Problem using asterisk symbol (*) in Translation Rule

Hello Everybody
Please any suggestion to make a translation from *100.. to 011056000
I have tried using num-exp and a translation rule but symbol asterisk is not supported as a prefix.
Thanks in advance

try
CUBE(config)#voice translation-rule 1
CUBE(cfg-translation-rule)#rule 1 /\*100../ /011056000/

Similar Messages

Problem using field symbols in Query...

Hi,
I am fetching the name of the table and field which I will be using in the query using field symbols. But it gives syntax error...
select single OBJECTTABLE OBJECTFIELD into help_numtab from Zobjectname
where OBJECTNAME = P_OBJECT.
field-symbols : <number> type any.
field-symbols : <module> type any.
ASSIGN help_numtab-OBjectfield to <number>.
ASSIGN help_numtab-OBjecttable to <module>.
/* Here <number> = MATNR and <module> = MARA.
select <NUMBER> into table help_item
from <MODULE>
where ERNAM = SY-UNAME.
This gives a syntax error which says <module> is not defined in ABAP DDIC.

instead of field symbols, you ccan try this..
select (help_numtab-OBjectfield) into table help_item
from (help_numtab-OBjecttable)
where ERNAM = SY-UNAME.
~Suresh

ANYBODY used the Currrency Conversion / Translation Rules Table yet??? Thx

hi guys,
we are working on the BUSINESS RULE: CURRENCY CONVERSION TABLE.
here we have a easy three row table:
Account Rate Type: AVG; Formula: [AVG]
Account Rate Type: END; Formula: [END]
Line 3: Account Rate Type: TRANS: Destination Account: XYZ; >> Formula:[END]-[AVG]
this works fine and great!!!!! differences within accounts of AVG and accounts of END between AVG to END rate are being posted in Account XYZ.
here the is the requirement we trying to establish:
for Line 3: using the AVG (of ACTUALS) and the AVG (of BUDGET) ... so different VERSIONS of the SAME ACCOUNT_1. We like to have the same differences (but differen versions) posted to XYZ account.
what calculation do i put in the Formula field in the chart???
anybody done this? got an idea? -
thanks a lot, max (BPC 7.0 NW)
Edited by: Maximilian Weisheit on Jun 10, 2009 10:43 PM
Edited by: Maximilian Weisheit on Jun 10, 2009 10:47 PM

Thanks Ethans that was good explanation. So, we stayed within the version and the calculation worked fine. However, now I am wondering about the following:
We take the [END]-[AVG] and we get the wanted result. let's say 1.5 - 1.3 = 0.2 ... So desitnation account will post 0.2. - Correct!
Now if i run Currency Conversion / FX Trans again. it again takes 1.5 - 1.3 = 0.2 and it adds this 0.2 to the already noted 0.2 in the account = 0.4 in total. Run CC again an addiotional difference of 0.2 to the already there 0.4 which equals 0.6 total; and so on. It is adding on top what has been posted, not continiously just showing the difference in accounts.
How do i modify that it is NOT adding, but everytime ONLY finding the difference?
Thanks a lot, Max
PS: Also I am wondering if anybody has detailed information on the Business Rule Table for Currency Conversion. - The BPC NW Help is rather light on the TABLE information.
Edited by: Maximilian Weisheit on Jun 15, 2009 11:44 PM

Safari Crash - Problem with doodle (planer) app - doodle web links cause safari to crash with a very strange message "Error - Please make sure Safari is not used in Private Modus" (translated from german) No Privat Modus buttom in ios 7 safari settings!

Safari Crash - Problem with doodle (planer) app - doodle web links cause safari to crash with a very strange message "Error - Please make sure Safari is not used in Private Modus" (translated from german) No Privat Modus buttom in ios 7 safari settings! Works fine with an older Safari Version. Web link, call doodle app. You could see the website in the backround working but safari crashes after clicking on the error window. Any suggestions?

Turn off Private Browsing.
Tap "Private" on Safari Screen to disable Private Browsing. When top of screen is white, Private Browsing is off.

I have a problem using Pages. Whenever I type fl I get a symbol instead. Does anyone else have this problem?

I have a problem using Pages. Whenever I type fl I get a symbol instead. Does anyone else have this problem?

Hi Tom
On my machine it seems that the fi ligature doesn't exist with Times New Roman (installed version is 5.01.3x)
It's available in Warnock Pro but the st one which is designed in Warnock doesn't apply.
This last screenshot was made from Linotype Explore, the old free version.
Typography isn't really easy, even with modern tools
Yvan KOENIG (VALLAURIS, France) lundi 6 juin 2011 14:53:01
iMac 21”5, i7, 2.8 GHz, 4 Gbytes, 1 Tbytes, mac OS X 10.6.7
Please : Search for questions similar to your own before submitting them to the community
To be the AW6 successor, iWork MUST integrate a TRUE DB, not a list organizer !

Truncate called number using translation rule

I have a Cisco 2851 router and I need to chop off the first digit in the incoming
called number string (e,g 272109 translate to 72109).
I have tried using rule 1 /^.*$..$/ /\1/ but I cannot get this to work, keeps saying it is an incomplete command.
Can anyone help please

Are the numbers always the same length? If so, you can use the following rule to keep the last 5 digits.
voice translation-rule 1
rule 1 /^.*$.....$/ /\1/
Hope this helps.
Brandon

Problem in using Field Symbols in HIDE statement

Hi All,
I am working in an Upgrade project ( from 4.6B to ECC 5.0 ). In a program I found few warnings on HIDE statement because they have used Field Symbols in HIDE statement.
The warning is " HIDE on a field symbol is dangerous, but the formal parameter "" is not ".
and the piece of code is
SET EXTENDED CHECK OFF.
HIDE: flg_pick_up, <s1>, <s2>, <s3>, <s4>, <s5>, z_feld_ind.
CLEAR flg_pick_up.
SET EXTENDED CHECK ON.
all the field symbols are of type ANY. SO can any one help in removing those warnings.
Please reply me as soon as possible.
With Regards,
Amarnath Singanamala

Hi amarnath,
1. Why do u want to remove
the warning ?
2. This warning (and not an error)
is a GENUINE warning,
which the system wants the user to make aware of.
3. By doing some xyz,
even if u may be able to hide the warning,
the warning may be hidden (for display purpose only),
but,
the warning will still be there inside the system.
4. I think u should ignore the warning,
(if there are no other repurcussions).
regards,
amit m.

Re: Problem in ALV reports using Field symbols

Hi Friends,
Can you tell me how to convert a normal report using field symbols into ALV report
can ypu please suggest me any solutions.I am sending the code along with this mail.
Regards,
Dinesh
<b>Coding:</b>
*& Report YSDBTEMP                                                    *
REPORT YSDBTEMP                                .
tables: ekko , ekpo .
TYPE-POOLS: SLIS.
*Internal Table Declaration
data: begin of line ,
      ebeln like ekko-ebeln , "Purchasing Document No.
      bedat like ekko-bedat , "Purchasing Document Date
      matnr like ekpo-matnr , "Material No.
      netwr like ekpo-netwr , "Net Order Value in PO Currancy
      meins like ekpo-meins , "UOM
      change like ekpo-menge ,
end of line .
*Internal table Declaration
DATA: IT_final like table of line with header line.
DATA : FIELDCATALOG TYPE SLIS_T_FIELDCAT_ALV with header line.
DATA : V_REPID TYPE SYREPID.
DATA : IT_LISTHEADER TYPE SLIS_T_LISTHEADER.
data : i_layout type slis_layout_alv .
Header for Main Grid Display
data:i_header1 type slis_t_listheader with header line.
Header for Interactive Report Display
data:i_header2 type slis_t_listheader with header line.
*Field Symbol declaration.
FIELD-SYMBOLS: <FS> type any table.
**select option Declaration
selection-screen begin of block block.
select-options: s_ebeln for ekko-ebeln .
selection-screen end of block block .
start-of-selection.
perform get_data.
perform field_cat.
perform layout using i_layout .
perform grid_display .
*&      Form get_data
      text
--> p1        text
<-- p2        text
FORM get_data .
SELECT EKKO~EBELN
EKKO~BEDAT
EKPO~EBELP
EKPO~MATNR
EKPO~NETWR
EKPO~MEINS
EKPO~MENGE
EKPO~BPRME
INTO CORRESPONDING FIELDS OF table IT_FINAL
FROM EKKO INNER JOIN EKPO ON EKKOEBELN = EKPOEBELN
WHERE EKKO~EBELN IN S_EBELN.
ENDFORM.                    " get_data
*&      Form field_cat
      text
--> p1        text
<-- p2        text
FORM field_cat .
fieldcatalog-fieldname = 'EBELN'.
fieldcatalog-seltext_m = 'Purchase Order No'.
fieldcatalog-col_pos = 1.
   append fieldcatalog .
clear fieldcatalog.
fieldcatalog-fieldname = 'BEDAT'.
fieldcatalog-seltext_m = 'Purchasing Document Date'.
fieldcatalog-col_pos = 2.
   append fieldcatalog .
clear fieldcatalog.
fieldcatalog-fieldname = 'MATNR'.
fieldcatalog-seltext_m = 'Material No'.
fieldcatalog-col_pos = 3.
   append fieldcatalog .
clear fieldcatalog.
fieldcatalog-fieldname = 'MATNR'.
fieldcatalog-seltext_m = 'Net order'.
fieldcatalog-col_pos = 4.
   append fieldcatalog .
clear fieldcatalog.
ENDFORM.                    " field_cat
*&      Form layout
      text
     -->P_I_LAYOUT text
FORM layout USING    P_I_LAYOUT.
i_layout-lights_tabname = 'IT_FINAL'.
i_layout-box_tabname = 'IT_FINAL'.
ENDFORM.                    " layout
*&      Form grid_display
      text
--> p1        text
<-- p2        text
FORM grid_display .
CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
EXPORTING
I_CALLBACK_PROGRAM = SY-REPID
I_CALLBACK_PF_STATUS_SET = 'SET_PO_PF_STATUS'
I_CALLBACK_USER_COMMAND = 'USER_COMMAND'
IS_LAYOUT = I_LAYOUT
IT_FIELDCAT = FIELDCATALOG[]
*IT_EVENTS = I_EVENT[]
TABLES
t_outtab = <fs>.
endform.

Hi,
This is one sample program,
Check this.
I hope it is helpful to you.
TABLES : zeastable_02,zeastable_04.
TYPE-POOLS : slis.
TYPES : BEGIN OF fieldst,
        name LIKE zeastable_02-name,
        znum LIKE zeastable_02-znum,
        empno LIKE zeastable_04-empno,
        zempsalary LIKE zeastable_04-zempsalary,
        END OF fieldst.
DATA itab TYPE TABLE OF fieldst WITH HEADER LINE.
DATA: w_report_id LIKE sy-repid.            "Program name
DATA: w_title   TYPE lvc_title VALUE    'Assignment 1 in ALV'.
DATA: w_layout   TYPE slis_layout_alv.      "Layout setup
DATA: w_fieldcat TYPE slis_t_fieldcat_alv. "Field Catlog
START-OF-SELECTION.
SELECT-OPTIONS employee FOR zeastable_04-empno.
SELECT zeastable_02name zeastable_02znum
       zeastable_04empno zeastable_04zempsalary
       INTO CORRESPONDING FIELDS OF TABLE itab FROM
       zeastable_02 INNER JOIN zeastable_04 ON
       zeastable_02name = zeastable_04name
       WHERE zeastable_04~empno IN employee.
w_report_id = sy-repid.
PERFORM i_layout CHANGING w_layout.
PERFORM i_fieldcat CHANGING w_fieldcat.
CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
    EXPORTING
    i_callback_program                = 'ZEASALV_04'
     i_grid_title                      = w_title
     is_layout                         = w_layout
     it_fieldcat                       = w_fieldcat
     i_save                            = 'A'
    TABLES
      t_outtab                          = itab
   EXCEPTIONS
     program_error                     = 1
     OTHERS                            = 2
IF sy-subrc <> 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
            WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
PERFORM i_layout CHANGING w_layout.
PERFORM i_fieldcat CHANGING w_fieldcat.
*&      Form i_layout
      text
     <--P_W_LAYOUT text
form i_layout changing p_w_layout.
clear w_layout.
w_layout-colwidth_optimize = 'X'.
w_layout-edit = ' '.
endform.                    " i_layout
*&      Form i_fieldcat
      text
     <--P_W_FEILDCAT text
form i_fieldcat changing p_w_feildcat.
data: l_line_fieldcat type slis_fieldcat_alv.
clear l_line_fieldcat.
l_line_fieldcat-fieldname = 'NAME'.
l_line_fieldcat-ref_tabname = 'itab'.
l_line_fieldcat-seltext_m = 'NAME'.
l_line_fieldcat-key = 'X'.
   append l_line_fieldcat to w_fieldcat.
clear l_line_fieldcat.
l_line_fieldcat-fieldname = 'ZNUM'.
l_line_fieldcat-ref_tabname = 'itab'.
l_line_fieldcat-seltext_m = 'NUMBER'.
l_line_fieldcat-key = 'X'.
append l_line_fieldcat to w_fieldcat.
clear l_line_fieldcat.
l_line_fieldcat-fieldname = 'EMPNO'.
l_line_fieldcat-ref_tabname = 'itab'.
l_line_fieldcat-seltext_m = 'EMPLNUM'.
*l_line_fieldcat-key = 'X'.
append l_line_fieldcat to w_fieldcat.
clear l_line_fieldcat.
l_line_fieldcat-fieldname = 'ZEMPSALARY'.
l_line_fieldcat-ref_tabname = 'itab'.
l_line_fieldcat-seltext_m = 'SALARY'.
*l_line_fieldcat-key = 'X'.
append l_line_fieldcat to w_fieldcat.
endform.                    " i_fieldcat
Reward for useful answers.

How to use field symbol in select

Hi,
    CONCATENATE 'WTG0' LV_MON INTO LV_FNAME.
    ASSIGN (LV_FNAME) TO <FS>.
    SELECT SINGLE <FS> FROM COSP INTO LV_SAPRST
         WHERE OBJNR = LV_OBJ AND GJAHR = LV_YEAR AND WRTTP = '4' AND KSTAR = GT_INOUT-SAKNR
   Error message :    Unknown column name "<FS>" . field list. . field list. field list.
   actually , if i use if command, i can do, but i want to use simple code by fieldsymbol.
   is it possible in select command?
Thanks in advance
Benjamin

Hi
Hope it will help you.
reward if help.
Field Symbols
Field symbols are placeholders or symbolic names for other fields. They do not physically reserve space for a field, but point to its contents. A field symbol cam point to any data object. The data object to which a field symbol points is assigned to it after it has been declared in the program.
Whenever you address a field symbol in a program, you are addressing the field that is assigned to the field symbol. After successful assignment, there is no difference in ABAP whether you reference the field symbol or the field itself. You must assign a field to each field symbol before you can address the latter in programs.
Field symbols are similar to dereferenced pointers in C (that is, pointers to which the content operator * is applied). However, the only real equivalent of pointers in ABAP, that is, variables that contain a memory address (reference) and that can be used without the contents operator, are reference variables in ABAP Objects.
All operations programmed with field symbols are applied to the field assigned to it. For example, a MOVE statement between two field symbols moves the contents of the field assigned to the first field symbol to the field assigned to the second field symbol. The field symbols themselves point to the same fields after the MOVE statement as they did before.
You can create field symbols either without or with type specifications. If you do not specify a type, the field symbol inherits all of the technical attributes of the field assigned to it. If you do specify a type, the system checks the compatibility of the field symbol and the field you are assigning to it during the ASSIGN statement.
Field symbols provide greater flexibility when you address data objects:
If you want to process sections of fields, you can specify the offset and length of the field dynamically.
You can assign one field symbol to another, which allows you to address parts of fields.
Assignments to field symbols may extend beyond field boundaries. This allows you to address regular sequences of fields in memory efficiently.
You can also force a field symbol to take different technical attributes from those of the field assigned to it.
The flexibility of field symbols provides elegant solutions to certain problems. On the other hand, it does mean that errors can easily occur. Since fields are not assigned to field symbols until runtime, the effectiveness of syntax and security checks is very limited for operations involving field symbols. This can lead to runtime errors or incorrect data assignments.
While runtime errors indicate an obvious problem, incorrect data assignments are dangerous because they can be very difficult to detect. For this reason, you should only use field symbols if you cannot achieve the same result using other ABAP statements.
For example, you may want to process part of a string where the offset and length depend on the contents of the field. You could use field symbols in this case. However, since the MOVE statement also supports variable offset and length specifications, you should use it instead. The MOVE statement (with your own auxiliary variables if required) is much safer than using field symbols, since it cannot address memory beyond the boundary of a field. However, field symbols may improve performance in some cases.
check the below links u will get the answers for your questions
http://help.sap.com/saphelp_nw04/helpdata/en/fc/eb3860358411d1829f0000e829fbfe/content.htm
http://www.sts.tu-harburg.de/teaching/sap_r3/ABAP4/field_sy.htm
http://searchsap.techtarget.com/tip/1,289483,sid21_gci920484,00.html
Syntax Diagram
FIELD-SYMBOLS
Basic form
FIELD-SYMBOLS <fs>.
Extras:
1. ... TYPE type
2. ... TYPE REF TO cif
3. ... TYPE REF TO DATA
4. ... TYPE LINE OF type
5. ... LIKE s
6. ... LIKE LINE OF s
7. ... TYPE tabkind
8. ... STRUCTURE s DEFAULT wa
The syntax check performed in an ABAP Objects context is stricter than in other ABAP areas. See Cannot Use Untyped Field Symbols ad Cannot Use Field Symbols as Components of Classes.
Effect
This statement declares a symbolic field called <fs>. At runtime, you can assign a concrete field to the field symbol using ASSIGN. All operations performed with the field symbol then directly affect the field assigned to it.
You can only use one of the additions.
Example
Output aircraft type from the table SFLIGHT using a field symbol:
FIELD-SYMBOLS <PT> TYPE ANY.
DATA SFLIGHT_WA TYPE SFLIGHT.
ASSIGN SFLIGHT_WA-PLANETYPE TO <PT>.
WRITE <PT>.
Addition 1
... TYPE type
Addition 2
... TYPE REF TO cif
Addition 3
... TYPE REF TO DATA
Addition 4
... TYPE LINE OF type
Addition 5
... LIKE s
Addition 6
... LIKE LINE OF s
Addition 7
... TYPE tabkind
Effect
You can define the type of the field symbol using additions 2 to 7 (just as you can for FORM parameters (compare Defining the Type of Subroutine Parameters). When you use the ASSIGN statement, the system carries out the same type checks as for USING parameters of FORMs.
This addition is not allowed in an ABAP Objects context. See Cannot Use Obsolete Casting for FIELD SYMBOLS.
In some cases, the syntax rules that apply to Unicode programs are different than those for non-Unicode programs. See Defining Types Using STRUCTURE.
Effect
Assigns any (internal) field string or structure to the field symbol from the ABAP Dictionary (s). All fields of the structure can be addressed by name: <fs>-fieldname. The structured field symbol points initially to the work area wa specified after DEFAULT.
The work area wa must be at least as long as the structure s. If s contains fields of the type I or F, wa should have the structure s or at least begin in that way, since otherwise alignment problems may occur.
Example
Address components of the flight bookings table SBOOK using a field symbol:
DATA SBOOK_WA LIKE SBOOK.
FIELD-SYMBOLS <SB> STRUCTURE SBOOK
DEFAULT SBOOK_WA.
WRITE: <SB>-BOOKID, <SB>-FLDATE.
Related
ASSIGN, DATA
Additional help
Declaring Field Symbols

How to use field symbols in program

how to use field symbols can any one explain with example please..
Regards,
venki...

Hi
Field Symbols
Field symbols are placeholders or symbolic names for other fields. They do not physically reserve space for a field, but point to its contents. A field symbol cam point to any data object. The data object to which a field symbol points is assigned to it after it has been declared in the program.
Whenever you address a field symbol in a program, you are addressing the field that is assigned to the field symbol. After successful assignment, there is no difference in ABAP whether you reference the field symbol or the field itself. You must assign a field to each field symbol before you can address the latter in programs.
Field symbols are similar to dereferenced pointers in C (that is, pointers to which the content operator * is applied). However, the only real equivalent of pointers in ABAP, that is, variables that contain a memory address (reference) and that can be used without the contents operator, are reference variables in ABAP Objects.
All operations programmed with field symbols are applied to the field assigned to it. For example, a MOVE statement between two field symbols moves the contents of the field assigned to the first field symbol to the field assigned to the second field symbol. The field symbols themselves point to the same fields after the MOVE statement as they did before.
You can create field symbols either without or with type specifications. If you do not specify a type, the field symbol inherits all of the technical attributes of the field assigned to it. If you do specify a type, the system checks the compatibility of the field symbol and the field you are assigning to it during the ASSIGN statement.
Field symbols provide greater flexibility when you address data objects:
If you want to process sections of fields, you can specify the offset and length of the field dynamically.
You can assign one field symbol to another, which allows you to address parts of fields.
Assignments to field symbols may extend beyond field boundaries. This allows you to address regular sequences of fields in memory efficiently.
You can also force a field symbol to take different technical attributes from those of the field assigned to it.
The flexibility of field symbols provides elegant solutions to certain problems. On the other hand, it does mean that errors can easily occur. Since fields are not assigned to field symbols until runtime, the effectiveness of syntax and security checks is very limited for operations involving field symbols. This can lead to runtime errors or incorrect data assignments.
While runtime errors indicate an obvious problem, incorrect data assignments are dangerous because they can be very difficult to detect. For this reason, you should only use field symbols if you cannot achieve the same result using other ABAP statements.
For example, you may want to process part of a string where the offset and length depend on the contents of the field. You could use field symbols in this case. However, since the MOVE statement also supports variable offset and length specifications, you should use it instead. The MOVE statement (with your own auxiliary variables if required) is much safer than using field symbols, since it cannot address memory beyond the boundary of a field. However, field symbols may improve performance in some cases.
check the below links u will get the answers for your questions
http://help.sap.com/saphelp_nw04/helpdata/en/fc/eb3860358411d1829f0000e829fbfe/content.htm
http://www.sts.tu-harburg.de/teaching/sap_r3/ABAP4/field_sy.htm
http://searchsap.techtarget.com/tip/1,289483,sid21_gci920484,00.html
Syntax Diagram
FIELD-SYMBOLS
Basic form
FIELD-SYMBOLS <fs>.
Extras:
1. ... TYPE type
2. ... TYPE REF TO cif
3. ... TYPE REF TO DATA
4. ... TYPE LINE OF type
5. ... LIKE s
6. ... LIKE LINE OF s
7. ... TYPE tabkind
8. ... STRUCTURE s DEFAULT wa
The syntax check performed in an ABAP Objects context is stricter than in other ABAP areas. See Cannot Use Untyped Field Symbols ad Cannot Use Field Symbols as Components of Classes.
Effect
This statement declares a symbolic field called <fs>. At runtime, you can assign a concrete field to the field symbol using ASSIGN. All operations performed with the field symbol then directly affect the field assigned to it.
You can only use one of the additions.
Example
Output aircraft type from the table SFLIGHT using a field symbol:
FIELD-SYMBOLS <PT> TYPE ANY.
DATA SFLIGHT_WA TYPE SFLIGHT.
ASSIGN SFLIGHT_WA-PLANETYPE TO <PT>.
WRITE <PT>.
Addition 1
... TYPE type
Addition 2
... TYPE REF TO cif
Addition 3
... TYPE REF TO DATA
Addition 4
... TYPE LINE OF type
Addition 5
... LIKE s
Addition 6
... LIKE LINE OF s
Addition 7
... TYPE tabkind
Effect
You can define the type of the field symbol using additions 2 to 7 (just as you can for FORM parameters (compare Defining the Type of Subroutine Parameters). When you use the ASSIGN statement, the system carries out the same type checks as for USING parameters of FORMs.
This addition is not allowed in an ABAP Objects context. See Cannot Use Obsolete Casting for FIELD SYMBOLS.
In some cases, the syntax rules that apply to Unicode programs are different than those for non-Unicode programs. See Defining Types Using STRUCTURE.
Effect
Assigns any (internal) field string or structure to the field symbol from the ABAP Dictionary (s). All fields of the structure can be addressed by name: <fs>-fieldname. The structured field symbol points initially to the work area wa specified after DEFAULT.
The work area wa must be at least as long as the structure s. If s contains fields of the type I or F, wa should have the structure s or at least begin in that way, since otherwise alignment problems may occur.
Example
Address components of the flight bookings table SBOOK using a field symbol:
DATA SBOOK_WA LIKE SBOOK.
FIELD-SYMBOLS <SB> STRUCTURE SBOOK
DEFAULT SBOOK_WA.
WRITE: <SB>-BOOKID, <SB>-FLDATE.
<b>Reward points for useful Answers</b>
Regards
Anji

Typeahead problem using Endeca

Hi all,
We are exploring the type ahead using Endeca option.
We started with the reference App (typeahead.xq) and were able to set it up.The challenge we are facing is:
We are getting the suggestions only after typing the entire search term.
For example:If we type "North" the suggestions North Goa,North America,North Carolina are coming up only after typing the entire word "North".
We would expect those to come after the letters Nor are typed or No are typed.I assume we are doing a match mode all hence this problem.
Can anyone guide us for achieving the wild card suggestions instead of getting the result after typing the whole word?
Saludos
Kartheek

Hi Kartheek,
There are a couple of things to check here:
1. Enable Dimensions for wildcard search by opening the project in Developer Studio, then open the Dimensions from the Project menu and you will see a button up top called "Configure Search". Open this and check the "Enable for wildcard search checkbox in the dialog box. You must re-run the baseline update.
2. Ensure that you are encapsulating the search term(s) inside the asterisk symbol when submitting the search to the Endeca engine. I can't remember but this may already be in the typahead.xq module.
Andy

How to populate one internal table from another using field symbols

Hi Gurus,
I have a problem. I have to populate one internal table (sructure t_otput) from another internal table (sructure t_from) using field symbol.
Structure for from table.
types: begin of t_from,
         year(4) type c,
         ww(2) type c,
         site type marc-werks,
         demand type i,
       end of t_from.
Structure for output table.
types: begin of t_display,
         title(30),
         WW1(10),
         WW2(10),
         WW3(10),
       end of t_display.
The from table looks like this:
Year | WW | Site | Demand
2005 | 1 | OR1 | 12.00
2005 | 2 | OR1 | 13.00
2005 | 3 | OR1 | 14.00
The display table which has to be populated should look like this:
Title | WW1   | WW2   | WW3
OR1    |       |       |
Demand | 12.00 | 13.00 | 14.00
How to populate display table using field symbol?
Please give code snippets
Thanks,
Gopal

Gopal,
Here is the code, however I am not vary clear about the ORG1 and Demand display that you have shown in the display. I am sure with this code it should not be a big deal to tweak in whatever manner you want.
TABLES : marc.
TYPES: BEGIN OF type_display,
title(30),
ww1(10),
ww2(10),
ww3(10),
END OF type_display.
TYPES: BEGIN OF type_from,
year(4) TYPE c,
ww(2) TYPE c,
site TYPE marc-werks,
demand TYPE i,
END OF type_from.
data : t_from type table of type_from,
       t_display type table of type_display.
field-symbols : <fs_from> type type_from,
                <fs_display> type type_display.
data : wa_from type type_From,
       wa_display type type_display.
wa_from-year = '2005'.
wa_from-ww   = '1'.
wa_from-site = 'OR1'.
wa_from-demand = '12.00'.
insert wa_from into table t_from.
wa_from-year = '2005'.
wa_from-ww   = '2'.
wa_from-site = 'OR1'.
wa_from-demand = '13.00'.
insert wa_from into table t_from.
wa_from-year = '2005'.
wa_from-ww   = '3'.
wa_from-site = 'OR1'.
wa_from-demand = '14.00'.
insert wa_from into table t_from.
data : variable(3) type c.
field-symbols : <fs_any> type any.
break-point.
Loop at t_from assigning <fs_from>.
variable = 'WW'.
wa_display-title = <fs_from>-site.
concatenate variable <fs_from>-ww into variable.
assign component variable of structure wa_display to <fs_any>.
<fs_any> = <fs_from>-demand.
endloop.
append wa_display to t_display.
clear wa_display.
loop at t_display assigning <Fs_display>.
write :/ <fs_display>.
endloop.
Note : Please award points if this helps you.
Regards,
Ravi

Problem using standard libraries in C++ class

Hi
I am new to JNI. I am having problems using standard C++ library.
My java code looks like
public class JavaSide {
public native void sayHello();
static {
System.loadLibrary("NativeSideImpl");
public static void main(String[] args) {
JavaSide app = new JavaSide();
app.sayHello();
and My NativeSideImpl.cpp code is
#include <stdio.h>
#include "JavaSide.h"
JNIEXPORT void JNICALL Java_JavaSide_sayHello
(JNIEnv *env, jobject obj)
cout<<" Hello";
I am compiling this on solaris 5.8 using the following command
CC -G -Kpic -I/usr/java/include -I/usr/java/include/solaris NativeSideImpl.cpp -o libNativeSideImpl.so
when I run my java program using
java JavaSide
I get the following exception
Exception in thread "main" java.lang.UnsatisfiedLinkError: /home/oracle/temp/libhello.so: ld.so.1: java: fatal: relocation error: file /home/oracle/temp/libhello.so: symbol __1cDstdEcout_: referenced symbol not found
at java.lang.ClassLoader$NativeLibrary.load(Native Method)
at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1473)
at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1397)
at java.lang.Runtime.loadLibrary0(Runtime.java:788)
at java.lang.System.loadLibrary(System.java:832)
at HelloWorld.<clinit>(HelloWorld.java:6)
The program works if I replace cout with printf() .
My LD_LIBRARY_PATH does include the path where of the C++ standard libraries.
Any help would be much appreciated
Thanks in advance..

Well, cout was just a a simple example. I was having problems with using the std C++ libraries, e.g ostringstream . and likes .
I tried using the -lCstd in the compile option and it worked.

Data Maintain in a table form another table....using field symbols.

Hi,
I am using dynamic table concepts.I am using field symbols.I need to maintain two tables of similar structure.
when i append data it will enter into both tables.when i unassign first table and reassign it ,i am getting back that data again into first table ..how to slve this problem.i need to start first table as fresh table and second table contain copy of the first table.

Hi,
maybe you should clarify your problem a bit more by pasting some code and try to explain it a bit more in detail.
Roy

Perform setting OOP ALV for multiple reports using Field Symbols

Hi, Abapers ... i try to write a programme which using ONE oop ALV but 2 different structure internal table. the last result should be 2 radio button. first button is r_wbs and 2ns r_kpi. r_wbs will display 4 column answer and r_kpi will display 10 columns answer with different column name. i successfully implemented using FIELDS SYMBOLS but the problems i failed to perform customized setting forALV (report's tittle, column name, different layout etc) for 2 different reports. this is the programme. Please Give Opinion, simple example will be more helpful. Thanks You Very Much
*&this report experimental how to print into ONE alv
*&with 2 diffrent structure internal table
REPORT zfiroopalv.
SELECTION-SCREEN BEGIN OF BLOCK mode WITH FRAME TITLE text-002.
PARAMETERS r_wbs RADIOBUTTON GROUP mode DEFAULT 'X'.
PARAMETERS r_kpi RADIOBUTTON GROUP mode.
SELECTION-SCREEN END OF BLOCK mode.
CLASS lcl_main DEFINITION.
PUBLIC SECTION.
CLASS-DATA: md_wbs TYPE c LENGTH 1.
METHODS: process,
         write.
DATA: mdo_data TYPE REF TO data.
TYPES: BEGIN OF st_wbs,
rsnum TYPE zmeime002a-rsnum,
rspos TYPE zmeime002a-rspos,
a TYPE zmmgitab01-menge,
b TYPE zmeime002a-bdmng,
c TYPE zmeime002a-bdmng,
d TYPE zmeime002a-bdmng,
e TYPE zmeime002a-bdmng,
f TYPE zmmgitab01-menge,
g TYPE zmmgitab01-menge,
END OF st_wbs.
TYPES: BEGIN OF st_kpi,
regio TYPE zmeime002a-regio,
gsber TYPE zmeime002a-gsber,
gtext TYPE zmeime002a-gtext,
x TYPE zmmgitab01-menge,
y TYPE zmmgitab01-menge,
z TYPE zmmgitab01-menge,
END OF st_kpi.
CLASS-DATA: it_wbs TYPE TABLE OF st_wbs,
            wa_wbs LIKE LINE OF it_wbs.
CLASS-DATA: it_kpi TYPE TABLE OF st_kpi,
            wa_kpi LIKE LINE OF it_kpi.
PRIVATE SECTION.
DATA: set_display_setting TYPE REF TO cl_salv_table.
DATA: display_settings TYPE REF TO cl_salv_display_settings.
DATA: salv_table TYPE REF TO cl_salv_table.
DATA: error TYPE REF TO cx_root.
DATA: errtext TYPE string.
ENDCLASS.
CLASS lcl_kpi DEFINITION INHERITING FROM lcl_main.
PUBLIC SECTION.
METHODS: process_kpi.
PRIVATE SECTION.
ENDCLASS.
* C.L.A.S.S lcl_main D.E.F.I.N.I.T.I.O.N
CLASS lcl_wbs DEFINITION INHERITING FROM lcl_main.
PUBLIC SECTION.
METHODS: process_wbs.
PRIVATE SECTION.
ENDCLASS.
* m.a.i.n. .p.r.o.g.r.a.m.
START-OF-SELECTION.
DATA: o_main TYPE REF TO lcl_main.
DATA: p_wbs TYPE c.
CREATE OBJECT o_main.
CASE 'X'.
WHEN r_wbs.
      o_main->md_wbs = 'X'.
WHEN r_kpi.
      o_main->md_wbs = ' '.
ENDCASE.
o_main->process( ).
o_main->write( ).
CLASS lcl_main IMPLEMENTATION.
*ENDMETHOD.
METHOD process. " NOTE: public method
DATA: o_main TYPE REF TO lcl_main,
      o_wbs TYPE REF TO lcl_wbs,
      o_kpi TYPE REF TO lcl_kpi.
CREATE OBJECT: o_wbs,o_kpi.
IF ( me->md_wbs = 'X' ).
      CALL METHOD o_wbs->process_wbs( ). " NOTE: private method
      GET REFERENCE OF me->it_wbs INTO me->mdo_data.
ELSE.
      CALL METHOD o_kpi->process_kpi( ). " NOTE: private method
      GET REFERENCE OF me->it_kpi INTO me->mdo_data.
ENDIF.
ENDMETHOD.
METHOD write.
FIELD-SYMBOLS:
<lt_outtab>    TYPE table.
ASSIGN me->mdo_data->* TO <lt_outtab>.
cl_salv_table=>factory(
EXPORTING
list_display = if_salv_c_bool_sap=>false
IMPORTING
r_salv_table = salv_table
CHANGING
t_table = <lt_outtab>
salv_table->display( ).
ENDMETHOD.
ENDCLASS.
CLASS lcl_kpi IMPLEMENTATION.
METHOD process_kpi.
*********** run some select statement into it_kpi*******
ENDMETHOD.
ENDCLASS.
CLASS lcl_wbs IMPLEMENTATION.
METHOD process_wbs.
*********** run some select statement into it_wbs*******
ENDMETHOD.
ENDCLASS.

Hi,
I had similar requirement wherein I was supposed to display different data using 2 different internal tables on a subscreen area.
The screen consists of two parts: 1) selection-screen with few input fields and two buttons 2) Subscreen area where the report need to be displayed. This report is displayed based on the button that the user is selecting. For this I have done the following things:
1. Capture the sy-ucomm when user is clicking on any of the two buttons in PAI. Then perform data fetch operation.
         MODULE USER_COMMAND_9003 INPUT.
             CASE OK_CODE.
                 WHEN 'DETAIL'.
                   GV_RPT = OK_CODE.
                   PERFORM F_GET_DETAIL_DATA.
                 WHEN 'REPORT'.
                   GV_RPT = OK_CODE.
                   PERFORM F_GET_REPT_DATA.
               ENDCASE.
         ENDMODULE.                 " USER_COMMAND_9003 INPUT
2. Declare two different ALV's with the fieldcat similar to 2 internal tables respectively. Use the above sy-ucomm PBO to call appropriate ALV.
         MODULE DISPLAY_ALV OUTPUT.
           IF GV_RPT EQ 'DETAIL'.
             PERFORM F_FIELDCAT_DETAIL.
             PERFORM F_LAYOUT_DETAIL.
             PERFORM F_EXCLUDE_TOOLBAR_DETAIL.
             PERFORM F_DISPLAY_ALV_DETAIL.
           ELSEIF GV_RPT EQ 'REPORT'.
             PERFORM F_FIELDCAT_REPT.
             PERFORM F_LAYOUT_REPT.
             PERFORM F_EXCLUDE_TOOLBAR_REPT.
             PERFORM F_DISPLAY_ALV_REPT.
           ENDIF.
         ENDMODULE.                 " DISPLAY_ALV OUTPUT
3. Before displaying ALV you need to free the container and ALV.
FORM F_DISPLAY_ALV_DETAIL .
IF GC_CONTAINER_ES IS NOT INITIAL.
    CALL METHOD GC_CONTAINER_ES->FREE
      EXCEPTIONS
        CNTL_ERROR        = 1
        CNTL_SYSTEM_ERROR = 2
        OTHERS            = 3.
    IF SY-SUBRC <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
               WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    ENDIF.
ENDIF.
IF GC_ALV_GRID_ES IS NOT INITIAL.
    CALL METHOD GC_ALV_GRID_ES->FREE
      EXCEPTIONS
        CNTL_ERROR        = 1
        CNTL_SYSTEM_ERROR = 2
        OTHERS            = 3.
    IF SY-SUBRC <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
               WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    ENDIF.
ENDIF.
IF GC_CONTAINER_TB IS NOT INITIAL.
    CALL METHOD GC_CONTAINER_TB->FREE
      EXCEPTIONS
        CNTL_ERROR        = 1
        CNTL_SYSTEM_ERROR = 2
        OTHERS            = 3.
    IF SY-SUBRC <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
               WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    ENDIF.
ENDIF.
IF GC_ALV_GRID_TB IS NOT INITIAL.
    CALL METHOD GC_ALV_GRID_TB->FREE
      EXCEPTIONS
        CNTL_ERROR        = 1
        CNTL_SYSTEM_ERROR = 2
        OTHERS            = 3.
    IF SY-SUBRC <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
               WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    ENDIF.
ENDIF.
CREATE OBJECT GC_CONTAINER_ES
    EXPORTING
      CONTAINER_NAME              = 'CC_9003'
    EXCEPTIONS
      CNTL_ERROR                  = 1
      CNTL_SYSTEM_ERROR           = 2
      CREATE_ERROR                = 3
      LIFETIME_ERROR              = 4
      LIFETIME_DYNPRO_DYNPRO_LINK = 5
      OTHERS                      = 6.
CREATE OBJECT GC_ALV_GRID_ES
    EXPORTING
      I_PARENT          = GC_CONTAINER_ES
    EXCEPTIONS
      ERROR_CNTL_CREATE = 1
      ERROR_CNTL_INIT   = 2
      ERROR_CNTL_LINK   = 3
      ERROR_DP_CREATE   = 4
      OTHERS            = 5.
CALL METHOD GC_ALV_GRID_ES->SET_TABLE_FOR_FIRST_DISPLAY
    EXPORTING
      IS_LAYOUT                     = GS_LAYOUT_ES
      IT_TOOLBAR_EXCLUDING          = GT_TOOLBAR_ES
    CHANGING
      IT_OUTTAB                     = GT_ES_REPT
      IT_FIELDCATALOG               = GT_FIELDCAT_ES
    EXCEPTIONS
      INVALID_PARAMETER_COMBINATION = 1
      PROGRAM_ERROR                 = 2
      TOO_MANY_LINES                = 3
      OTHERS                        = 4.
ENDFORM.                    " F_DISPLAY_ALV_DETAIL
Similarly define the FORM F_DISPLAY_ALV_REPT.
Hope this will be useful for you. If you have any more queries let me know.

Problem using asterisk symbol (*) in Translation Rule

Similar Messages

Maybe you are looking for