Problem with access to SMTP, IMAP, POP3 protocols in CAS 2013.

Hi,
we have problem with access thgrough SMTP, IMAP, POP3 protocols in CAS 2013.
If I test connection to SMTP 25 port from other computer, session end quickly.
Test from CAS2013 to localhost or public IP is OK (similar also for IMAP and POP3).
Receive connectors are with defaults settings, firewall is disabled.
Service Microsoft Frontend Transport Services restarted, but no success.
Certificate is assigned to IMAP, POP3, SMTP, IIS.
IIS and HTTP(s), protocols are OK. Clients can connects only thgrough web, mobile (ActiveSync), or with Outlook with proxy.
Do you have some tip, what to test?
If I create new testing receive connector on port 26 for anonymous, behaviour is same, quick disconnecting.
Thank's Mirek

Hi,
Pleaser try to use the following link to test your STMP/POP/IMAP e-mail, and check the test if successful:
https://testconnectivity.microsoft.com/
If unsuccessful, please check the test result, it will tell us what caused the problem.
Thanks.
Niko Cheng
TechNet Community Support

Similar Messages

Is there a problem with Apple Mail using IMAP

Is there a problem with Apple Mail using IMAP? Having a problem syncing to our mail server: doesn't sync properly when multiple devices use same mail acct. Spoken w/ mail hosting provider who says Apple Mail doesn't follow IMAP protocol properly leaving Apple Mail users to experience a variety of problems when connecting to IMAP accounts. Among them:
- Improper syncing
- Proliferation of drafts during composition of an email.
- Connections on the mail host do not close automatically and proliferate over time until the host rejects further connection requests.
Hosting provider goes on to suggest turning off IDLE command. In my experience turning this feature off did not improve the situation. In fact, it created a few.
Question: Is the hosting provider correct in faulting Apple Mail?
Been fielding the question with a number of people. I'm aware of three people who are experiencing similar problems, each using different mail hosts. Tech reps at inmotionhosting.com and nexcess.com point the finger at a Apple Mail, along with an IT specialist in Los Angeles, CA, and a tech support rep at an Apple Store in Arizona who said that Apple and Google mail are aware of and coordinating to resolve the problem.
Anyone out there have any insights into this?

Is there a problem with Apple Mail using IMAP? Having a problem syncing to our mail server: doesn't sync properly when multiple devices use same mail acct. Spoken w/ mail hosting provider who says Apple Mail doesn't follow IMAP protocol properly leaving Apple Mail users to experience a variety of problems when connecting to IMAP accounts. Among them:
- Improper syncing
- Proliferation of drafts during composition of an email.
- Connections on the mail host do not close automatically and proliferate over time until the host rejects further connection requests.
Hosting provider goes on to suggest turning off IDLE command. In my experience turning this feature off did not improve the situation. In fact, it created a few.
Question: Is the hosting provider correct in faulting Apple Mail?
Been fielding the question with a number of people. I'm aware of three people who are experiencing similar problems, each using different mail hosts. Tech reps at inmotionhosting.com and nexcess.com point the finger at a Apple Mail, along with an IT specialist in Los Angeles, CA, and a tech support rep at an Apple Store in Arizona who said that Apple and Google mail are aware of and coordinating to resolve the problem.
Anyone out there have any insights into this?

Problem with Access Policies (create multiple resources)

I'm having a problem with Access Policies:
The first policy must create a resource.
And the following policies should create childs on the resource.
The problem here is that when policies will add the childs, the resource is not provisioned yet.
And then each one will create a resource but i just want one resource with the childs.
When the resource is already provisioned, the policies update this resource properly.
How can I fix this?
tks

Ricardo,
I had a similar problem. In a post-process handler I was managing the user membership in specific roles through the removeMemberUser and the addMemberUser of the tcGroupOperationsIntf class.
The last parameter of this method was a boolean which, when true, would automatically trigger the access policies programmatically in the post-process.
The problem is that there also is an OOTB event handler for triggering access policies, so I was basically triggering the access policies twice and duplicated resources were appearing.
Hope this helps.
Cheers

Problem with access to SipFactory from jsp-pages in JBoss environment

Hello!
I have an installation of the OCMS 10.1.3.3. deployed into a JBoss (jboss-4.0.5.GA) environment. Unfortunately I have a problem with accessing the SipFactory from a jps-page. Encouraged by the "messagesender" example I tried to get an instance of SipFactory from my jsp-page simply by calling:
SipFactory sipFactory = (SipFactory) application.getAttribute(SipServlet.SIP_FACTORY);
But unfortunately there seems to be no attribute "SipServlet.SIP_FACTORY" and I only get a null pointer. I have also tried running that code in the orignal messagesender example but it didn't work either. So I wonder if this should definetely work in a JBoss environment or if this might be a known problem. Is there anything that I could check/do regarding this problem? I suppose there must be an oracle module which should take care of making the SipFactory availabe after it is deployed. Perhaps something went wrong during the deployment?!
Best regards,
Tim

Hi
On JBoss, OCMS does not support converge applications.
I.e the SipFactory can be retrieved from the servlet context when running on OC4J.
Instead the SipFactory can be found in JNDI as described in the Developer's Guide:
"External Access to SIP Servlets
To enable convergent applications between SIP and HTTP, the OCMS Container allows you to get access to the javax.servlet.sip.SipFactory by looking it up through JNDI. The SIP Factory will be registered under the same name as the display name of your SIP servlet as illustrated in Example 2–12. The <display-name> in the sip.xml in this case must be "My sip app".
Example 2–12 Accessing the Data for a SIP Session through JNDI
InitialContext ic = new InitialContext();
SipFactory sipFactory = (SipFactory)ic.lookup("sip/My sip app");"
Cheers
Lucas Persson

I have problem with Access Connections on L412 after that utilyty upgrade

I have problem with Access Connections on L412 after that utilyty upgrade in early August. Windows 7 Ultimate/x64.
It stops connecting to WPA2 Enterprise (AES-CCMP), Microsoft PEAP, no server cert, with any credentials I try to use. The same account(s) works with native Intel manager on other notebooks and on mobile devices. I lost the wireless connectivity to enterprise WiFi network.
And, after deinstallation of Access Connections, the inability to connect keeped intact with native Win7 WiFi management.
I think, something was broken in Access Connections 5.83 Build 83C753WW and some registry settings/ dll modules were altered but not returned to normal after deinstall.

Access Connections is definitely broken for WPA encryption. Both versions 5.02 and 5.84 fail for me. If I use the Windows XP wireless configuration instead of Access Connections, everything works.
Does anyone know how to report this to Lenovo? I chased links around the web site but couldn't find a place.

Why do i have a problem with accessing images in adobe muse

why do i have a problem with accessing images in adobe muse ??????!!!!!
i need heeeeeelp ASAP
pleeeeease

I am on the begining stages with constructing the web so i do not have yet URL. The problem is i can not insert any image any way. Whether by fill a browser or by place image, i have the same issue. All the images with all image's format unable to be selected and it is turned off
I really need help plz
Is there any info i can supply that would help you figiring out the problem ??

Can Play iTunes Library from PC on MacBook Air but cannot import, problem with access rights?

I can play Itunes library from Windows Vista PC on my MacBook Air using homeshare but cannot import the library . Error message is problem with access rights. Latest OS and Itunes installed. Both computers registered with Apple on same Apple ID. Wifi Router turned on and off. Still does not allow importing. Any suggestions please?

Might be an alternative for you here > iTunes: How to move your music to a new computer

If anybody have a problem with connection to smtp server from iPhone

If anybody have a problem with connection to smtp server just add new server
Seetings → Mail, Contacts, Calendars → User Me account → Account → Under Advanced choose Mail → SMTP → Add Server
smtp.me.com
user name ([email protected])
password
Apple, i am in love with your product, please fix this so we could injoy it even more.

Might be something to help you here > iCloud: Mail server information

Just wondering if anyone has a problem with accessing iTunes store. have iTunes installed but can't bring up the store home page?

Just wondering if anyone has a problem with accessing iTunes store. have iTunes installed but can't bring up the store home page?

i have the same problem! Safari won't work either. Can anyone help please? I have completely restored my computer trying to fix this and it still won't work! I have a 2 month old alienware laptop running windows 7

HELP!! asa 5505 8.4(5) problem with port forwarding-smtp

Hi I am having a big problem with port forwarding on my asa. I am trying to forward smtp through the asa to my mail server.
my mail server ip is 10.0.0.2 and my outside interface is 80.80.80.80 , the ASA is setup with pppoe (I get internet access no problem and that seems fine)
When I run a trace i get "(ACL-Drop) - flow is deied by configured rule"
below is my config file , any help would be appreciated
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISPDsl
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_SMTP
host 10.0.0.2
access-list outside_access_in extended permit tcp any object server_SMTP eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network server_SMTP
nat (inside,outside) static interface service tcp smtp smtp
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c5570d7ddffd46c528a76e515e65f366
: end

Hi Jennifer
I have removed that nat line as suggested but still no joy.
here is my current config
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISP
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_Mail
host 10.0.0.2
access-list outside_access_in extended permit tcp any object Server_Mail eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network Server_Mail
nat (inside,outside) static interface service tcp smtp smtp
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f3bd954d1f9499595aab4f9da8c15795
: end
also here is the packet trace
and my acl
Thanks

Problem with access to Ironport C370

Hi,
We have C370 (upgraded to last version) configured and everythings work fine! But one day, from some reason, we cant access Ironport via HTTPS, HTTP and SSH, only works ping. Problem with network is not because we try access Ironport direct from Managment port. After reboot, then access is fine. Please can you tell me how I can figure out what was a problem, which logs I need to analyze.... Why I could not access to ironport via HTTP/S, SSH?

I dont think that problem is exchange because problem also was about accessing to ironport, I think that some problem is on ironport:
Tue Apr 16 16:08:52 2013 Info: New SMTP DCID 15929874 interface 172.30.20.4 address 65.55.37.88 port 25
Tue Apr 16 16:08:52 2013 Info: ICID 5276886 Receiving Failed: Out of Memory
Tue Apr 16 16:08:52 2013 Info: ICID 5276886 close
Tue Apr 16 16:08:53 2013 Info: Delayed: DCID 15929873 MID 11206813 to RID 0 - 4.1.0 - Unknown address error ('450', ['too many connections from your IP (rate controlled)']) []
Tue Apr 16 16:08:53 2013 Info: MID 11206813 to RID [0] pending till Tue Apr 16 17:08:53 2013 [Default]
Tue Apr 16 16:08:53 2013 Info: Connection Error: DCID 15929873 domain: shop.com IP: 216.136.0.12 port: 25 details: EOF interface: 172.30.20.4 reason: network error
Tue Apr 16 16:08:53 2013 Info: ICID 5276890 Receiving Failed: Out of Memory
Tue Apr 16 16:08:53 2013 Info: ICID 5276890 close
Tue Apr 16 16:08:53 2013 Info: New SMTP DCID 15929875 interface 172.30.20.4 address 216.136.0.12 port 25
Tue Apr 16 16:08:53 2013 Info: Delivery start DCID 15929874 MID 11744351 to RID [0]
Tue Apr 16 16:08:53 2013 Info: New SMTP ICID 5276899 interface data (172.30.20.4) address 172.29.18.137 reverse dns host unknown verified no
Tue Apr 16 16:08:53 2013 Info: ICID 5276899 RELAY SG RELAY match 172.0.0.0/8 SBRS rfc1918
Tue Apr 16 16:08:53 2013 Info: Connection Error: DCID 15929874 domain: hotmail.com IP: 65.55.37.88 port: 25 details: 421-"RP-001 (COL0-MC2-F35) Unfortunately, some messages from 195.222.56.65 weren't sent. Please try again. We have limits for how many messages can be sent per hour and per day. You can also refer to http://mail.live.com/mail/troubleshooting.aspx#errors." interface: 172.30.20.4 reason: unexpected SMTP response
Tue Apr 16 16:08:53 2013 Info: Delayed: DCID 15929874 MID 11744351 to RID 0 - 4.3.2 - Not accepting messages at this time ('421', ["RP-001 (COL0-MC2-F35) Unfortunately, some messages from 195.222.56.65 weren't sent. Please try again. We have limits for how many messages can be sent per hour and per day. You can also refer to http://mail.live.com/mail/troubleshooting.aspx#errors."]) []

Problems with server settings for IMAP account

hi
i am trying to configure Mail to work with an IMAP account. i can receive messages OK on this account, but cannot send mail. when i try to send mail i get an error message "sender verify failed".
there was an automated process for adding the account to mail which i installed, and got the following settings:
outgoing mail server: mail.soterianetwork.org
server port: 26
authentication: password
username: soteria
password: ****** (the password is correct)
the error message i get is 'sender verify failed'.
i have also tried ports 25 and 587 without success.
on the web based control panel for the mail account it says: Be sure to enable SMTP Authentication in your E-mail client or you may not be able to send mail.
not sure if i have done this. i have tried changing the outgoing mail server to smtp.soterianetwork.org, still without success
i would be grateful for some help to get this set up correctly
thanks
nick

it was a problem with the server. they changed some settings and all is working fine

Problems with mail connecting to IMAP since 10.5.2

Hi,
Since upgrading to 10.5.2, I can not access my IMAP mail server anymore, it will sit there for a long time with the spinning wheel trying to sync with the mail server. After a very long time I will get me an error message that IMAP server is not available. I have Entourage 2007 installed as well and that can access the mail server with no problem with exact same setting.
Anyone else had this issue, can I forced mail to rebuild the mailbox, I have a lot of mail stored in the mailbox, online and on my mac so I can not afford to loose any mail.
Mail also seem to hang up on me a lot and I need to use Force Quit.
Thanks
Jaco

for me it doesn't exactly hang, a.k.a not responding, but it won't quit. I have to use force.

Problem with yahoo! SMTP POP server mail account on new upgraded iphone 4.3.5

PLEASE HELP!
I am a California AT&T wireless customer with a new iphone 4 on the iOS 4.3.5 upgraded system and suddenly I am unable to successfully add my Yahoo! email account and have it configured to send/receive my emails. I was able to successfully add my gmail and Microsoft exchange server account, but only problems with the Yahoo! I checked all the settings, have done several add/delete accounts, restore network settings, and retry/reboots, to no avail. This is a seriously annoying problem, it worked with the pre-upgraded older version fine without any problems ever. I continually get the same error message: SERVER UNAVAILABLE, please try again later.
I know this error is inaccurate because all my other email accounts work fine as well as Safari and all other internet connections and apps. It is not a phone thing, it is some yahoo and upgraded software incompatibility issue that no one seems to have resolved yet.
This is a SMTP PUSH POP account, and I have literally tried everything. I have tried all the fixes while connected to wifi, and then tried them just via my 3G cell network connection. I read on a message board about turning on/off SSL, could someone tell me how to do that? When I go into to:
settings>mail accounts>outgoing mail server SMTP>Yahoo! SMTP, everything is grayed out and I can't change any ports or SSL.
When I try to manually add a server, which I was told was a fix, I don't know what to type into the host name. Does anyone know how to help?
I have seen this problems on numerous message boards, even in the UK. I contacted Apple Support, with no success in resolving this problem, had an open case for several days contacted several supervisor personnel, all advised me to contact Yahoo! who do not offer customer care via telephone only online, and nothing there helped to resolve my issue.
PLEASE, PLEASE HELP!
THANKS

Yahoo's servers have been having problems off and on now for close to a month if not longer. There's not much you can do about it except talk to Yahoo, which is kind of like beating your head against a wall. They've had problems like this off and on since as far back as the mid 90's. I gave up on them long ago. Just convert to something else and dump them. It's not worth the headache.

Connector problem with access enforcer

Hi Guys,
I am facing a really strange problem with my connectors.
We have a test installation of GRC which was down for about 3 months.
During this time we migrated our central SLD to another system so I needed to change the connection after getting the system up again.
Anyhow I still can't modify, test or even create a new connector for access enforcer.
The only error I get is "Action failed".
I tried to analyze the logs but found no help there too.
2007-06-18 20:41:56,833 [SAPEngine_Application_Thread[impl:3]_4] ERROR java.lang.NullPointerException
java.lang.NullPointerException
     at com.virsa.ae.dao.sqlj.SAPConnectorDAO.iterToDTO(SAPConnectorDAO.sqlj:75)
     at com.virsa.ae.dao.sqlj.SAPConnectorDAO.findByConnectorName(SAPConnectorDAO.sqlj:15)
     at com.virsa.ae.configuration.bo.ConnectorsBO.findSAPConnectorDetails(ConnectorsBO.java:76)
     at com.virsa.ae.configuration.actions.ManageConnectorsAction.testConnection(ManageConnectorsAction.java:163)
     at com.virsa.ae.configuration.actions.ManageConnectorsAction.execute(ManageConnectorsAction.java:66)
     at com.virsa.ae.commons.utils.framework.NavigationEngine.execute(NavigationEngine.java:229)
     at com.virsa.ae.commons.utils.framework.servlet.AEFrameworkServlet.service(AEFrameworkServlet.java:412)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java(Compiled Code))
     at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:390)
     at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:264)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:347)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:325)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:887)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:241)
     at com.sap.engine.services.httpserver.server.Client.handle(Client.java:92)
     at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:148)
     at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java(Compiled Code))
     at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java(Compiled Code))
     at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java(Compiled Code))
     at java.security.AccessController.doPrivileged1(Native Method)
     at java.security.AccessController.doPrivileged(AccessController.java(Compiled Code))
     at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java(Compiled Code))
     at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java(Compiled Code))
Did anybody here face a problem like that?
Kind regards,
Bastian
Message was edited by:
        Bastian Schneider
Message was edited by:
        Bastian Schneider

I had a simular problem with CC and I had to contact SAP. They gave me a script to run against the database that remove the connector. The problem seemed somewhat common for CC 5.1. Not sure if this applies to AE.

Problem with access to SMTP, IMAP, POP3 protocols in CAS 2013.

Similar Messages

Maybe you are looking for