems and objects that are needed are all in place:
<b>On R/3 system:</b>
- Check R/3 outbound queue (transaction SMQ1) for any entries that are not reaching CRM.
- Check that all RFC destinations on R/3 are defined correctly and are pointing to CRM
- Check the CRMCONSUM table in R/3 to ensure CRM is registered as a consumer
- Check the CRMRFCPAR table in R/3 to ensure that order objects are valid for exchange between R/3 and CRM
- Check for any short dumps in R/3 (ST22/ST21)
<b>On CRM:</b>
- Are there entries stuck in the inbound queue (SMQ2) with R3AU* names?
- What does the CRM Middleware Trace show (SMWT)? Sometimes this has more detail than the specific BDoc overview (SMW01)
- Check for short dums in CRM (ST22)
Let us know what else you uncover and we can work from there.
Brad

IDOC: Problem with data filter for IDOC extension field

Hallo!
I've created an idoc extension for the basic type DEBMAS06 that works fine. Now I want to use a data filter for one field ( company code ) of my segment. Every segment with a company code different from 100 should be filtered and not send to the other client. But what happend is that for all customers that have at least one company code different from 100, all segments including the one with cc 100 were deleted and a error "Segment ... does not exist for message type DEBMAS" appeared on the screen.
Does anyone have any ideas about this problem?

Not sure about changes to be made at the filtering options.
An alternative would be sending the data to XI as it is and perform the mapping to remove the unnecessary segments.
Disadvantage: Unnecessary processing of segment would be done at XI.
Advantage: The integration logic would be completely handled by XI.
Regards,
Prateek

How to do filter data after Data Collection for Oracle PS

Hi Experts,
I have a critical issue on the "Data Volume" after data collection program.
If I give this big chunk of data as a input to PS, then integration program is not taking this High volume of data into PS.
Hence now I have a critical task to reduce number of Data.
In this front, first I need to delete some items which are not required for PS in the base table(In MSC_SYSTEM_ITEMS) after collection program, but I do not know the dependent entities which also has to be taken care in MSC side after collection, If I delete the itrems from MSC_SYSTEM_ITEMS..
Hence I require help on this data filter issue.
Appreciating anyone's help in advance...
Thanks & Regards,
Bharathram N

Hello,
Have you looked at the request Purge ODS Data of Collections? Using this you can delete all the collected data for a specific instance id.
Once that is done you can run a complete refresh for all entities for all enabled organizations. This will ensure that old data pertaining to disabled orgs is removed.
Additionally in 11.5.10 (collections rup 32 and later) there is a feature implemented which does not pull data from disabled organizations into the source snapshots. This in itself does not make a difference for the ODS data, but does give better performance in the refresh snapshots.
One thing to take into account if your purge the ODS data that in the event when you still have ascp plans that are based on this data, then you may end up with no data being displayed in the workbench (because the lid tables have been purged). Here you would have to rerun the plans.
best regards
Geert

Problems setting Data Scope

Hello.
I'm working with B1iSN B12B1 integration and I'm having troubles with the Data Scope. I'm following the operation guide for this kind of integration, but somehow in the Bizstep selection area when I choose any other bizstep besides Z.B1PO2B1SO, the only one available into the Data Scope area is Z.B1PO2B1SO.
I think this is not supposed to happen, but I'm not sure. Am I doing anything wrong? What Can I do to change this.
Thanks.
Regards, Marta

Hi Marta,
No worry. There is nothing wrong. In the B12B1 package, I set vendor filteration for B1PO2B1SO only, so only B1PO2B1SO is listed in DataScope. Any way, B12B1 bizpackage is just for your reference, you can extend it according to your requirement.
Congratulation! You're almost there.
Any feedback about the bizpackage and guide is welcome. Thanks.
Kind Regards, Yatsea

Problem setting maximum characters for a date field.

Good morning all. I am trying to ensure that a date field on the form I am working on validates if the entry is not more than 8 digits, and if it is more, it should display a message, and return the focus back to the field until it is correct. Below is the code I wrote but it is not working:
if(DATE1.length>"8"){
    xfa.host.messageBox(Enter eight digits for the date in the format YYYYMMDD or use the drop down calendar.);
xfa.host.setFocus("form1.Page1.DATE1");
I do not know why it is not working, i need help. I have this code on the exit event.
Thanks
v/r
Tammy

Well you are missing the " around the text in your messagebox but even then it doesn't seem to work. I am not a javascript expert so am not sure why but it works in formcalc like this:
if(Len($) > 8) then
    xfa.host.messageBox("Enter eight digits for the date in the format YYYYMMDD or use the drop down calendar.")
    xfa.host.setFocus("$")
endif

Problems setting up iReport for SLM development

Hi!
I've been trying to set up Eclipse and iReport so that I can create
some custom reports for SLM, but this has proven difficult. I'll explain
what I've done and where it fails:
1) I've followed all instructions on this page:
'Sentinel Development Environment'
(http://www.novell.com/developer/sent...vironment.html)
I get the following error in step 4 in the section entitled
"Enabling Previewing
Reports That Query The Sentinel Log Manager Event Store"
Exception in thread "main" 05.jan.2011 14:37:12
esecurity.base.error.SentinelErrorCodes <clinit>
INFO: There are 71 defined error codes.
esecurity.base.exceptions.RemoteException:
at
esecurity.db.object.IndexedLogSearchServiceRemoteI mpl.startSearch(Ind
exedLogSearchServiceRemoteImpl.java:54)
at
com.novell.reports.jasper.data.event.EventDataSour ce.nextEvent(EventD
ataSource.java:156)
at
com.novell.reports.jasper.data.event.EventDataSour ce.next(EventDataSo
urce.java:145)
at
com.novell.reports.jasper.data.event.ConnectionChe ck.main(ConnectionC
heck.java:66)
Caused by: esecurity.base.exceptions.RemoteException:
at
esecurity.base.datamodel.method.MethodResult.setEx ception(MethodResul
t.java:55)
at
esecurity.base.ccs.comp.BaseRemoteObjectTask.execu te(BaseRemoteObject
Task.java:120)
at
esecurity.base.ccs.comp.GenericRemoteObjectTask.pr ocessRequest(Generi
cRemoteObjectTask.java:86)
at
esecurity.base.ccs.comp.GenericTask.process(Generi cTask.java:91)
at
esecurity.base.ccs.comp.GenericTask.process(Generi cTask.java:65)
at esecurity.base.ccs.comp.BaseTask.run(BaseTask.java :52)
at
esecurity.base.ccs.comp.threadpool.TaskThreadPool$ RunWrapper.run(Task
ThreadPool.java:89)
at
EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Wo rker.run(PooledExec
utor.java:732)
at java.lang.Thread.run(Thread.java:619)
Caused by: java.lang.reflect.InvocationTargetException
at sun.reflect.NativeMethodAccessorImpl.invoke0(Nativ e Method)
at
sun.reflect.NativeMethodAccessorImpl.invoke(Native MethodAccessorImpl.
java:39)
at
sun.reflect.DelegatingMethodAccessorImpl.invoke(De legatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at
esecurity.base.ccs.comp.BaseRemoteObjectTask.execu te(BaseRemoteObject
Task.java:113)
... 7 more
Caused by: java.lang.RuntimeException: No param auditInfo for method id
= _start
Search_,name = startSearch
param=startTime, type=java.util.Date, value=nullparam=limit, type=long,
value=1p
aram=sortFields, type=java.util.List, value=nullparam=searchString,
type=String,
value=sev:[9 TO 9] MAXCOUNT=1param=pageSize, type=integer,
value=10000param=end
Time, type=java.util.Date, value=nullparam=user, type=String,
value=admin
at
esecurity.base.datamodel.method.ObjMethod.getParam (ObjMethod.java:250
at
esecurity.base.datamodel.method.ObjMethod.getDataO bjectValue(ObjMetho
d.java:107)
at
esecurity.db.object.IndexedLogSearchServiceServerS tub._startSearch_(I
ndexedLogSearchServiceServerStub.java:66)
... 12 more
I noticed another thread on this error, but as you can see from the
configuration.xml file I am using the system user so rights shouldn't be
the cause here:
<strategy active="yes" id="sentinel_client"
location="com.esecurity.common.communication.strat egy.jmsstrategy.activemq.ActiveMQStrategyFactory"
name="ActiveMQ">
<jms
brokerURL="ssl://x.x.x.x:61616??wireFormat.maxInactivityDuration=0"
interceptors="compression"
keystore="C:\\Users\\ragsto\\Development\\Sentinel
SDK\\content\\dev\\sdk\\build\\config\\.activemqcl ientkeystore.jks"
keystorePassword="password" password="832f515a51412dec5ec22dfa756693ab"
username="system"/>
</strategy>
I decided test the reports even with this error, but whenever I open a
TemplateReport.jrxml I immediately get the following error:
net.sf.jasperreports.engine.JRRuntimeException:
net.sf.jasperreports.engine.JRException: Class
com.novell.reports.jasper.data.event.LuceneEventQu eryExecutorFactory not
found.
In the DOS window where I started iReport from, I get the following
error:
Can't find the translation for key =
gui.elementpropertiessheet.sheetProperty.re
nderType: using default (Render type)
Can't find the translation for key =
gui.elementpropertiessheet.sheetProperty.re
nderType: using default (Render type)
End event threw exception
java.lang.reflect.InvocationTargetException
at sun.reflect.NativeMethodAccessorImpl.invoke0(Nativ e Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(Unknow n Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(Un known
Source)
at java.lang.reflect.Method.invoke(Unknown Source)
at
org.apache.commons.beanutils.MethodUtils.invokeMet hod(MethodUtils.jav
a:216)
at
org.apache.commons.digester.SetNextRule.end(SetNex tRule.java:216)
at org.apache.commons.digester.Rule.end(Rule.java:230 )
at
org.apache.commons.digester.Digester.endElement(Di gester.java:1130)
at
it.businesslogic.ireport.compiler.xml.SourceTraceD igester.endElement(
SourceTraceDigester.java:159)
at
org.apache.xerces.parsers.AbstractSAXParser.endEle ment(Unknown Source
at
org.apache.xerces.impl.dtd.XMLDTDValidator.endName spaceScope(Unknown
Source)
at
org.apache.xerces.impl.dtd.XMLDTDValidator.handleE ndElement(Unknown S
ource)
at
org.apache.xerces.impl.dtd.XMLDTDValidator.endElem ent(Unknown Source)
at
org.apache.xerces.impl.XMLDocumentFragmentScannerI mpl.scanEndElement(
Unknown Source)
at
org.apache.xerces.impl.XMLDocumentFragmentScannerI mpl$FragmentContent
Dispatcher.dispatch(Unknown Source)
at
org.apache.xerces.impl.XMLDocumentFragmentScannerI mpl.scanDocument(Un
known Source)
at org.apache.xerces.parsers.XML11Configuration.parse (Unknown
Source)
at org.apache.xerces.parsers.XML11Configuration.parse (Unknown
Source)
at org.apache.xerces.parsers.XMLParser.parse(Unknown Source)
at org.apache.xerces.parsers.AbstractSAXParser.parse( Unknown
Source)
at
org.apache.xerces.jaxp.SAXParserImpl$JAXPSAXParser .parse(Unknown Sour
ce)
at
org.apache.commons.digester.Digester.parse(Digeste r.java:1647)
at
net.sf.jasperreports.engine.xml.JRXmlLoader.loadXM L(JRXmlLoader.java:
239)
at
net.sf.jasperreports.engine.xml.JRXmlLoader.loadXM L(JRXmlLoader.java:
226)
at
it.businesslogic.ireport.IReportCompiler.loadJaspe rDesign(IReportComp
iler.java:2125)
at
it.businesslogic.ireport.DesignVerifyerThread.veri fyDesign(DesignVeri
fyerThread.java:145)
at
it.businesslogic.ireport.DesignVerifyerThread.run( DesignVerifyerThrea
d.java:92)
at java.lang.Thread.run(Unknown Source)
Caused by: net.sf.jasperreports.engine.JRRuntimeException:
net.sf.jasperreports.
engine.JRException: Class
com.novell.reports.jasper.data.event.LuceneEventQu eryE
xecutorFactory not found.
at
net.sf.jasperreports.engine.design.JRDesignDataset .queryLanguageChang
ed(JRDesignDataset.java:914)
at
net.sf.jasperreports.engine.design.JRDesignDataset .setQuery(JRDesignD
ataset.java:448)
at
net.sf.jasperreports.engine.design.JasperDesign.se tQuery(JasperDesign
.java:806)
... 28 more
Caused by: net.sf.jasperreports.engine.JRException: Class
com.novell.reports.jas
per.data.event.LuceneEventQueryExecutorFactory not found.
at
net.sf.jasperreports.engine.util.JRSingletonCache. createInstance(JRSi
ngletonCache.java:98)
at
net.sf.jasperreports.engine.util.JRSingletonCache. getCachedInstance(J
RSingletonCache.java:78)
at
net.sf.jasperreports.engine.util.JRQueryExecuterUt ils.getQueryExecute
rFactory(JRQueryExecuterUtils.java:60)
at
net.sf.jasperreports.engine.design.JRDesignDataset .queryLanguageChang
ed(JRDesignDataset.java:903)
... 30 more
Caused by: java.lang.ClassNotFoundException:
com.novell.reports.jasper.data.even
t.LuceneEventQueryExecutorFactory
at java.net.URLClassLoader$1.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
at java.net.URLClassLoader.findClass(Unknown Source)
at java.lang.ClassLoader.loadClass(Unknown Source)
at sun.misc.Launcher$AppClassLoader.loadClass(Unknown Source)
at java.lang.ClassLoader.loadClass(Unknown Source)
at java.lang.Class.forName0(Native Method)
at java.lang.Class.forName(Unknown Source)
at
net.sf.jasperreports.engine.util.JRClassLoader.loa dClassForRealName(J
RClassLoader.java:179)
at
net.sf.jasperreports.engine.util.JRClassLoader.loa dClassForName(JRCla
ssLoader.java:119)
at
net.sf.jasperreports.engine.util.JRSingletonCache. createInstance(JRSi
ngletonCache.java:88)
... 33 more
locationFileName does not exisit
It looks to me like there's a problem with the Lucene connection, but
the connection test works..?
When I try to compile the report, I get the following errors:
The method DatePrepare(String, String, String) is undefined for the
type TemplateReportScriptlet
The method DatePrepare(String, String, String) is undefined for the
type TemplateReportScriptlet
The method getKeyColors() is undefined for the type
TemplateReportScriptlet
The method getKeyColors() is undefined for the type
TemplateReportScriptlet
The method DatePrepare(String, String, String) is undefined for the
type TemplateReportScriptlet
This is similar to another users error, but I wasn't able to solve my
problem by compiling in iReport 3.7.6 - I just get different errors.
Since I am not very familiar with Java, I have no idea on how to
troubleshoot this. Can anyone assist, please?
Ragnar Storstrm
rstorstrom
rstorstrom's Profile: http://forums.novell.com/member.php?userid=5064
View this thread: http://forums.novell.com/showthread.php?t=429304

That fixed the problem with the connection check - thank you! But I
still have two problems left:
1) When I create a new report in Eclipse and try to compile it in
iReport I get the following error:
Compiling to file... C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\TemplateReport.jasper ->
C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\TemplateReport.java
net.sf.jasperreports.engine.design.J...va.lang.ClassNotFoundException:*TemplateReportClass
Line:*21,*Column:*36*JRXML*Element:*/jasperReport
Exception*in*thread*"AWT-EventQueue-0"*java.lang.ArrayIndexOutOfBoundsException:*2*>=* 2
****at*java.util.Vector.elementAt(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI.ge tTextViewForTab(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI.ca lculateTabHeight(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI.ca lculateMaxTabHeight(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI$Ta bbedPaneLayout.calculateTabRects(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI$Ta bbedPaneLayout.calculateLayoutInfo(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI$Ta bbedPaneLayout.layoutContainer(Unknown*Source)
****at*java.awt.Container.layout(Unknown*Source)
****at*java.awt.Container.doLayout(Unknown*Source)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validate(Unknown*Source)
****at*javax.swing.RepaintManager.validateInvalidC omponents(Unknown*Source)
****at*javax.swing.SystemEventQueueUtilities$Compo nentWorkRequest.run(Unknown*Source)
****at*java.awt.event.InvocationEvent.dispatch(Unk nown*Source)
****at*java.awt.EventQueue.dispatchEvent(Unknown*S ource)
****at*java.awt.EventDispatchThread.pumpOneEventFo rFilters(Unknown*Source)
****at*java.awt.EventDispatchThread.pumpEventsForF ilter(Unknown*Source)
****at*java.awt.EventDispatchThread.pumpEventsForH ierarchy(Unknown*Source)
****at*java.awt.EventDispatchThread.pumpEvents(Unk nown*Source)
****at*java.awt.EventDispatchThread.pumpEvents(Unk nown*Source)
****at*java.awt.EventDispatchThread.run(Unknown*So urce)
Exception*in*thread*"AWT-EventQueue-0"*java.lang.ArrayIndexOutOfBoundsException:*2*>=* 2
****at*java.util.Vector.elementAt(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI.ge tTextViewForTab(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI.ca lculateTabHeight(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI.ca lculateMaxTabHeight(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI$Ta bbedPaneLayout.calculateTabRects(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI$Ta bbedPaneLayout.calculateLayoutInfo(Unknown*Source)
****at*javax.swing.plaf.basic.BasicTabbedPaneUI$Ta bbedPaneLayout.layoutContainer(Unknown*Source)
****at*java.awt.Container.layout(Unknown*Source)
****at*java.awt.Container.doLayout(Unknown*Source)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validateTree(Unknown*Sou rce)
****at*java.awt.Container.validate(Unknown*Source)
****at*javax.swing.RepaintManager.validateInvalidC omponents(Unknown*Source)
****at*javax.swing.SystemEventQueueUtilities$Compo nentWorkRequest.run(Unknown*Source)
****at*java.awt.event.InvocationEvent.dispatch(Unk nown*Source)
****at*java.awt.EventQueue.dispatchEvent(Unknown*S ource)
****at*java.awt.EventDispatchThread.pumpOneEventFo rFilters(Unknown*Source)
****at*java.awt.EventDispatchThread.pumpEventsForF ilter(Unknown*Source)
****at*java.awt.EventDispatchThread.pumpEventsForH ierarchy(Unknown*Source)
****at*java.awt.EventDispatchThread.pumpEvents(Unk nown*Source)
****at*java.awt.EventDispatchThread.pumpEvents(Unk nown*Source)
****at*java.awt.EventDispatchThread.run(Unknown*So urce)
net.sf.jasperreports.engine.design.JRValidationExc eption:*Report*design*not*valid*:*
*****1.*java.lang.ClassNotFoundException:*Template ReportClass
****at*net.sf.jasperreports.engine.design.JRAbstra ctCompiler.verifyDesign(JRAbstractCompiler.java:26 0)
****at*net.sf.jasperreports.engine.design.JRAbstra ctCompiler.compileReport(JRAbstractCompiler.java:1 44)
****at*it.businesslogic.ireport.IReportCompiler.ru n(IReportCompiler.java:591)
****at*java.lang.Thread.run(Unknown*Source)
In Ant I see the following:
Buildfile: C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\build.xml
_checkrelease:
[echo]
[echo] The current release of this plug-in is version:
[echo] "1" --> (Testing Test av rapportlaging_6.1r1)
[echo] Do you want to increment the release number and create a
new release?
_newrelease:
_init:
[echo] Author information loaded from
C:\proj\content/dev/dev.properties
_typeInit:
scrub:
build-release:
_build-checks:
_init:
[echo] Author information loaded from
C:\proj\content/dev/dev.properties
_typeInit:
build-zip:
[delete] Deleting directory
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1
_copy-plugin:
[copy] Copying 1 file to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[copy] Copying 1 file to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\tmp
[copy] Copying 9 files to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[copy] Copying 6 files to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[copy] Copying 2 files to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[copy] Copying 1 file to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[copy] Copying 1 file to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[move] Moving 1 file to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[javac] Compiling 1 source file to
C:\proj\content\build\Testing_Test-av-rapportlaging_6.1r1\plugin
[javac] C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\TemplateReportScriptlet.java:4: package
it.businesslogic.ireport does not exist
[javac] public class TemplateReportScriptlet extends
it.businesslogic.ireport.IReportScriptlet {
[javac]
^
[javac] C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\TemplateReportScriptlet.java:24: cannot find symbol
[javac] symbol : variable super
[javac] location: class TemplateReportScriptlet
[javac] super.beforeColumnInit();
[javac] ^
[javac] C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\TemplateReportScriptlet.java:30: cannot find symbol
[javac] symbol : variable super
[javac] location: class TemplateReportScriptlet
[javac] super.afterDetailEval();
[javac] ^
[javac] C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\TemplateReportScriptlet.java:36: cannot find symbol
[javac] symbol : variable super
[javac] location: class TemplateReportScriptlet
[javac] super.afterGroupInit(groupName);
[javac] ^
[javac] C:\proj\content\dev\reports\Testing\Test av
rapportlaging\6.1\TemplateReportScriptlet.java:42: cannot find symbol
[javac] symbol : variable super
[javac] location: class TemplateReportScriptlet
[javac] super.afterPageInit();
[javac] ^
[javac] 5 errors
As I recall, I can fix this by adding the right .JAR file to the dev
directory of the report, so it's not a huge problem.
2) When I try to preview a report with an active connection I get the
following error:
net.sf.jasperreports.engine.JRRuntimeException:
net.sf.jasperreports.engine.JRException: Class
com.novell.jasper.data.event.LuceneEventQueryExecu torFactory not found
This is something I haven't found a fix for, unfortunately. Any ideas?
PS:
My apologies for the late reply - I was on holiday last week and was
swamped both before going and once I got back.
Ragnar Storstrm
rstorstrom
rstorstrom's Profile: http://forums.novell.com/member.php?userid=5064
View this thread: http://forums.novell.com/showthread.php?t=429304

Problem in Data extraction for NEW GL DSO 0FIGL_O10

Hi ,
I am facing Problem in extraction of records from SAP to BW.
I have installed Business Content of NEW GL DSO 0FIGL_O10.
When I extract the Data from SAP R/3, to this DSO ( 0FIGL_O10 ) the reocrds are getting over written
For Example When I go the the Mange Option ( InfoProvider Administration) the transferred Records and the Added Records are not same. The Added records are less then the Transfered reocords.
This is happening becuase of Key Filed Definations.
I have 16 Characterisics in the KEY FIELD, which the maximum that I can have. But the Data comming from is Unique in some casses.
As result the data get added up in the DSO, hence my balances are not matching with SAP R/3 for GL Accounts.
There are total 31 Characteristics in the Datasource (0FI_GL_10) . Of which 16 Charactheristics i can include in the Key field area.
Please suggest some solution.
Regards,
Nilesh Labde

Hi,
For safety, the delta process uses a lower interval setting of one hour (this is the default setting). In this way, the system always transfers all postings made between one hour before the last delta upload and the current time. The overlap of the first hour of a delta upload causes any records that are extracted twice to be overwritten by the after image process in the ODS object with the MOVE update. This ensures 100% data consistency in BW.
But u can achive ur objective in different manner::
Make a custom info object ZDISTINCT and populate it in transformation using ABAP code. In ABAP try and compound the values from different charactersitcs so that 1 compounded characterstic can be made. Use ZDISTINCT in ur DSO as key
Just a thought may be it can solve ur problem.
Ravish.

Problem setting data collection for SLD

Similar Messages

Maybe you are looking for