Problem with Autofill and adding songs

I just purchased a second generation iPod shuffle. When I first loaded my iPod all of the songs in my itunes library automatically loaded onto my shuffle. The problem is, that I now cannot add or delete songs. I keep getting the error "the iPod cannot be synced. The disk could not be read from or written to".
After reading some posts I downloaded the reset software and reset my iPod, but again I had the same problems. What I did to resolve this was to delete songs from my Library that I did not want on my iPod, then I reset it and the songs in my library automatically loaded again.
Still I cannot change the order, or add songs, or I get the same error message. Can anyone help?
  Windows XP  

In order to stop the iPod getting filled automatically, you need to follow the steps below.
Click on the iPod icon on the source list under "Devices” and to the right we will see the settings/contents tab. Under the "settings" tab click on the "Restore" button.
Once it is restored, we will see a "iPod setup assistant" where you can name the iPod. Just below that you will get an option to "Automatically choose songs for the iPod" . Uncheck that option and click on OK.
=================================================
For the error mesage "Disk cannot be read from or written to" when syncing iPod you need to folow the below article and the links.
http://docs.info.apple.com/article.html?artnum=301267
===============================================
Moreover with Windows XP we need to have service pack 2 installed as its the basic system requirement for iPod and iTunes.
Click on the START button, click on RUN and type "winver" and then press ENTER.
You will see "Service Pack" (SP) followed by a number in a pop up window.
If you do not have SP2 , I would suggest you to install the "service pack 2" for the operating system from the below URL:
http://www.microsoft.com/windowsxp/sp2/default.mspx
===============================================

Similar Messages

  • A problem with Itunes and adding music to library

    I've been using my Ipod touch for about a month now (recently purchased). I first connected my Ipod to my laptop, because my desktop needed a format and reinstall of the OS, so I wanted to be slightly organized with it. I finally got around to formatting the desktop to WinXP pro, and have all my programs installed successfully.
    Here's the issue:
    With my laptop, I could start Itunes, and I did NOT have every song I have as my library, only a few songs that I personally selected and added to library (by clicking on "CTRL+Highligh" or File-->Add file to library). When I did that, I could hold down CTRL and highlight up to 15-20 songs at once, and have them show up in my library as added, then sync them to my Touch.
    Since coming to my desktop with my Ipod, and moving all my music from my laptop over to my desktops C: drive, I've hooked up my Ipod and (of course installed Itunes) authorized my desktop for my Touch.
    I begain selecting the music I wanted...My directory setup is as follows:
    My Music: folders inside of
    Itunes directory
    Mp3 Directory
    My Itunes settings are selected as My Music-->Itunes as the folder. I open Itunes, select add song to library, and it only allows me to highlight UP to 5 songs at once and add them. Any number between 1 and 5 songs will add to my library just fine. If i try to select over 5 songs, like 6-20 songs at once (using CTRL) it does nothing, and doesnt place any of the selected songs in my library. It will allow me to select individual songs just fine, and like I said, I can select UP TO 5 songs, highlighted with CTRL, and they show up just fine (all 5 songs will show in the library.)
    Any number of songs selected with CTRL over 5, does nothing.
    I dont understand why, when I used this very technique on my laptop, and I could select up to 30 songs at once (using ctrl+highlight) and they would ALL show up as they are supposed to. Everything is nearly the same on here, my settings are all pretty much the same as my laptop's settings were...anyone have any ideas? this has been bugging me all morning, and I've spent so much time fooling with it that I only have 56 songs out of 6,000 on my Ipod touch (I also decided to rid myself of music I didnt listen to and restored/formatted my ipod so I could start over)...I need more than 56 songs, but I dont want to do them 1 or 2 at a time, then go back and have to hit CTRL+O or File--->add file to library.
    What causes me to be limited to 5 or less songs per time to add to my library?

    Because I wasn't aware that the library could be "taken" from pc to pc. The processor on my desktop is also hyper-threaded, which simulates it having 2 processors..and moving file NAMES, not moving the files into the library is NOT a processor intensive function. It's actually just taking the file location - directory, and name, and making it show in the library..not moving the actual file itself and making a copy of it in the Itunes folder. I do NOT allow itunes to make copies of files that it keeps in the library (I uncheck allow Itunes to organize and make copies of files added to library).
    So adding to my library is as simple as making the library show the file name, and pointing to the location on disk, not actually making a copy of the file in the background and placing it into a folder inside the Itunes folder.
    Had I KNOWN I could take my library off the desktop and move it, I would've made it easier on myself, but I thought I posted that I just recently bought this Ipod touch (about a month ago).

  • Speaker problem with t420i and adding a new graphics card question

    I bought a t420i about a month ago and noticed that the speakers could not properly handle muliple sounds at once.  What happens is that, say in a music video, the music plays loud and clear, but once the lyrics start the background music fades a bit to about 85% of it's original volume.  I had returned the laptop because of this problem but the replacement I got has the SAME exact problem.
    In case im not clear, try this example.  You know the beeping noise you get when you press an incompatible set of keys?  ( like g, h, and b).  When I have this noise going simultaneously with a song, the song's sound fades a bit.
    This does not happen with headphones, therefore i believe the problem is with the way the speakers are programmed.
    Also, if I bought a t420 with just integrated graphics, could I still add a new graphics card?  Or can you only add a new graphics card to a thinkpad that initially comes with discrete graphics?

    I think the main purpose of the nvs4200m is the ability to use three displays (internal + 2 external). Additionally, nVidia has better driver support for games so even though it is around the same speed, the drivers are better. 
    The shared ram is still used, unless you disable the HD3000 in the BIOS and run with only the nvs4200m at all times. 
    When asking for help, post your question in the forum. Remember to include your system type, model number and OS. Do not post your serial number.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help others with the same question in the future.
    My TPs: Twist 2HU: i5-3317U Win 8 Pro, 4GB RAM 250GB Samsung 840 | T420 4177CTO: i5-2520M, HD+, Win 7 Pro x64, 8GB RAM, Optimus, 160GB Intel 320 SSD, Intel 6300 WiFi, BT 3.0 | T400 2764CTO: P8700, WXGA, Win 7 Ult x64, AMD 3470, 8GB RAM, 64GB Samsung SSD, BT, Intel 5300 WiFi | A20m 14.1" PIII 500 (retired). Monitors: 2x Dell U2211h IPS 100% sRGB calibrated w/ Spyder3.

  • Problems with conference calls(adding and merging calls) after upgrade to ios 8.1.2 on iphone 5s

    I am having weird problem intermittently with adding calls or merging them or swapping them. The issue happens 8 out of 10 times whenever I try to do a conference call. This issue came up after I upgraded to 8,1.2. Never experienced this in 8.1.1 or previous version.
    Some of the scenarios that I have experienced is:
    1. While on the call, when I try to add a new contact, it just doesn't dial the second number.
    2. Sometimes the second number gets dialed, cannot merge the calls.
    3. After talking to the second person, cannot go back to the first call.
    I am very sure that this is not a carrier issue as it worked flawlessly before upgrade.
    Anyone experienced this before? Any suggestions?

    Thanks for the above infromation. I did a complete restore of my iphone through iTunes connecting it to my computer via cable. iOS8.1.3 was re-installed. I then added back my settings and data which were backed up prior to restoring the phone. I still have the same issue with conferencing and adding a third caller. When I hit the [+] box, the existing caller is not put on hold. The phone appears to be making a call but it is not dialing to the 3rd party. Shortly thereafter, the Merge icon appears but there is no active call to merge with. I have tried this several times using my wife's iPhone and our home phone to set up a 3-way call. I know it is not working because the 3rd phone (our home phone) does not ring. Is this a hardware problem? My wife's iPhone 6 works with no problem and was purchased the same time I purchased my iPhone 6. Probably time for a visit to the Apple Store unless there is another solution.
    iPhone 6; iOS 8.1.3; Carrier: Verizon

  • Does anybody know if Windows 8 is causing a problem with iTunes?   Many songs on my old iPod are now missing in my iTunes library and I can't find them anywhere.  Also, I have a new iPod and am afraid of using it for fear of something else going wrong.

    Does anybody know if Windows 8 is causing a problem with iTunes?  Many songs on my old iPod are now missing in my iTunes library and I can't find them anywhere.  .  Also, I have a new iPod and am afraid of using it for fear of something else going wrong.

    Try assigning Queen as the Album Artist on the compilations in iTunes on your computer.

  • Problem with Send and Receive Emal In SAP System

    Hi gurus!
    I have a following quote:
    Dear !
    I have a problem with send and receive email in SAP system following :
    I want to test send and receive email in local network at my company. I
    had two server
    Server 1 : I setup Exchange Mail Server 2007 with domain controller is
    fes.com
    Server 2 : I setup SAP ERP ECC 6.0
    On Server 1 : I created 2 account ( u1Afes.com and u2Afes.com ) and then I tested send and receive email between u1 and u2 in local network through Microsoft Outlook 2007 -> OK
    and then
    On Server 2: I had configured send and receive email on SAP system
    through tcode SBWP, SCOT and SOST as Note 455140 - "Configuration of
    e-mail, fax, paging or SMS using SMTP"
    for example :
    I logged in SAP system with user Basis01 (with email u1Afes.com ) -> then,using tcode SBWP -> new message -> send to u2Afes.com with Internet Mail type and then status message with green light -> sending ok
    and then I have used Microsoft Outlook 2007, I logged with account u2 ->check email -> Ok. I saw message which send from u1
    Finally, My problem is how can receive mail in SAP system without using Microsoft Outlook
    For example:
    Login system SAP with Basis01 account (with  u1Afes.com ) -> tcode SBWP ->New Message -> send to u2Afes.com
    and then
    Login system SAP with Basis02 account (with u2Afes.com ) -> tcode ??? ->
    To receive email from Basis01 (with u1Afes.com )
    Please help me now
    Thanks
    I replace "@" with "A" because of banning email of this forum.
    This quote is about sending email in local network. And we can't receive any email from the outside email address. Addition if I wanna send email to internal email in Internet (we've just tried with email address in local network) What should I config in SAP and Exchange ?
    By the way, Is SAP Server IP added to Relay Agent for sending or receiving mail ?
    Regards
    An NLP
    Edited by: An NLP on Apr 6, 2010 7:03 PM

    Hi,
    This problem is a classic problem of mail routing via Exchange. Exchange like most mail servers use the domain part of the email address as a means to route mails. So I will make an assumption that your main company mail addrss is "User @ fes.com".
    So when you send a mail to the "User @ fes.com mail" address the mail is delivered to your Outlook mail address as this is the default route for company.
    (Q) So how do you get your Exchange server to relay the mail into the sending SAP system?
    (A) The easiest way would be to setup and unique mail domain for your SAP system. I always recommend "user @ client.sid.company.com" which in your case would be "u1 @ 100.PRD.fes.com". You can then instruct Exchange to send any emails addressed to 100.PRD.fes.com domain to your SAP system. Also using this format of address you can configure multiple mail connections into multiple SAP systems.
    (A) Another answer would be to enter the "Full" email address (LOcal and Domain part of address) into the routing rule for Exchange e.g. "U1 @ fes.com" so that all emails addressed to this user will be delivered into SAP. However this method requires a lot of Admin as you will have to update Exchange with ALL email address that need to receive emails. Also if your corporate mail address is "U1 @ fes.com" then all mails will be forwarded to SAP.
    I would definitely NOT recommend this method but the decision is up to you.
    P.S. The IP address of the SAP system is entered into the mail header of the email. This is standard practice in SMTP relay. You can suppress this header in Exchange
    Hope this helps
    Michael

  • Problem with trigger and entity in JHeadsart, JBO-25019

    Hi to all,
    I am using JDeveloper 10.1.2 and developing an application using ADF Business Components and JheadStart 10.1.2.27
    I have a problem with trigger and entity in JHeadsart
    I have 3 entity and 3 views
    DsitTelephoneView based on DsitTelephone entity based on DSIT_TELEPHONE database table.
    TelUoView based on TelUo entity based on TEL_UO database table.
    NewAnnuaireView based on NewAnnuaire entity based on NEW_ANNUAIRE database view.
    I am using JHS to create :
    A JHS table-form based on DsitTelephoneView
    A JHS table based on TelUoView
    A JHS table based on NewAnnuaireView
    LIB_POSTE is a :
    DSIT_TELEPHONE column
    TEL_UO column
    NEW_ANNUAIRE column
    NEW_ANNUAIRE database view is built from DSIT_TELEPHONE database table.
    Lib_poste is an updatable attribut in TelUo entity, DsitTelephone entity, NewAnnuaire entity.
    Lib_poste is upadated in JHS table based on TelUoView
    I added a trigger on my database shema « IAN » to upadate LIB_POSTE in DSIT_TELEPHONE database table :
    CREATE OR REPLACES TRIGGER “IAN”.TEL_UO_UPDATE_LIB_POSTE
    AFTER INSERT OR UPDATE OFF lib_poste ONE IAN.TEL_UO
    FOR EACH ROW
    BEGIN
    UPDATE DSIT_TELEPHONE T
    SET t.lib_poste = :new.lib_poste
    WHERE t.id_tel = :new.id_tel;
    END;
    When I change the lib_poste with the application :
    - the lib_poste in DSIT_TELEPHONE database table is correctly updated by trigger.
    - but in JHS table-form based on DsitTelephoneView the lib_poste is not updated. If I do a quicksearch it is updated.
    - in JHS table based on NewAnnuaireView the lib_poste is not updated. if I do a quicksearch, I have an error:
    oracle.jbo.RowAlreadyDeletedException: JBO-25019: The row of entity of the key oracle.jbo. Key [null 25588] is not found in NewAnnuaire.
    25588 is the primary key off row in NEW_ANNUAIRE whose lib_poste was updated by the trigger.
    It is as if it had lost the bond with the row in the entity.
    Could you help me please ?
    Regards
    Laurent

    The following example should help.
    SQL> create sequence workorders_seq
      2  start with 1
      3  increment by 1
      4  nocycle
      5  nocache;
    Sequence created.
    SQL> create table workorders(workorder_id number,
      2  description varchar2(30),
      3   created_date date default sysdate);
    Table created.
    SQL> CREATE OR REPLACE TRIGGER TIMESTAMP_CREATED
      2  BEFORE INSERT ON workorders
      3  FOR EACH ROW
      4  BEGIN
      5  SELECT workorders_seq.nextval
      6    INTO :new.workorder_id
      7    FROM dual;
      8  END;
      9  /
    Trigger created.
    SQL> ALTER SESSION SET NLS_DATE_FORMAT = 'DD-MON-YYYY HH24:MI:SS';
    Session altered.
    SQL> insert into workorders(description) values('test1');
    1 row created.
    SQL> insert into workorders(description) values('test2');
    1 row created.
    SQL> select * from workorders;
    WORKORDER_ID DESCRIPTION                    CREATED_DATE
               1 test1                          30-NOV-2004 15:30:34
               2 test2                          30-NOV-2004 15:30:42
    2 rows selected.

  • Problem with vista and 5.1

    problem with vista and 5. i install my old audigy 2 zs exp pro with DTT2500 speaker
    In my new pc.
    i install vista 64 and SBAX_PCDRV_LB_2_8_000 driver from creative site.
    when i go to control panel/sound and test the 5. surrund ' iget only the two front speaker.
    why is that?
    i try to play a song from vista folder "Distance" and i get all 5 +sub to play.
    do i miss something?
    is the test worg and with another test i can get all spedajer to work or the driver is not good?
    thanks for all you help
    last update...
    i can get 4 speaker when i use the fourpoint mode on the desktop theather 5. dtt2500 digital,
    but in movie mode i get only 2 front speaker.
    i use the digital out from the sound blaster.
    Message Edited by raflevi on 05-4-2009 02:38 [email protected]

    My apologies about not explaining further about disabling SPDIF passthrough. See the steps below to enable DDL encoding.
    ***Before proceeding please make sure that you've purchased, installed and activated the DDL pack***
    . Open Creative Audio Console, go to the Decoder tab to disable driver level encoding and enable SPDIF passthrough (this is done by selecting SPDIF passthrough or any similar option that enable the use of an external decoder) instead of using the built-in decoders.
    2. Open up your playback devices window (right click on the speaker icon on the taskbar and select playback devices) and set analog speakers (not SPDIF) as your default device. This is VERY IMPORTANT step, or else you get the "the device is busy" error when enbaling DDL encoding.
    3. In the Audio Console, select the Encoder tab and enable DLL encoding.
    Note:
    When DDL encoding is enabled, it makes exclusi've use of your SPDIF connection so, no passthrough is possible. The default output format when using DDL encoding is 48KHz/6 bits. If you make use of any AC3 audio filters (such as ac3filter/others included in codec packs/media player softwares) when DLL encoding is enabled, then please change their output device to analog speakers instead of SPDIF.
    To use back SPDIF passthrough (when playing back media with a pre-encoded audio source), open up Audio Console and disable DDL encoding and in the Playback Devices window change the default device to SPDIF. If you make use of any AC3 audio filters (such as ac3filter/others included in codec packs/media player softwares) then please change their output device back to SPDIF. You may also wish to change back your output format to 92KHz/24 bits (right click on SPDIF and select properties -> Advanced tab).
    raflevi wrote:
    when you said to install ddl? pack you mean the "[url="http://buy.soundblaster.com/_creativelabsstore/cgi-bin/pd.cgi?page=product_detail&category=Software&pid=F 2222SR6PAKH5DGY6SD">Dolby Digital Li've Pack - SB Audigy Series[/url] "?
    thanks again for all your help.
    i wanted to use the 5. function mostly for games
    Yes... also please see the link in my previous post.
    Hope this answers your questions.

  • [SOLVED]Problem with packettracer and firefox

    Hi
    I've got a problem with firefox and packettracer.
    When i click on pka file in firefox, it don't open this file in packettracer but wants to save on disk. I've got a version 5.3.1-1 packettracer and latest version firefox.
    I don't know when problem was occured but last week everything was ok. I think that's either update. Meyby it's important that when i type in console:
    update-desktop-database /usr/share/mime
    i've got such errors:
    Unknown media type in type 'all/all'
    Unknown media type in type 'all/allfiles'
    Unknown media type in type 'uri/mms'
    Unknown media type in type 'uri/mmst'
    Unknown media type in type 'uri/mmsu'
    Unknown media type in type 'uri/pnm'
    Unknown media type in type 'uri/rtspt'
    Unknown media type in type 'uri/rtspu'
    Unknown media type in type 'fonts/package'
    Unknown media type in type 'interface/x-winamp-skin'
    i have installed kde 4.5.5-1
    Do you know some solution for my problem?
    edit: update firefox solve my problem
    Last edited by ElNinijo (2013-06-08 08:35:12)

    I've had this happen now and again. You can rebind the lease yourself with:
    $ dhcpcd --rebind
    You could also try increasing the timeout by adding
    TimeoutDHCP=
    to your netctl profile/s - see netctl.profile(5) as WonderWoofy suggests. Although I haven't tried the latter.
    Last edited by youngdm (2013-09-01 22:01:05)

  • [SOLVED] Problem with zsnes and xcb_io.c on arch64

    Well after doing a pacman -Syu, zsnes won't start, when i run it, it gives me the next output
    [pablo@pablo-laptop ~]$ zsnes
    ZSNES v1.51, (c) 1997-2007, ZSNES Team
    Be sure to check http://www.zsnes.com/ for the latest version.
    ZSNES is written by the ZSNES Team (See AUTHORS.TXT)
    ZSNES comes with ABSOLUTELY NO WARRANTY. This is free software,
    and you are welcome to redistribute it under certain conditions;
    please read 'LICENSE.TXT' thoroughly before doing so.
    Use ZSNES -? for command line definitions.
    Starting Mouse detection.
    Unable to poll /dev/input/event11. Make sure you have read permissions to it.
    Unable to poll /dev/input/event10. Make sure you have read permissions to it.
    Unable to poll /dev/input/event9. Make sure you have read permissions to it.
    Unable to poll /dev/input/event8. Make sure you have read permissions to it.
    Unable to poll /dev/input/event7. Make sure you have read permissions to it.
    Unable to poll /dev/input/event6. Make sure you have read permissions to it.
    Unable to poll /dev/input/event5. Make sure you have read permissions to it.
    Unable to poll /dev/input/event4. Make sure you have read permissions to it.
    Unable to poll /dev/input/event3. Make sure you have read permissions to it.
    Unable to poll /dev/input/event2. Make sure you have read permissions to it.
    Unable to poll /dev/input/event1. Make sure you have read permissions to it.
    Unable to poll /dev/input/event0. Make sure you have read permissions to it.
    ManyMouse: 0 mice detected.
    zsnes: xcb_io.c:515: _XReply: Assertion `!dpy->xcb->reply_data' failed.
    Abortado
    it was working fine until yesterday, i've been searching about xcb_io.c but sadly i haven't found anything useful.
    Edit:
    it seems i can run it fine as sudo but not as a regular user
    Edit2:
    well it seems that there was something wrong with my .zsnes folder, i deleted it (well first i made a backup of it) and i can run zsnes again.
    Edit3:
    well, it seems i got a problem with opengl and my catalyst driver (but i'm guessing because i haven't tried with radeon) because i can use it without opengl but as soon as i change the video option to use opengl it crashes with the same error (zsnes: xcb_io.c:515: _XReply: Assertion `!dpy->xcb->reply_data' failed.) should i file a bug report or something???
    Last edited by jpablo (2011-08-30 17:12:55)

    Finally i had to edit my .htaccess file adding a RewriteBase rule to it.

  • [SOLVED] Problem with netctl and dhcpcd

    Hi everybody,
    I had a problem with netctl and dhcpcd.
    I was using netctl and wifi-menu to connect to wirelless networks with dhcp.
    It worked fine at home, then i went to a friend where it also worked but then i went back home and it failed at every try with those error messages:
    dhcpcd[2718]: version 6.0.5 starting
    dhcpcd[2718]: wlp9s0: rebinding lease of 192.168.1.154
    dhcpcd[2718]: wlp9s0: reject NAK via 192.168.178.1
    dhcpcd[2718]: wlp9s0: soliciting a DHCP lease
    dhcpcd[2718]: wlp9s0: offered 192.168.178.44 from 192.168.178.1
    dhcpcd[2718]: timed out
    network[2659]: DHCP IP lease attempt failed on interface 'wlp9s0'
    systemd[1]: netctl@wlp9s0\xxx.service: main process exited, code=exited, status=1/FAILURE
    systemd[1]: Failed to start Automatically generated profile by wifi-menu.
    systemd[1]: Unit [email protected] entered failed state.
    I figured that dhcpcd tried to rebind an ip that my router rejected and didn't accept the ip that it offered instead.
    The solution was to delete:
    /var/lib/dhcpcd/dhcpcd-wlp9s0.lease
    now how can i configure netctl and or dhcpcd so that won't happen again and that it accepts all ips offered by routers?
    Last edited by Samy (2013-09-04 13:32:13)

    I've had this happen now and again. You can rebind the lease yourself with:
    $ dhcpcd --rebind
    You could also try increasing the timeout by adding
    TimeoutDHCP=
    to your netctl profile/s - see netctl.profile(5) as WonderWoofy suggests. Although I haven't tried the latter.
    Last edited by youngdm (2013-09-01 22:01:05)

  • Problem with Frameset and page session

    All,
    I am having a problem with Framesets and page session attributes. I
    have a client who's application uses a three frame frameset. They
    have a requirement on several pages that when a button is pushed two
    different pages load into the right and left frames. The way they
    are accomplishing this is that on the pages were this is required,
    they are adding target="_top" to the form declaration in their JSP.
    Then they store the page names they want to display in session,
    forward the request to the frameset, the frameset then determines
    which pages to display based on the session variables. This works
    exactly how they want it to.
    Here is our problem. We need to store some information in page
    session attributes. We have tried to get a handle to the desired
    view bean and call the setPageSessionAttribute method. However,
    since we are forwarding to the frame and the frame handles displaying
    the desired JSP, that view bean we had the handle to is not the one
    that is created to hand the display of the JSP.
    The next thing I tried was to use the request object. In the
    handleBtnRequest method, I set an attribute in the request object. I
    then query the request object in the beginDisplay event of the view
    bean. When the frame is reset the request object does not contain
    the attribute that I have set. I'm confused by this because I
    thought the request object would be available to me throughout the
    life of the request.
    Given the above information, does anyone have any suggestions? Also,
    am I going about this in the wrong manner.
    The client had been storing this information in user session, which
    seemed to work. However, since the data being stored dealt
    specifically with data for the requested page, we felt that storing
    it as page session was more appropriate.
    Thanks,

    The script on your page web page has some obvious bugs.. Best
    fix those
    first before looking to blame Flash.
    Jeckyl

  • Tp ended with error code 0247 - addtobuffer has problems with data- and/or

    Hello Experts,
    If you give some idea, it will be greatly appreciated.
    This transported issue started coming after power outage, sap system went hard shutdown.
    Then we brought up the system. Before that , we do not have this transport issue.
    our TMS landscape is
    DEV QA-PRD
    SED-SEQSEP
    DEV is having the TMS domain controller.
    FYI:
    *At OS level, when we do scp command using root user, it is fine for any TR.
    In STMS, while adding TR in SEQ(QA system), we  are getting error like this.
    Error:
    Transport control program tp ended with error code 0247
         Message no. XT200
    Diagnosis
         An error occurred when executing a tp command.
           Command:        ADDTOBUFFER SEDK906339 SEQ client010 pf=/us
           Return code:    0247
           Error text:     addtobuffer has problems with data- and/or
           Request:        SEDK906339
    System Response
         The function terminates.
    Procedure
         Correct the error and execute the command again if necessary.
    This is tp version 372.04.71 (release 700, unicode enabled)
    Addtobuffer failed for SEDK906339.
      Neither datafile nor cofile exist (cofile may also be corrupted).
    standard output from tp and from tools called by tp:
    tp returncode summary:
    TOOLS: Highest return code of single steps was: 0
    ERRORS: Highest tp internal error was: 0247

    when we do scp using sm69,
    SEDADM@DEVSYS:/usr/sap/trans/cofiles/K906339.SED SEQADM@QASYS:/usr/sap/trans/cofiles/.
    it throws the error like below,
    Host key verification failed.
                                                                                    External program terminated with exit code 1
    Thanks
    Praba

  • Problems with notes and mark ups in pdf

    I'm having problems with the Adobe reader for iPad.
    Whenever I modify a pdf file, adding notes or any other mark up, I'm not able to see any of the markups in the file when I open the same file with another application or I send it via e-mail.
    Only the digital signature is still visible.
    Thanks

    You are correct. When i open it with Adobe i get my mark ups etc. When i use Apple`s pdf view i do not.
    Problem solved.
    Date: Mon, 17 Dec 2012 10:46:22 -0700
    From: [email protected]
    To: [email protected]
    Subject: Problems with notes and mark ups in pdf
    Re: Problems with notes and mark ups in pdf created by Pat Wibbeler in Adobe Reader for iOS - View the full discussion
    Can you share what applications you are using to view the notes after emailing? You have to view the document in a Reader that supports annotations. Apple ships a built in pdf viewer (like the one used in iBooks) that many iOS developers use (e.g. Dropbox, email). This built in PDF viewer does not support rendering annotations. However, many other applications (like the Adobe Reader for iOS and the Adobe desktop products) do support Annotation rendering. Similarly, one of our competitor's PDF viewers (PDFExpert) supports this functionality as well. Annotations are part of the PDF standard and the specification is widely available and we would love to see more renderers support it!
    Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/4927598#4927598
    Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4927598#4927598
    To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4927598#4927598. In the Actions box on the right, click the Stop Email Notifications link.
    Start a new discussion in Adobe Reader for iOS by email or at Adobe Community
    For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • Problems With Syncing and Audio Play with Itunes

    I've been having a problem with Itunes and my iPhone for the past few days. First of all, iTunes will not play any songs. When I press the play button, the speaker changes to the play picture, and the song loads at the top, but the timer stays stuck on zero. Also, when I attempt to sync my iPhone it will not add new songs downloaded onto my phone. I have updated and re-installed iTunes and it has not helped. Also, tonight I even updated my phone settings (which I interestingly enough was able to do despite the fact that I cant get a song to transfer to my iPhone, yet somehow the new program settings were able to make the jump.)
    I am using Windows Vista at the moment. Does anyone have any idea as to what could be going on? Any help would be greatly appreciated.

    Hi,
    Have you tried backing up you iPhone and copying over everything to iTunes etc.Apps,Videos...Then Restoring to factory setting?
    If that doesn't work try Manually Managing you Music and Videos.

Maybe you are looking for

  • HT1689 how can i get a list of purchases, like for in app purchases?

    i have had issues with an app, and was asked to submit receipts for what I had bought. My app crashed with an update and beeline said they would credit my account if I had receipts. I did not save every receipt apple gave to me. Is there a way to vei

  • Connecting a 2007 external monitor to a 2001 ibook

    My new external monitor has a DVI connector and my ibook has a mini-vga port. I ordered a mini-VGA to standard-VGA cable from Apple and I ordered a DVI-to-VGA cable from Apple. However, the DVI connector has a male configuration and the monitor has a

  • Document creator cannot add adhoc approver in shop-in one screen

    Hi All, We are working with SRM 7.0, SP11 with extended classic implementation. We have observed that while creating a SC with professional view (shop-in-one screen) with purchaser role, user cannot use adhoc approval function as the Button 'Add Appr

  • Creating a vendor

    Hello, I have a question asked by the purchasing department. When they create a new vendor, could the Goods-receipt-based inv.verif. check and the currency come automatically? as if saved as a variant? If the currency is different, then they'd change

  • Windows server 2008 R2 Enterprise Service Pack 1 - TCP/IP Registry settings

    I am facing the issue  while making TCP/IP connections. This issue is occuring sometimes and not usual. No connection could be made because the target machine actively refused it 127.0.0.1:8056. This issue is due to server has full backlog. Questions