Problem starting up G5 2.5 after installing 10.4.7

i have a G5 dual 2.5 (single core) that, until yesterday was running 10.3.9 and final cut pro 4.5 and working just fine.
yesterday i upgraded to 10.4.7 and fcp 5.1.1 (mid-project, which was soooooooo stupid, but that's another thing,) and now, whenever i restart or shut down and restart the computer, i just get the "chung" and nothing boots up. no desktop, no grey screen with spinning cursor. nothing. just a black screen. the only way to get it to restart is to shut down again, open up the side and reset the pmu.
i reset the permissions, etc through Onyx. no help.
i called apple and they think it might be a hardware issue and that i should take it in for repair. but repair is at least 10 days away and, like i said, i'm mid project and can't loose it right now. also, hardware related? why now, after installing new system software? wouldn't that be software related?
so, at any rate, now, instead of shutting my machine off at night, i'll just have to leave it on and suck up the juice until i can get it into the shop....
...unless any of you have experienced this and have an idea of what is wrong.
can anyone help??
thanks in advance
carl
if you need more info...hardware configs, etc, let me know.

so i ran hardware test yesterday and my machine failed the logic board test - twice. so bad motherboard?
took it to the apple store in jacksonville, and when they ran the hardware test it passed..everything. they ran it agin and it passed again. but when they reinstalled tiger, same restart and shutdown problem.
they said it could be the ram i installed a year ago...crucial, 2 512 sticks. and when we pulled them out and reinstalled tiger again, the machine seemed to be ok.
so they recommended i buy apple ram at $200 a gig! they said tiger is very sensitive to ram.
i don't understand. i know many ppl who do not use apple ram, and from what one of the genius' told me, the crucial ram i installed is the same apple uses anyway.
i don't want to spend another $200 on new ram to run tiger when the ram i have now runs fine in panther.
but i feel cheated that i have a fast machine, but can't run tiger or final cut studio on it becaue of my ram!?!?!
i don't know what to do at this point.
any thoughts or recommendations? I'm stuck...
oh, also, apple care on the phone failed to tell me that i qualified for on-site help instead of having to drive an hour to the apple store. i wonder if i run hardware test again and it fails, and i write down the error code, i can get apple care to send someone out to check the machine out from top to bottom. i spent over 4 hours at the apple store yesterday and i really don't want to go through that again!

Similar Messages

  • Will not start even in safe boot after installing latest camera update

    MacBook Pro will not start even in safe boot after installing latest camera update.
    I started my machine and did a software update. Only the camera update needed. So installed and when required I pressed restart. It restarted and did install. Then restarted again. I expected to get to the login screen and it turned itself off. Tried three more times. Each time shutting off. I unplugged everything, and pressed start waiting for log in window. No it shutdown before the log in window. I then tried safe mode and that did not work either on three more occasions.

    I have managed to resolve some issues. I can now restart the machine via a CD boot. If I do cmd C into something like tech tool pro, then restart from that disks menu it restarts every time.
    If I try a safe start it shuts down. If I try a normal start it shuts down. I have managed to repair permissions and that cleared up some start up permissions but with no improvement to the boot problem. The only way to load is via the cmd-C boot option. Any other ideas?

  • Ive just upgraded my late 2009 macbook, and things are not working properly. First of all, when I started the computer first time after installing Mountain Lion, some message advised me that some files were impossible to install.

    Ive just upgraded my late 2009 macbook, and things are not working properly. First of all, when I started the computer first time after installing Mountain Lion, some message advised me that some files were impossible to install. Once I wrote my password, and for now on, everytime I start the session, another window advise me that "Java SE 6" is missing, due that, the computer can't run some "CS5Service Manager". If I try to install it, the download ends with an error. If finally, you skip the istallation, you arrive to the dock, but the menu bar at the top of the screen doesn't show up.
    In addition, my trackpad doesn't works either. I can move the arrow but i can't click anywhere, probably because the option of clicking by touching is disabeled and I can't performance a regular click.
    I'll be very glad if someone know what the heck is happening with my computer. Anyway, I'm going to the genius bar next Saturday. Thx!

    We're sorry.
    We can't find the article you're looking for.
    Please return to the Apple Support homepage.
    Sigh.

  • Having many problem with wifi....after installing lion......

    Having many problem with wifi....after installing lion......it connect with wifi but not with Internet and at the same time iPad 2, iPhone 4 works smooth......help......I have MacBook air without thunderbolt and mac mini

    I had the same problem last night. Boot into OSX and reboot the router - fine. Boot into Windows and wrong. Here were my fixes:
    Firstly, I kept all the settings on my router solid. Just leave them as they are. Boot into OSX and check the Network settings and make a note of your IP address and the router's IP address.
    Second, boot into Windows, then open up your wireless connection settings and navigate through to the properties where you can set the IP address.
    Third: Set the IP address to your routers IP address changing the last set of digits to a value between 5 and 255 (I have 8 devices so I set the last two digits to 10.) This will keep the IP static.
    Tab through the Mask settings to default those.
    Then set the default gateway to your router's IP address.
    Check that the Network Adapter's setting has IPv6 disabled (uncheck the box)
    Finally: Set the primary DNS server to 8.8.8.8 then the secondary to 8.8.4.4 and then reboot the router.
    That's what got my connection running.

  • Problem : Instance info corrupt in SAPMMC after installing the license

    I have successfully installed the NW WAS 2004s preview edition and got the 3 month license key.
    However after installing the license, when I went to SAPMMC to re-start the system, the SAP Instace information seems to be messed up.
    Before installing the license, MMC was showing the SAP system as [Console Root\SAP Systems\NSP\w72c-7wpdl71 0] and now after the installation it has replaced the 7's in my systems name with #'s, so now it looks like
    [Console Root\SAP Systems\NSP\w#2c-#wpdl#1 0].
    SAP Management Console is completely unusable because of this. It keeps on giving 'Host not found' errors.
    Fortunately, everything else with the system seems to be working fine. At least so far !!
    - SLICENSE shows the new license.
    - SICK does not report any problems.
    So far I am forced to use the command prompt to stop and start the instace and the database. This works fine and I am able to start and stop the system.
    Any ideas what could have gone wrong ?
    Did it not like the '-' in my system name ?
    Anything wrong in windows registery ?
    Did I install the license incorrectly ?
    And how to fix this ?
    Any help will be greatly appriciated.
    Devendra
    To add more information,
    - I did not restart the system, even once, before installing the license.
    - After installing the system I just saw SAPMMC and checked all the nodes to see the syslog etc. and they were fine.
    - I might have changed some profile parameters after installing the license.
    Message was edited by: Devendra Shetye

    Hi,
    It worked for us too. we restarted the SAP servers from  the Administrative Tools-> Services panel.
    thanks a lot
    Padmaja Ragavendra
    PS: wanted to give you reward points but it is no tallowing me to
    padmaja
    Message was edited by: Padmaja Ragavendra

  • Firefox desktop and start menu shortcuts were hidden after install - why?

    Hi
    I just installed Firfox 5 and after installing both the desktop shortcut and the start menu shortcut were marked as hidden in windows.
    Anyone else experienced this and have any ideas what could have caused this. It was rather confusing.
    I'm running on a brand new laptop (Dell XPS-17) running Windows 7 Home Premium (64bit). The only candidate I can think of is the computer came with McAffee, which I haven't used in years. It was appallingly bad back then but thought I'd give it a chance as Dell gave me 15months free.
    Thanks
    Mog

    Hi,
    I would like to suggest you try these steps to figure out what could be causing this problem.
    1. Run Troubleshooter
    Open the Search and Indexing troubleshooter
    http://windows.microsoft.com/en-US/windows7/Open-the-Search-and-Indexing-troubleshooter
    2. Create a new library and include fewer folders for test purpose. Now search for a file from that folder. See if it works.
    Create a new library
    http://windows.microsoft.com/en-US/windows7/Create-a-new-library
    3. Try to rebuild search indexing. Refer the steps from the following article.
    http://windows.microsoft.com/en-US/windows7/Change-advanced-indexing-options
    Also you may use the System File Checker tool (SFC.exe) to check the issue. The sfc /scannow command scans all protected system files and replaces incorrect versions with correct Microsoft versions.
    How to use the System File Checker tool to troubleshoot missing or corrupted system files on Windows Vista or on Windows 7
    http://support.microsoft.com/kb/929833
    In addition, you may refer to the following Microsoft TechNet article for the Windows Search related Group Policies.
    Group Policy for Windows Search
    http://technet.microsoft.com/en-us/library/cc732491(WS.10).aspx
    Hope it helps.
    Regards,
    Blair Deng
    Blair Deng
    TechNet Community Support

  • Lion starts in 'set up' mode after installing Parallelsn safe mode

    Big problem.
    I couldn't get on with VMWare Fusion as it was piling up huge files (106 Gb) and using up half of my hard drive. I had always had problems with it since installation so i decided to take up the transfer offer from Parallels and installed that yesterday. The installation went like a dream, I installed Quickbooks (the only reason I use the PC facility - QB is not available for Mac in the UK) and everything went swimmingly. I recovered my my 106 Gb of space and was very happy.
    Then, on restarting the problems started and this is where I need help please.
    1. The Mac Pro (8Gb RAM, 250 Gb hard drive, 2 x 2.66 dual core Xeon) takes longer than before to shut down.
    2. On restart I get the startup sound quite quickly but then get a white screen for about 2 minutes.
    3. The Apple logo appears and shortly afterwards the spinning clock for about 20 spins.
    4. Another brighter white screen.
    5. Grey (Lion) screen appears but without the login password box and avatar. Instead I just get the  emergency start up box giving me the chance to re-install Lion, restore from Time Machine, disk utility etc.
    First time I tried disk utility to repair the main drive and this worked,  start up was OK although it took ages more than usual. Second and third time the restart just took me back again to the box mentioned above. Once again I repaired the disk using Disk Utility but this time it would not start again, I just got the same box. Only on the third attempt did it work and the Mac booted OK.
    So, what is causing this to happen and how can I repair it?

    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414

  • I am unable to start adobe photoshop lighthouse 5 after installing it.  (0xc000007b)

    After installing Adobe Photoshop Lighthouse 5 from a disk, I was unable to open it.  "This application was unable to start correctly, (0xc000007b)".  Any help with this?

    Could not open a scratch file because the file is locked or you do not have the necessary access privileges. (…) | Mylen…
    Mylenium

  • Opensso : problem load opensso admin console page after install agent

    Hi,
    After installing policy agent for Tomcat in another instance,
    I could not load opensso admin console as usual (http://opensso.local.asyd.net:8000/opensso/UI/Login). The message
    given:
    root cause
    javax.servlet.ServletException: Servlet execution threw an
    exception
         com.sun.identity.setup.AMSetupFilter.doFilter(AMSetupFilter.java:91)
    root cause
    java.lang.NoClassDefFoundError
         com.sun.identity.authentication.client.AuthClientUtils.<clinit>(AuthClientUtils.java:136)
    or
    com.sun.identity.authentication.UI.LoginServlet.initializeRequestContext(LoginServlet.java:106)
    The tomcat log gave this message:
    SEVERE: Servlet.service() for servlet LoginServlet threw exception
    java.lang.NoClassDefFoundError
         at com.sun.identity.authentication.UI.LoginServlet.initializeRequestContext(LoginServlet.java:106)
    +++++++++++++++++++++++++++++++++++++++++
    I have 2 Tomcat instances on one machine:
    /home/opensso/apache-tomcat-6.0.18 (where the open sso server is deployed)
    /opt/tomcat-instance/opensso.local.asyd.net (where the web server client is deployed and agent is installed)
    Here is the response summary of my agent installation:
    SUMMARY OF YOUR RESPONSES
    Tomcat Server Config Directory :
    /opt/tomcat-instance/opensso.local.asyd.net/conf
    OpenSSO server URL : http://opensso.local.asyd.net:8000/opensso
    $CATALINA_HOME environment variable :
    /home/opensso/apache-tomcat-6.0.18
    Tomcat global web.xml filter install : false
    Agent URL : http://opensso.local.asyd.net:8081/mini-agentsample
    Agent Profile name : AS9Agent
    Agent Profile Password file name :
    /opt/tomcat-instance/tomcat_v6_agent/tomcat6agentpw.txt
    Verify your settings above and decide from the choices below.
    1. Continue with Installation
    2. Back to the last interaction
    3. Start Over
    4. Exit
    Please make your selection [1]: 1
    Updating the /home/opensso/apache-tomcat-6.0.18/bin/setclasspath.sh
    script with the Agent classpath ...DONE.
    Creating directory layout and configuring Agent file for Agent_001
    instance ...DONE.
    Reading data from file
    /opt/tomcat-instance/tomcat_v6_agent/tomcat6agentpw.txt and
    encrypting it ...DONE.
    Generating audit log file name ...DONE.
    Creating tag swapped OpenSSOAgentBootstrap.properties file for instance
    Agent_001 ...DONE.
    Creating a backup for file
    /opt/tomcat-instance/opensso.local.asyd.net/conf/server.xml ...DONE.
    Creating a backup for file
    /opt/tomcat-instance/opensso.local.asyd.net/conf/web.xml ...DONE.
    Adding OpenSSO Tomcat Agent Realm to Server XML file :
    /opt/tomcat-instance/opensso.local.asyd.net/conf/server.xml ...DONE.
    Adding filter to Global deployment descriptor file :
    /opt/tomcat-instance/opensso.local.asyd.net/conf/web.xml ...DONE.
    Adding OpenSSO Tomcat Agent Filter and Form login authentication to
    selected Web applications ...DONE.
    SUMMARY OF AGENT INSTALLATION
    Agent instance name: Agent_001
    Agent Bootstrap file location:
    /opt/tomcat-instance/tomcat_v6_agent/Agent_001/config/OpenSSOAgentBootstrap.properties
    Agent Configuration file location
    /opt/tomcat-instance/tomcat_v6_agent/Agent_001/config/OpenSSOAgentConfiguration.properties
    Agent Audit directory location:
    /opt/tomcat-instance/tomcat_v6_agent/Agent_001/logs/audit
    Agent Debug directory location:
    /opt/tomcat-instance/tomcat_v6_agent/Agent_001/logs/debug
    Install log file location:
    /opt/tomcat-instance/tomcat_v6_agent/installer-logs/audit/install.log
    Thank you for using OpenSSO Policy Agent
    Edited by: enterprisecoder on Jun 27, 2010 8:19 PM
    Edited by: enterprisecoder on Jun 28, 2010 12:37 AM
    Edited by: enterprisecoder on Jun 28, 2010 2:14 AM
    Edited by: enterprisecoder on Jun 28, 2010 8:19 PM

    Hi
    I am facing the similar issue after installing the policy agent on tomcat 6.x
    Installation gets successfully, but once I start the tomcat server secured by agent than I get below error
    Dec 23, 2010 2:43:44 PM org.apache.catalina.core.AprLifecycleListener init
    INFO: Loaded APR based Apache Tomcat Native library 1.1.20.
    Dec 23, 2010 2:43:44 PM org.apache.catalina.core.AprLifecycleListener init
    INFO: APR capabilities: IPv6 [true], sendfile [true], accept filters [false], random [true].
    AgentConfiguration: Exception while reading new mod interval: "null"
    Dec 23, 2010 2:43:45 PM org.apache.tomcat.util.digester.Digester startElement
    SEVERE: Begin event threw error
    java.lang.ExceptionInInitializerError
    at com.sun.identity.agents.arch.Manager.<clinit>(Manager.java:643)
    at com.sun.identity.agents.tomcat.v6.AmTomcatRealm.<clinit>(AmTomcatRealm.java:64)
    at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
    at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
    at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
    at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
    at java.lang.Class.newInstance0(Class.java:355)
    at java.lang.Class.newInstance(Class.java:308)
    at org.apache.tomcat.util.digester.ObjectCreateRule.begin(ObjectCreateRule.java:206)
    at org.apache.tomcat.util.digester.Rule.begin(Rule.java:153)
    at org.apache.tomcat.util.digester.Digester.startElement(Digester.java:1356)
    at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.startElement(AbstractSAXParser.java:501)
    at com.sun.org.apache.xerces.internal.parsers.AbstractXMLDocumentParser.emptyElement(AbstractXMLDocumentParser.java:179)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanStartElement(XMLDocumentFragmentScannerImpl.java:1339)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.next(XMLDocumentFragmentScannerImpl.java:2747)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(XMLDocumentScannerImpl.java:648)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(XMLDocumentFragmentScannerImpl.java:510)
    at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:807)
    at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:737)
    at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:107)
    at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1205)
    at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:522)
    at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642)
    at org.apache.catalina.startup.Catalina.load(Catalina.java:510)
    at org.apache.catalina.startup.Catalina.load(Catalina.java:548)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
    at java.lang.reflect.Method.invoke(Method.java:597)
    at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261)
    at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413)
    Caused by: java.lang.RuntimeException: Unknown User Mapping Mode: null
    at com.sun.identity.agents.arch.AgentConfiguration.setUserMappingMode(AgentConfiguration.java:865)
    at com.sun.identity.agents.arch.AgentConfiguration.setHotSwappableConfigProps(AgentConfiguration.java:1170)
    at com.sun.identity.agents.arch.AgentConfiguration.initializeConfiguration(AgentConfiguration.java:1098)
    at com.sun.identity.agents.arch.AgentConfiguration.<clinit>(AgentConfiguration.java:1543)
    ... 31 more
    java.lang.reflect.InvocationTargetException
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
    at java.lang.reflect.Method.invoke(Method.java:597)
    at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261)
    at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413)
    Caused by: java.lang.ExceptionInInitializerError
    at com.sun.identity.agents.arch.Manager.<clinit>(Manager.java:643)
    at com.sun.identity.agents.tomcat.v6.AmTomcatRealm.<clinit>(AmTomcatRealm.java:64)
    at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
    at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
    at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
    at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
    at java.lang.Class.newInstance0(Class.java:355)
    at java.lang.Class.newInstance(Class.java:308)
    at org.apache.tomcat.util.digester.ObjectCreateRule.begin(ObjectCreateRule.java:206)
    at org.apache.tomcat.util.digester.Rule.begin(Rule.java:153)
    at org.apache.tomcat.util.digester.Digester.startElement(Digester.java:1356)
    at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.startElement(AbstractSAXParser.java:501)
    at com.sun.org.apache.xerces.internal.parsers.AbstractXMLDocumentParser.emptyElement(AbstractXMLDocumentParser.java:179)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanStartElement(XMLDocumentFragmentScannerImpl.java:1339)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.next(XMLDocumentFragmentScannerImpl.java:2747)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(XMLDocumentScannerImpl.java:648)
    at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(XMLDocumentFragmentScannerImpl.java:510)
    at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:807)
    at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:737)
    at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:107)
    at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1205)
    at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:522)
    at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642)
    at org.apache.catalina.startup.Catalina.load(Catalina.java:510)
    at org.apache.catalina.startup.Catalina.load(Catalina.java:548)
    ... 6 more
    Caused by: java.lang.RuntimeException: Unknown User Mapping Mode: null
    at com.sun.identity.agents.arch.AgentConfiguration.setUserMappingMode(AgentConfiguration.java:865)
    at com.sun.identity.agents.arch.AgentConfiguration.setHotSwappableConfigProps(AgentConfiguration.java:1170)
    at com.sun.identity.agents.arch.AgentConfiguration.initializeConfiguration(AgentConfiguration.java:1098)
    at com.sun.identity.agents.arch.AgentConfiguration.<clinit>(AgentConfiguration.java:1543)
    ... 31 more
    Exception in thread "SystemTimer" java.lang.NoClassDefFoundError: Could not initialize class com.sun.identity.agents.arch.AgentConfiguration
    at com.sun.identity.agents.arch.AgentConfiguration$ConfigurationMonitor.getRunPeriod(AgentConfiguration.java:1397)
    at com.sun.identity.common.TimerPool$WorkerThread.run(TimerPool.java:504)

  • Problem with system Inactivity/Idle time after installing Lion.

    Since installing Lion strange things have been happening.
    While I was happily editing a text file in TextMate and interacting with the Terminal, my screen saver started. I could only get rid of it by clicking on it, keyboard interaction didn't seem to clear it.
    Adium was sending lots of updates to MSN to try and update my friendly name, which was causing issues with MSN sending errors back.
    After unlocking 1Password and starting to look for a username/password the application would then lock itself.
    I have since disabled my screen saver, which has not appeared again. I have updated the preferences in Adium to not change my status based on system idle time, although the dock icon for it permanently displayed the Idle sign. I have also updated the preferences in 1Password to prevent auto-lock after n minutes.
    Since changing these preferences I have not had any problems with the applications, however this isn't ideal. As soon as I revert these changes my problems come back.
    Has anyone else had this sort of issue? Does anyone know what might be causing my system to believe that it is idle, when I am clearly interacting with it?

    If I delete the existing xml file and set the file path to the desktop, the script works again. However it doesn't work if the applescript is called by another program. This seems to indicate that the XML portion if fine, but that there is some sort of new file permission level control in applescript that wasn't there before that is preventing me from viewing the file. Any further ideas?
    Cheers

  • Problems opening mail and address book after install

    Ok I just reinstalled Leopard (erase and install after making backup with superduper).
    When I open Mail I get the message:
    +Mail can’t open because its index is read-only.+
    +This file is located in Michael MBP:Users:Michael:Library:Mail:Envelope Index. If this file is on your computer, use the Get Info panel in the Finder to change your permissions for this file to “Read & Write.” If this file is located on a network server, contact the server administrator. After your permissions are changed, open Mail again.+
    ok so when i go to that "envelope index" file it is about 6.3mb, when i check permissions, system and everyone are already read & write, there is also an (unknown) option that says read only but won't let me change it. if i move the "envelope index" file to the desktop and try to open mail, it creates a new envelope index file, but one that is way smaller, like 220k, and then nothing happens at all, mail just sits there, and i have to force quit it.
    also when i try to open address book, it bounces on the dock for a second, then closes.
    please help! i have to install on 2 more macs still

    I've had the same problem. There are usually two or three envelope index files (envelope index; envelope index-1; envelope index-2, etc.). Envelope index-1 is always the one that has me, as the user, as read/write. I trash the other files and open Mail again. It then tells me that it has to import mailbox and that usually takes two to three minutes. Sometimes it then opens, but often it will say headers are damaged and to quit and re-open. It imports the mailbox again and stays open until I have to close or restart and then we start the process all over again. I've tried repair permissions, but no help. Very annoying.
    Message was edited by: desulliv

  • Problem with black screen and crashes after installing windows 7 and bootcamp

    K, so I partitioned my internal HD using Bootcamp, installed a new copy of Windows 7 Home, put in my Mac OSX disk and installed the additional stuff. I can successfully log in to Windows and open the browsers I have installed: Comodo dragon and Mozilla FF. McAfee auto installed with FF and I have Comodo Antivirus installed.
    However, within minutes of use, my screen goes black, the computer does not shut down and reboot, I have to press the power button and wait a few secs for it to shut down then reboot. This has happened from both browsers while in Windows on Facebook in a game; while trying to save an attachment from an email via webmail and also while checking the inbuilt Windows settings for the display.
    The latter produced the following report (below) on reboot and when I hit the "look for a solution" button, the actual window vanished after a few secs.
    2 additional bits of info which may or may not be related:
    a) running windows troubleshooter I discovered I have prob with:
    driver for Inter (r) 5 series /3400 series chipset Family USB Universal Host Contoller - 3B3B
    - I Googled this and it seems a common prob. Tried the reinstall, didn't work, so disabled it as suggested on some of the forum posts.
    b) The OSX side of my computer seems to run fine most of the time, tho I have had the odd back screen, then wait, press reboot to power on and off in past as related in this post last month: https://discussions.apple.com/thread/4844797 (maybe a kernal panic..???)
    Would anyone know what is causing these probs or what I can do about them? My computer is no longer under warranty and the couple of times I had probs while it was, I was told the probs were to do with the power supply and given a new one, I'm not sure if they looked at the logic board. The OSX side has also had an ongoing prob to do with sudden shrinkage of the image content, which I mentioned to the geniuses at the Apple store b4, but as it wasn't acting up there they couldn't do anything about it... ( looks as tho sm1 changed the screen resolution and whatever is in the browser window shrinks, tho desktop, is never effected - if that makes sense!.) 
    All in all tho, does make me wonder if the prob is based in the graphics switching..???
    Problem signature:
      Problem Event Name:    BlueScreen
      OS Version:    6.1.7601.2.1.0.768.3
      Locale ID:    2057 Additional information about the problem:
      BCCode:    333
      BCP1:    0000000000000001
      BCP2:    0000000000000002
      BCP3:    0000000000000003
      BCP4:    0000000000000004
      OS Version:    6_1_7601
      Service Pack:    1_0
      Product:    768_1 Files that help describe the problem:
      C:\Windows\Minidump\032413-20872-01.dmp
      C:\Users\KittyH\AppData\Local\Temp\WER-166952-0.sysdata.xml Read our privacy statement online:
      http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline:
      C:\Windows\system32\en-US\erofflps.txt 

    When booting up hold down the option key and pick the Mac startup disk.  To make it automatic, once in your Mac side go to preferences, startup disk and pick the Mac disk.  Next time you boot up it will boot up to Mac OS.

  • Problem with Exchange 2010 Public Folders after installing Exchange 2013 in my environment.

    I currently have an Exchange 2010 server with all the roles installed.  Before installing Exchange 2013, I was able to launch the Public Folder Management Console but now I get an error.  When I installed Exchange 2013, I got an error saying I
    had a instance of Exchange 2000 or Exchange 2003, but I didn't have any of these servers left.  There was still something in AD referencing my old server. I went into ADSIedit and deleted an old administrative group.  This deletion caused my access
    to my public folders to get messed up.  I followed this article, http://blog.bruteforcetech.com/archives/766, and I was able to gain access back in my outlook client but I still can't see the public folders in OWA.  I also get this error when
    trying to access either Default or System Public Folders.  "Cannot complete the operation because there isn't an available public folder database on server 'ExchangeServer'. It was running the command 'get-publicfolder - getchildren -identity '\'
    -server 'ExchangeServer' "
    My Public Folder Database exists and is mounted.  Any help is appreciated.

    Hi Belinda,
    Thank you for responding.  Yes you do understand my problem correctly.  One correction is that after deleting this entry in ADSIEdit, we couldn't access public folders at all either in Outlook or OWA.  I followed these steps in the below article:
     http://blog.bruteforcetech.com/archives/766
    After following these steps and recreating the entry on FolderHieachies in ADSI edit, I was able to gain access to the public folders again through Outlook, but still can't see them in OWA and can't access them in Public Folder Management Console.
    Here are the results to your requests:
    et-PublicFolder -Recurse | Format-List Name
    Name : IPM_SUBTREE
    Can't get the public folder database using legacy distinguished name '/O=HEROIX CORPORATION/OU=EXCHANGE ADMINISTRAT
    GROUP (FYDIBOHF23SPDLT)/CN=CONFIGURATION/CN=SERVERS/CN=EXCHANGE2010/CN=MICROSOFT PUBLIC MDB'.
        + CategoryInfo          : NotSpecified: (:) [Get-PublicFolder], TaskInvalidOperationException
        + FullyQualifiedErrorId : B546E0B0,Microsoft.Exchange.Management.MapiTasks.GetPublicFolder
    [PS] C:\Windows\system32>Get-PublicFolder -Identity \NON_IPM_SUBTREE -Recurse | Format-List Name
    Name : NON_IPM_SUBTREE
    Name : EFORMS REGISTRY
    Can't get the public folder database using legacy distinguished name '/O=HEROIX CORPORATION/OU=EXCHANGE ADMINISTRATIVE
    GROUP (FYDIBOHF23SPDLT)/CN=CONFIGURATION/CN=SERVERS/CN=EXCHANGE2010/CN=MICROSOFT PUBLIC MDB'.
        + CategoryInfo          : NotSpecified: (:) [Get-PublicFolder], TaskInvalidOperationException
        + FullyQualifiedErrorId : B546E0B0,Microsoft.Exchange.Management.MapiTasks.GetPublicFolder
    Also the msExchOwningPFTree attribute should be correct because this was edited with the correct value when I followed the instructions in the above article:
    CN=Public Folders,CN=Folder Hierarchies,CN=Exchange Administrative Group (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=Heroix Corporation,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=hero,DC=net

  • Problems with opening links in outlook after installing Flash player 11

    I recently installed a flash plaer 11 active X update. I wasn't given the option of not installing google chrome and another program - Ask toolbar I think ( or I may have missed it ) but when I discovered the problem I uninstalled the google chrome and the other program.
    After doing this I discovered that when I went to open links in outlook I received the message:
    ``This operation has been cancelled due to restrictions in effect on this computer. Please contact your system administrator.``
    I am running Windows 7 64 bit and using IE 9.
    Any help would be appreciated to return my system to normal.
    I also noticed that chrome and the other program were installed without automatically creating a restore point.
    I am very disappointed in how Adobe pushes programs on people.

    vals1979 wrote:
    I wasn't given the option of not installing google chrome
    How did you install the update - via website?  If so, you can always uncheck any optional software
    Either way, Chrome behaves very badly - especially when uninstalled.  Try setting your usual browser as the default browser, and Outlook, Word, etc. should open links normally after that.
    P.S. I do not endorse Adobe's policy to push optional software with their free products, but there is nothing we can do about that.  However, Adobe would not go as far as pushing spyware (Ask toolbar); most likely it was the harmless Google toolbar.

  • Problems Starting Weblogic  Server for Tutorials (Fresh install)...

    Hi guys, need a little help here.
    I'm trying to startup Weblogic Server for Java Control Tutorial application and I get all sorts of errors, mostly seeming to deal with JMS/JNDI network stuff. Here's the error dump I get:
    * To start WebLogic Server, use a username and *
    * password assigned to an admin-level user. For *
    * server administration, use the WebLogic Server *
    * console at http:\\hostname:port\console *
    starting weblogic with Java version:
    java version "1.4.2_05"
    Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_05-b04)
    Java HotSpot(TM) Client VM (build 1.4.2_05-b04, mixed mode)
    Starting WLS with line:
    C:\bea\JDK142~1\bin\java -client -Xdebug -Xnoagent -Xrunjdwp:transport=dt_socket
    ,address=8453,server=y,suspend=n -Djava.compiler=NONE -Xms256m -Xmx256m -XX:Com
    pileThreshold=8000 -XX:PermSize=32m -XX:MaxPermSize=128m -Xverify:none -ea -da
    :com.bea... -da:javelin... -da:weblogic... -Dplatform.home=C:\bea\WEBLOG~1 -Dwls
    .home=C:\bea\WEBLOG~1\server -Dwli.home=C:\bea\WEBLOG~1\integration -Dlog4j.con
    figuration=file:C:\bea\WEBLOG~1\common\lib\workshopLogCfg.xml -Dweblogic.managem
    ent.discover=true -Dweblogic.ProductionModeEnabled= -Dweblogic.security.SSL.ign
    oreHostnameVerify=false -Dwlw.iterativeDev=true -Dwlw.testConsole=true -Dwlw.log
    ErrorsToConsole=true -Dweblogic.Name=cgServer -Djava.security.policy=C:\bea\WEBL
    OG~1\server\lib\weblogic.policy weblogic.Server
    <Oct 30, 2005 2:33:31 PM PST> <Info> <WebLogicServer> <BEA-000377> <Starting Web
    Logic Server with Java HotSpot(TM) Client VM Version 1.4.2_05-b04 from Sun Micro
    systems Inc.>
    <Oct 30, 2005 2:33:31 PM PST> <Info> <Configuration Management> <BEA-150016> <Th
    is server is being started as the administration server.>
    <Oct 30, 2005 2:33:31 PM PST> <Info> <Management> <BEA-141107> <Version: WebLogi
    c Server 8.1 SP4 Mon Nov 29 16:21:29 PST 2004 471647
    WebLogic XMLX Module 8.1 SP4 Mon Nov 29 16:21:29 PST 2004 471647
    WebLogic Server 8.1 SP4 Mon Nov 29 16:21:29 PST 2004 471647
    WebLogic Server 8.1 SP4 Mon Nov 29 16:21:29 PST 2004 471647
    WebLogic Integration 8.1 SP4 Tue Nov 30 10:34:16 PST 2004 471877>
    <Oct 30, 2005 2:33:32 PM PST> <Notice> <Management> <BEA-140005> <Loading domain
    configuration from configuration repository at C:\bea\WEBLOG~1\samples\domains\
    workshop\.\config.xml.>
    <Oct 30, 2005 2:33:33 PM PST> <Notice> <Log Management> <BEA-170019> <The server
    log file C:\bea\weblogic81\samples\domains\workshop\cgServer\cgServer.log is op
    ened. All server side log events will be written to this file.>
    <Oct 30, 2005 2:33:34 PM PST> <Notice> <Security> <BEA-090082> <Security initial
    izing using security realm myrealm.>
    <Oct 30, 2005 2:33:34 PM PST> <Notice> <WebLogicServer> <BEA-000327> <Starting W
    ebLogic Admin Server "cgServer" for domain "workshop">
    <Oct 30, 2005 2:33:38 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgJMSPool-nonXA": SQL-server rejected establ
    ishment of SQL-connection. Pointbase Server may not be running on localhost at p
    ort 9093.>
    <Oct 30, 2005 2:33:40 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgJMSPool-nonXA": SQL-server rejected establ
    ishment of SQL-connection. Pointbase Server may not be running on localhost at p
    ort 9093.>
    <Oct 30, 2005 2:33:42 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgJMSPool-nonXA": SQL-server rejected establ
    ishment of SQL-connection. Pointbase Server may not be running on localhost at p
    ort 9093.>
    <Oct 30, 2005 2:33:44 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgJMSPool-nonXA": SQL-server rejected establ
    ishment of SQL-connection. Pointbase Server may not be running on localhost at p
    ort 9093.>
    <Oct 30, 2005 2:33:46 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgJMSPool-nonXA": SQL-server rejected establ
    ishment of SQL-connection. Pointbase Server may not be running on localhost at p
    ort 9093.>
    <Oct 30, 2005 2:33:47 PM PST> <Error> <JDBC> <BEA-001150> <Connection Pool "cgJM
    SPool-nonXA" deployment failed with the following error: 0:Could not create pool
    connection. The DBMS driver exception was: SQL-server rejected establishment of
    SQL-connection. Pointbase Server may not be running on localhost at port 9093..
    >
    <Oct 30, 2005 2:33:48 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgPool": SQL-server rejected establishment o
    f SQL-connection. Pointbase Server may not be running on localhost at port 9093.
    >
    <Oct 30, 2005 2:33:50 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgPool": SQL-server rejected establishment o
    f SQL-connection. Pointbase Server may not be running on localhost at port 9093.
    >
    <Oct 30, 2005 2:33:52 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgPool": SQL-server rejected establishment o
    f SQL-connection. Pointbase Server may not be running on localhost at port 9093.
    >
    <Oct 30, 2005 2:33:54 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgPool": SQL-server rejected establishment o
    f SQL-connection. Pointbase Server may not be running on localhost at port 9093.
    >
    <Oct 30, 2005 2:33:56 PM PST> <Warning> <JDBC> <BEA-001129> <Received exception
    while creating connection for pool "cgPool": SQL-server rejected establishment o
    f SQL-connection. Pointbase Server may not be running on localhost at port 9093.
    >
    <Oct 30, 2005 2:33:57 PM PST> <Error> <JDBC> <BEA-001150> <Connection Pool "cgPo
    ol" deployment failed with the following error: 0:Could not create pool connecti
    on. The DBMS driver exception was: SQL-server rejected establishment of SQL-conn
    ection. Pointbase Server may not be running on localhost at port 9093..>
    <Oct 30, 2005 2:33:57 PM PST> <Error> <JDBC> <BEA-001151> <Data Source "cgDataSo
    urce" deployment failed with the following error: DataSource(cgDataSource;cgSamp
    leDataSource) can't be created with non-existent Pool (connection or multi) (cgP
    ool).>
    <Oct 30, 2005 2:33:57 PM PST> <Error> <JDBC> <BEA-001151> <Data Source "cgDataSo
    urce-nonXA" deployment failed with the following error: DataSource(cgDataSource-
    nonXA;weblogic.jdbc.jts.ebusinessPool) can't be created with non-existent Pool (
    connection or multi) (cgJMSPool-nonXA).>
    <Oct 30, 2005 2:33:57 PM PST> <Alert> <JMS> <BEA-040052> <JMSServer "cgJMSServer
    " store failed to open java.io.IOException: JMS JDBC store, connection pool = <c
    gJMSPool-nonXA>, prefix = <weblogic>: connection pool does not exist.
    java.io.IOException: JMS JDBC store, connection pool = <cgJMSPool-nonXA>, prefix
    = <weblogic>: connection pool does not exist
    at weblogic.jms.store.JDBCIOStream.throwIOException(JDBCIOStream.java:48
    8)
    at weblogic.jms.store.JDBCIOStream.checkPool(JDBCIOStream.java:1599)
    at weblogic.jms.store.JDBCIOStream.open(JDBCIOStream.java:548)
    at weblogic.jms.store.JMSStore.open(JMSStore.java:224)
    at weblogic.jms.backend.BEStore.open(BEStore.java:262)
    at weblogic.jms.backend.BEStore.start(BEStore.java:151)
    at weblogic.jms.backend.BackEnd.openStores(BackEnd.java:1171)
    at weblogic.jms.backend.BackEnd.resume(BackEnd.java:1290)
    at weblogic.jms.JMSService.addJMSServer(JMSService.java:2260)
    at weblogic.jms.JMSService.addDeployment(JMSService.java:2031)
    at weblogic.management.mbeans.custom.DeploymentTarget.addDeployment(Depl
    oymentTarget.java:337)
    at weblogic.management.mbeans.custom.DeploymentTarget.addDeployments(Dep
    loymentTarget.java:597)
    at weblogic.management.mbeans.custom.DeploymentTarget.updateServerDeploy
    ments(DeploymentTarget.java:575)
    at weblogic.management.mbeans.custom.DeploymentTarget.updateDeployments(
    DeploymentTarget.java:241)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
    java:39)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
    sorImpl.java:25)
    at java.lang.reflect.Method.invoke(Method.java:324)
    at weblogic.management.internal.DynamicMBeanImpl.invokeLocally(DynamicMB
    eanImpl.java:754)
    at weblogic.management.internal.DynamicMBeanImpl.invoke(DynamicMBeanImpl
    .java:733)
    at weblogic.management.internal.ConfigurationMBeanImpl.invoke(Configurat
    ionMBeanImpl.java:509)
    at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:15
    60)
    at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:15
    28)
    at weblogic.management.internal.RemoteMBeanServerImpl.private_invoke(Rem
    oteMBeanServerImpl.java:988)
    at weblogic.management.internal.RemoteMBeanServerImpl.invoke(RemoteMBean
    ServerImpl.java:946)
    at weblogic.management.internal.MBeanProxy.invoke(MBeanProxy.java:954)
    at weblogic.management.internal.MBeanProxy.invokeForCachingStub(MBeanPro
    xy.java:481)
    at weblogic.management.configuration.ServerMBean_Stub.updateDeployments(
    ServerMBean_Stub.java:7691)
    at weblogic.management.deploy.slave.SlaveDeployer.updateServerDeployment
    s(SlaveDeployer.java:1304)
    at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.j
    ava:347)
    at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resum
    e(DeploymentManagerServerLifeCycleImpl.java:229)
    at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
    at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:966)
    at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
    at weblogic.Server.main(Server.java:32)
    >
    <Oct 30, 2005 2:33:57 PM PST> <Error> <JMS> <BEA-040123> <Failed to start JMS Se
    rver "cgJMSServer" due to weblogic.jms.common.JMSException: JMS can not open sto
    re cgJMSStore.
    weblogic.jms.common.JMSException: JMS can not open store cgJMSStore
    at weblogic.jms.backend.BEStore.start(BEStore.java:163)
    at weblogic.jms.backend.BackEnd.openStores(BackEnd.java:1171)
    at weblogic.jms.backend.BackEnd.resume(BackEnd.java:1290)
    at weblogic.jms.JMSService.addJMSServer(JMSService.java:2260)
    at weblogic.jms.JMSService.addDeployment(JMSService.java:2031)
    at weblogic.management.mbeans.custom.DeploymentTarget.addDeployment(Depl
    oymentTarget.java:337)
    at weblogic.management.mbeans.custom.DeploymentTarget.addDeployments(Dep
    loymentTarget.java:597)
    at weblogic.management.mbeans.custom.DeploymentTarget.updateServerDeploy
    ments(DeploymentTarget.java:575)
    at weblogic.management.mbeans.custom.DeploymentTarget.updateDeployments(
    DeploymentTarget.java:241)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
    java:39)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
    sorImpl.java:25)
    at java.lang.reflect.Method.invoke(Method.java:324)
    at weblogic.management.internal.DynamicMBeanImpl.invokeLocally(DynamicMB
    eanImpl.java:754)
    at weblogic.management.internal.DynamicMBeanImpl.invoke(DynamicMBeanImpl
    .java:733)
    at weblogic.management.internal.ConfigurationMBeanImpl.invoke(Configurat
    ionMBeanImpl.java:509)
    at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:15
    60)
    at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:15
    28)
    at weblogic.management.internal.RemoteMBeanServerImpl.private_invoke(Rem
    oteMBeanServerImpl.java:988)
    at weblogic.management.internal.RemoteMBeanServerImpl.invoke(RemoteMBean
    ServerImpl.java:946)
    at weblogic.management.internal.MBeanProxy.invoke(MBeanProxy.java:954)
    at weblogic.management.internal.MBeanProxy.invokeForCachingStub(MBeanPro
    xy.java:481)
    at weblogic.management.configuration.ServerMBean_Stub.updateDeployments(
    ServerMBean_Stub.java:7691)
    at weblogic.management.deploy.slave.SlaveDeployer.updateServerDeployment
    s(SlaveDeployer.java:1304)
    at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.j
    ava:347)
    at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resum
    e(DeploymentManagerServerLifeCycleImpl.java:229)
    at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
    at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:966)
    at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
    at weblogic.Server.main(Server.java:32)
    Caused by: java.io.IOException: JMS JDBC store, connection pool = <cgJMSPool-non
    XA>, prefix = <weblogic>: connection pool does not exist
    at weblogic.jms.store.JDBCIOStream.throwIOException(JDBCIOStream.java:48
    8)
    at weblogic.jms.store.JDBCIOStream.checkPool(JDBCIOStream.java:1599)
    at weblogic.jms.store.JDBCIOStream.open(JDBCIOStream.java:548)
    at weblogic.jms.store.JMSStore.open(JMSStore.java:224)
    at weblogic.jms.backend.BEStore.open(BEStore.java:262)
    at weblogic.jms.backend.BEStore.start(BEStore.java:151)
    ... 29 more
    >
    <Oct 30, 2005 2:33:57 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: CreditScoreTutorial is unable to connect to the JMS destination: tutorial.cr
    edit.request.topic. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: tutorial.credit.request.topi
    c could not be found. Please ensure that the JNDI name in the weblogic-ejb-jar.x
    ml is correct, and the JMS destination has been deployed.>
    <Oct 30, 2005 2:33:58 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: KNEX.bean.QueueTransport is unable to connect to the JMS destination: jws.qu
    eue. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: jws.queue could not be found
    . Please ensure that the JNDI name in the weblogic-ejb-jar.xml is correct, and t
    he JMS destination has been deployed.>
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <Security> <BEA-090170> <Loading the priv
    ate key stored under the alias DemoIdentity from the jks keystore file C:\bea\we
    blogic81\server\lib\DemoIdentity.jks.>
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <Security> <BEA-090171> <Loading the iden
    tity certificate stored under the alias DemoIdentity from the jks keystore file
    C:\bea\weblogic81\server\lib\DemoIdentity.jks.>
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <Security> <BEA-090169> <Loading trusted
    certificates from the jks keystore file C:\bea\weblogic81\server\lib\DemoTrust.j
    ks.>
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <Security> <BEA-090169> <Loading trusted
    certificates from the jks keystore file C:\bea\JDK142~1\jre\lib\security\cacerts
    .>
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <WebLogicServer> <BEA-000331> <Started We
    bLogic Admin Server "cgServer" for domain "workshop" running in Development Mode
    >
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <WebLogicServer> <BEA-000360> <Server sta
    rted in RUNNING mode>
    <Oct 30, 2005 2:33:58 PM PST> <Warning> <WebLogicServer> <BEA-000372> <HostName:
    0.0.0.0, maps to multiple IP addresses:192.168.0.1,70.34.104.139>
    <Oct 30, 2005 2:33:58 PM PST> <Warning> <WebLogicServer> <BEA-000372> <HostName:
    0.0.0.0, maps to multiple IP addresses:192.168.0.1,70.34.104.139>
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <WebLogicServer> <BEA-000355> <Thread "Li
    stenThread.Default" listening on port 7001, ip address *.*>
    <Oct 30, 2005 2:33:58 PM PST> <Notice> <WebLogicServer> <BEA-000355> <Thread "SS
    LListenThread.Default" listening on port 7002, ip address *.*>
    <Oct 30, 2005 2:34:07 PM PST> <Warning> <EJB> <BEA-010096> <The Message-Driven E
    JB: CreditScoreTutorial is unable to connect to the JMS destination: tutorial.cr
    edit.request.topic. Connection failed after 2 attempts. The MDB will attempt to
    reconnect every 10 seconds. This log message will repeat every 600 seconds until
    the condition clears.>
    <Oct 30, 2005 2:34:07 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: CreditScoreTutorial is unable to connect to the JMS destination: tutorial.cr
    edit.request.topic. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: tutorial.credit.request.topi
    c could not be found. Please ensure that the JNDI name in the weblogic-ejb-jar.x
    ml is correct, and the JMS destination has been deployed.>
    <Oct 30, 2005 2:34:08 PM PST> <Warning> <EJB> <BEA-010096> <The Message-Driven E
    JB: KNEX.bean.QueueTransport is unable to connect to the JMS destination: jws.qu
    eue. Connection failed after 2 attempts. The MDB will attempt to reconnect every
    10 seconds. This log message will repeat every 600 seconds until the condition
    clears.>
    <Oct 30, 2005 2:34:08 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: KNEX.bean.QueueTransport is unable to connect to the JMS destination: jws.qu
    eue. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: jws.queue could not be found
    . Please ensure that the JNDI name in the weblogic-ejb-jar.xml is correct, and t
    he JMS destination has been deployed.>
    <Oct 30, 2005 2:44:08 PM PST> <Warning> <EJB> <BEA-010096> <The Message-Driven E
    JB: KNEX.bean.QueueTransport is unable to connect to the JMS destination: jws.qu
    eue. Connection failed after 62 attempts. The MDB will attempt to reconnect ever
    y 10 seconds. This log message will repeat every 600 seconds until the condition
    clears.>
    <Oct 30, 2005 2:44:08 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: KNEX.bean.QueueTransport is unable to connect to the JMS destination: jws.qu
    eue. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: jws.queue could not be found
    . Please ensure that the JNDI name in the weblogic-ejb-jar.xml is correct, and t
    he JMS destination has been deployed.>
    <Oct 30, 2005 2:44:17 PM PST> <Warning> <EJB> <BEA-010096> <The Message-Driven E
    JB: CreditScoreTutorial is unable to connect to the JMS destination: tutorial.cr
    edit.request.topic. Connection failed after 63 attempts. The MDB will attempt to
    reconnect every 10 seconds. This log message will repeat every 600 seconds unti
    l the condition clears.>
    <Oct 30, 2005 2:44:17 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: CreditScoreTutorial is unable to connect to the JMS destination: tutorial.cr
    edit.request.topic. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: tutorial.credit.request.topi
    c could not be found. Please ensure that the JNDI name in the weblogic-ejb-jar.x
    ml is correct, and the JMS destination has been deployed.>
    <Oct 30, 2005 2:54:08 PM PST> <Warning> <EJB> <BEA-010096> <The Message-Driven E
    JB: KNEX.bean.QueueTransport is unable to connect to the JMS destination: jws.qu
    eue. Connection failed after 122 attempts. The MDB will attempt to reconnect eve
    ry 10 seconds. This log message will repeat every 600 seconds until the conditio
    n clears.>
    <Oct 30, 2005 2:54:08 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: KNEX.bean.QueueTransport is unable to connect to the JMS destination: jws.qu
    eue. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: jws.queue could not be found
    . Please ensure that the JNDI name in the weblogic-ejb-jar.xml is correct, and t
    he JMS destination has been deployed.>
    <Oct 30, 2005 2:54:17 PM PST> <Warning> <EJB> <BEA-010096> <The Message-Driven E
    JB: CreditScoreTutorial is unable to connect to the JMS destination: tutorial.cr
    edit.request.topic. Connection failed after 123 attempts. The MDB will attempt t
    o reconnect every 10 seconds. This log message will repeat every 600 seconds unt
    il the condition clears.>
    <Oct 30, 2005 2:54:17 PM PST> <Warning> <EJB> <BEA-010061> <The Message-Driven E
    JB: CreditScoreTutorial is unable to connect to the JMS destination: tutorial.cr
    edit.request.topic. The Error was:
    [EJB:011010]The JMS destination with the JNDI name: tutorial.credit.request.topi
    c could not be found. Please ensure that the JNDI name in the weblogic-ejb-jar.x
    ml is correct, and the JMS destination has been deployed.>
    THANK YOU for any help you can provide!

    These are errors/warning because of incorrect connection pool settings.Either the database parameters were not configured correctly or there were some issues with the configuration itself.
    Your server did start up correctly though.
    "<Server started in RUNNING mode>"

Maybe you are looking for