Problem when mounting tomcat server for upgrading ACS

Hi:
I've downloaded the Appliance Management package for 4.1.1.23 version. Once I extract all archives I execute the autorun.bat file. The problem is that the tomcat server doesn't work properly, continuously appears a message error:
INFO: WebServer not ready or not fully initialized -- testing again...
Which can be the problem?,
Many Thanks

Upgrading the Cisco Secure ACS Solution Engine typically involves the following three steps:
1. Obtain the upgrade package from Cisco Systems and load it onto a distribution server in your network. This can be done either by employing an upgrade CD or downloading the upgrade package from Cisco.com.
2. Load the upgrade image onto the Cisco Secure ACS Solution Engine from the distribution server on your network. You can do this either from within the HTML interface, or from the serial console. The Cisco Secure ACS Solution Engine verifies the files transferred to ensure that they have not been corrupted. For more information on performing this step from the HTML interface, see the below URL:
http://www.cisco.com/en/US/products/sw/secursw/ps5338/products_user_guide_book09186a0080204be1.html
3. Finally, apply the Cisco Secure ACS Solution Engine system upgrade. You can do this either from within the HTML interface, or from the serial console. For more information, see:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/3.3/installation/guide/appliance/admap.html#wp1048998

Similar Messages

  • Re: Using already running Tomcat server for development.

    Hi Nick,
    Yes, you can use existing Tomcat Server for debugging app developed with
    NitroX. And you can refer to Help > Help Contents > NitroX User Guide >
    NitroX Tour > Running and debugging the application.
    We do support Tomcat 4.0.x to Tomcat 5.0.x. If you need any further
    assistance please get back to us.
    Thanks
    M7 Support
    "Nick Mulder" <[email protected]> wrote in message
    news:41d9f379$[email protected]..
    Sorry if this has been covered anywhere else.Just wondering if you can use an existing tomcat server for debugging
    webapps being developed in NitroX. I have a non dedicated server a
    development server. Up until purchasing NitroX I have been using ant build
    files to compile and re-deploy my apps into the running tomcat server.
    Just wondering if I can do something similar thru NitroX and Eclipse.
    Forgive me if I am missing something obvious, but I am new to eclipse.
    Thanks,
    Nick Mulder

    Take a look at these links: http://plato.acadiau.ca/courses/comp/dsilver/2513/EclipseAndTomcatTutorial/
    http://www.keyboardsamurais.de/2004/01/15/tomcat_tutorial_helloworld_for_complete_fools_-_english/
    http://www-128.ibm.com/developerworks/opensource/library/os-ectom/?ca=dgr-lnxw16EclipsTomcat
    I've found going through tutorials is a proven, quick way of getting up to speed with new tools and configurations.
    HTH,
    James

  • Using already running Tomcat server for development.

    Sorry if this has been covered anywhere else.
    Just wondering if you can use an existing tomcat server for debugging
    webapps being developed in NitroX. I have a non dedicated server a
    development server. Up until purchasing NitroX I have been using ant build
    files to compile and re-deploy my apps into the running tomcat server. Just
    wondering if I can do something similar thru NitroX and Eclipse. Forgive me
    if I am missing something obvious, but I am new to eclipse.
    Thanks,
    Nick Mulder

    Take a look at these links: http://plato.acadiau.ca/courses/comp/dsilver/2513/EclipseAndTomcatTutorial/
    http://www.keyboardsamurais.de/2004/01/15/tomcat_tutorial_helloworld_for_complete_fools_-_english/
    http://www-128.ibm.com/developerworks/opensource/library/os-ectom/?ca=dgr-lnxw16EclipsTomcat
    I've found going through tutorials is a proven, quick way of getting up to speed with new tools and configurations.
    HTH,
    James

  • I use captivate 8, the problem when i make app for android. the sound not heard. i use android4.4. how i do?

    i use captivate 8, the problem when i make app for android. the sound not heard.
    i use android4.4. how i do?
    i use phonegap online.
    thank you

    Yes I do spend a lot of time in China but I have had problems in other countires as well.  I am in China right now.
    I have two Gmail accounts and one Cox account.  Cox is my intranet provider back home.  I have had problems with all three accounts. 
    I have tried several outgoing port settings.  993, 995 465, 587 are some that I can remember trying.
    Sometimes my accounts will go offline without me doing anything.  This is all a mystery to me.  I don't have any idea why I have trouble like this.  A few minutes ago I changed my Cox account outgoing port and took the account on line and I got my incoming email but when I tried to forward an email that I got it would not go out. 
    Any ideas you have would be helpful.

  • I have Problem when installing ADF Runime for Application Server

    Hi All,
    I have Application Server 10.1.2.0.2 and Jdeveloper 10.1.3.2
    I followed the next steps
    1 - in Application Server I created OC4J instance named app1
    2- I Stoped all infrastucure and middle-tier of Application Server
    3- in Jdeveloper I installed ADF Runime for Application Server
    by the next steps :-
    Application server home directory : OraHome_2
    oc4j instane name : app1
    and I selected: install a new version of ADF Runtime 10.1.3.40.66
    after that I got a jdeveloper sussceeful install ADF Runtime message
    5- when entering this command below to start Application server
    it gives me an error message
    C:\OraHome_2\opmn\bin>opmnctl startall
    opmnctl: starting opmn and all managed processes...
    ======================================
    opmn id=royal:6201
    0 of 1 processes started.
    ias-instance id=midd_admin.royal
    +++++++++++++++++++++++++++++++++++++++
    ias-component/process-type/process-set:
    OC4J/apptest1/default_island
    Error
    --> Process (pid=3808)
    failed to start a managed process after the maximum retry limit
    Log:
    C:\OraHome_2\opmn\logs\OC4J~apptest1~default_island~1
    any soluation to solve this error when starting Appliction server ?
    thanks

    This is the error message in log file
    07/06/14 05:51:55 Start process
    07/06/14 05:51:59 Error starting ORMI-Server. Unable to bind socket: Address already in use: JVM_Bind
    07/06/14 05:52:01 Auto-deploying file:/C:/OraHome_2/j2ee/home/default-web-app/ (New server version detected)...
    07/06/14 05:52:01 Auto-deploying file:/C:/OraHome_2/j2ee/home/applications/dms/ (New server version detected)...
    07/06/14 05:52:03 Oracle Application Server Containers for J2EE 10g (10.1.2.0.2) initialized
    07/06/14 05:52:03 java.lang.NullPointerException
    07/06/14 05:52:03      at com.evermind.server.rmi.RMIServer.run(RMIServer.java:464)
    07/06/14 05:52:03      at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:186)
    07/06/14 05:52:03      at java.lang.Thread.run(Thread.java:534)
    07/06/14 05:53:13 Notification ==> Application Deployer for Test8 STARTS [ 2007-06-14T05:53:13.593PDT ]
    thanks for your care

  • Problem in installation tomcat server 4.1

    Hi everybody,
    I am not sure if i have entered the correct forum for highlighting problems of Tomcat server 4.1, but anyway I need an answer.
    My system is running on win 98.
    I downloaded the zip version from apache.org and created the java_home and catalina_home path in the autoexec.bat.
    When I am running the startup.bat file, it gives me some output in one window like :
         using catalina_base=d:\apache\tomcat
         using catalina_home=d:\apache\tomcat
         using catalina_tmpdir=d:\apache\tomcat\temp
         using java_home=c:\jdk1.2
    The name of this window is Finished-startup.
    After running this bat another window gets fired, with the heading as java, and this window vanishes immediately. I need some ideas as to what should be done.
    Just to remind, I have jdk1.2 on my system. Do I have to upgrade to jdk 1.4. Does Tomcat 4.1 need the latest version of jdk.
    Thanks n regards,
    Sajiv, Chennai, India.

    hi,
    set java_home to java_home=c:\jdk1.2\ .I had this problem with windows XP, the window loads and vanishes. the '\' has set my problem. you can try.
    anu

  • When mount MDM server on MDM console...MDM Console hangs.

    Hi,
    when i try to mount MDM server on MDM console, MDM Console hangs and then i have to stop MDM console with task manager.
    For this i have tried with restarting  MDM server - then also issue was not resolved, then i have rebooted the server, then issue resolved.
    But rebooting the server is not permanent solution, this problem occurs everything next 3-4 days.
    Please let me know the cause and it's solution if anyone has faced the similar issue.
    ---------------Server details----------------
    SAP MDM 7.1SPS11
    OS - Suse Linux
    DB - MaxDB
    MDM Console is also SPS11
    Thanks and Regards,
    Murtaza Najmi

    Hi Murtaza,
    This may be due to the memory full issue. It is advisable to allocate appropriate memory in the RAM where server is running. Generally it will be done by the DB team or Linux/unix team. Raise this ticket to your concerned teams.
    Thanks,
    Vinoth

  • Error in re-creating RMI registry when reloading Tomcat server.

    Hi,
    I use LocateRegistry.createRegistry() in a servlet which is load-on-startup. I've unexport the registered remote object in the HttpServlet.destroy().
    But when I reload the tomcat server, such an exception ocurrs:
    java.rmi.server.ExportException: internal error: ObjID already in use
            at sun.rmi.transport.ObjectTable.putTarget(ObjectTable.java:168)
            at sun.rmi.transport.Transport.exportObject(Transport.java:69)
            at sun.rmi.transport.tcp.TCPTransport.exportObject(TCPTransport.java:190)
            at sun.rmi.transport.tcp.TCPEndpoint.exportObject(TCPEndpoint.java:382)
            at sun.rmi.transport.LiveRef.exportObject(LiveRef.java:116)
            at sun.rmi.server.UnicastServerRef.exportObject(UnicastServerRef.java:145)
            at sun.rmi.registry.RegistryImpl.setup(RegistryImpl.java:92)
            at sun.rmi.registry.RegistryImpl.<init>(RegistryImpl.java:78)
            at java.rmi.registry.LocateRegistry.createRegistry(LocateRegistry.java:164)
            at RmiUtils.rebindLocal(RmiUtils.java:86)Here is the binding code in RmiUtils.rebindLocal:
            try {
                Naming.rebind(url, rmiImpl);
            } catch (RemoteException ce) {
                if (!ru.isLocalhost()) {
                    ce.printStackTrace();
                    // cannot cache
                    return;
                } else {
                    // try to create the registry in local machine if not created
                    try {
                        LocateRegistry.createRegistry(ru.getPort());
                        Naming.rebind(url, rmiImpl);
                    } catch (RemoteException e) {
                        System.err.println("Failure in create Registry on port "
                                + ru.getPort() + ", maybe it's been created already!");
                        e.printStackTrace();// handle exception
            }Can anybody help?
    Thanks.

    Hi
    I havent code for quite a while.
    I would think that this wont work.
    The registry is created on startup (possibly init method in ur servlet) but it is never destroyed.
    You are better off starting the registry externally to ur servlet engine, and then use do a bind/rebind on startup, unbind on destroy.
    Hope this helps.

  • DNS caching problem when configuring Windows clients for SCAN

    I have a Windows 2008 R2 server running apps that connect to a RAC cluster database using the SCAN address. The SCAN address however always returns the same IP when you ping it from that server. If I flush the DNS cache I get a different address, but again the same one all the time. I believe this is caused by the fact that DNS caching is enabled on Windows by default. This has caused problems when one of the RAC nodes goes south and the cached SCAN IP is not responding. The applications lose their connections, try to reconnect, but can't because they keep using the same dead SCAN IP.
    I suggested we disable the DNS Client service on those machines so that the SCAN name correctly cycles through the addresses but the Windows admin says not to do this. Is there a documented practice somewhere that this is OK to do for Windows RAC clients? Or is there a way to disable caching just on the SCAN name but leave it enabled from every other host name?
    TIA

    What happened was the SCAN VIP did not fail over. The node VIP did not fail over. The database instance was running but I could not connect to it even locally as sysdba. I got the message "protocol adapter error". This normally only occurs on Windows for local connections when either (a) the Oracle service is not running, or (b) you didn't set the ORACLE_SID variable correctly. Neither was true.
    I tried "crsctl stop crs" but it could not stop the listeners.
    I rebooted the server. During the reboot, neither the VIP no SCAN VIPs failed over. It's almost as if CRS either didnt recognize tat the other node had been shutdown, or it didn't care.
    I have never seen this happen before.
    For the record this is Oracle RAC 11.2.0.1.

  • Problem when define Value range for data element

    Dear
    When I define a new data element in ABAP Dictionary, for example, ZDATA_ELEMENT_TEST.
    I use domain ZDOMAIN_TEST.
    (Data type is DEC, the length is 10, and decimals is 2 with sign.)
    Now, I want to restrict that, user can ONLY input the value from 10 to 100.
    From ABAP course and the Internet, I switch to "Value Range" tab, and define 10 for Lower Limit, 100 for Upper Limit in Intervals section.
    And write the simple program.
    PARAMETERS test TYPE ZDATA_ELEMENT_TEST.
    WRITE: test.
    And run it.
    Line: -
    But, there is a problem.
    When I input 200 for test, the program still run and display 200 to screen without any error report or notification. The ABAP runtime system doesn't check the input value.
    I want to config for the domain that can satisfies, if the user input the wrong value (e.g: 200 in the previous case), the program will auto raise the error report, or exception, or sth like that.
    Any help is welcome.

    Hi Hanni,
    Welcome to forum.
    Try to attach key word VALUE CHECK to your PARAMETER statement.
    I.e:
    PARAMETERS test TYPE ZDATA_ELEMENT_TEST VALUE CHECK.
    Note: The addition VALUE CHECK cannot be used together with the additions AS CHECKBOX, RADIOBUTTON, or NO-DISPLAY.
    Regards,

  • Problem in setting application server for technical system

    Hi all,
       While I was trying to set the application server and message server for an already existing technical system in the SLD,I dont get the option the option for adding a new application server or changing an existing application server.Any suggestions are welcome.
    Thanks and Regards
    Jishi

    Hi,
    for changing - did you try the "Content Maintenance" on SLD Homepage? It is Subset: Landscape Description and I guess Class "BC Application Server"
    For adding a second application server - go to the technical system, scroll down and press "Add" secondary application server.
    Good luck, Holger

  • Authentication for user weblogic denied problem when starting managed serve

    Hi All,
    I have a strange situation here. I installed WLS and SOA and BAM servers. Initially I could start both WLS and SOA.
    Later I changed some files (possibly startManagedWebLogic.sh or deleted soa_server1/data/ldap/ or AdminServer/security/boot.properties), but later I remember I changed them back. I am now seeing that my WLS is starting up fine, but SOA is not. I am always getting the error:
    <Critical> <WebLogicServer> <BEA-000386> <Server subsystem failed. Reason: weblogic.security.SecurityInitializationException: Authentication for user weblogic denied
    weblogic.security.SecurityInitializationException: Authentication for user weblogic denied
    at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.doBootAuthorization(CommonSecurityServiceManagerDelegateImpl.java:965)
    at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1050)
    at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:873)
    at weblogic.security.SecurityService.start(SecurityService.java:141)
    at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
    Truncated. see log file for complete stacktrace
    Caused By: javax.security.auth.login.FailedLoginException: [Security:090303]Authentication Failed: User weblogic weblogic.security.providers.authentication.LDAPAtnDelegateException: [Security:090295]caught unexpected exception
    at weblogic.security.providers.authentication.LDAPAtnLoginModuleImpl.login(LDAPAtnLoginModuleImpl.java:251)
    at com.bea.common.security.internal.service.LoginModuleWrapper$1.run(LoginModuleWrapper.java:110)
    at com.bea.common.security.internal.service.LoginModuleWrapper.login(LoginModuleWrapper.java:106)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
    Truncated. see log file for complete stacktrace
    >
    I tried to go to admin console to change/verify the password for weblogic user, and then put plaintext password in AdminServer/security/boot.properties, then restart Adminserver. But I still cannot start SOA server.
    Could you please let me know how to resolve this issue? I do want to save my environment at this point. Many thanks.

    Hi,
    My understanding is admin user server is coming up fine but when you try to bring the soa_server1(managed instance) is not coming up due the below mentioned exception.
    If not please correct me.
    I have a few query, please give me comment on this.
    1) Admin and managed instances are running on the same box or different
    2) Did you try to reset the password from console or using weblogic.security command
    3) Did you cleared the soa_server1 temp directory(server/soa_server1/*)
    Solution-1 (If Domain running on different box)
    =============================
    1) Copy the DefaultAuthenticatorInit.ldift file from Domain_dir/Security/ to Remote machine - Domain_dir/Security/
    Note- Remote machine - take a backup of DefaultAuthenticatorInit file.
    2) Remote machine- rename or take a backup of ldap directory and boot.properties file
    /servers/soa_server1/ldap
    /servers/soa_server1/security/boot.properties.
    3) Now try to brought up the soa_server1.It will prompt you the username and password.
    Please let me know.
    Thanks,
    Rajkumar

  • Problem when creating  a tcode for maintainence view

    when i'm trying to create a tcode for maintainence view of table ,i used to fields view name: here i gave the table name;
    update : x
    now when i activated and executed the tocde the screen is showing some abnormal values in the display..this is happening in the development server..can any one help me on this..i can send the screen shot if required..thanks in advance,,
    challa

    hi,
    thank you.
    i have done the same...but here i dont want to skip the intial screen...so i didnt check that box..now comes the problem ..i can see some boxes with 'x' at the end of the paarameters..give me u r mail id i can send u the screen shot..
    thanks,
    challa

  • Mount error when mounting Windows Server share

    Trying to mount a share on a Windows Server I have in my home.
    When I use:   
    smbclient -L SERVERNAME -U administrator
    and I enter the password after the prompt
    It returns a list of all the shares in the server like so:
    Domain=[SERVERNAME] OS=[Windows Server 2003 3790 Service Pack 2] Server=[Windows Server 2003 5.2]
    Sharename Type Comment
    SHARE1 Disk Shared folder
    SHARE2 Disk Shared folder
    SHARE3 Disk Shared folder
    Domain=[SERVERNAME] OS=[Windows Server 2003 3790 Service Pack 2] Server=[Windows Server 2003 5.2]
    Server Comment
    Workgroup Master
    but when I try to mount of the shares with
    # mount -t cifs //SERVERNAME/SHARE1 /mnt/mountpoint -o user=administrator,password=password
    it returns an error
    mount error: could not resolve address for SERVERNAME: Unknown error
    Am I doing something wrong?
    Thanks,

    the SERVERNAME in these commands is a netbiosname and can differ from the  hostname.
    Smbclient seems to use it's own method to resolve netbiosnames, possibly the mount command uses a different method.
    Try the mount command with the ip-address of the server instead of SERVERNAME to verify mounting the share works.
    If the share can be mounted by //ip-address/SHARE1 , you may need additional options for the mount command to make netbios name resolution work correctly.
    check man mount.cifs .
    edit : typo's
    Last edited by Lone_Wolf (2013-08-10 12:40:47)

  • URGENT: Substitution Problem when deployed in Server

    Hello:
    I am facing a strange problem in student system self-service application customization in oxford university.
    I have create a new XxigsPersProgAttemptVO extending PersProgAttemptVO and done the substitution. When run the the page though JDev it was showing the substituted values.
    I have deployed the JPX and VO xml, classes into the server.
    and bounced the apache.
    When i run the application it's throwing following error
    oracle.apps.fnd.framework.OAException: oracle.jbo.NoDefException: JBO-25002: Definition AttendanceTypeDesc of type Attribute not found
    When i view the About this page Business components list, i couldn't find XxigsPersProgAttemptVO VO object.
    But when i run the same page through JDEV, it's shows me my custom VO and substituded VO and extended EO.
    which was right and page was working fine.
    and when i run
    jdr_utils.PRINTDOCUMENT('/oracle/apps/igs/person/components/server/customizations/site/0/PersProgAttemptVO',1000);
    it's showed me
    .........RESULT:
    <?xml version='1.0' encoding='UTF-8'?>
    <customization xmlns="http://xmlns.oracle.com/jrad" xmlns:ui="http://xmlns.oracle.com/uix/ui" xmlns:oa="http://xmlns.oracle.com/oa" xmlns:user="http://xmlns.oracle.com/user" version="9.0.3.8.13_1550" xml:lang="en-US" customizes="/oracle/apps/igs/person/components/server/PersProgAttemptVO">
    <replace with="/oracle/apps/xxigs/person/components/server/XxigsPersProgAttemptVO"/>
    </customization>
    which was also right
    then why i am getting the error in server and why the substitution is not taking in server.
    Can any one help me in this regard pls?
    Many Thanks in advance
    Thanks and Regards,
    Gupta

    just want to add few things
    I am substituting the VO which was used in subtab
    I just found an article in Metalink for the similar issue and found as a bug in OAPageBean.java.
    Metalink Doc ID: 418682.1
    Symptoms
    In Oracle Applications 11i, after extending any framework page by doing VO (View Object) substitution for any VO that is found in subtab in any region in the page either by adding a new attribute to the VO or changing any clause in the VO query such as adding condition for the WHERE clause.
    Then deploying the extension to the server successfully, and after that going to the extended page to check the substitution by pressing on (About this page) , and the result will be that you will be not able to see the new substituted VOs.
    Or in case of adding a new attribute to the VO, you will get a framework exception saying that the "new attribute" is not found.
    Cause
    This is caused by the following INTERNAL bug that is not published through Metalink to customers, and it is reported on R12 and backported to R11i :
    Bug 4970554 - VO SUBSTITUTION NOT WORKING
    Which say that: any substituted View Object used inside a SubTab Layout is not working because of a defect in the code of file (OAPageBean.java) for any version prior to (115.545.115104.3) in Oracle Applications 11i
    Please let me know if you have any ideas
    Thanks and Regards,
    Gupta

Maybe you are looking for