Problem Switching on my MacBook Pro

Hello!
I am having a problem switching on my MacBook Pro. The screen is on with the apple but can't access my data. It shows that it's opening but it doesn't.
Can anyone help please?

there might be issue with the Hardware Device of Mackbook Pro, This issue is related to RAM , Try to contact Apple Tech Support or Fix an appoinment with Apple Genius in Apple store they might help u in resolving the issue.

Similar Messages

I am having a problem with my 2009 Macbook Pro

Hello Everyone,
I am having a problem with my 2009 Macbook Pro . A few weeks ago I plugged it into the charger after running it down to reserve battery power. It appeared to be charging, but then all of a sudden my clock and calender reset to year 2000 and then my computer blacked out and went dead. I tried to boot it up but nothing happened (literally nothing). I have tried 3 different chargers on it, but all I get is a faint green light and even after hours it still won't boot up. I have tried replacing the battery, but still nothing happens.
Any Ideas? I am pretty desperate to get my computer back up and running before school finals.

You may have to see if an authorized Apple service specialist can check over
the charging system (magsafe dc-in board, power adapter, and MacBook/Pro)
and test or run a diagnostic on it, to be sure there is no damage or failed parts.
When you attached the adapter to charge the computer, after it said it was going
to reserve power, did you shut down open applications and stop using the MB/Pro?
That would've been the thing to do, since the margin of run-time near the bottom
of the power cycle can be wrong by the gauge estimate, it can just quit.
While I have not researched your year/model/series in detail, I do know some
models of Apple portable computers have a small battery or capacitor on the
logic board, separate from the main power battery; it may need replacement.
A service provider w/ Apple training & parts would be a likely resource to fix it.
Good luck & happy computing!

New problem with display on Macbook Pro retina (Samsung panel)

Hello All,
I am a very new people on your forum but a few weeks ago i bought a new macbook pro retina with samsung panel.
I haven't ghosting effect on my macbook but i have a new and really bad problem.
I try to found a some information on Russians forums but nobody can help me with it.
I can see an artifacts in the form of flashing pixels on all display.
It occurs in 20-30 minutes after the start of work.
Today i try to test it on game Dirt 2 and i can see defects after 2 minutes after start. So i think it can be reason with Geforce 650 but when i back to desktop and use HD 4000 i still see a problem.
This is best seen on a black screen with high backlight.
When i try to connect TV via HDMI i can't see any problem in my TV.
So i really don't know what could be the reason.
I attached the video with issue to video hosting
http://vimple.ru/579f880e8b7045e09f8fc5bc097c5e2b
Also i have a many software problem like Crashing safari and iTunes. It can be a few times per day.
I really disappointed with my new Macbook.
I haven't any problem with old 2009 Macbook pro with Snow Leopard but Mountain Lion is not working well.

Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
Regards
TD

HT202879 I am switching to Apple macbook pro from Windows laptop. Is Apple compatible with Microsoft Office? How can I transport from Windows to Mac? What I have saved on external hardrives, will I be able to open it on Mac?

I am switching to Apple macbook pro from Windows laptop. Is Apple compatible with Microsoft Office? How can I transport from Windows to Mac? What I have saved on external hardrives, will I be able to open it on Mac?

Office for Mac, http://www.microsoft.com/mac/products, can open/edit/create Office documents.If your external drive is formatted NTFS then you can copy the Office documents to your computer and work on them. You won't be able to save the files back to your NTFS formatted drive. But you will be able to save the documents to your internal drive. You can move all the external files to your internal drive then format the external drive for Apple. Then you can copy the files back to your external drive for ongoing use.

I am switching to Apple macbook pro from Windows laptop. Is Apple compatible with Microsoft Office? How can I transport from Windows to Mac? What I have saved on external hardrives, will I be able to open it on Mac?

I am switching to Apple macbook pro from Windows laptop. Is Apple compatible with Microsoft Office? How can I transport from Windows to Mac? What I have saved on external hardrives, will I be able to open it on Mac?

Is Apple compatible with Microsoft Office?
Any computer is compatible as long as it can read and write Office files. But for perfect (or at least near perfect) compatibility, you would want to purchase Office 2011 for Mac.
How can I transport from Windows to Mac?
You can't directly transport any installation of Windows. All PC's come with a machine specific version of Windows intended for that PC. They don't have all of the hardware drivers the retail disks cover.
If you want Windows on your Mac, you would first purchase a full version copy (NOT an upgrade disk) of Windows 7 or 8. Those are the only supported versions on newer Macs. You install it through the supplied Boot Camp utility that comes with the Mac to create a new partition for Windows, and then install the retail copy of Windows you purchased.
The reason only these versions of Windows are supported is the same basic reason as a machine specific version of Windows for a PC. Apple only includes the necessary Mac hardware drivers for Win 7 or 8 on new Macs.
Once Windows is installed, you could then install the version of Office for Windows you already own. The nuisance of a Boot Camp partition is that you have to physically boot to either Windows or OS X, so you can only use the apps of the OS you're in at the time. To use both at once, you'd have to use virtual machine software (Parallels, VMware, VirtualBox) and then install Windows within that. Then you'd be able to run Windows inside of OS X and have access to both at the same time.

I am having problems shutting down my MacBook Pro. I go to the apple and click shutdown or restart, it appears the shutdown process starts, the screen goes blue and the little circle keeps going round and round, but nothing happens even after 30 minutes.

I am having problems shutting down my MacBook Pro. I go to the apple and click shutdown or restart, it appears the shutdown process starts, the screen goes blue and the little circle keeps going round and round, but nothing happens even after 30 minutes.

Make sure you quit all your applications before shutting down.
And try resetting the SMC.
Intel-based Macs: Resetting the System Management Controller (SMC)

HT1386 How do I switch users on wifi sync for example my Mac has two users one apples MacBook pro the other is my name I want to switch from apples MacBook pro to my name how is this done?

How do I switch users on wifi sync for example my Mac has two users one apples MacBook pro the other is my name I want to switch from apples MacBook pro to my name how is this done?

Try connecting the iPad to the computer that you do not want to WiFi sync with and uncheck the WiFi sync option in iTunes. Then click on Apply. Reboot the iPad and see if that does the trick.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

Has anyone else had problems scanning to their MacBook Pro from a Brother MFC device?

Has anyone else had problems scanning to their MacBook Pro from a Brother device?

Refer to http://support.apple.com/kb/HT3669. Check if Printer is listed and can function to Print and Scan.
Check if the computer can detect the Brother Device as a scanner. go to Applications and open up Image Capture. If it is not detected, contact Brother support

Mini Displayport to DVI Adapter Problem on Mid-2009 Macbook Pro

I have a new mid-2009 Macbook Pro hooked up to a 20" Samsung 2033sw LCD with a native 1600x900 resolution using a mini Displayport to DVI adapter that I bought off of EBay. No matter what I've tried I can't get anything to display on the external Samsung LCD higher than 1024x768. I tried switching between GPU's and that made no difference. Any ideas.?

Michael, thanks for the reply;
When you open System Preferences/Displays does a second preference panel open up OK on the Samsung ?
Yes, but I can't see it unless I select 'gather displays'. Then it appears on the MBP LCD, and showing the correct resolution - 1600x900.
Is there an Options Tab visible under which you can check 'Overscan' ?
None that I can find. Only display and color tabs.
Is the Refresh Rate set to 60.0 Hertz
Yes, that is what it shows in Refresh Rate.
I also pulled out an older LG LCD that is fairly generic, .e.g. it has DVI in at 1280x1024. Same problem on that LCD ... nothing higher than 1024x768, but this time at 1280x1024 I get major noise and screen distortion. The displayed image is jumping all over the place, but at least there is something displayed.

External Trackpad won't switch desktops on MacBook Pro

I have a 13-inch MacBook Pro and I recently purchased a standalone wireless keyboard and trackpad. The trackpad performs all of the gestures correctly, except for the four-finger swipe to switch between desktops. The built-in trackpad performs the four-finger swipe perfectly fine. I checked the System Preferences for the trackpad, but it looks like there's only one set of preferences for all trackpads.
My wife has a similar setup with her new iMac and she doesn't have the problem. Both trackpads switch desktops with a four-finger swipe. Weird, eh?
Any help would be greatly appreciated.

I think that the issue might be that there is no boot0 in /usr/standalone/i386. I have had similar issues lately when trying to make a bootable usb memory. I think this is necessary for the legacy option in the bless utility. If some one have a solution for this I would like to know as well.

Samsung hard drive problems with mid 2009 Macbook Pro

Arghh, this is driving me mad.
I'd like to know if anyone has installed a Samsung HM641JI SATA II hard drive into a mid 2009 Macbook Pro (mine is a 2.8Ghz) and, if so, how they managed it. The drive is 640GB. These are the steps I've taken:
1. Swap out the stock drive for the Samsung
2. Boot from a USB drive which contains a mirror of my system
3. When the system identified the new disk, I formatted it with 2 partitions (GUID table, HFS journaled)
4. Reboot
5. System is very slow. Boots from USB but can't use keyboard to login
6. Switch off and try again
7. Remove Samsung drive
8. Reboot from USB (works perfectly)
9. Downgrade firmware to 1.6
10. Replace samsung drive and try again
11. System boots from USB
12. Verify that drive is running at 1.5Ghz
13. Disk utility and system profiler both crash
14. Disk unmounts by itself and other random weirdness
15. Remove Samsung drive
I've read endless reports about the firmware in this model of Macbook Pro and its issues with SATA II but struggling to find anything current and specific. Two questions:
a. Is there anythign I can do to get this drive to play nicely?
b. What drive should I get if the answer to a is no?
As a bit of background.. my system began playing up last week with lots of spinning beach balls resulting in forced switch offs. Booting from a mirror on a USB drive works perfectly so I concluded that the drive was on its way out. A drive test utility confirmed this. I'm now wondering if it really was the drive or the cable or the logic board.
Any advice appreciated.
Cheers
//A

I'm coming around to the idea that this might be a problem with the SATA cable rather than the drive.
I currently have the stock drive (Hitachi) back in the macbook. It mounted for a while and was then ejected when I tried writing data to it. System profiler reports that "There was an error while scanning for Serial-ATA devices."
I was able to mount the same drive in a USB enclosure this afternoon without any problems. Right now, I seem to be having issues with both the Samsung drive and the Hitachi drive - I wasn't suspicious of thr latter because I thought it was failing.
I found one or two accounts of other people having similar problems that were resolved with a new sata cable.
How does a cable fail? Could this be my problem?
Cheers
//A

Lion login screen problems on Mid 2009 MacBook Pro

After upgrading my wife's Mid 2009 MacBook Pro from Snow Leopard to Lion we are seeing weird behavior on the login screen after the computer wakes from sleep mode.
The screen is only partially drawn (usually the top left 1/4 of the screen), and the grey background is shown instead of her desktop background picture. When you move the mouse around on the screen, it repaints blocks on the screen where the pointer has been.
This only seems to happen when the machine sleeps for a long period of time, e.g., overnight. When it just sleeps for a little while we don't see the issue.
When searching the forums for anyone else with the problem, several folks said that there was an issue with the video drivers for the 9400M card and recommended switching to the 9600M GT, but her machine only has the 9400M in it.
All other aspects of the system work fine.
Anyone else seeing this? Any clues?

Surprised there hasn't been anyone else experiencing this issue.
I have seen this on 2 new MBP 2.3mhz i5's with the Intel HD 3000 384mb graphics, Lion 10.7.3 & 10.7.4.
Also with the latest Lion firmware for the late 2011 MBP's that addresses compatibility and stability issues.
Hopefully there is a fix soon because the painting on my locked screen to login is getting annoying

Problems upgrading RAM for Macbook Pro 13" late 2011

First, thank you all for your assistance.
I don't know if this has happened to anyone yet. I have a 13" late 2011 MacBook Pro that came with a default 4 GB of RAM. I considered upgrading to 8 GB and problems arose: I had stripes 1 inch in lenght distributed across the screen. I've done some research and saw that it was a hardware problem with the Graphics Card/GPU. I switched back to the original 4 GB and so far so good, no problems. I did notice a few key things:
Originally I have 384 MB of Video Ram in the GPU
While using the 8 GB Ram upgrade, it said 512 (called my attention)
It reverted to 384 when switching to the original RAM
In the tech specs section of Apple Support site about my machine, it says that the Video RAM is "shared" with main memory. No other knowledge on that.
Could the RAM upgrade affected the memory supported by the GPU? Why did it increase? Is there any solution to this?
Thanks to everybody in advance.

It should - I've 16GB of RAM installed in my late 2011 15" and my built-in card now shows 512MB of VRAM. There might have been a problem with the RAM you installed. I would only buy Crucial, Kingston (not the 'value' brand), OWC or Corsair (again, not the 'value' brand).
Some RAM sellers simply have less than stellar performance using Macs. Make sure that you install the correct speed and specs as recommended by Apple.
Good luck,
Clinton

Problem with battery for MacBook Pro 2007

I have a problem with battery that was replaced during video card service 1.5 years ago
Battery health was around 80% and it stopped to work, I continued to use notebook with power cable and after week the battery become like this!
spoke with person in Apple store and got answer that it is not covered by Apple and I will need to buy another new battery.
For me it looks like manufacturing problem and I'm not expecting that after 1 year my battery will die like this! Thanks that it didn't explode!
What I should do in such case?

Thanks for your reply!
All my battery story is ending with bad taste...
I always relied on quality of the Apple products, it brought me to change all computers and phones to Apple brand. I was ready to pay extra for their products...
This battery has an Apple brand on it and I'm expecting that Apple will take some responsibility for it.
First battery on my MacBook Pro 2007 worked without any problem for 4 years, then it was replaced by Apple service tech person for unknown reason. This "new" battery failed just after ending of 1 year warranty coverage and even deformed in such scarry way. And now I don't have any option to ask if there is possibility that I'm experience a manufacturing defect! And I know that it is possible, internet is full of negative comments for these batteries!
Now I'm asking myself again, if it worst to buy Apple products? Are these products have proper quality?

What is the problem with 15-inch Macbook Pro model 2011 after connecting to TV with HDMI chord?

Today we connected a 15-inch Macbook Pro model 2011 with HDMI chord to an Insigna Television. We plugged and unplugged couple of times. But recently the macbook pro is having technical issues. The following symptoms are:
1. Macbook pro turns on and off
2. The screen stays blue and keeps loading but does not load to the desktop so you can't access to anywhere
3. The screen sometimes becomes fuzzy and the apple logo that shows before it loads to the desktop is fuzzy
4. Sometimes fuzzy lines appear on the screen like you see on television when there's a bad signal
5. The screen stays blue
6. Sometimes little specks appear on the screen
Only thing we did was turn it off and restart but it still leads to the same symptoms above.
Does anyone have any clue what caused this problem? I am guessing it is due to the connection to the HDMI chord, since we didn't turn the macbook on and off when we plugged it, rather we just unplugged and plugged the chord while the macbook is running.
Another theory might be watching movies from an online source but the first theory seems to make more sense.
We scheduled a meeting with the genius bar tomorrow but does anyone might have any clue? And also any ideas how to fix this? This is an emergency because there are important files on the macbook we didn't back up and we hope the files are safe and we need to use the macbook ASAP. Let us know anything that might have caused this and/or any solutions or help. That would be appreciated and thank you.

Hey there! Welcome to the Discrete GPU issue clube ... post your relate here >>> 2011 MacBook Pro and Discrete Graphics Card
And for GOD SAKE! Call Apple to tell them that you're another user with such problem ... that action can improve a future recall. BTW the fix price for your problem is around U$ 1000,00 ... that's the meaning of the recall attempt

Problem Switching on my MacBook Pro

Similar Messages

Maybe you are looking for