Problem to register ATA 186 with CME 7.0

Hello,
I have to two ATA connected into switch that are connected with Cisco 2851.
The first ATA was connected in the past and it works well, now I need to connect another ATA but I don't be able to register in CME.
Both ATA have the same version of firmware, and got ip by the dhcp.
I've checked the ports in switch where are connected the ata's and have the same configuration.
To register the new ATA I go into CME portal and when I try to add a new phone I receive a message that say "no new phone to add".
Please help me to fix it
Thanks
Regards

Hello,
thanks for the answers.
I solved the new ATA was registred automaticaly in cme with a randon telephone number, for this reason I wasn't able to find it.
With the command show ephone register I checked all the phones registered with the number and I finded the new ata.
Thanks for your help,
Regards

Similar Messages

Configuring FAX on ATA 186 with CME 3.4

Hi,
I have an ATA 186 connected to my network, I have configured CME for auto assign extensions & I got an extension as well, when I connect analog phone it works fine but when I connect FAX Machine I cannot send & recieve fax. Do I need to change any configurations in ATA???? Please check the screen shot attached

Try this link for more information on configuraing FAX on ATA
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml

Facing problems in Registering AIA Components with OSB

Hi all,
I am trying to implement AIA on OSB for that as an initial step I am trying to Register AIA Components with OSB.
In this step I am facing problems getting 705 conflicts removing these conflicts manually is a huge task .
Can anyone suggest me good approach or if any one has removed AIA components jar please share with me.
Thanks
Phani

Hi Madhavi,
You said:
OMB+> OMBALTER LOCATION 'TEST_LOCATION' SET PROPERTIES ( HOST, PORT, SERVICE_NAME , SCHEMA, CONNECT_AS_USER,PASSWORD, VERSION, UOID,DATABASE_NAME) \
VALUES ( '$HOST', $PORT,'$SERVICE', '$TgtDBUser', '$TgtDBUser', 'TgtDBPWD','$
dbversion','true','$SERVICE');
Did you leave out the "$"-character for the TgtDBPWD variable in purpose? Could this be the source of your problem?
Regards,
Ed

ATA-186 with overhead paging systems

Since the ATA-186 supplies 600 Ohms, would I need a seperate device such as a Bogen TAM-B to supplie the audio for overhead paging, or could I just use the ATA-186?

ATA-186 can be used as an audio source.

Ata 186 with Polycom MGC 100

I'm trying to setup an audio conference on a Polycom MGC100 with a Cisco Ata186. I can dial out to the Ata using the IP address and the Ata will answer but it disconnectes after 30 seconds. Has anyone else tried this and if so what were your results? Thanks.

I have the same problem as well with CM 6, however my calls last about 30 minutes then disconnect.
Has anyone found a solution?

ATA 186 with External Bogen Night Ringer

Using Call Manager, I am using an ATA with and External Bogen Night Ringer. It works when I call the ATA extension and the Speakers Ring out but when I call forward a ip phone to the ATA DN the speakers do not output anything. My goal is to call forward the main DN of the receptionist to the ATA hooked up to the Bogen TPU-100B paging unit that has the night ringer functionality. I thought it might be some sort of gateway issue but the call forward does not work from IP Phone Calling another IP Phone that is call forwarded to the ATA with the Night Ringer. Does anyone have any ideas.

http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=IP%20Communications%20and%20Video&topic=Video%20over%20IP&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.ee944f1/3
I think the ring voltage is not suffecient enough from the FXO being passed to the ATA, I think I need to viking RG-10A to sit inline and boost increase power on the line. The Bogen requires 90V.

Problem while registering ESB Process with integration server

Hi All,
I am facing an error while registering the ESB Process in Intergration Server. I am getting the following error in ESB.
"Registration of ESB Process (Process Name) is failed, Exception: Connection Refused. connect Check the Integration Server Connection is correctly configured and the Integration Server is up and Running"
I am able to deploy the BPEL process from the Jdeveloper using the same Integration Server Connection parameter. Also I have checked the Intergration server and its up and running.
Any Help or Pointers to this issue is helpful.
Thanks in advance,
Saravana

Yes, but you are getting connection refused which is more thank likely cause by the application server connection failure.
If you should see a details button when testing the connection can you please provide result of this.
It looks like you have entered a wrong port, hostname, or oc4j instance.
If you go to your OS
cd SOA_HOME/opmn/bin
run the command
opmnctl status -l
you will see all the ports for your instance. Now revisit both the application server and Integration server settings mad make sure they are set correctly. Especially the hostname and the port for the application server
Also make sure your proxies are correct in JDeveloper
Tools -> preferences -> web browser & proxy

ATA 186 for FAX With CME

Hi,
I have ATA 186 connected to my network when i connect a phone it works but when I connected fax machine i cannot recieve or send faxes...do I need to do any configurations in ATA...please check the attachment..

you'll need dial peer(s), on your CME router, that enable FAX passthrough as well as a few other pieces.
please see the following link for Config/Troubleshooting ATA-186 with FAX:
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml#task2

ATA 186 - Faxing with sccp on CCME

Is there any specific config required to get a fax working with an ATA 186 with sccp, both in the ATA settings and ccme config ?
Any useful links or example configs would be a great help
Thanks in advance

Hey Mark,
Here are some good ATA - Fax related docs;
Field Notice: Fax Passthrough Limitations on ATA 186
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_field_notice09186a0080094af7.shtml
Configuring the Cisco ATA for SCCP
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00801e0e0c.html
Configuring and Debugging Fax Services
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00801e0dff.html
Hope this helps!
Rob

Troubleshooting an ATA 186

How can I tell what digits are being passed from a phone plugged into an ATA 186?
We have an ATA 186 with a credit card machine plugged into it that is failing to place calls. When I monitor the call with a butt set I hear dial tone, then 1 digit being dialed and then an error from callmanager basically telling me to check the number. The call never gets past that first digit. If I use a butt set to place a call everything works fine. I'm concerned the digit being passed is not the access code of 8, and I want to verify that. I have also included the 9001.log from the prsrev.exe I just don't know how to read it.

Hi,
It look to me like the ATA isn't configured properly in CCM?
There's a lot of messages in the log stating "RegRej[1]:Error: DB Config", which I think means the device isn't registering properly.
Have you checked the ports are configured properly?
Here's a troubleshooting guide which may also help:
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a0080094adf.shtml
Please rate if useful...

ATA-186 can be registered with CUCM v10.5

Hello guys ;
Please confirm me that ATA-186 can work with CUCM v10.5 ? .
Regards;
Shib

Loaded the latest firmware into CM, then manually on ATA firmware using this process as CM didn't change it:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaapc.html#wp1011450
I followed this link from another post regarding ASA not registering for an older issue.
http://www.cisco.com/en/US/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccpaape.html#wpxref59054
Follow the part that mentions setting the SID0 & SID1 to "." no quotes. I did this and my ATA registered to CM. Screen caps attached.
I have a Cisco ATA 186 running on 10.5.1 and it shows to be registered. I can make calls on it. Not sure how it will do for faxes. HTH Please rate.

Registering SPA500 series IP phone with CME 8.6

Hello friends. I'm newbie with CME configuration, but now I'm asked to register SPA504G phones onto a CME 8.6 installed on a Cisco 2911 router using SIP protocol. I'm testing with a SPA 502G phone with software version 7.4.7. Within "voice register global" configuration I can't find "load" command for thisphoone model. About phone files, I only found "spa50x-30x-7-4-8a.bin" file for this phone and loaded into flash: unit.
How can I make SPA 500G phone be registered with this CME? I would appreciate somebody can help me with a guide to achieve this.
Thanks in advance for your help.
Best regards
Joe

I have the same problem.
Can anyone help?
Thank you.

7921 not registering with CME through repeater

I have this environment:
CME 7.0 running in Cisco2851.
WLC2106 with 6 1242 APs
15 phones 7921
I have to extend the wireless coverage to an specific point (warehouse), 150 meters away. This point only have a PC and a phone, so I don't think a bridge is necessary. I have an 1131 AP configured as repeater. In my tests (locally) I see the 1131 is registering to the main wireless network. Using site survey feature in the 7921 I see the SSID broadcast from the repeater AP, but if I use Neighbor list feature the network is not allocated and obviously the phone can't register with CME. Only for tests I had disabled all security features for this SSID.
The 1131 association table only shows the root AP but it indicates the IP address assigned to the controller.
Can somebody give me some tips to identify what I'm missing?
Thanks in advance

I think H-REAP is a feature not usable for this case, isn't
I'm reading the "Cisco Wireless LAN Controller Configuration Guide", in page 7-19 and follow, Workgrouup Bridge is explained. I think it should be the solution for my requirements, although I will test tomorrow (Wendesday), I have some questions:
The example shows a hub in remote site, I guess it can be replaced with a switch without any problem.
Could it be possible to set another AP attached to the switch to get wireless access? Otherwise, I will need a desktop phone.
The manual indicates NO VLAN are supported (page 7-21), so this option will need PC and phone for this site running in the same VLAN?
I appreciate your assistance.
Daniel Escalante.

Ata 186 second port problem

Hello
There are a atas186 who was registered to a CUCM version 6.1,the call manager was migrated to version 8.6 but now the second por when a call is answered immediately when give a fast busy tone, the first port works perfect, and i have changed many parameters and did a factory reset without success.
S/W Version 3.02.04(090202A)
App Load ID ATA030204SCCP090202A
Thanks.

Your ata´s place calls across the wan?
If yes, the the ata 186, only support one port in g729 codec the port 0, the second port works only in g711 codec so try to configure a region to place calls only in g711 codec across the wan and problem solve
i hope it helps...

I have never been able to use the Macmail feature. Running OSX 10.4.11, and the problems appear to be related to the fact that I originally registered my computer with apple, I subsequently changed my e-mail address. Have since upgraded the e-mail addre

I have never been able to use the Macmail feature. Running OSX 10.4.11, and the problems appear to be related to the fact that when I originally registered my computer with apple, I used an old e-mail address which is now defunct. Have since upgraded the e-mail address in account manger, but it still locks me out and rejects my user name and password when I try to log in. It seems it established an account for me automatically when I first fired the beast up, but now the Macmail program is uncooperative with me. Any assistance would be much appreciated, Thanks

Hi rbcjoker76, and a warm welcome to the forums!
Sounds like some needed System Fonts wre replaced by bad ones. Y also have Font Book in Applications for validating fonts & checking for duplicates.
Required Fonts from 10.3, much the same in 10.4...
http://support.apple.com/kb/HT2444?viewlocale=en_US
You may have to get Pacifist...
http://www.charlessoft.com/
then intall the Fonts what you need from your Install Disk.
Or do a relatively painless Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space and no Disk corruption, and is relatively quick & painless...
http://docs.info.apple.com/article.html?artnum=107120
Just be sure to select Preserve Users & Settings.

Problem to register ATA 186 with CME 7.0

Similar Messages

Maybe you are looking for