Problem with 8800

I have unlock 8800. v4.2.1.68 (platform 2.3.0.54)
My problem is with dialing a number. few local numbers when I dialed I get the message "customer is not available" . When delete the number from phone book and direct dial it goes through. When I installed my sim card in other phone no problem.
Only time I have this problem when number is save in phone book, otherwise the number is going through without problem.
please help
Solved!
Go to Solution.

There could be any one of a couple solutions... Try these:
1. Make sure you set your own country code at Phone dialer Screen > Options > Smart dialing.
Set your Country Code in this format: "+xx" where xx = your country code. Some countries have two or three digit Country Codes. Do not place the '+' in your contact's entry.
* In the US, set this Country Code as "+1", and place your local area code in the proper box (this normally the default setting in a new BB).
2. At the same location, change the National Number Length to the number of digits for your country (since some countries will have less than 10 as set as the default in the BB). Find out the total digits, minus the country code. Do not place the '+' in your contact's entry.
* For example, some countries have a total number to 8 (plus 3 for country code). You would enter "8".
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

Problem with 8800 Sirocco

Hey i have just bought a 8800 sirocco edition phone. I want to transfer music onto the phone from my PC via bluetooth as i have no wires or anything to connect any other way. I try to connect via bluetooth but it says cannot be connected check that you have the correct software drivers etc. I dont know what programs i need to do it or anything so if anyone can help me i would be grateful. thanks
MIKE

Hi,
Go to Control Panel and open Microsoft's "Bluetooth Devices" BT UI. Does it work OK???
If not then your BT HW is using some other vendor BT driver (and Nokia is not support that one). How is made that BT driver and what version it is?
If you want to try to use MS BT driver:
1. Go to Control Panel, System, Hardware and Device Manager.
2. Open Bluetooth Devices (or Radios), select that device, click Action, Uninstall and OK.
3. Click Action and Scan for hardware changes.
(windows should automatic update install MSBT drivers)
4. After that there should be "Microsoft Bluotooth Enumerator" installed also.

HT3910 I face problems with the Nvidia 8800 GS on my iMac 24'' 3.06Ghz intel core duo. OS 10.06.08. What can I do to solve the problem and if you recommend upgrade to mountain Lion

I face problems with the Nvidia 8800 GS on my iMac 24'' 3.06Ghz intel core duo. OS 10.06.08. What can I do to solve the problem and if you recommend upgrade to mountain Lion

If you want to sync it to the iPad from that Mac, you need to upgrade it to at least 10.5.8.
If you want to copy the music to another Mac, you don't. Move the iTunes folder of the item in the Finder's sidebar over as you would any other folder. If you put it somewhere other than the Music folder, launch iTunes with the Option key held down and point it to that location.
(61713)

Big problem with AE CS3 - abnormal slow with nvidia 8800 GTS 512 !

I try everything, newest drivers (nvidia 8800 GTS 512), older drivers, beta drivers, alternative drivers, uninstall QTime, disable OpenGL in After Effects, delete openGL plugin.... Simply, did not help. AE CS3 is abnormal slow, type text, draw and edit mask, any kind of moving element , moving windows (interface).... everything. When turn on openGL, openGL work fine, fast, smooth., but non openGL operation (written above), still the same! I did some test and found that similar problem have with encore (not my primary application, but...). Other programs work perfectly (premiere, photoshop, illustrator). I have core2 quad 6600 @ 3 GHz, 3 GB RAM, 8800 GTS 512 @ 2560 x 1600, win XP pro strong configuration but unusable for AE CS3!!! I try to reduce resolution, but also, did not help.
Please, is there anyone with some solution? Is problem with AE or drivers? Thanks.

>My 8800GT is not going to work with AE and it's listed under Adobe's
>supported graphic cards????
That's premature to say. Please understand that in the OpenGL game there are just too many varaibles, a lot of them outside the control of Adobe or any other software vendor for that matter. Please consider the following:
- if tested, a card is usually tested in one configuration available at the time that presumably will be the most common one bought by users. There is room for better sub-versions (more VRAM, higher memory clock), as well as weaker ones (less VRAM, lower clock speed).
- the previous applies to the host computer. Nobody can test the 100 new different motherboards that come out every month let alone all that are already on the market. Same for RAM, processors, other peripherals.
- multiple vendors may produce cards based on the same design, but may use different BIOSes and branding
- even under ideal conditions, a given graphics card will be tested in about 30 different computer or so - some in Adobe's lab, others with Beta testers. As it stands, neither of them will necessarily coincide with your configuration nor will anyone throw a lot of money out of the window just to buy a hundred new testing machines...
- BIOS configuration, motherboard voltage fluctuations, PCI timings and whatnot can vary from user to user and thus have drastically different influence how a certain component behaves.
- lastly, driver configuration can vary. Even with seemingly the same driver version, the config may auto-adapt to different settings based on the environment it finds.
So given all of the above, please understand that this is a *******' tough job and by all rights nobody intentionally tries to scam users or something like that. You will also find it hard to blame anyone in legal terms, as you usually agree to use the software "as is" - with all it's flaws. As David says - please try first. We will gladly try to help you sort out any issues and who knows - none of the problems affecting other users may come down on you and you'll be a happy camper after all.
Mylenium

Problems with a Nvidia GeForce 8800 GT

Hey Guys,
Alright so....I bought a refurbished Mac Pro from the Apple Store about 2 weeks ago. The first thing i did was upgrade the RAM up to 10 gb add a second Hard Drive and a new Nvidia graphics card. So far all of them work great, and i havnt seen any problems. The graphics card was the most challenging thing for me to install, because i dont have much experience with installing graphics cards. The card works great to my knowledge and it shows up in my system profiler. But the reason i wanted to buy the card was for running applications on my Vista Partition, that is run by Parallels. And that is where im having the problems. at first i tried to run a game and it showed up but it was very off center....50% of the window wasnt showing up on my screen, like it wasnt lined up correctly, but i figured i just needed to mess around with it a little bit, i didnt mess with it then and then went out of town and came back 3 days later and graphics on Vista (not just when i run the programs but when from the log in screen) are very messed up, everything shows up but the colors arnt blended together, its hard to describe without showing a picture.
But so far everything on OSX runs fine, and i havnt really encountered any problems. I never uninstalled the ATI Radeon 2600 that came with the computer because i didnt see the harm in having two.
The Graphics Card was bought threw the Apple Store, so the only solutions i can think of are that a) i need to download new drivers for the vista partition to accept it, but where would i get them because the Mac Version doesnt have any drivers because a Mac shouldnt need them, right? and then b) that its just some weird problem with Vista and i should just delete the partition and reinstall it. or C) i made some sort of error when installing but that wouldnt explain why its fine when using OSX, unless OSX is still running of the ATI Radeon primarilly....
Any suggestions would be great
thakns
trey

Vista on a Mac Pro graphics is the same as on any PC system, you need to get the drivers, and you may need to uninstall and delete the ones Windows or Apple installed (BootCamp 2.x you installed off your Leopard DVD).
However, you aren't going to get the level of graphics performance that you will running in a VM as you do natively.
Early on with Fusion, it would over-write the "good" graphics drivers though that is now fixed I'm sure, but I never went back to Fusion and just run Ultimate natively.
http://www.guru3d.com/category/driversweeper/
http://www.evga.com/forums/tm.asp?m=396474
http://www.nvidia.com/content/drivers/drivers.asp
Having ATI and Nvidia cards and drivers together might cause problem - maybe someone else knows better about that.
The Mac does need drivers. The OS X drivers are bundled into 10.5.x updates. Windows is still Windows and different OS and needs drivers.

Problem with nvidia driver and GeForce 8800

Hi,
I installed nvidia driver with guide on arch wiki.
But unluckily when i typed "startx", my monitor lost signal and i dont have any other option then restart computer.
This is not for the first time when it happened. I have exactly same problem in every other distribution.
I have GeForce 8800gts and LCD monitor Samsung SyncMaster 204b.
And there isnt problem with hardware because in MS Windows or with VESA driver it works fine.
Here is mine Xorg.conf
http://www.blankpage.ic.cz/xorg.conf
Please, have somebody any ideas how to make it works?

Your not the only one with nividia problems
But on a more serious note, have you tried all configuration steps outlined in the Arch Wiki?
Moderator edit: Picture NSFW. It is also too big.
User edit: Fixed with Thumbnail.
Last edited by jwele (2012-07-04 21:00:37)

Mac Pro 2008 with 8800 GT, hard freezes with screen savers/OpenGL. You too?

I have been experiencing random intermittent hard crashes of my "early 2008" model 8-core Mac Pro. Now I have finally found an easy reproducible test case (see below), and hope others will try it and post the results. This is a video-driver related crash that I have now duplicated with two different video cards.
The symptom is that my screen randomly freezes. The mouse moves, but there's no way to use the Mac[1]. Holding the Power button to force the Mac to shutdown is the only way out.
Usually, this occurs when I get to my office in the morning, or after the gym. That's because the screen saver is running. I found that the screensaver, other OpenGL/3D type applications, are what triggers this bug.
The bug seems to be with the graphics driver. Immediately before the freeze, messages like this are printed in the system log:
Mar 26 18:34:14 Mac-Pro kernel[0]: NVChannel(GL): Graphics channel exception!
status = 0xffff info32 = 0xd = GR: SW Notify Error
Mar 26 18:34:14 Mac-Pro kernel[0]: 0000000c
Mar 26 18:34:14 Mac-Pro kernel[0]: 00200000 0000502d 00000470 00000000
Mar 26 18:34:14 Mac-Pro kernel[0]: 00000482 000002ac 00000003 00000003
Mar 26 18:34:14 Mac-Pro kernel[0]: 00000000 00000000 01be0003
Mar 26 18:34:14 Mac-Pro kernel[0]: NVChannel(GL): Graphics channel exception!
status = 0xffff info32 = 0x3 = Fifo: Unknown Method Error
Mar 26 18:34:14 Mac-Pro kernel[0]: 0000000b
Mar 26 18:34:14 Mac-Pro kernel[0]: NVChannel(GL): Graphics channel exception!
status = 0xffff info32 = 0x3 = Fifo: Unknown Method Error
Other errors like these also appear (the actual log output volume is too large for this forum):
Mar 26 21:15:15 Mac-Pro kernel[0]: NVChannel(GL): Graphics channel exception! status = 0xffff info32 = 0x6 = Fifo: Parse Error
Mar 26 18:34:14 Mac-Pro kernel[0]: NVChannel(GL): Graphics channel exception! status = 0xffff info32 = 0xd = GR: SW Notify Error
Anyway, finally I found on another thread about a similar issue[2], a recommendation to run Folding@Home program to trigger the freeze. They were talking about another Mac model, but sure enough, it triggers my problem every time. I downloaded the client[3], installed it, and then launched the app which gets put in the Applications folder. It doesn't even finish bouncing once in the dock before the Mac Pro freezes.
This is not a bug specific to Folding@Home; juding from the log messages and the effect, this is exactly the same crash that is intermittently triggered by the default Mac OS X screensavers (I use Arabesque, but I think any OpenGL screen saver does it). It's just that running Folding@Home is an easier way to trigger the bug than leaving your screensaver running for hours.
So, that is pretty unfortunate, right? I mean, not only can my new Mac Pro not sleep without losing all unsaved data (yes, I have the reboot-instead-of-wake problem[4], too, but that is another issue...) but it also crashes at random whenever the screen saver runs for a while, or somebody uses OpenGL programs. I have set my machine to never use the screen saver, but still.
So, first and foremost, my question for other 2008 Mac Pro owners with the 8800 video card is: does your Mac puke all over itself when you launch Folding@Home?
I just found it a little bit hard to believe that every Mac owner of the most expensive new Mac and the higher end video card will have these crashes. It could be, but it seemed far-fetched. So I tried some troubleshooting:
a
1.) I considered that I had a bad video card, so I got another GeForce 8800 GT and installed that. Still crashed.
2.) I disconnected my second monitor, and tried it with only one monitor. Still crashed.
3.) I booted from the pristine boot disk my Mac shipped with (10.5.1). Still crashed.
4.) I reduced the resolution on my 30" Cinema display to 800x600. Still crashed.
5.) Just to stave off the usual chorus of "try zapping your PRAM" posts, I zapped the PRAM. Of course, this did nothing (I don't think this has really fixed a problem since the 1990s...). Anyway, it still crashed.
6.) In doing all these tests, I disconnected all USB/FireWire peripherals.
7.) My Mac is totally up-to-date with Software Update as of Thu, Mar 27, 2008. Mac OS X 10.5.2.
I don't want to return this Mac to Apple; it is wicked fast and that really helps me with my work. But, the frequent crashing really is a productivity-killer.
So: does every 2008 Mac Pro owner with an 8800 GT have this problem?
(Note: there are lots of similar problems with other Macs and the new Mac OS X 10.5... I hope to specifically address this particular model and crash in this thread.)
If not, I will go to the next extreme step: pulling out some of my RAM. I have 12GB of RAM, and it all seems to work fine, no parity errors or anything. But I know sometimes problems don't happen unless there's "too much" RAM, "too high" resolution, and so on. But I would like to hear from others before I go banging on my precious DIMMs and riser cards.
Thanks for any information!
The next step will be to determine if this is just another unfortunate defect that affects ALL 2088 Mac Pros (in which case I would want to keep my fast Mac and wait for fixed drivers), or if perhaps just a subset of them have defective video cards that cause the driver to crash in this way (in which case I would want a replacement).
---------- NOTES: ----------
[1]: I can connect via SSH on the command line to the Mac. However, the GUI environment seems borked; opening apps or trying to gracefully quit them via AppleScript either does not work or really hard freezes everything, such that SSH no longer works either.
[2]: A similar (but perhaps different) issue affecting notebooks is discussed here, and there are some people with Mac Pros, too: http://discussions.apple.com/thread.jspa?messageID=6786960
[3]: The Folding @ Home client, which can be used to trigger this bug, can be gotten here: http://folding.stanford.edu/English/Download
[4]: The severe defect affecting many (most?) 2008 Mac Pro machines' ability to sleep without losing data is discussed in this other thread: http://discussions.apple.com/thread.jspa?threadID=1353551

Hello guys, thank you for the replies.
I do have more data at this point.
ujeezy: Those posts on MacNN and others like them did give some clues.
Jon BWFC: I think you are (partly) right that it's (partly) an issue with the driver. But I have confirmed with a fair degree of certainty in my case that it is a hardware issue too, likely with the video card and not the Mac Pro itself.
cmcom: I think it sounds like you problem is different than the one we're talking about (although who knows, the driver could be causing that too). The freeze we are seeing locks up the whole Mac, and no application crash report is produced.
I had another GeForce 8800 card, so I went through some exhaustive troubleshooting. I tested each card, installed in each of the 16x slots, booting from either my normal 10.5.2 boot disk or a clone of the pristine virgin system disk that shipped with the Mac, and tried to see if the Mac would crash.
Unfortunately this was harder than it seems, because:
a.) both my GeForce 8800 cards appear to be defective, but in different ways (see [1] and [2] below)
b.) In my testing, I thought I was seeing the crash sometimes, but later I discovered that there are different ways to make the Mac crash like this. That is, there are bugs in Mac OS X 10.5.x (probably in the NVIDIA driver) that cause similar crashes, and these bugs occur on all Mac Pro units and even other Mac models, without any hardware defects. Unfortunately, the Folding@home exercises one such bug.[3]
So the upshot is, all those times I was using Folding@home to test this issue were bogus, because Folding@home crashes any Mac Pro with the NVIDIA card, and crashes MacBook Pro machines with NVIDIA chips as well.
Argh! So I had to retest. It took a couple of days but I found another reliable way to crash my Mac Pro, more quickly than just leaving the screensaver on for a day or two: run this OpenGL virtual fish tank simulator[4] for 2-3 minutes. Unlike the Folding@home test, this did not crash any of my other Macs, and after exhaustive testing I found that it ONLY crashed the Mac Pro with one of the GeForce 880 cards installed, and not the other one. This was regardless of what slot it was installed in or what boot disk was used.
Whew! So, I concluded that indeed, there is a hardware defect in one of my GeForce 8800 cards which causes the machine to lock up. [2]
What made this problem much harder to deal with was the fact that Mac OS X (specifically the graphics driver parts of the OS, perhaps NVIDIA-specific) crashes with these same symptoms in other cases too. Like when you run Folding@home, or in some of these cases people are talking about with their MacBook Pro machines.
So, when there is a bona-fide hardware defect, it is really hard to isolate. (It took me like four days.)
The thing is, the defective NVIDIA card that crashes the Mac[2] was a REPLACEMENT card for the 8800 card that shipped with my Mac. I called Apple about the video artifacts I was seeing and they replaced the card.
I am now running the original card (and suffering the ugly video artifacts, but no crashes). At my own expense, I ordered an ATI card (the RADEON HD 2600 XT) and I will install that.
I hope someday to have my Mac work without graphics glitches or crashes. For now, operating (mostly) without crashes will have to do.
The original problem with this Mac continues, though: the video doesn't work correctly; it starts displaying visual artifacts after 1-72 hours of use[1]. That could either be because:
a.) a hardware defect in that video card
b.) a software problem with the driver/OS
c.) a hardware defect in the Mac itself
I strongly suspect A, but hopefully my buying a different card and testing with that will help further isolate what is wrong.
I am marking this thread "solved" because the specific issue I originally posted about has been resolved: the GeForce 8800 card causing the crashes is defective, and using another card fixes that issue.
[1]: The original GeForce 8800 card that shipped with my Mac Pro exhibited annoying-but-not-deadly video artifacts, which can be seen here: http://masonmark.com/wp-content/uploads/2008/04/bogusvideoartifacts.jpg
[2]: Apple replaced the video card, and that is when my deadly video-corruption-plus-frozen-Mac crash problem began. A screenshot example of that problem can be seen here: http://masonmark.com/wp-content/uploads/2008/04/crashedmac_pro_akashitball.jpg
[3]: The red herring in this case was the Mac OS X bug (seemingly specific to NVIDIA-equipped Macs including Mac Pro and MacBook Pro) that causes a very similar full system crash. This bug can easily be triggered by running the Folding@home version "6.10beta2" demo application. That is a serious bug, and since my employer is a Mac software company I reported this bug to Apple via the official channel. It is Apple bug number 5830772.
[4]: The OpenGL fish tank simulator I found, which would trigger the system crash caused by my defective 8800 video card (but would not crash any other Mac, or crash my Mac Pro with the other 8800 video card installed) can be found at: http://uri.cat/software/Fish/

Two display problems with my new MacPro! :/

I recently bought a new MacPro to replace my PowerPC, and am having some odd video problems I did not have with the old computer (yes, using same display). Here's some quick stats I think are important.
1. 30 inch Apple HD display (used on both computers.)
2. Old video card = Radeon X1900 - NEW video card = Geforce 8800 GT (came factory installed)
3. Old OS = 10.4.11 Tiger New OS = Leopard (with all current updates. Also factory installed)
4. Quicktime Pro on both systems fully updated
5. Both Machines had all updates installed at the time of this problem (which is since i got the new machine)
Here's the two problems...(btw NEITHER of these happen when the display is hooked up to the old computer. only the new MacPro with a different video card and OS)
1.) When I play back video (sometimes in FCP (all types of files), sometimes in QT (.mov), and sometimes even on youtube and vimeo (so those are .flv files!) only SOMETIMES do I get these odd vertical refresh-looking lines. It makes the video somewhat flicker and you can see them crawl upwards kind of. The odd thing tho, is if I play that art of the video over and over, at times it will happen, and at other times it will not. same file, same part. I also noticed it does NOT stay on the file when exported from FCP and burned to DVD, so I'm thinking it is purely playback.
2.) Some files when played back in quicktime will get extremely choppy. (Locally played files). I will then click the desktop to make finder the front most selected program...and the files will then play smooth. if I select the QT window again, it will get choppy and flicker again.
I feel like I have a refresh rate problem, or maybe even a driver problem. The thing is, of course the drivers are not updated outside of auto updates, and I have installed everything available there.
When I open up my display settings, the refresh rate box is grayed out...so changing the rate isn't possible. Also, with my old computer/video card, I had an ATI control panel...the geforce does not have one...only the build in OSX display control panel.
Has anyone heard of this? I have posted in a few different places, and have received absolutely no replies. It's really frustrating, and sitting on the phone for hours with apple support to have them say "never heard of that problem" or have me lug the **** thing into a apple store and be without my computer and unable to work doesn't sound fun either.
it's not stopping me from doing anything..it's just annoying and frustrating cause I can't make it stop. I'm thinking it might be a problem with the leopard drivers that hasn't been addressed yet? I dunno.
Any suggestions?
thanks in advance,
Damion

UPDATE ::
In reading an old solution on how to get rid of the dancing pixels I get every once in a long while on this display, I downloaded SwitchResX and am using the demo to test and see if switching the refresh rate to 58khz will help in the line problem...and lo and behold...it kinda does. it is now only noticeable on fast moving action when put into full screen mode.
The QT flicker problem has NOT gone away...but I'm expecting that the horizontal lines running vertical are a refresh rate problem as I had thought.
My question, anyone know if apple is aware/working on this?
Also, why is the refresh rate not changeable with the 20 inch HD display settings in the display control panel??
I'd much rather use OSX to control my display than a 3rd party application! :/

Problems with installing the X-Fi Xtreme Gamer Soundc

Hello,?I've a new X-Fi Xtreme Gamer Soundcard, but I'm not able to install it. I tried the CD, the driver on the page and the ISO somewhere in the forum. I get everywhere the same errormessage:?"No audio device that is compatible with this application can be found" I have deinstalled and deactivated the onboard sound in the bios. I have no idea what I can do to solve the problem. greetzM. Schwander?My system:- XP Prof- CPU: Intel Core Duo 2.66- Mainboard: asus p5b-e- graphic card: Nvidia GeForce 8800 GTS??

the soundcard is correctly in the slot ... (got the some problems with another slot)
now my device is found and i can start the installation, but after a several time, there's a bluescreen with something about "h20x2k.sys" written.Message Edited by wuff on 2-04-20070:22 AM

Problem with the buttons

Recently I have problems with some buttons on my 8800.
When I hit the trackball the BB writes "Uo". When I hit the 'back' button it writes "Hl". Also the menu button does not what he has to do. Anyone the same problem or even better a solutions for this problem?
Bye, Ben

You are not alone. the same thing happened to me today with my 8820.
it worked fine for one call then i hung up and tried looking up a number. Track ball dosn't work at all, their isnt even a backlight on the trackball. the back button types in hl. i also think my e button is enter but i dunno. that one seems on and off.
Edit. I found this:
http://www.blackberryforums.com/general-8800-series-discussion/114752-blackberry-button-problem.html
Message Edited by jasgud on 07-27-2008 08:25 PM

Problems with TV - Card after Kernel Upgrade

Hi Folks,
since the last Kernel Upgrade I've got problems with my tv tuner card. Since ever I had to set the tuner manually to 38. But now it seems that its not enough just to set this type.
I used this script to set up my card correctly:
modprobe -r cx88-dvb cx88-blackbird cx8802 cx88-alsa cx8800 cx88xx
modprobe cx88xx tuner=38
modprobe cx8800
Now I've got weired sound and only a few stations, with a very poor picture quality. After reloading the modules with the script dmesg says:
tda9887 2-0043: destroying instance
tuner-simple 2-0061: destroying instance
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 16
cx88[0]: subsystem: 0070:3401, board: Hauppauge WinTV 34xxx models [card=1,autodetected]
cx88[0]: TV tuner type 38, Radio tuner type -1
tuner' 2-0043: chip found @ 0x86 (cx88[0])
tda9887 2-0043: creating new instance
tda9887 2-0043: tda988[5/6/7] found
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
tveeprom 2-0050: Encountered bad packet header [00]. Corrupt or not a Hauppauge eeprom.
cx88[0]: warning: unknown hauppauge model #0
cx88[0]: hauppauge eeprom: model=0
tuner-simple 2-0061: creating new instance
tuner-simple 2-0061: type set to 0 (Temic PAL (4002 FH5))
input: cx88 IR (Hauppauge WinTV 34xxx as /class/input/input8
cx88[0]/0: found at 0000:01:07.0, rev: 5, irq: 16, latency: 32, mmio: 0xe6000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
From my (limited) point of view the problem is, that tuner-simple does not loads the correct tuner type? I've looked into modinfo from tuner-simple but there is no parameter for type... What else could be the problem?
Thanks in advance
Badcel

Hi cjpembo,
my Card looks like:
01:07.0 Multimedia video controller [0400]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
01:07.1 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8811] (rev 05)
My card seems to be another version. Regarding to the v4l Wiki: http://linuxtv.org/v4lwiki/index.php/Tu … ted_Tuners
A new Hauppauge WinTV PCI-FM card is here (pci_ids: 14f1:8800, 14f1:8811), using the TCL MFPE05-02 PAL (DK BG I) FM tuner. It just implements mk3 API, you can use philips 1216me mk3 (tuner=38) instead.
If I don't specify any module parameters, the tuner type 0 is selected.
ACPI: PCI interrupt for device 0000:01:07.0 disabled
tda9887 2-0043: destroying instance
tuner-simple 2-0061: destroying instance
Linux video capture interface: v2.00
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 16
cx88[0]: subsystem: 0070:3401, board: Hauppauge WinTV 34xxx models [card=1,autodetected]
cx88[0]: TV tuner type -1, Radio tuner type -1
tuner' 2-0043: chip found @ 0x86 (cx88[0])
tda9887 2-0043: creating new instance
tda9887 2-0043: tda988[5/6/7] found
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
tveeprom 2-0050: Encountered bad packet header [00]. Corrupt or not a Hauppauge eeprom.
cx88[0]: warning: unknown hauppauge model #0
cx88[0]: hauppauge eeprom: model=0
tuner-simple 2-0061: creating new instance
tuner-simple 2-0061: type set to 0 (Temic PAL (4002 FH5))
input: cx88 IR (Hauppauge WinTV 34xxx as /class/input/input8
cx88[0]/0: found at 0000:01:07.0, rev: 5, irq: 16, latency: 32, mmio: 0xe6000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
The card is not listed in my local PCI ID repository. And it seems, that the PCI ID is not known to the PCI ID Repository: http://pci-ids.ucw.cz/iii/?i=0070
Badcel
Last edited by badcel (2008-08-24 09:46:18)

Gigantic problems with graphc card GeFore 8800GT under MacPro

Hello
I'm a user of MacPro 2 Quad-Core 3GHz computer with NVIDIA GeForce 8800 GT graphic card.
This is my second card like this one becouse I can't find any other with low price for exchange and for good using OpenGL.
Now I have gigantic problems with this card under Mac again, please help.
It have extreme temperatures and graphic crashes when I use on any game or anything which harder use it. At real, my older card before burn out and go to trash after this. Now it comes again
Is there any software to speedup windmill or any thing in my system what I can change for this? I have a plan to buy a cooler, but I need help in software before this.
Why good quality company like Apple use this bugged cards in expensive computers, I can't understand this.
Regards
Dawid

Nvidia had / has had / a run of problems - and Apple can choose Intel integrated, AMD.... or Nvidia basically. Though on PC side there are reference designs and then HIS (makes a really good ATI with its own design and cooper cooler), EVGA on Nvidia front.
We don't get all that many options.
Drivers always get a lot of "heat" and criticism.
Was so glad to have X1900 as a choice, but not the $399 (or wait and $250 BTO) 5 yrs ago, and its history of problems. And recalls. Or ATI 2600XT. Can't win for losing sometimes.
One reason I went and bought GTX 460 and run Windows on my Mac Pro today of all things. Other reasons too over the years. Locked into EFI graphic cards and you can have anything you want on the salad bar, as long as you want either shrimp or chicken.
So heat up the oven, get out the egg timer, and have at it!

945GCM7 problems with USB

Hi all,
I seem to be having problems with my USB and for what i can tell it is my mobo thats the problem.
The problem is that i can plug in my USB pendrives and they are recongnised perfectly fine, and are readable fine but when i try to write files to them they are quickly disconnected and then reconnected, inturupting the transfer.
I know its not my windows because i have just done a fresh install and still have the same problem. Its also not the pendrive beacuse its the same on all pendrives i use and the pen drives work fine on others pcs. It was working fine up untill about 4 days ago.
It be really cool if i could get some help, any ideas?
# Pentium(R) Dual-Core CPU E5200 @ 2.50GHz (2 CPUs)
# MSI 945GCM7 MS-7507
# 2x2GB crucial DDR2
# BFG NVIDIA GeForce 8800 GT 512MB PCI-E
# MAXTOR, 250GB, SATA
# Western Digital, 250GB, SATA
# Stock Sound card
# Windows XP Home Edition / Service Pack 2
# sumevision P4 550W 35A

Quote from: nightmare99 on 04-March-09, 16:48:43
Are you using front USB ports? If so disconnect them and use the back ones for testing purposes.
i have done, still know success, im starting to think that theres a problem with the controller so i am gonna buy a pci card with usbs and try that.

Premiere Elements 13 , Problems with new text/titles

Premiere Elements 13, bisher keine Probleme. Nachdem die Filmlänge etwa 15 Minuten beträgt immer größere Probleme Titel/texte einzugeben. Wartezeiten sind extrem lange oder Programm stürzt ganz ab.

High ATR,
Computer running on Widows 7 ,64 Bit System, Service Pack 1, Processor AMD Phenom(tm) X4 945 3.00 Ghz;RAM 8 GB
Grafikkarte: NVIDIA GeForce 8800 GT
If the video on the timeline is longer than 10 minutes the problem will be remarkable. The response times adding a title is getting longer(2-15 seconds).
As the video is now 18 minutes the response time is after each action(resizing of letters or any changes of the text) up to 30 seconds or the program crashes completely.
Project settings are the following:
General HD 1080i; 29,97frames/second; Video:1920v 1080 H, 30 fps
Video: maximale Bittiefe, Dateiformat i-frame only mpeg, Kompressor MPRG i-Frame, Standbilder optimieren
The video is a mixture of full HD videos 1920x 1080 .mov and pictures up to 4608x3456 pixels.
When the program crashes I remarked that the main memory RAM(8Gb) was fully used by the premiere program. Might there be a problem?
Thank you for your service.
thomasd
Von: A.T. Romano
Gesendet: Sonntag, 1. Februar 2015 23:55
An: Thomas Deschler
Betreff: Premiere Elements 13 , Problems with new text/titles
Premiere Elements 13 , Problems with new text/titles
created by A.T. Romano <https://forums.adobe.com/people/A.T.+Romano> in Premiere Elements - View the full discussion <https://forums.adobe.com/message/7151822#7151822>

TO BLACKBERRY- YOU HAVE A PROBLEM WITH BLACKBERRY WORLD NOT ACCEPTING CREDIT CARDS

HI, I AM AN OWNER OF A BLACKBERRY Q10 AND A LOYAL BLACKBERRY USER SINCE THE 8800 SERIES BLACKBERRY CURVES. THERE IS SOME TYPE OF PROBLEM WITH BLACKBERRY WORLD. I AM CURRENTLY RUNNING 10.3.2.556. UNTIL LAST THURSDAY BLACKBERRY APP WORLD WORKED WITH MY CREDIT CARD. THEN ALL OF A SUDDEN IT JUST STOPPED. SAYING THAT THERE WAS A PROBLEM WITH THE TRANSACTION AND TO TRY AGAIN LATER. NOW I CANNOT USE MY CREDIT CARD AT ALL. I AM POSTING THIS IN MULTIPLE FORUM BECAUSE I AM NOT THE ONLY ONE HAVING THIS ISSUE. I HAVE RECENTLY POSTED THIS PROBLEM ON CRACKBERRY.COM AND OTHERS ARE HAVING THE SAME PROBLEM. http://forums.crackberry.com/ask-question-f432/why-blackberry-world-will-not-let-me-purchase-apps-when-working-before-1032609/?mn_qa=1#post11839564 AND IF YOU LOOK ON THIS SITE AND CRACKBERRY FURTHER YOU WILL SEE OTHERS ARE HAVING SIMILAR ISSUES. I HAVE ALREADY TRIED TO GO ONTO THE BLACKBERRY APP SITE ON MY COMPUTER BUT NOW THERE IS NO OPTION TO CHANGE THE PAYMENT OPTIONS THERE ANY MORE. WHAT IS THIS. WHY IS IT HAPPENING?????? CAN YOU PLEASE LOOK INTO THIS PLEASE WHOMEVER FROM BLACKBERRY SEES THIS POST. SINCE THERE IS NO NUMBER TO CALL FOR HELP ABOUT THIS I AM POSTING HERE UNTIL SOME TYPE OF BLACKBERRY PERSON ANWERS. I AM ALSO GOING TO TRY AND POST THIS IN THE FORUMS FOR Q10, CLASSIC, PASSPORT, LEAP, ETC., SO SOMEBODY CAN HELP US. SOME PEOPLE SAY IT HAS BEEN GOING ON FOR MONTHS ON THEIR ACCOUNT AND NOTHING HAS BEEN DONE. HELP US PLEASE. THANK YOU.

I have the same problem today. Suddenly Appworld stopped accepting my AMEX credit card. I called AMEX and they told me that all is notmal from their sied and that they did authorize transactions. However, Approwld says that credit card cannot be accepted. WHAT A MESS!!! And there is NO EMAIL or phone number to contact regarding this problem which is quite RIDICULOUS !!!

Problem with 8800

Similar Messages

Maybe you are looking for