Problem w/ Color on Second Output - TV

I have a GeForceFX5600XT-TD128 video card. I just installed the latest set of drivers from NVidia - 56.72.
I am trying to use the little 4 pin Video Out connector to connect to a TV in order to record to VideoTape a powerpoint presentation. Anyway. I have the connector supplied with the card to an RCA cord (about 6' long) connected to my TV's video input.
I can get the video card to go into "clone mode". What I see on the Monitor is what I see on the TV screen ... Except the TV screen is NOT in Color.
Any suggestions?
Please help

So it works ok on the primary TV. I authorized it on the second TV and it seemed to authorize fine. But when I try to watch a show, I get the spinning wheel before it says I can't access at this time, try again later. It's been over a week now with the same result each time. Unfortunately, I can't call HBO support, because reasons. Thanks for any help.

Similar Messages

Problem adjusting color then printing with CS3 on Epson R300

I am running on a Dell quad core system with 3MB of ram and Vista 32bit and CS3. I am unable to alter the color of the image that prints. For example, if I reduce the saturation all the way down to get a B&W and print I get a print that looks like the original unaltered color print. Even if I save the B&W print and reload it back into CS3 and print I get the original color print.
As best I can tell this problem started when I loaded CS3 on top of CS. I tried printing using CS and CaptureNX and have the same problem.
Anyone have any ideas about what's causing this?

Chris, sorry for some off-topic comments,
Al, I'm referring to
James King
Engineering color at Adobe,
chapter 15 in
Ph.Green, L.Macdonald (Editors)
Colour Engineering
John Wiley & Sons, 2002
1989/1990 Adobe designed the PostScript Level 2
color concept with CIE-based device independent-colors.
Apple's ColorSync system development was started 1991
and announced 1993.
The International Color Consortium ICC was started in
spring 1993.
From these facts it is obvious that Adobe's concept
came very early. There was no need to change it, but some
features were added later.
Dr King emphasizes the importance of handling black in
CMYK workflows. The ICC had overlooked this - profile
to profile conversions in CMYK destroy the original black
generation. There are other design concepts for ICC profiles
which are IMO rather doubtful: mainly the very complex
number and data format system and the definition of the
location of modules by byte offsets. Compared to these
structures, PostScript is simple and readable (ASCII).
All this lead me to the conclusion that PostScript color
management is probably not bad.
'Adobe' is not the same as 'PostScript':
I found, that host based Acrobat CMM for the OKI printer
C9600 lead to severe bugs for the black generation.
This is described here in chapter 1:
http://www.fho-emden.de/~hoffmann/oki-ps-28082005.pdf
Then I changed he strategy systematically: everything
printer based by PostScript. ICC profiles are downloaded
to the harddisk. Color Rendering Dictionaries (output)
and CSAs (input) are calculated in the printer.
If the printer is equipped with genuine Adobe PostScript 3
('level' no more used) then one can expect that it works
correctly. It is OK for Acrobat and PageMaker but not
for InDesign (tested for CS2 and Acrobat7).
Best regards --Gernot Hoffmann

Problem in customizations after Issue Output of a Billing Document (VF02)

Dear Friends,
I am facing some problem while I do repeat output of a Billing Transaction. (VF02->GoTo->Header->Output). There are some customizations done in our system that whenever an Output is processed in our system, an xml file should be created and placed on application server (Which would then be printed in some Legacy system).
The custmizations for this has been done SPRO -> Sales and Distribution -> Billing Documents -> Invoice Lists ->Maintain Output for Invoice Lists -> Output Type.
Now my problem is that XML file creation program works in the Dialog mode and I am able to create the XML file and make an entry of this file in a Z table as per my program logic.
But when the processing is automatically through some files coming from application server, some of the files are missed. I want to figure out under which conditions my program to create XML file fails.
I tried debugging this program by puttinga hard coded break-point as well but the control does not stops there.
Could any one please help me how can we debug the program in such scenario.
Thanks a Lot for your kind help!!!
Regards,
Lalit Kabra

There was some issue in the RFC setup of our system because of which when fies were processed in bulk, some of them were missed out. It was like connection issue. Hence I did not put the soln here as I could not get the answer of this problem by doing some thing in ABAP.
Apologies for the same.
Regds,
Lalit

I have a problem with color prints from photoshop elements 12. The pictures are too light and with strange colors. I have a Canon pixma mg615I0 printer and use mac os X yosemite. The pictures are taken with a coanon eos 550d in the color space sRGB. I hav

Hi
I have a problem with color prints from photoshop elements 12. The pictures are too light and with strange colors. I have a Canon pixma mg615I0 printer and use mac os X yosemite. The pictures are taken with a coanon eos 550d in the color space sRGB. I have followed adobes recommendations and have tried both letting the printer respektive photoshop manage the colors. But nothing works. I see that there are different opinions about which is best to do so I tried both. I have the latest printer driver installed. Can anyone help me with this?

Do the following:
Print a test page from the printer. Perhaps the print head needs cleaning via its maintenance facility.
Let the printer manage colors, not PSE
Calibrate the monitor

Problem in displaying Alv grid output using oops........

hi,
i have two problems in displaying ALV grid output Using Oops.
1) How to modify the fieldcatalog after we getting a field catalog using general FM.
2) initialy it is displaying 13 fields but there are 63 fields .
eventhough we chage the layout to 63 fields it is displaying only 13 fields , these 13 fields may be different based on our selection but count of displayed fileds are same . how can display 63 fields at a time .

Hi,
You can chnage using below code:
loop at gt_fieldcat.
if <gt_fieldcat-field_name> = 'FIELDNAME'.
endif.
modify gt_fieldcat.
clear gt_fieldcat.
endloop.
Make sure that all the field should not have no_out = 'X' and tech = 'X'.
Thanks,
Sriram Ponna.

Problems with color matching when printing...

Hi, I work for a small family business in the P.O.P. industry. We currently have myself and one other designer, we both take illustrator files that have come from the graphic design firm that we contract with and get them ready to print on our Vutek QS3200. However ever since acquiring the printer we have begun to run into problems with the colors when printing. When the files are exported off of my computer, I use either .tif or .pdf files, they print as they should, the colors seem to match the proof and everything goes smoothly. However when the other designer exports a file, he tends to do mainly pdfs, the colors tend to be extremely different from where we want them. Also we will get very strange results, such as yesterday he kept getting a faint yellow 1/2" border around his prints. After I believe 3+ hours of him trying, I was given the original CD and instructed to try. After 15-20 minutes of making the changes that we needed to make (adding a new price point) and ripping, mine printed perfectly.
We both use Macs, both have CS3 Design standard, only differences between the computers are mine is newer and a bit faster, and I'm running OS 10.5.6 and he has 10.4. He has also at some point loaded various color profiles, whereas my CS package is just whatever the default is when I loaded it. When we were being trained he grabbed the color profile off of the Colorburst RIP server and loaded onto his computer, plus I believe he has a couple for freelancing purposes on there as well. My thought is that these profiles are somehow corrupting the files that are going through that computer, but I honestly am lost with it at the moment. He believes the problem lies within the fact that he does not have the newer OS, I honestly cannot see that as having any effect on this at all. I was wondering if anyone has run into any similar problems, or if anyone might have any advice on this issue? I would really like to be able to solve this, as I was hired to do mainly structural design for the P.O.P. and I'm having to put in a lot of overtime to get my work done along with the additional work that I'm having to do.
Thanks for your time

I've got a few years experience calibrating large format printers. First, the Yellow sounds like a file problem. I used to work with two workstations, one PC ( RIP station ), and one Mac ( file prep station ). I tend to agree with you in that the OS is probably not the problem. But, any Colorburst profiles should remain in the RIP, not in the originator application. My workflow consisted of creating EPS files that were based on established color settings in their given applications ( i.e., Illustrator, Photoshop ) which were interpreted by the RIP which had it's own calibrated profile ( perhaps more than one based on how many different substrates were being used ). Your partner may be complicating things by incorporating a RIP profile prematurely. If there are deviations big enough to be noticed, there has to be something in the application color settings that is causing some type of corruption. This could lead back to the operating system, but I would think it lies somewhere in Bridge or the application color settings. Start there. You should seriously consider implementing a calibration system if you do not have one already. Another slight possibility is the driver's ability to interpret files coming out of Leopard vs. files coming out of Tiger. It may benefit you both to be in the same operating system dynamics, using the same driver versions and RIP profiles. At the very least, match everything that is currently working successfully and put them on both machines. If there is still a noticeable problem in color matching, then something is seriously wrong and you should call in a prepress profiling expert. Hope this helps.

Problems with colors running CS4 and W7.

Hey everyone.
I'm having some MASSIVE problems with colors on my system.
Windows 7 Prof 64bit
Photoshop CS4 64bit
6g Ram
1T hard drive
Nvidia GeForce 9800 GTX+
Dell SE198WFP Monitor
The system itself is a Dell Inspiron 530 that I put into a Black Widow V9 gaming tower.
Here is an example of the issue I'm having:
http://findae.deviantart.com/art/Converge-101214480
http://i38.tinypic.com/bjcymr.jpg
The top image is a (admittedly old and crappy, but it shows the problem) photo that I had previously edited and put in my portfolio. The tinypic below is the result of copying that photo from the portfolio, pasting it into photoshop, and then saving it into a jpg. As you can see, the transitions between colors and the contrast are a complete mess.
Thing is, my hard drive recently quit on me, and I had to install the operating system and such on a new drive. I remember having this problem with the system when I first had it, but it either went away on its own or I fixed it somehow before. Now I can't remember for the life of me how I got rid of the problem, and I certainly don't know what the problem is in the first place. I'm tempted to think it may not be photoshop itself, but the problem seems to be especially bad when I'm working with photos.
Anyone have any idea what the problem might be and how to solve it?
Edit: I also noticed it when viewing http://findae.deviantart.com/gallery/#/d1hni37 in firefox, whereas the other photo appeared to be ok before I copied and pasted it. It has extremely obvious lines of green and orange in the transition from light skin tone to dark skin tone. Annoyingly enough, this doesn't show up in the thumbnail within my gallery at all, only when I click on the thumbnail and see the fullsize image. Extremely frustrating.
Here's another good look at the problem while selecting a color in photoshop: http://i37.tinypic.com/2h6t7gh.jpg All I did was screenshot it a few times, and it deteriorated to that point.

Screen glitches like color blocks appearing where they shouldn't could indicate a problem with your video drivers.
Go to the nVidia site and see if they've released any updated drivers; people often report that updated drivers are correcting current problems with Photoshop.
http://www.nvidia.com/object/win7-winvista-64bit-258.96-whql-driver.html
Note the recent (3 weeks ago) release.
-Noel

Problem with colors showing in PE10

Is there a known problem with color in Elements 10?
I have a gif that when opened in paint shows the light blue color correctly but in PSE10 shows as a buff color.
Red, yellow and blue seem about right.
It doesnt matter if it is the gif or the psd file the color showns the same in PSE10.
Is there a setting or could something be corrupted.

Bump.
I have uninstalled and reinstalled Elements and get the same result.
Is there a way to adjust the colors represented in Elements 10?

4400F scanner has problems with color slides

About six years after buying the 4400F scanner, I finally opened it today in order to start scanning a lot of color slides going back more than 40 years. It seems as if the software (or the scanner itself) doesn't know where one slide ends and the next one begins. The slide holder accommodates up to four slides. Using several methods of scanning permitted by the software, I obtain either three or five JPEG scans. In the case of three, the images are properly centered--only the final one is missing. In the case of five, the images are all off-center.
Has anyone had a similar problem with this unit and the software when scanning slides?
EG

I've got a few years experience calibrating large format printers. First, the Yellow sounds like a file problem. I used to work with two workstations, one PC ( RIP station ), and one Mac ( file prep station ). I tend to agree with you in that the OS is probably not the problem. But, any Colorburst profiles should remain in the RIP, not in the originator application. My workflow consisted of creating EPS files that were based on established color settings in their given applications ( i.e., Illustrator, Photoshop ) which were interpreted by the RIP which had it's own calibrated profile ( perhaps more than one based on how many different substrates were being used ). Your partner may be complicating things by incorporating a RIP profile prematurely. If there are deviations big enough to be noticed, there has to be something in the application color settings that is causing some type of corruption. This could lead back to the operating system, but I would think it lies somewhere in Bridge or the application color settings. Start there. You should seriously consider implementing a calibration system if you do not have one already. Another slight possibility is the driver's ability to interpret files coming out of Leopard vs. files coming out of Tiger. It may benefit you both to be in the same operating system dynamics, using the same driver versions and RIP profiles. At the very least, match everything that is currently working successfully and put them on both machines. If there is still a noticeable problem in color matching, then something is seriously wrong and you should call in a prepress profiling expert. Hope this helps.

Strange problem with color measure in Mac.

Hello, I am having a strange problem with color measure in Mac. For example i create a gradient in Photoshop from color 200 200 200 to color 240 240 240. When i measure the color of the gradient with the color measure tool of Photoshop or with the built in OS X color measure tool the measured color is from 200 199 197 to 240 240 238. I have measured the same gradient with Photoshop for PC and the values are OK (the same values that i create).
I dont know what is the problem, but i belive that the colors that i create would be the same that i measure after creating them, and also the same values between Mac and PC. I will appreciate it a lot any help or information that you could give me that helps me to understand what is happening here.
Thank you for your time
Marcelo.

Yep you got it, proof as monitor basicaly strips out any profiling and just delivers it straight.
is there any way to make the OS X color measure tool to measure the original color values
You mean the document colors - No, like I said photoshop is filtering your image through document profile, proof setup and monitor profile. Why do you want to use Digital color meter anyway for this?
i dont understand what is the point to measure color values that will change every time a calibrate my monitor.
Because color values are 'bigger' than whats on your monitor. Your monitor (via photoshop) is only doing the best it can to display those values - which can be anything from LAB colors outside the gamut of your monitor - to CMYK colors. Calibrating it is the only way to allow your monitor to do this in any way accurately. (not ever really possible) Monitors have a certain gamut and are only dispays/representations of the REAL colors that a document, with a profile, holds. So there's only one good reason to measure monitor values, and that's to generate a monitor profile.

Fife days App Store not give it to me the verify code, I made I lot email adress, changed and create the new, still the same problem, and this is second one iPad that I bought this month, if not help me I don't know how to deal, thank you in advance

Fife days App Store not give it to me the verify code, I made I lot email adress, changed and created the new, still the same problem, and this is second iPad that I bought this month, if not help me I don't know how to deal, thank you in advance, maybe I will go to shop and want my money back

Do you have a technical question for us volunteer users?

Can you change the color of the output in the console?

When you run your program using NetBeans the color of the output in the console window is black. Is there any way to change the color of the output to say blue?

Hi AJL,
There is no way to color rows of the table control in a SUDialog. You could consider using the ActiveX container control and using the Microsoft ActiveX table control, which might have that functionality. Note though, that then you need to either ensure that control is always on all your client machines or make provisions for it to be installed/registered.
Brad Turpin
DIAdem Product Support Engineer
National Instruments

Java update causes problems with color printing in Mac 10.5

Had a big problem with color printing for the last two weeks. Thought the printer was broken because it would freeze and refuse to be "seen", or would generate error messages. Bought new Samsung 315, and had the SAME problem. Bought new HP CP1518ni, and had the SAME problem. Not resolved after talking to tech support at both places.
Looked for software updates around the time of the onset of printing problems. on May 15 installed "Java for Mac OS X 10.5 update" (1.0) (am running on 10.5.8). Removed the Java preferences files (com.apple.java......plist) and restarted.
Problem solved! Clearly not the printer.

Hmmm. This is about the time my printer stopped printing too. I've now had two printers in my house and had trouble with both of them. What a pain we should not have to delete updates for our stuff to work together.
Renee

HT1277 having problem setting up a second email account

I am having problems setting up a second email account on my imac. help!

In the Add Account dialog, enter the information, then hold down the option key and click Continue. Finish setting up the account manually.

Can I fix the alignment problems my Color LaserJet CP1518ni is having? The red does not line up.

Can I fix the alignment problems my Color LaserJet CP1518ni is having? The red does not line up. I have installed the latest updates, etc. Calibrating does not help. The printer is only a few years old. What gives?
This question was solved.
View Solution.

Please be aware that this forum is a peer to peer support forum, it is not a direct link to HP support.
I have a similar issue with a Laserjet cp1525nw, it was mostly corrected by removing and reseating the toner cartridges.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Problem w/ Color on Second Output - TV

Similar Messages

Maybe you are looking for