Problem with a MSI-6163 PRO

Anyone got an idea what kinda problem i have? I have an MSI 6163 PRO motherboard (with latest BIOS update 3.5), a PIII 700 Cuppermine, 3x256 SDRam, i run Win XP Pro, have a 40 gb harddrive and have been running like this for at least 9 months, without any problem. Suddenly it starts to reboot all the time and now i cant even start it not even in fail safe mode, it reboots before i get in.
Its not a Virus, i have virus checked the hardrive, i tryed with a smaller harddrive (6 gb and win 95) and that worked, i bought a new harddrivce (120 gb) Started to format and install Win XP pro and it starts to reboot again, i have tryed chagne memmorys, graphic adapter, net adapter, soundcard everything, i am going nuts! anyone had probs like this??
I would be more than greatfull if anyone has an answer to this.

Thanks a lot Wonkanoby for the help. It didnt help my error but it sure cleared it up. There were several capacitor that leaked, just as the pics on the site you sent http://www.overclockers.com/tips00140/, it shows clearly on thoose. Cant beleive how that problem can be so big and seems like they are doing nothing about it either.
Well thanks for a great Forum here, and thanks to you Wonkanoby.
The motherboard is dumped... thinking of going back to good old ASUS
Then its Rock´n Roll agian
Have a great day.

Similar Messages

My Msi 6163 Pro doesn't boot !

I change the motherboard Msi 6163 Pro of my old PC but it doesn't boot !!
The diagnostic leds are 1010 (Green Red Green Red) : Testing Base and extended memory ... (from 240k to 640k and above 1Mb)
I test 4 different memory modules on this motherboard : they can't all be out of order ....
- I test PC 100-128 SDRAM 16*8
- and PC 100-128M 8*16
Do you have an idea for this problem ? The mainboard, the memory module, the pentium (pentium III 500)
No overclocking, default configuration, bios has been initialised ...
Thanks a lot.

Hi dude !
I have Msi6163 bx master.... This motherboard support copermine.
Yes..it is a big chance that the problem is related to sdram type memory. I personaly have 512MB of sdram (all 4 slots full) I have mixed sdrams... some are 133mhz, some of them are 100mhz. The bus is overclocked to 133mhz from 100mhz so my p3 650 mhz works on 866 since 2001 year without any problem. I have difficulties to find working sdram on this motherboard when i upgraded it with more memory. Some sdram modules didnt work, some of them has been recognized as half of it, boot problems and so go on... I know that in mynual is written whic sdram must be.
I check now on site http://www.crucial.com/ for the answer for your problem. I found this:
These 168-pin DIMM modules are compatible with your system.:
128MB sdrams: (crucial)
SDRAM, PC100 • CL=2 • Unbuffered • Non-parity • 100MHz • 3.3V • 16Meg x 64
SDRAM, PC133 • CL=2 • Unbuffered • Non-parity • 133MHz • 3.3V • 16Meg x 64
SDRAM, PC133 • CL=3 • Unbuffered • Non-parity • 133MHz • 3.3V • 16Meg x 64
SDRAM, PC100 • CL=2 • Unbuffered • ECC • 100MHz • 3.3V • 16Meg x 72
From: http://www.memoryx.net/ -->
MSI MS-6163 Pro (MS-6163 v2.0) Memory :
Maximum Memory 768MB
Memory Slots 3 (3 banks of 1)
64MB Hyundai/MSI 168p PC100 ECC SDRAM DIMM (p/n MSI-XAJ64)
64MB Hyundai/MSI 168p PC100 ECC SDRAM DIMM (p/n MSI-XAJ64)
128MB Micron/MSI 168p PC100 ECC SDRAM DIMM (p/n MSI-XAJ128)
128MB Micron/MSI 168p PC100 ECC SDRAM DIMM (p/n MSI-XAJ128)
256MB Micron/MSI 168p PC100 18c 16x8 ECC SDRAM DIMM (p/n MSI-XAK256)
256MB Micron/MSI 168p PC100 18c 16x8 ECC SDRAM DIMM (p/n MSI-XAK256)
256MB 168-pin PC100 CL2 2-Bank 16-chip 16x8 SDRAM DIMM (p/n ABS)
Good luck. Let us know if you found the solution. On sunday i will try again to change some sdram to gain more memory Bx master 6163 supports up to 1GB sdram

Msi 6163 Pro

Does anyone could help me, were i could buy the msi 6163 Pro motherboard for replacement of my old one which was totally crash because some of its resistor were damage. I'm not sure if the cause was overheat, or the board might be defective. But I still like this board more than the other. 8)

Only with great luck as a used board from a computer shop.
They were not in production for about 3 years now.

I am having a problem with my 2009 Macbook Pro

Hello Everyone,
I am having a problem with my 2009 Macbook Pro . A few weeks ago I plugged it into the charger after running it down to reserve battery power. It appeared to be charging, but then all of a sudden my clock and calender reset to year 2000 and then my computer blacked out and went dead. I tried to boot it up but nothing happened (literally nothing). I have tried 3 different chargers on it, but all I get is a faint green light and even after hours it still won't boot up. I have tried replacing the battery, but still nothing happens.
Any Ideas? I am pretty desperate to get my computer back up and running before school finals.

You may have to see if an authorized Apple service specialist can check over
the charging system (magsafe dc-in board, power adapter, and MacBook/Pro)
and test or run a diagnostic on it, to be sure there is no damage or failed parts.
When you attached the adapter to charge the computer, after it said it was going
to reserve power, did you shut down open applications and stop using the MB/Pro?
That would've been the thing to do, since the margin of run-time near the bottom
of the power cycle can be wrong by the gauge estimate, it can just quit.
While I have not researched your year/model/series in detail, I do know some
models of Apple portable computers have a small battery or capacitor on the
logic board, separate from the main power battery; it may need replacement.
A service provider w/ Apple training & parts would be a likely resource to fix it.
Good luck & happy computing!

New problem with display on Macbook Pro retina (Samsung panel)

Hello All,
I am a very new people on your forum but a few weeks ago i bought a new macbook pro retina with samsung panel.
I haven't ghosting effect on my macbook but i have a new and really bad problem.
I try to found a some information on Russians forums but nobody can help me with it.
I can see an artifacts in the form of flashing pixels on all display.
It occurs in 20-30 minutes after the start of work.
Today i try to test it on game Dirt 2 and i can see defects after 2 minutes after start. So i think it can be reason with Geforce 650 but when i back to desktop and use HD 4000 i still see a problem.
This is best seen on a black screen with high backlight.
When i try to connect TV via HDMI i can't see any problem in my TV.
So i really don't know what could be the reason.
I attached the video with issue to video hosting
http://vimple.ru/579f880e8b7045e09f8fc5bc097c5e2b
Also i have a many software problem like Crashing safari and iTunes. It can be a few times per day.
I really disappointed with my new Macbook.
I haven't any problem with old 2009 Macbook pro with Snow Leopard but Mountain Lion is not working well.

Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
Regards
TD

Hello, I have a problem with my mac book pro after running the battery dead on a game. The display has shrunk leaving two black margins on either side. What to do ?

Hello, I have a problem with my mac book pro after running the battery dead on a game. The display has shrunk leaving two black margins on either side. What to do ?

Go to System Preferences>Displays and set the resolution to "Best for this computer" (or something to that effect).
Clinton

Having big problems with my new Mac Pro, when I launch Photoshop CC, I get an error message, can carry on but after a few tasks it starts going gar... menus go blank, when you try to save it shows a blank box.... can anybody help?

Having big problems with my new Mac Pro, when I launch Photoshop CC, I get an error message, can carry on but after a few tasks it starts going gar... menus go blank, when you try to save it shows a blank box.... can anybody help?

when I launch Photoshop CC, I get an error message
and what exactly is the text of that error message?

Problems with the (WINDOWS 8 pro -64 BIT) IN THINKPAD L520 - 5016 RL2

I have some problems with the (WINDOWS 8 pro -64 BIT) is not working properly IN THINKPAD L520 - 5016 RL2.
1. Message appears telling me that the drivers of the display has been restored crash.
2. The mouse pointer moves very slowly sometimes, and sometimes does not move for a while.
3. Device software such as lenovo-airbag protection , lenovo-internet connection and lenovo web connection........ its is not compatible with the system, and do not work.
What is the solution؟

Hi, MUJAHED
I have a few questions for clarification I would like to ask about your first two issues:
1) Can you copy the contents of this message and respond back with them. Any error codes or direct quotation from the system can really help in diagnosing a problem.
2) Does this only apply to the TrackPad, or does this behavior also occur with an external mouse? It may help to download the latest mouse drivers for your system, which can be found here.
As for your last issue with the Lenovo service not being compatible with the system: Unfortunately, software for these applications has not been released for Windows 8. Windows has its own network settings that you can use to connect to the Internet and networks, so that is still possible, though you may not enjoy it as much as Lenovo's program.
Best,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

Problems with X-Fi Elite Pro

Problems with X-Fi Elite Pro? Hello, everyone!
I'm from Brazil and?I'm having a huge problem with my X-Fi Elite Pro.
A few months ago, my video card stopped working and I replaced it!
But then, my audio card stopped working properly as well!
I reinstalled all the drivers (Video AND Audio) and my SB played my music for about 2 minutes before stop working! I reinstall the drivers, works for 2 minutes, and stop! Then I change de mode "Game" to" Audio Creation" and it keep working. But the stop 2 minuts after. Then i change de mode "Audio Creation" to "Entretainment". It works for 2 minutes and stop. If i try the 3. time, works for 2 seconds and stop. It also happens in the 4. attempt... the 5?... the 6?...
In this 2 minutes, it works fine! 00%! But then stops, with?no apparent reason!
Can someone help me? I don't know what to do, anymore!
My PC:
Intel DP35DP Mother Board
GeForce 9800 GT GB
SB X-Fi Elite Pro
4GB Ram
Intel Quad Core 2.3GHz
Windows Vista Ultimate 64bits
(Sorry for the bad english! But... you know, i'm not very good with foreing languages! lol)
Thank you all!
Rodrigo Guidini.

Wow, guess nobody can help me out here......

Respected sir, i have problem with my mac book pro 13, i shows question mark when i start up the laptop. so please reply with the convinient solution

respected sir, i have problem with my mac book pro 13, i shows question mark when i start up the laptop. so please reply with the convinient solution

ajit5544 wrote:
.. my mac book pro 13, i shows question mark when i start up the laptop. ...
See here > http://support.apple.com/kb/TS2570

AGP of MSI 6163 Pro (MSI 6163 Ver2)

Hi..wondering if anyone can tell me if msi 6163 Pro (msi 6163 Ver2) can support GF2 Ti Video Card?
Been thinking of getting the Inno3D GF2 Ti Card, but is not able to find info as to whether it will work on it.

and the MSI-6163 v1.0 can support a gf2mx agp card (it's an asus v7100 deluxe)?. I tried to install it but windows98 can't recognise Cd-rom because it says it is a conflict in the bus controller (the exact address is f000-f000f) and it was no way to make it run well. I had to reinstall the old intel740 8mb agp card, and making so the pc become to run properly just like before installing the gf2mx card. Can anyone help me? I'm getting mad about this... :(
P.S. Sorry for the english that maybe it's not quite perfect

Problems with a MSI K8N

So yeah I just bought alot of computer parts including this motherboard. I have my computer area downstairs in my house but I have a spare monitor in my room. After I finished installing everything I pluged the case into the wall and hooked it up. I proceeded to turn the power on and noticed the "NEO PLATNIUM" on the screen I figured everything was working so I turned the power off not thinking it would mess the bios up and took it downstairs and pluged it in again with my real monitor and computer set up. I tried to power it on again and it shut off in like 5-10 seconds I proceeded doing this about 4 times everytime it shut off so I took it back up stairs to see if something became unplugged. From then on I couldnt even get it to turn back on. My case showed a green light but when I pushed power It didnt work. I tried clearing the cmos with no success. I'm hoping somehow you guys will know what to do.
Thanks for you time.

Hey man, I feel your pain, and I feel obligated to post this because of the way everybody else is treating the problem.
Let me point this out to everybody:
This guy knows what he's doing, he isn't doing anything stupid. This IS a problem with this MSI board. How do I know? Because my computer setup is doing the exact same thing. I've been through 2 boards and 3 CPU's now. My setup worked fine for 2 weeks, then one day it just stopped working. It turns on for 5 seconds, then just turns itself off. It does not post. D-Bracket claims it is a bad or badly seated CPU. It lies. I just put in a brand new working CPU today, and i'm getting the same issue. It IS the motherboard. Now I just have to get it fixed from MSI somehow. I feel comforted knowing i'm not the only one with this problem. I just replied to some other guys post about having this issue.
I just posted my issue on another motherboard, but I will post it here as well for you all to read so that you know this issue is more widespread than it may seem.
Boy, what a ride this has been so far.
Let me briefly explain the issue. Got a the motherboard and a XP64 3200+ from newegg.com, etc. Plug it all together - nothing. I've built plenty of systems, and i've built several using thet MSI K8N board, also. I discover that the RAM is bad and the motherboard is also bad. Repeat as necessary several times.
Long story short, I'm on CPU #3 and Mobo #2, soon to be #3.
The 1st CPU was returned because a friend was working on the system and pulled the heatsink off and the CPU stuck to the bottom of the heatsink and some of the pins got bent/broke. (This is due to the poor design of the heatsink holder on the MSI board. There is WAY too much surface area between the heatsink and the CPU for the heatsink to be enclosed how it is on this board.. trying to pull them apart like that is just impossible. It can't be done. It has to be at an angle. . Only way).
Now, after we got the motherboard RMA'd and bought a new CPU, everything worked fine and dandy.
Two weeks later, one day the system just won't boot. There is no video signal at all. The problem is that when the system turns on, it runs for about 7 seconds.. all the fans turn on, etc. and then it just turns itself off.
I've tried different power supplies, i've tried only with the CPU, Mobo, and RAM, and hell, i've even tried it without the RAM. I've tried it out of the case, to check for shorts. Nothing. I've checked the power switch to be sure it isn't being stuck on, it's not. There is no reason, whatsoever for the computer to do this. The Diagnosis LED Lights show all 4 red which means badly seated or damaged CPU. Ok. So I RMA the CPU. I just get it back today, and we're on the 3rd CPU now. Plugged it all together.. brand new CPU. The old one obviously didn't work or else they wouldn't have RMA'd this one to us. They should have tested this one first too, I think.
SAME PROBLEM.
The computer turns on, lights fans etc. come on, and 7 seconds later the computer shuts down. There are no BIOS beep codes, no video signals, NOTHING.
This really only leaves me with one conclusion - the motherboard is bad. There are only 2 choices, CPU or Motherboard, and the CPU is brand new.. and the problem was the same with the last one ... common denomonator is the motherboard. Now its been so long waiting for the RMA on the CPU and everything ... plus the 2 weeks that this motherboard worked, that newegg probably won't take back the motherboard. My only real options is to send it to MSI for repair or something.
This is a very sad day. The only thing I can think would have happened is that the motherboard had some kind of voltage issue to the CPU.. maybe some kind of electric jolt that damaged the CPU socket and the CPU itself so that now nothing works. I'm most afraid that the motherboard is damaging the CPU's.. and that this new one we just put in could be damaged from the motherboard also.
These things are expensive... I can't afford for all this to keep going. I've easily spent $150 - $200 doing RMA's for all this ****. It's just ****ing rediculous. I should win an award for most computer problems.
Before I start freaking out about this even more, let me get to the point of this post.
Has anybody else experienced something like this? Specifically with this board? With something else? What the hell can I do about this, or is my only option the motherboard.. as far as I can tell.. it can't be anything else.
-Kevin

Font problem with Montserrat and Maven Pro from google

Seems like some fonts don't render as they should in Firefox 29.0.1. I tried to use google web fonts like Montserrat and Maven Pro, no problem with downloading but this fonts don't look good.
I tried to install Montserrat to my Windows 7 (64) and deactivated css so that FF runs the font but same problem occurs.
A really strange problem is that from my computer at work this fonts don't work from FF or Chrome, all versions of IE is fine.
At home i have a laptop with same OS and version of FF and from home it works! But not Chrome..
I have search on the net and at your support site but haven't find any answers yet.
You can look at http://arenago.axiell.com for your self. Below is troubleshooting information from my version of FF where this problems occurs (Sorry about the Swedish)
Programfakta
Namn: Firefox
Version: 29.0.1
Användaragent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:29.0) Gecko/20100101 Firefox/29.0
Kraschrapporter för de senaste 3 dagarna
Alla kraschrapporter
Tillägg
Namn: Classic Theme Restorer
Version: 1.1.8
Aktiverad: true
ID: ClassicThemeRestorer@ArisT2Noia4dev
Namn: Firebug
Version: 1.12.8
Aktiverad: true
ID: [email protected]
Namn: HostAdmin
Version: 1.4.9.2
Aktiverad: true
ID: {bd54afa8-b14a-4d7a-aecf-37e34e882796}
Namn: Web Developer
Version: 1.2.5
Aktiverad: true
ID: {c45c406e-ab73-11d8-be73-000a95be3b12}
Viktiga ändrade inställningar
accessibility.typeaheadfind.flashBar: 0
browser.cache.disk.capacity: 358400
browser.cache.disk.smart_size_cached_value: 358400
browser.cache.disk.smart_size.first_run: false
browser.cache.disk.smart_size.use_old_max: false
browser.places.smartBookmarksVersion: 6
browser.sessionstore.upgradeBackup.latestBuildID: 20140506152807
browser.startup.homepage: about:blank
browser.startup.homepage_override.buildID: 20140506152807
browser.startup.homepage_override.mstone: 29.0.1
browser.tabs.drawInTitlebar: false
browser.tabs.onTop: false
dom.mozApps.used: true
extensions.lastAppVersion: 29.0.1
font.default.x-western: sans-serif
font.internaluseonly.changed: true
font.name.sans-serif.x-western: Montserrat
font.name.serif.x-western: Montserrat
network.cookie.prefsMigrated: true
network.dnsCacheEntries: 0
network.dnsCacheExpiration: 0
places.database.lastMaintenance: 1400218745
places.history.expiration.transient_current_max_pages: 104858
plugin.disable_full_page_plugin_for_types: application/pdf
plugin.importedState: true
print.printer_\\tina\Kajan_HP_LJ_P2055.print_bgcolor: false
print.printer_\\tina\Kajan_HP_LJ_P2055.print_bgimages: false
print.printer_\\tina\Kajan_HP_LJ_P2055.print_colorspace:
print.printer_\\tina\Kajan_HP_LJ_P2055.print_command:
print.printer_\\tina\Kajan_HP_LJ_P2055.print_downloadfonts: false
print.printer_\\tina\Kajan_HP_LJ_P2055.print_duplex: -983728976
print.printer_\\tina\Kajan_HP_LJ_P2055.print_edge_bottom: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_edge_left: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_edge_right: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_edge_top: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_evenpages: true
print.printer_\\tina\Kajan_HP_LJ_P2055.print_footercenter:
print.printer_\\tina\Kajan_HP_LJ_P2055.print_footerleft: &PT
print.printer_\\tina\Kajan_HP_LJ_P2055.print_footerright: &D
print.printer_\\tina\Kajan_HP_LJ_P2055.print_headercenter:
print.printer_\\tina\Kajan_HP_LJ_P2055.print_headerleft: &T
print.printer_\\tina\Kajan_HP_LJ_P2055.print_headerright: &U
print.printer_\\tina\Kajan_HP_LJ_P2055.print_in_color: true
print.printer_\\tina\Kajan_HP_LJ_P2055.print_margin_bottom: 0.5
print.printer_\\tina\Kajan_HP_LJ_P2055.print_margin_left: 0.5
print.printer_\\tina\Kajan_HP_LJ_P2055.print_margin_right: 0.5
print.printer_\\tina\Kajan_HP_LJ_P2055.print_margin_top: 0.5
print.printer_\\tina\Kajan_HP_LJ_P2055.print_oddpages: true
print.printer_\\tina\Kajan_HP_LJ_P2055.print_orientation: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_page_delay: 50
print.printer_\\tina\Kajan_HP_LJ_P2055.print_paper_data: 9
print.printer_\\tina\Kajan_HP_LJ_P2055.print_paper_height: 11,00
print.printer_\\tina\Kajan_HP_LJ_P2055.print_paper_name:
print.printer_\\tina\Kajan_HP_LJ_P2055.print_paper_size_type: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_paper_size_unit: 1
print.printer_\\tina\Kajan_HP_LJ_P2055.print_paper_width: 8,50
print.printer_\\tina\Kajan_HP_LJ_P2055.print_plex_name:
print.printer_\\tina\Kajan_HP_LJ_P2055.print_resolution: 1
print.printer_\\tina\Kajan_HP_LJ_P2055.print_resolution_name:
print.printer_\\tina\Kajan_HP_LJ_P2055.print_reversed: false
print.printer_\\tina\Kajan_HP_LJ_P2055.print_scaling: 1,00
print.printer_\\tina\Kajan_HP_LJ_P2055.print_shrink_to_fit: true
print.printer_\\tina\Kajan_HP_LJ_P2055.print_to_file: false
print.printer_\\tina\Kajan_HP_LJ_P2055.print_unwriteable_margin_bottom: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_unwriteable_margin_left: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_unwriteable_margin_right: 0
print.printer_\\tina\Kajan_HP_LJ_P2055.print_unwriteable_margin_top: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_bgcolor: false
print.printer_\\tina\NRG_MP_C3501_PS.print_bgimages: false
print.printer_\\tina\NRG_MP_C3501_PS.print_colorspace:
print.printer_\\tina\NRG_MP_C3501_PS.print_command:
print.printer_\\tina\NRG_MP_C3501_PS.print_downloadfonts: false
print.printer_\\tina\NRG_MP_C3501_PS.print_duplex: -983728976
print.printer_\\tina\NRG_MP_C3501_PS.print_edge_bottom: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_edge_left: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_edge_right: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_edge_top: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_evenpages: true
print.printer_\\tina\NRG_MP_C3501_PS.print_footercenter:
print.printer_\\tina\NRG_MP_C3501_PS.print_footerleft: &PT
print.printer_\\tina\NRG_MP_C3501_PS.print_footerright: &D
print.printer_\\tina\NRG_MP_C3501_PS.print_headercenter:
print.printer_\\tina\NRG_MP_C3501_PS.print_headerleft: &T
print.printer_\\tina\NRG_MP_C3501_PS.print_headerright: &U
print.printer_\\tina\NRG_MP_C3501_PS.print_in_color: true
print.printer_\\tina\NRG_MP_C3501_PS.print_margin_bottom: 0.5
print.printer_\\tina\NRG_MP_C3501_PS.print_margin_left: 0.5
print.printer_\\tina\NRG_MP_C3501_PS.print_margin_right: 0.5
print.printer_\\tina\NRG_MP_C3501_PS.print_margin_top: 0.5
print.printer_\\tina\NRG_MP_C3501_PS.print_oddpages: true
print.printer_\\tina\NRG_MP_C3501_PS.print_orientation: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_page_delay: 50
print.printer_\\tina\NRG_MP_C3501_PS.print_paper_data: 9
print.printer_\\tina\NRG_MP_C3501_PS.print_paper_height: 11,00
print.printer_\\tina\NRG_MP_C3501_PS.print_paper_name:
print.printer_\\tina\NRG_MP_C3501_PS.print_paper_size_type: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_paper_size_unit: 1
print.printer_\\tina\NRG_MP_C3501_PS.print_paper_width: 8,50
print.printer_\\tina\NRG_MP_C3501_PS.print_plex_name:
print.printer_\\tina\NRG_MP_C3501_PS.print_resolution: 1
print.printer_\\tina\NRG_MP_C3501_PS.print_resolution_name:
print.printer_\\tina\NRG_MP_C3501_PS.print_reversed: false
print.printer_\\tina\NRG_MP_C3501_PS.print_scaling: 1,00
print.printer_\\tina\NRG_MP_C3501_PS.print_shrink_to_fit: true
print.printer_\\tina\NRG_MP_C3501_PS.print_to_file: false
print.printer_\\tina\NRG_MP_C3501_PS.print_unwriteable_margin_bottom: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_unwriteable_margin_left: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_unwriteable_margin_right: 0
print.printer_\\tina\NRG_MP_C3501_PS.print_unwriteable_margin_top: 0
privacy.cpd.siteSettings: true
privacy.sanitize.migrateFx3Prefs: true
privacy.sanitize.timeSpan: 0
storage.vacuum.last.index: 1
storage.vacuum.last.places.sqlite: 1399495195
user.js-inställningar
Din profilmapp innehåller en user.js-fil som inkluderar inställningar som inte har skapats av Firefox.
Grafik
Adapter-RAM: 512
Adapterbeskrivning: NVIDIA GeForce 7950 GT
Adapterdrivrutin: nvd3dumx,nvd3dum
ClearType-parametrar: D [ Gamma: 2200 Pixel Structure: R ClearType Level: 100 Enhanced Contrast: 50 ] D [ Gamma: 2200 Pixel Structure: R ClearType Level: 100 Enhanced Contrast: 50 ]
DirectWrite aktiverat: false (6.2.9200.16492)
Drivrutinsdatum: 1-31-2013
Drivrutinsversion: 9.18.13.783
Enhets-ID: 0x0295
GPU #2 aktiv: false
Grafikaccelererade fönster: 1/1 Direct3D 9
Leverantörs-ID: 0x10de
WebGL-renderare: Google Inc. -- ANGLE (NVIDIA GeForce 7950 GT Direct3D9Ex vs_3_0 ps_3_0)
windowLayerManagerRemote: false
AzureCanvasBackend: skia
AzureContentBackend: cairo
AzureFallbackCanvasBackend: cairo
AzureSkiaAccelerated: 0
JavaScript
Incremental GC: true
Tillgänglighet
Aktiverad: false
Förhindra tillgänglighet: 0
Biblioteksversioner
NSPR
Förväntad minimiversion: 4.10.3
Version som används: 4.10.3
NSS
Förväntad minimiversion: 3.16 Basic ECC
Version som används: 3.16 Basic ECC
NSSSMIME
Förväntad minimiversion: 3.16 Basic ECC
Version som används: 3.16 Basic ECC
NSSSSL
Förväntad minimiversion: 3.16 Basic ECC
Version som används: 3.16 Basic ECC
NSSUTIL
Förväntad minimiversion: 3.16
Version som används: 3.16

Many site issues can be caused by corrupt cookies or cache. 
Clear the Cache 
'''''Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"'''''
 and 
Remove Cookies '''''Firefox/Tools > Options > Privacy.''''' 
Under '''History''', select Firefox will '''Use Custom Settings'''. 
There is a button on the right side called '''Show Cookies'''. 
If there is still a problem,
'''''[https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode Start Firefox in Safe Mode]'''''
 While you are in safe mode; 
'''''Firefox Options > Advanced > General'''''. 
Look for and turn off '''Use Hardware Acceleration'''. 
Poke around safe web sites and see if there is still a problem. Then restart.
 
This may or may not help you; 
'''''[https://addons.mozilla.org/en-US/firefox/addon/nosquint/?src=external-Add-ons_Manager_Context_Menu-extension NoSquint]''''' 
NoSquint allows you to adjust the text-only and full-page (both text and images) zoom levels as well as color settings both globally (for all sites) and per site.

Problem with installing Paint shop Pro photo X2 on with Vista

Trying to install Paint shop photo x2 on my note book but at the end of the installation it freezes and there seems to be some problem with "registering"...
Corel (supplier of paint shop) now advised me to change some drivers but the links I received are for XP or lower versions.
Is there anybody who had the same problem and find the solution?
i have tried already several things (like shutting down norton, msconfig changes etc)....
Thanks for your help!

Hi
I have noticed that not all programs and applications are compatible and support the Vista OS. Did you check if this program supports Vista?
I think this should be clarified firstly.
I would recommend contacting the Paint shop Pro manufacture for the troubleshooting.
Good luck

Problem with fingerprint on HP Pro x2 612 g1

hi
i'm having problem with fingerprint on my HP Pro x2 612 g1.. i've installed all of the drivers which i have downloaded using your site and i can see fingerprint option but there is no add button under it.. i'm using windows 8.1 pro 64bit
need your help..
thanks

Here are the direct links to the fingerprint drivers:
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=7268930&swItemId=ob_138590_1&swEnvOid=415...
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=7268930&swItemId=ob_134806_1&swEnvOid=415...
Let me know if that helps.
-Chris
I work for HP.
Support Forums are now on your mobile phone: http://m.hp.com/supportforum

Problem with a MSI-6163 PRO

Similar Messages

Maybe you are looking for