Problem setting up WDS with MSI RG54GS2 & Motorola WR850g

Problem setting up WDS with WR850g & MSI RG54GS2
Hi,
I'm trying to bridge 2 routers: Motorola WR850g & MSI RG54GS2 .
I set the MSI as the main router (it works better for me as a router than the Moto), and the Moto is the repeater. I have set it up exactly as the guide on Broadbandreports.com for the Motorola , and on Tom's Networking http://www.tomsnetworking.com/2004/04/14/how_to_wds_bridge/
The Moto sees the MAC of the MSI (Status is UP), the MSI doesn't have a page that shows WDS MACs . I know the routers are connected because when I connect a laptop to the Moto wireless network, it gets an IP (and the DHCP on the Moto is disabled) and the default gateway of the connection is the IP of the main (MSI) router.
The problem is I can't surf anywhere. I can't even ping the MSI router - which should be possible if the WDS works properly.The Moto Wireless Bridge Operation is set properly to Access Point/Wireless Bridge .
Can anyone solve this?
Thanks.

David, welcome to the discussions.
Are you refering to Airport Extreme Setup as the Extreme base.
Or are you using a 3rd party Router as your primary Base, or the Express as the primary base.
Read the supplied link, Not all 3rd party routers are WDS compatible.
http://discussions.apple.com/thread.jspa?messageID=2785566
Who is you Internet Service Provider?
What brand and Model Modem did they furnish?
Are you using Dial-Up...DSL...or Cable?
http://docs.info.apple.com/article.html?artnum=303595
See if there is any help from this link.
http://discussions.apple.com/thread.jspa?messageID=607414
Cheers Don

Similar Messages

Problems setting up WDS with AE

I recently had some problems with my home network and performed a hard reset on both of my AE base stations in order to reconfigure the network. I am trying to set up a WDS network with the two AE's (one being connected to the internet and the other serving as a remote to extend the range and use AirTunes function). When using Airport Utility and going through the setup process, I set up the primary AE with the connection to the internet. I am then using Airport Utility to try and configure the second AE to join the main network, but AU is not allowing the remote AE to connect/join the primary network. I keep getting an error message saying that the Apple wireless device could not join the WDS network and that I should close Airport Utility and try again. I have tried this a number of times, as well as performing more hard resets of both AE's and nothing seems to be working - any suggestions??
This is the first time I have ever had this problem using AU. In past versions of the program this has always worked setting up the network automatically, but does not seem to be working this time. Any suggestions would be helpful.
Thanks,
JB

You would get better responses if you posted in the airport section of the forum.
http://discussions.apple.com/category.jspa?categoryID=140

Problems setting up WDS with old AX and new AEBS

Hi all,
after buying a new AEBS last week, I want to put my old AX back into service. Here's what I have planned:
The cable modem sits in the living room near my stereo. The AX should connect to the cable modem and the stereo and be the main station in a WDS network with the AEBS. The AEBS will be in my study as a remote station to the AX.
Sounds trivial, but apparently it isn't I have spent the evening setting up the two base stations again and again. For some reason, the Airport Utility cannot see both stations at once as soon as they are configured. The AEBS won't find the AX even though the MAC address is correct.
I tried with and without WPA/WPA2, but I cannot figure out what's wrong
Could someone please give me a step by step guide of what to do? I am quite desperate by now...
Cheers from Switzerland
Daniel

Well, what can I say... Of course, I could not give up
Finally I got it to work. For future reference, here's how:
I first set up the AEBS to create a network, then used the Wizard of the Airport Utilitiy to add the AX as a WDS-device (it sets up the whole WDS automatically). Then I flipped the settings - set the AX to be main and the AEBS to be the remote.
I also had to adapt the Internet-Settings. Both base stations were set to bridge-mode, which doesn't work in my case because I only get two IPs from my ISP. So, I set the AX (the main) to share an internet connection and get its IP by DHCP. The AEBS on the other hand needed to get an IP manually (outside of the address space of the DHCP server created by the AX, but within its subnet).
After that it all worked - even AirTunes The AEBS now sits on my desk and the AX provides internet from the living room.
Cheers,
Daniel

Advised to get an "extender" to be able to stream netflix, etc. through new digital tv. Apple store told me to buy Airport Express and set up WDS. Upon reading about WDS it stated cannot set up WDS with Airport Express 802.11n,

I was advised I needed an "extender" to stream Netflix, etc. through my newly purchased digital TV. Apple store advised me to buy Airport Express and choose WDS setting. When reading instructions on how to set up WDS it states cannot set up WDS with an 802.11n airport express, which is what they told me to purchase. How do I set up this Airport Express to extend my internet signal from my modem & airport to be able to stream internet capability to my TV?

I was advised I needed an "extender" to stream Netflix, etc. through my newly purchased digital TV. Apple store advised me to buy Airport Express and choose WDS setting. When reading instructions on how to set up WDS it states cannot set up WDS with an 802.11n airport express, which is what they told me to purchase. How do I set up this Airport Express to extend my internet signal from my modem & airport to be able to stream internet capability to my TV?

Problems setting up WNA with OAS 10.1.2.0.2 and Windows 2008

Hi,
I am trying to set up WNA with an OAS 10.1.2.0.2 in a RHEL 4 platform. I have been able to configure Synchronization and Windows External Authentication following these steps:
http://download.oracle.com/docs/cd/B14099_19/idmanage.1012/b14085/odip_actdir003.htm#i1010999
I have also tried to configure WNA without success with those steps.
The scenario is here:
* OAS 10.1.2.0.2 infra in a RHEL 4
* Windows 2008 SP1 (only i use AD from it)
* Windows XP (client) that should be able to log in without problems when WNA is configured
How can make it work? I haven´t find any useful documentation
Thanks,
Max

Check these out:
http://www.freeoraclehelp.com/2011/09/oid-integration-with-ms-active.html
http://www.freeoraclehelp.com/2011/09/enable-ssl-for-oid-instance-of-oracle.html
http://www.freeoraclehelp.com/2011/09/oracle-password-filter-to-sync.html

Can I set up WDS with a 3rd party wireless router?

I have an Actiontec 802.11g wireless router that is working ok but the range is limited. I also have an airport express that I'm currently not using. Can I use the two together to set up a WDS to extend the range of the network? The discussions and Apple help seem to assume that the main base station is an Apple Extreme.
Any guidance and specific setup instructions would be appreciated.

Hi again kenkarno,
So the whole idea of WDS (Wireless Distribution System) is to enable you to use multiple devices (i.e. Wireless Routers) on the same network.
For example if you set up a wireless network called "kenkarno" but your original router wasn't powerful to cover the desired area, you could add further routers to the same "kenkarno" network as opposed to creating a multitude of networks for each router. The obvious advantage is that if you're out of range of one router you're in range of another without having to switch networks.
At the moment WDS is very proprietary (hence my first post) so it is common when trying to set up a WDS composed of different brand routers, you may not get them to talk to one another due to incompatibilities in their software.
In your case, it could be that your Actiontec router will not be able to form part of a WDS with your AE so your suggestion of using ethernet between the Actiontec and the AE could be the way to go here (although you'd have two separate networks). If you went for a second AE you could create a WDS between this and your existing one which may make life a little easier.
Hope it works out

Problem of black screen with MSI gtx570 twin frozr 3

I have a problem that will seriously hurt me...(gtx 570 twin frozer 3)
psu:680green
cpu:1055t oc
mb:ta 890 fxe
ram:crosair 4 gb 1600
my problem just in game with support dx11
dx9 very well and no problem
for example:
crysis 2 dx11
homefront dx11
bc 2 dx11
deus ex dx11
all game with support directx 11 and Only 5 seconds of the game comes out and starts again after a few seconds without any problems
Friends please help me to resolve my issue I think.
I do not know the English language well,sorry
Thanks to all.

Try increasing your core voltage using msi afterburner. My card personally is stable at 0.9750mv and some users are stable at 0.9880mv. Good luck mate!

Incompatibility Problem new Kingmax DDR400 with MSI-6585 Mo Bo

Recently just bought a new 256MB Kingmax DDR400 color module but found that it was incompatible with MSI-658(SiS648 chipset mo bo). It did works fine with the old model of Kingmax DDR400(Black chip module).However the code of the both modules are same. And I have tried configuration according to MSI and Kingmax.But found that even the just new single new DDR400 without mixing both also cannot work at frequency of 200Mhz.But the one old working fine. I exclude the possibilty of faulty of the new module cause I have tested it on other platform and do even exchange a new one from vendor.
I have emailed the Kingmax and MSI support, but none of them of reply my msg. Since it was in the category of certified module published in the MSI website, i think MSI and Kingmax will be very irresponsible for not yet test the new color module on the board.

Besides color, the old model and new model really different in term of the board. The height of new model is shorter than old one and very clearly even the layout of the chip is different. By SPD is also different.
I have tried different DIMM slot with different voltage different configuration. It is really a serious problem, but sadly still din receive any reply from MSI and Kingmax.

WDS compatibility, ABS Extreme & Motorola WR850G

Hello. Does anyone know if the WDS functionality in the ABS Extreme and the Motorola WR850G router are compatible? The Motorola WAP is the primary AP and I am trying to get the ABS Extreme to connect to it. So far my tries have been unsuccessful, but it may just be my settings combined with me not setting it up right. Since I've heard of WDS interoperability issues I thought I would see if anyone has done this with success.
Thanks!!!

The Motorola WR850G does not support Apple's flavor of a wireless distribution system (WDS).
The practical reality is that if you want to set up a WDS, you should have a main base station that is either (a) another Airport Extreme Base Station, (b) an Airport Express, or (c) a Linksys WRT54G or WRT54GS - one of the very few non-Apple wireless routers to support Apple's WDS implementation.

Problem setting up Wireless with WAP54G

I am having trouble setting up my wireless network with my WAP54G access point. I have used this same router successfully before but now on my new network it gives me trouble.
I did a reset on my Access Point, Then the default setting is with a static IP address. I can just connect with the access point (wireless) with no problem. But when connected to the modem it doesn't give me internet...
Reading the manual of the modem it tells me that any router connected to the modem should be set to DHCP. So when I put the settings on my access point to DHCP (and change them on the network settings of my laptop) I cannot connect with the Accesspoint anymore..
Can anyone help me? am I just doing something stupid here?

Hi sdedmer. What is the make and model of your modem? Is it a modem-router-in-one or a gateway? If so, you may need to enable the DHCP of the device so it can provide IP addresses for multiple devices to connect wirelessly. The WAG54G is an access point. It can only provide wireless and Internet access to one device at a time. For this, you may need to purchase a wireless router if you want to connect multiple devices (wired or wireless) and extend the wireless range using the WAG54G.
For more information about access points and routers, check this link out: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=b22772feb0f348f98a9c5d13e8469fca_192.xml&pid=80&re...
Information. Share it to learn.
Help, learn and share

Problems setting up Tomcat with RoboHelp Server V8

Hi,
My Systems Administrator is trying to set up RoboHelp Server version 8 for me. he has been following the Adobe Installation guide and has got as far as page 10 where it tells him to install and configure IIS and TomCat, at this point he says he does not understand what he should be doing. He has not installed TomCat before and it is telling him to configure the tomcat directory and although he has tried using what it says it comes up with an error the directory does not exist.
He is using:
Windows 2008 Server Standard
IIS 7.0
TomCat 6.0.20
SQL Server 2008 express SP1 - this is the latest version the adobe instructions says RooHelp Server works with SQL Server 2008 but does not mention express not sure if that could be a problem?
MS Report Viewer 2008 SP1
Java V6 Update 12
He says the installation guide talks about a directory with Win32 in it which does not appear on his machine its a 64 bit machine.
Please can someone give me some instructions on how to set up the TomCat part - I have looked but the troubleshooting that adobe has does not seem to be for Windows 2008 only Vista and XP and even then it says nothing about setting up TomCat
Thanks in advance
Erika

Erika
Not an area I can help with but try this post. http://forums.adobe.com/thread/204737?tstart=0
Also look through the forum. There are some detailed posts on this.
Finally take a look at http://notcolin.wordpress.com. There are some relevant blogs there.
See www.grainge.org for RoboHelp and Authoring tips

I am having problems setting up iCloud with Outlook 2007.

I was able to setup the email with Outlook, but every time I try to setup the contacts. I get the following error:
your setup could not be started because of unexpected error
This error does not occur immediately, but occurs after several steps of downloading and uploading.
If I hit the report button, it hangs. So I hit cancel after that in my retries. I am on Windows 2007 (32-bit).

You need to leave more information like what is the ios5 device. I following instructions accidently set up two iclouds and then I couldn't get the contacts in. My mobileme email isn't going to work anymore because I set up an icloud using my store apple ID. Apparently the term apple ID can refer to any apple product ID that you make up not the one you use in the store. So you need to leave more infor on what is your problem to figure out how to help.
GR

Problems setting Inhibit Outputs with UMI

I am using a 3rd party stepper drive with a PCI7334 and 7764 UMI. The Step, Dir and Enable inputs on the drive are opto isolated. I have tied the -ve terminal of each to Ground and the +ve terminal to +5V though a 390ohm resistor and to the corresponding connection on the UMI.
I setup the axes inhibit output in software to be Inverting, the switch on the UMI is set to Active Low inhibit outputs and the Drives are Active closed (need to have a potential difference across them to be enabled).
My third axis must be enabled the opposite way around. But when i set it up in software to be Non-inverting, it doesn't change on the UMI. why would this be so?
Can you have one axis with its inhibit output active low, and another axis with it
s inhibit output active high?
Also, Do i need to pull the inhibit outputs high?
Your help will be much appreciated.

To whom it may concern:
Yes, you can have one axis with its inhibit output active low and another axis set to active high. You need to go into MAX under the Device Settings and expand the tree entitled Axis Settings. With the corresponding axis selected in the tree, you can set the inhibit output to active high or low. If you don't expand the tree under Axis Settings then whatever you set the inhibit output polarity to will apply to all axes on the board. That might be part of your problem.
That inhibit output shouldn't need to be pulled high. That would be handled internally to the board.
Hopefully that is help to you. Best of luck with things.
Jim Laudie
Applications Engineer, National Instruments

Problem setting up connection with 2wire USB adapter (BT Home Network 1200)

I keep on running into a brick wall setting up my internet connection on my newly purchased MacBook (I have never used a mac before, having used a PC for years). I am trying to set up my macbook as an additional computer on my BT Home Network 1200, and I have installed the drivers given on the 2wire CD, but even when I plug in the USB adapter, the Macbook does not seem to recognise it. The adapter looks something like this:
Anyway, the instructions given in the BT Home Network PDF manual seem to suggest that it is relatively straightforward, and that it is simply a matter of clicking the apple menu, selecting "control panels", selecting "TCP/IP", and then in the "connect via" box, clicking on the pulldown menu and selecting 2Wire PC Port. However, I am using 10.4.9 and it seems to me that this guide must have been written for an outdated version of Mac OS X because none of these instructions seem to make sense or work in the context of my macbook. At the moment, it seems like I won't be able to get my macbook online. Could someone please help explain to me how to get around this?

Any reference to 'Control Panels' will, indeed, be for Mac OS 9.x, the last version of which (9.2) was released in 2001.
My advice would be to return it to BT and ask them for an ethernet-based modem, not a USB one.
USB DSL modems have varying levels of support in Mac OS X ranging from poor to none. The fact that 2Wire doesn't include Mac OS X instructions implies that this model is at the lower end of that scale.
By comparison, an ethernet-based modem will connect to your Mac via ethernet, have the option of sharing the connection with multiple machines, typically be faster, and has an almost 100% compatibility rate.

Problem setting file extension with jspc

I'm using xhtml which it appears the Jasper compiler (Tomcat 5.5) can't handle. It seems to only recognize files with the jsp and jspx extensions. Is there a way (either on the command line or via the Ant task) to set this? What is the proper way of pre-compiling these pages?
Thanks in advance.
Scott Czadzeck

Hi,
You can restrict them to save in any other format by making the check.
Simply add listner for the Event.OPEN on the fileReference and inside this check for your allowed extension,if the extension is not what you want then
simply right a line there like:-
fileReference.cancel();
And addtionally you can give any alert that your file should be of that particular extension.
with Regards,
Shardul

Problem setting up WDS with MSI RG54GS2 & Motorola WR850g

Similar Messages

Maybe you are looking for