Problem setting up router

Okay, I have a WRT54G router. However, I can't get it setup. I've tried at LEAST 10 times following the instructions on the setup CD exactly.
The setup wizard currently says:
The router is not able to connect to the Internet. Try turning the Cable/DSL Modem OFF and back ON again. Do you want to try again?
Doesn't work. I then retry and it brings me to a wireless configuration screen. I fill everything out. It goes through saving settings. Then it says:
Unable to connect to the Rounter. Check the cable connection from the computer to the Router.
What am I doing wrong? Please help.
I'm trying to set this up for my laptop (Sony VAIO) and set up a wireless connection, while maintaining the PC conection and xbox live.
Thanks,

Don't run the CD again if you have established a working internet connection for the wired computers. Go to http://192.168.1.1/ and configure the wireless there. Then connect the computer wireless to the router. It is very important to change the SSID from "linksys" to something unique. Otherwise you'll never know whether you connect to your router or your neighbor's.
If it does not work please post exactly what does not work and what error messages you get.

Similar Messages

Problem setting 7606 router for TACACS+ authentication

Hello Support Community,
I have two Cisco 7606 routers which I have tried in vain to have users authenticated using TACACS+ servers. As shown below, I have two servers (1.1.1.1 and 2.2.2.2) reachable via vrf OAM which is reachable from desktops for ssh login. The true IP addresses and vrf have been altered because it's a company router.
I use the two servers to authenticate many other Cisco devices in the network they are working fine.
I can reach the servers from the vrf and the source interface in use. I can also telnet port 49 if the servers from the source interface and the vrf.
The server key is hidden but at the time of configuration, I can ascertain that it's correct.
The problem is that after confuring for TACACS authentication, the router still uses the enable password instead of TACACS. While the debug output shows 'bad password', why is the router not authenticating using TACACS? Why is it using the enable password?
Please study the outputs below and help point out what I may need to change.
PS: I have tried out many other combinations, including deprecated ones without success including the method suggested in this page;
http://www.cisco.com/en/US/docs/ios/sec_user_services/configuration/guide/sec_vrf_tacas_svrs.html
Please help I'm stuck.
ROUTER#sh running-config | sec aaa
aaa new-model
aaa group server tacacs+ admin
server name admin
server name admin1
ip vrf forwarding OAM
ip tacacs source-interface GigabitEthernet1
aaa authentication login admin group tacacs+ local enable
aaa session-id common
ROUTER#sh running-config | sec tacacs
aaa group server tacacs+ admin
server name admin
server name admin1
ip vrf forwarding OAM
ip tacacs source-interface GigabitEthernet1
aaa authentication login admin group tacacs+ local enable
tacacs server admin
address ipv4 1.1.1.1
key 7 XXXXXXXXXXXXXXXXXXXX
tacacs server admin1
address ipv4 2.2.2.2
key 7 XXXXXXXXXXXXXXXXxxxx
line vty 0 4
login authentication admin
ROUTER#sh tacacs
Tacacs+ Server - public :
               Server name: admin
            Server address: 1.1.1.1
               Server port: 49
              Socket opens:         15
             Socket closes:         15
             Socket aborts:          0
             Socket errors:          0
           Socket Timeouts:          0
   Failed Connect Attempts:          0
        Total Packets Sent:          0
        Total Packets Recv:          0
Tacacs+ Server - public :
               Server name: admin1
            Server address: 2.2.2.2
               Server port: 49
              Socket opens:         15
             Socket closes:         15
             Socket aborts:          0
             Socket errors:          0
           Socket Timeouts:          0
   Failed Connect Attempts:          0
        Total Packets Sent:          0
        Total Packets Recv:          0
Oct 22 12:38:57.587: AAA/BIND(0000001A): Bind i/f
Oct 22 12:38:57.587: AAA/AUTHEN/LOGIN (0000001A): Pick method list 'admin'
Oct 22 12:38:57.587: AAA/AUTHEN/ENABLE(0000001A): Processing request action LOGIN
Oct 22 12:38:57.587: AAA/AUTHEN/ENABLE(0000001A): Done status GET_PASSWORD
Oct 22 12:39:02.327: AAA/AUTHEN/ENABLE(0000001A): Processing request action LOGIN
Oct 22 12:39:02.327: AAA/AUTHEN/ENABLE(0000001A): Done status FAIL - bad password
Oct 22 12:39:04.335: AAA/AUTHEN/LOGIN (0000001A): Pick method list 'admin'
Oct 22 12:39:04.335: AAA/AUTHEN/ENABLE(0000001A): Processing request action LOGIN
Oct 22 12:39:04.335: AAA/AUTHEN/ENABLE(0000001A): Done status GET_PASSWORD
Oct 22 12:39:08.675: AAA/AUTHEN/ENABLE(0000001A): Processing request action LOGIN
Oct 22 12:39:08.675: AAA/AUTHEN/ENABLE(0000001A): Done status FAIL - bad password
Oct 22 12:39:10.679: AAA/AUTHEN/LOGIN (0000001A): Pick method list 'admin'
Oct 22 12:39:10.683: AAA/AUTHEN/ENABLE(0000001A): Processing request action LOGIN
Oct 22 12:39:10.683: AAA/AUTHEN/ENABLE(0000001A): Done status GET_PASSWORD
Oct 22 12:39:14.907: AAA/AUTHEN/ENABLE(0000001A): Processing request action LOGIN
Oct 22 12:39:14.907: AAA/AUTHEN/ENABLE(0000001A): Done status FAIL - bad password
ROUTER#sh ver
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1(3)S3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 30-Mar-12 08:34 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRE, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1(3)S3, RELEASE SOFTWARE (fc1)
ROUTER uptime is 7 weeks, 5 days, 16 hours, 48 minutes
Uptime for this control processor is 7 weeks, 5 days, 16 hours, 49 minutes
System returned to ROM by reload (SP by reload)
System restarted at 20:00:59 UTC Wed Aug 28 2013
System image file is "sup-bootdisk:c7600rsp72043-advipservicesk9-mz.151-3.S3.bin"
Last reload type: Normal Reload
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO7606-S (M8500) processor (revision 1.1) with 3670016K/262144K bytes of memory.
Processor board ID FOX1623G61B
BASEBOARD: RSP720
CPU: MPC8548_E, Version: 2.1, (0x80390021)
CORE: E500, Version: 2.2, (0x80210022)
CPU:1200MHz, CCB:400MHz, DDR:200MHz,
L1:    D-cache 32 kB enabled
        I-cache 32 kB enabled
Last reset from power-on
3 Virtual Ethernet interfaces
76 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
3964K bytes of non-volatile configuration memory.
500472K bytes of Internal ATA PCMCIA card (Sector size 512 bytes).
Configuration register is 0x2102

In order to resolve this issue. Please replace the below listed command
aaa authentication login admin group tacacs+ local enable
with;
aaa authentication login default group admin local enable
You defined the server group name as method list and instead of using admin as a server-group, you used tacacs+
Note: Please ensure you have local user and enable password configured in case of tacacs server unreachable.
~BR
Jatin Katyal
**Do rate helpful posts**

Problems setting up static routing

HI
I'm having a problem setting up static routing. I keep getting the message "invalid static route". I have an E1550 router and my frimware is up to date. I have tried a few different gateway addresses ie 192.168.1.1, 127.0.0.1 and my router's address on the net, but I keep getting the same message. Has anyone else had this problem and been able to fix it?

I think the E1550 router supports LAN to LAN routing provided that you have two local networks. If you only have a plain modem and the E1550, I believe you can't do Static routing on that type of setup. Found this link that might help: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=12a84336a124498eb5d6f0204b85191e_17589.xml&pid=80&...

Problems setting up WRT54G2 router

I'm having problems setting up my Linksys WRT54G2 router. I want my mac laptop (iBook G3 running OSX) to use a wireless connection, and the home computer (running Windows XP) to stay connected to the modem.
I originally tried to set up the router by connecting it via ethernet to my laptop (and by ethernet to the modem), and went into the 192.168.1.1 address to configure it. The internet works fine on my laptop when connected to the wireless by ethernet but it can't connect wirelessly (it has an original airport card fitted, at first I thought I might need to upgrade the firmware but I ran a software update and one didn't come up). I then realised that I would need to MAC clone from the PC, that is connected to the modem? I tried to do this today, but I couldn't access the 192.168.1.1 address from the PC. I have tried resetting the router, and disabling the firewall but still can't access it. This PC also has anti-virus software running too - could this be the problem, or am I setting it up wrong? Thanks.

If you are trying to Setup your Router with the setup disk, Then you can exit from the setup and configure your Router manually. Before you configure your router, you need to Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 60 seconds and re-connect the power cable.....
You need to connect your Modem to Linksys Router on Internet Port and your Computer to Linksys Router on Port No.1.
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link
Here are the Wireless Settings which you can set on your router, once done you can try connecting your MAC computer to your Wireless network and check if you are Online from MAC computer.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
-Here select manual configuration...Wireless Network mode should be mixed...
-Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on save settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2307 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Problems setting up my TC. Have just bought new iMac(OS 10.6.8) and TC. I set it up. iMac cannot find it. I have tried direct connection with an ethernet cable to Mac or my wireless router but nothing. Just a flashing orange light. Help for a simpleton p

Problems setting up my TC. Have just bought new iMac(OS 10.6.8) and TC. I tried to set it up. iMac cannot find it. I have tried direct connection with an ethernet cable to Mac or direct to my wireless router but nothing. Just a flashing orange light. Help for a simpleton please. Have tried reseting TC, but to no avail.

Just updated from 10.6.7 ---> 10.6.8 and had the same issue. Despite having done a clean install from 10.6 and got everything back off my TC, now Time Machine can't find it!
Green light is on, ethernet cable conected, network CP says its conected but nothing. Airport Utility can't find it. Hit reset button, Orange flashing light but still no show in Airport Utility.
But I know its there, as rebooting from 10.6 SL disk shows the backups are still ok?
Hmm, ideas anyone?
SBB

Problems Setting up a Direct Debit

has anyone experienced any problems setting up a direct debit ??
I've been a BT customer for approximately 20 years and have had the same account number. I've moved house a few times and retained the same account. My last house move wasn't so successful as after moving in and having broadband re set up again... I received a letter in the post saying I had requested a "termination" and a parcel was included to send my router back etc... plus... I'd be charged £100+ for the disconnection...
Anyway I got on the phone to BT and the advisor appologised for the mix up... and suggested I cancel my direct debit with the bank to make sure the disconnection fee wasn't taken from my account.....
Ever since then... I have not being able to set up a direct debit online or by speaking with several BT helpdesk staff. I email BT asking for an explaination - NOTHING. BT helpdesk staff assure me that the direct debit will work this time and will contact me if there is a problem... again NOTHING. I even tried writing a letter to the head of customer services... I think the name Warren Buckley rings a bell.. Someone did email me back suggesting I use the online facility.... REALLY!! Do BT not have a fault tracking database of customer issues... so they can see I've already tried to set up the direct debit online...
Anyway ..... I've just noticed this forum now... so this is my latest attempt to see if anyone senior enough at BT will be embarrassed and try and sort out my account so I can start paying my bill using Direct Debit again... I'm pretty sure all that needs to happen is to be given a new account number or an account alias that can be sent to my bank. Otherwise... I'll just carry on waiting to receive the automated message from BT saying I haven't paid and then go and pay online... But I am worried one of these automated messages will arrive the day I go on a 2 week holiday and I find myself cut off when I get home... giving me more pain....
PLEASE HELP BT ;o)
regards
DaveB

I have asked a moderator to provide assistance, they will post an invite on this thread.
They are the only BT employees on this forum, and are a UK based team of people, who take personal ownership of your problem.
Once you get a reply, if you click on their name, you will see a screen like this. Click on the link as shown below.
Please do not send them a personal message, as they may not be on duty for a long time, and your message will not be tracked properly.
For your own security, do not post any personal details, on this forum. That includes any tracking number you are give.
They will respond either by phone or e-mail within 5-6 working days.
Please use the tracked e-mail, to reply, not via the forum. Thanks
This is the form you should see when you click on the link. If you do not see this form, then you have selected the wrong link.
When you submit the form, you will receive an enquiry number, so please keep a note of it
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Problems setting up MPLS

A Chairde,
Am having problems setting up MPLS between a AS5350 and 7609 , I have used commands stated in this link, enable MPLS incrementally on a network.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/switch_c/xcprt4/xcdtagc.pdf
The commands below are added to each router, and some troubleshooting.
7609
ip cef distributed
interface Loopback0
ip address 192.168.254.1 255.255.255.255
tag-switching advertise-tags
interface GigabitEthernet3/12
ip address 192.168.230.162 255.255.255.248
mpls label protocol tdp
tag-switching ip
AS5350
ip cef
mpls label protocol tdp
tag-switching advertise-tags
interface Loopback0
ip address 192.168.254.2 255.255.255.255
interface FastEthernet0/0
ip address 192.168.230.161 255.255.255.248
duplex auto
speed auto
mpls ip
h323-gateway voip interface
h323-gateway voip id cnibhco111 ipaddr 192.168.230.129 1719
h323-gateway voip h323-id cnibhco112
h323-gateway voip tech-prefix 71401
h323-gateway voip tech-prefix 0030
h323-gateway voip bind srcaddr 192.168.230.161
ip rsvp bandwidth 64 64
cnibhco112#sh tag-switching tdp neighbor
Peer TDP Ident: 192.168.254.1:0; Local TDP Ident 192.168.230.161:0
TCP connection: 192.168.254.1.49842 - 192.168.230.161.711
State: Oper; PIEs sent/rcvd: 18/23; Downstream
Up time: 00:12:54
TDP discovery sources:
FastEthernet0/0, Src IP addr: 192.168.230.162
Addresses bound to peer TDP Ident:
192.168.100.17 192.168.100.25 159.107.212.49 172.16.8.81
192.168.230.130 192.168.230.77 192.168.230.81 192.168.254.1
192.168.210.6 192.168.127.6 192.168.210.106 192.168.127.66
192.168.127.138 192.168.210.146 192.168.210.142 192.168.210.122
192.168.210.17 192.168.230.140 192.168.230.26 192.168.230.74
192.168.230.10 192.168.230.14 192.168.127.130 192.168.127.142
192.168.230.6 192.168.230.70 192.168.230.34 192.168.210.178
192.168.200.25 192.168.210.126 192.168.232.1 192.168.231.1
192.168.200.17 192.168.210.102 190.168.200.245 190.168.200.225
190.168.201.241 192.168.230.98 192.168.210.14 190.168.201.201
190.168.201.209 192.168.210.162 192.168.210.210 190.168.201.205
192.168.230.38 190.168.200.249 190.168.200.217 190.168.200.253
192.168.230.162
cnibhco112#
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
cnibhco112#traceroute 192.168.254.1
Type escape sequence to abort.
Tracing the route to 192.168.254.1
1 192.168.230.162 0 msec 0 msec *
cnibhco112#traceroute 192.168.230.162
Type escape sequence to abort.
Tracing the route to 192.168.230.162
1 192.168.230.162 0 msec 0 msec *
cnibhco112#

Ro,
Thanks for the respone, have been playin, with MPLS for last few hours.
The routing between the loopbacks is now working, can PING 7609 Loopback from AS5350 ,and vice versa. (used static routes).
Having problem with TDP / LDP on routers,
mpls label protocol ldp / tdp command works correctly on both routers, but the
tag-switching tdp router-id Loopback0 force
command works on the 7609, but when I add it onto the AS5350 , the command "mpls ldp router-id Loopback0 force" appears on the startup script.
The opposite is true for the 7609 , you add MPLS LDP command, and TAG-SWITCHING command appears instead.
Any Ideas, as different configs of this leave me with forwarding table with both tags added, but not been able to ping the loopbacks !!!
When I can ping bot loopbacks, the OUTGOING TAG , disapears.....
Problem is LOOPBACK Commands on bot routers default to LDP (AS5350) , or TDP (7609). Any Ideas ...
mpls label protocol tdp
tag-switching tdp router-id Loopback0 force
mpls label protocol tdp
mpls ldp router-id Loopback0 force
cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
Local Outgoing Prefix Bytes tag Outgoing Next Ho
tag tag or VC or Tunnel Id switched interface
18 17 192.168.254.0/24 0 Gi3/12 192.168.2
MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
00097CA3293000127FCDBA808847 00011000
No output feature configured
Per-packet load-sharing
cnibhco100#traceroute 192.168.254.2
Type escape sequence to abort.
Tracing the route to 192.168.254.2
1 192.168.230.161 [MPLS: Label 17 Exp 0] 0 msec 0 msec 0 msec
2 192.168.230.162 0 msec 0 msec 0 msec
But no PINGING 192.168.254.2
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
17 18 192.168.254.0/24 1915668 Fa0/0 192.168.230.162
MAC/Encaps=14/18, MRU=1500, Tag Stack{18}
00127FCDBA8000097CA329308847 00012000
No output feature configured
Per-packet load-sharing
cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
Local Outgoing Prefix Bytes tag Outgoing Next Ho
tag tag or VC or Tunnel Id switched interface
18 17 192.168.254.0/24 752551 Gi3/12 192.168.2
MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
00097CA3293000127FCDBA808847 00011000
No output feature configured
Per-packet load-sharing
WHEN BOTH LOCAL AND OUTGOING TAG, CANNOT PING EITHER WAY !!!
HAVE LABEL PROTOCOL AND LOOPBACK FORCE on AS5350
HAVE LABEL PROTOCOL ON 7609
WHEN ADD LOOPBACK FORCE on 7609 , CAN PING BOTH LOOPBACKS,
BUT OUTGOING TAG DISAPEARS
cnibhco112#PING 192.168.254.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.254.2, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
17 Untagged 192.168.254.0/24 598678 Fa0/0 192.168.230.162
MAC/Encaps=0/0, MRU=1504, Tag Stack{}
No output feature configured
Per-packet load-sharing
cnibhco112#
mpls label protocol tdp
tag-switching tdp router-id Loopback0 force

Problems setting up Time Machine using a network drive

I am having problems setting up TimeMachine on my Mac Mini to work with a WD MyBookLive network drive. The network drive came with a TimeMachineBackup shared folder preconfigured. When I first connected the drive to the router and turned on TimeMachine, the TimeMachineBackups appeared as an option when I did "Select Backup Disk" from TimeMachine Preferences.
I managed to successfully connect to the drive and start a backup running. However the backup hit a problem and I started getting an error that the "disk was already in use". I therefore tried to remove the disk to try and start again. Hoever when I now do go into "Select Backup Disk" from TimeMachine Preferences the shared folder on the drive no longer apperas and I only get the option to serach for an Time Capsule.
If I go into Finder, the MyBookLive shows up as a connected Device with all its shared folders showing (including the TimeMachineBackup folder) and my Mac is definitely connected to the drive. How do I get the Drive & TimeCapsuleBackup shared folder to reappear in TimeMachine Preferences so that I can select it as the destination for my backups?

Check around the forum, you are one of very very many. It doesn't matter what WD say, do you see a Certified by Apple notice on it?
Go here, most authoritative site about Time Machine you can find. http://pondini.org/OSX/Home.html
Specific info on Network Drives are here http://pondini.org/TM/2.html
Post back here and ask for Pondini if you need more.
You can also read some tales of woe here

Problem with E2000 Router

I have a problem getting my router to work on any channel other than channel 11. There are 4 other houses on my street that uses channel 11 and it causes a lot of interference. I tried switching to channel 1 or 6 but everytime I do my router does not show up in the list of Networks on any of my wireless devices. Help is much appreciated

As you mentioned in your post that you tried switching off the channel1 or 6 but your wireless network does not show up in the list. You even tried channel number 11 but that is even used by your 4 neighbor. So you can change the channel to 9. Channel 9 is one of the channel for best optimized setting...

Problem setting up WDS with MSI RG54GS2 & Motorola WR850g

Problem setting up WDS with WR850g & MSI RG54GS2
Hi,
I'm trying to bridge 2 routers: Motorola WR850g & MSI RG54GS2 .
I set the MSI as the main router (it works better for me as a router than the Moto), and the Moto is the repeater. I have set it up exactly as the guide on Broadbandreports.com for the Motorola , and on Tom's Networking http://www.tomsnetworking.com/2004/04/14/how_to_wds_bridge/
The Moto sees the MAC of the MSI (Status is UP), the MSI doesn't have a page that shows WDS MACs . I know the routers are connected because when I connect a laptop to the Moto wireless network, it gets an IP (and the DHCP on the Moto is disabled) and the default gateway of the connection is the IP of the main (MSI) router.
The problem is I can't surf anywhere. I can't even ping the MSI router - which should be possible if the WDS works properly.The Moto Wireless Bridge Operation is set properly to Access Point/Wireless Bridge .
Can anyone solve this?
Thanks.

David, welcome to the discussions.
Are you refering to Airport Extreme Setup as the Extreme base.
Or are you using a 3rd party Router as your primary Base, or the Express as the primary base.
Read the supplied link, Not all 3rd party routers are WDS compatible.
http://discussions.apple.com/thread.jspa?messageID=2785566
Who is you Internet Service Provider?
What brand and Model Modem did they furnish?
Are you using Dial-Up...DSL...or Cable?
http://docs.info.apple.com/article.html?artnum=303595
See if there is any help from this link.
http://discussions.apple.com/thread.jspa?messageID=607414
Cheers Don

Problems after wireless router (WRT310n) firmware update.

I updated the firmware on my wireless router (wrt310n) yesterday and now I am having major issues connecting my laptop to it via wireless. After the update, I reset the router as well as unplugged the power source. Once the update and everything was reset, I re-entered all my settings and set the computers back up using the LELA. I go to change the laptop to wireless and it says it can't connect to it. I did the LELA update on the laptop thinking that would fix it, but it didn't help. However, the whole time I am able to connect to the router using a ethernet cable. I turned off all of the encryption settings, firewalls, and broadcasted my SSID. I searched this forum for some help and one topic suggested somethings, which I did, and I was able to connect wirelessly with the encryption. I thought I was done and set-up, until later that evening. I turned the computer back on only to see the same problem again. I decided to deal with it the next day (today) by uninstalling LELA and just using Windows to configure my wireless settings. As soon as I uninstalled LELA, entered the key into the Windows program, it worked like a charm. Until tonight, when I turned on the computer. Now I'm connecting to the network wirelessly, but it says "Limited or no connectivity." Acting like there is no encryption key entered. I go to "View Wireless Networks" and it says "WIndows cannot configure connection. If you have another program to manage this wireless connection, use that software." The thing is, I don't have another program on here to manage a wireless connection. Sorry for the long post. I figured if I didn't type everything out, people would have just asked me questions. I had no problems with this router until I did the update yesterday. If it can't be fixed, is there a way to revert back to the old firmware? Thanks in advance.

Well you should adjust the Wireless Settings on your router...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...
Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Before you attempt to connect to your wireless network you should first check your Programs menu if there is any Wireless Program(like 'Intel Proset' , 'Dell Wireless WLAN' , or anything that gives you a clue of a Wireless Program/Utility/Software)...You should use the Wireless Utility/Software(if any) to connect to your wireless network and not the Windows default Wireless Program to avoid any conflicts...

Problems setting up username & password for SQL

Due to the outstanding advice I recieved from this excellent forum, I have managed to overcome my first problem with declaring a new Class.
This leads me to request help with my next biggest problem:
Setting up a user GUI that takes a "username" & "password" that will be used to access a password protected database.
I am a simple bloke, with simple thought processes, so please, go easy on me...
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery1 {
     String username = "" , password = "";
     public static void main(String[] arguments) {
          PassDB UPass = new PassDB();
          String data = "jdbc:odbc:JavaTestDataBase";
          try {
               Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
               Connection conn = DriverManager.getConnection(data, "" + username, "" + password);
               Statement st = conn.createStatement();
               ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
          catch (SQLException s) {
               System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
          catch (Exception e) {
               System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     String username = "", password = "";
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          username = uname.getText();
          password = pword.getText();
This code generates two errors, stating:
C:\Java_progs>javac DBQuery1.java
DBQuery1.java:14: non-static variable username cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
^
DBQuery1.java:14: non-static variable password cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
                ^
2 errors*****************************
The code works when I remove the reference to the variables "username" & "password" in Connection "conn" call & replace them with the actual username & password, but this is not exactly what I was after. I was hoping to make the program responsive to each individual user, not set in code.
I also would like to make the program pause after the call in "main" to "PassDB" to wait for "PassDB" to exit before continuing.
I would also like to make "PassDB" destroy itself after the "OK" button is pressed & the "username" & "password" set.
If that isn't enough for you, I would really like the program to search 2 different database tables, return their values & compare them to be sure that they are the same.
When I try & search 2 different tables, as in:
ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
               ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID")javac tells me that "ResultSet" is set to null 0
As always, I am extremely appreciative of any assistance you are able to offer.
Kind regards
duBedat
[email protected]

This is where I'm at now:
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery {
     static String username = "" ;
     static String password = "" ;
     public static void main(String[] arguments) {
     PassDB UPass = new PassDB();
     String data = "jdbc:odbc:JavaTestDataBase";
     try {
          Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
          Connection conn = DriverManager.getConnection(data, "" + DBQuery.username, "" + DBQuery.password);
          Statement st = conn.createStatement();
          ResultSet rec = st.executeQuery(
          "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
          + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
               "SELECT Subject, ContactID FROM Calls "
               + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
     catch (SQLException s) {
          System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
     catch (Exception e) {
          System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     static boolean getOut = false;
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     public PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          while(getOut == false)
               setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          DBQuery.username = uname.getText();
          DBQuery.password = pword.getText();
          getOut = true;
}          Any advice is greatly appreciated
duBe

Problems setting up an NFS server

Hi everybody,
I just completed my first arch install. :-)
I have a desktop and a laptop, and I installed Arch on the desktop (the laptop runs Ubuntu 9.10). I had a few difficulties here and there, but I now have the system up and running, and I'm very happy.
I have a problem setting up an NFS server. With Ubuntu everything was working, so I'm assuming that the Ubuntu machine (client) is set-up correctly. I'm trying to troubleshoot the arch box (server) now.
I followed this wiki article: http://wiki.archlinux.org/index.php/Nfs
Now, I have these problems:
- when I start the daemons, I get:
[root@myhost ~]# /etc/rc.d/rpcbind start
:: Starting rpcbind [FAIL]
[root@myhost ~]# /etc/rc.d/nfs-common start
:: Starting rpc.statd daemon [FAIL]
[root@myhost ~]# /etc/rc.d/nfs-server start
:: Mounting nfsd filesystem [DONE]
:: Exporting all directories [BUSY] exportfs: /etc/exports [3]: Neither 'subtree_check' or 'no_subtree_check' specified for export "192.168.1.1/24:/home".
Assuming default behaviour ('no_subtree_check').
NOTE: this default has changed since nfs-utils version 1.0.x
[DONE]
:: Starting rpc.nfsd daemon [FAIL]
- If I mount the share on the client with "sudo mount 192.168.1.20:/home /media/desktop", IT IS mounted but I can't browse it because I have no privileges to access the home directory for the user.
my /etc/exports looks like this:
# /etc/exports: the access control list for filesystems which may be exported
# to NFS clients. See exports(5).
/home 192.168.1.1/24(rw,sync,all_squash,anonuid=99,anongid=99))
/etc/conf.d/nfs-common.conf:
# Parameters to be passed to nfs-common (nfs clients & server) init script.
# If you do not set values for the NEED_ options, they will be attempted
# autodetected; this should be sufficient for most people. Valid alternatives
# for the NEED_ options are "yes" and "no".
# Do you want to start the statd daemon? It is not needed for NFSv4.
NEED_STATD=
# Options to pass to rpc.statd.
# See rpc.statd(8) for more details.
# N.B. statd normally runs on both client and server, and run-time
# options should be specified accordingly. Specifically, the Arch
# NFS init scripts require the --no-notify flag on the server,
# but not on the client e.g.
# STATD_OPTS="--no-notify -p 32765 -o 32766" -> server
# STATD_OPTS="-p 32765 -o 32766" -> client
STATD_OPTS="--no-notify"
# Options to pass to sm-notify
# e.g. SMNOTIFY_OPTS="-p 32764"
SMNOTIFY_OPTS=""
# Do you want to start the idmapd daemon? It is only needed for NFSv4.
NEED_IDMAPD=
# Options to pass to rpc.idmapd.
# See rpc.idmapd(8) for more details.
IDMAPD_OPTS=
# Do you want to start the gssd daemon? It is required for Kerberos mounts.
NEED_GSSD=
# Options to pass to rpc.gssd.
# See rpc.gssd(8) for more details.
GSSD_OPTS=
# Where to mount rpc_pipefs filesystem; the default is "/var/lib/nfs/rpc_pipefs".
PIPEFS_MOUNTPOINT=
# Options used to mount rpc_pipefs filesystem; the default is "defaults".
PIPEFS_MOUNTOPTS=
/etc/hosts.allow:
nfsd: 192.168.1.0/255.255.255.0
rpcbind: 192.168.1.0/255.255.255.0
mountd: 192.168.1.0/255.255.255.0
Any help would be very appreciated!

Thanks, I finally got it working.
I realized that even though both machines had the same group, my Ubuntu machine (client) group has GID 1000, while the Arch one has GID 1001. I created a group that has GID 1001 on the client, and now everything is working.
I'm wondering why my Arch username and group both have 1001 rather than 1000 (which I suppose would be the default number for the first user created).
Anyway, thanks again for your inputs.

Problems Setting Up Developer Users

I am having a problem setting up developer users and I am trying to determine if I am missing a step or if there is a configuration problem on my staging and production systems.
What I want to do should be very simple. I want to create a user that can create an application and see the information under the "Application" tab in the Navigator.
I have created the user using the following steps on 3.0.9.82 for Unix:
1. Create the user
2. Make the user a full administrator (rather than end user)
3. Make the user a member of the portal_developers group
4. Make the user's default group the portal_developers group
However, when I do this the user does not see the information under the
"Application" tab. The only way I can get the user to see the info under the
"Application" tab is to make him a member of the Portal_administrators
and/or DBA group. Both my staging and production boxes have the same result.
Does anyone have any thoughts or suggestions on what might be happening?

Thank you- I have read through that thread and can see some resonance with my issue.
My AOL emails work VERY fast with BB, in fact almost simultaneously received on PC & Torch " ping ping!"
This issue only raised its ugly head when I had 2 Torches replaced by my insurers.
Whilst the claim was in process I used a new Curve, loaded from backup on PC to keep emails going and of course phone & web facilities. ( I use the BB to power internet via bluetooth to my PC / laptop when living on a remote island with no phone lines or power supplies) All was fine. Swapping email accounts took a few minutes with the usual password confirmations for each AOL screenname etc.
Then the new Torches came back from insurers, and I tried to swap devices. Phoning & texting is fine. Al data and contacts swap over fine.
SETUP email accounts.............stymied every time. It says repeatedly that my user name/password is invalid etc etc etc
Have tried security wipes. Have tried setting up new BB ID & passwords on PC website. All is OK until I try to setup emails on the Torches. This has used up ridiculous amounts of time- all wasted.
I love the BB phones and the fast email push......in fact I recently bought a new Sony Xperia Z1 but sent it back because of wifi coverage meant no emails on that superb phone for lots of the time.
Good old BB I said..........I always get emails wherever I am. ( Rural Scotland has very patchy radio & wifi coverage)
Was about to purchase new Z10s just to get a bigger screen, but now I am averse to buying ANY BB phone again because this present mess means I may never get emails set up again. How nuts is that?
Many thanks for all help & suggestions..........boy do I need them!!
Kind wishes from West of Scotland
Fair winds and kind landfalls

Problems setting up VVSA 6.0 (lookup service adresse)

Hi,
I was happy to see VVSA 6.0 released, but i'm having problems setting it up. It keeps saying that the lookup service adresse is not reachable. But I have tried with the VVSA 5.5 and 5.5.1.1 and they work just fine with the lookup service adresse.
Anyone else having this issue?
Also trying to check for updates within the appliance failes since the repository is not online at vmware it seems.
Might not be ready for primetime (like ESXi6).

If Developer has a separate Oracle Home on your PC, then it has a separate TNSNAMES.ORA file that is uses to connect to the database. If you search for all tnsnames.ora files, you should find the one used by Developer 6.
Since Enterprise manager works, the tnsnames.ora in your Enterprise Manager's home will have an entry for your server database. You should be able to cut and paste this into the tnsnames.ora file used by Developer, or try copying the E.M. tnsnames.ora file directly.
John Alexander www.SummitSoftwareDesign.com

Problem setting up router

Similar Messages

Maybe you are looking for