Problem with bios K7N2 delta - L

i come frome poland and i have a problem
i have msi k7n2 delta - L ,athlon 2600XP,ddr 400/512,msi ti 4200x8
i have bios in my computer version 5.20 and when i upgrade to version 5.30 , 5.40 and 5.50 5.60 when i play in games or when run 3dmar 2001 system failed.
in version 5.20 temperature cpu is false and i have upgrade to new version bios
but i cant please help me.

Something worth trying is clearing the bios via the jumper next to the battery then set your preferred settings inthe bios. It dont say that in the flash instructions but something i always do.

Similar Messages

  • Problems with MSI K7N2 DELTA ILSR

    I set my bios to high performance defaults and now when i turn it on the diagnosis LED's say that the processor, then the RAM are damaged, but this isnt the case as i have tested them in a different machine and they are ok. I have tried clearing the CMOS using the jumpers but nothing happens. I have read on here that the way to solve this problem is to set the CPU FSB jumper to 100mhz... could somebody please tell me if there are any other usjestions about how to solve this please...
    Nick

    Quote
    Originally posted by Nerdyjim
    cheers.. is it worth going for a 3200+ Athlon, or should i save the money and go for a 3000+ Athlon??
    Get something like a 2700+, I've got one, if I OC the FSB by 5, I achieve the performance of a 3200+, I can go higher, but I don't want to until I get a volcano 12, soon.

  • Cpu problems with my k7n2 delta

    last week i thought that my motherboard was defective, but help from these forums said that it was my memory. Now that i have 2 sticks of corsair xms3200 256mb ddr 400mhz I actually got winxp to install.  With the old memory I would just get errors while installing XP.  But my problem now is that right after I installed XP everythign ran fast and smooth, but after a couple of installations of programs/drivers the comp starts to get sluggish.  When i press ctrl+alt+del i look at the cpu usage and it usually sitting at 100%/99/98 around that area. What is wrong with my computer now. I am having so many problems, i'm stuck using a 600mhz amd.
    xp1800+
    2 x 256corsair xms3200
    abit siluro 4200 128mb 8x agp
    WD 8mb cache 60gig
    sb audigy2
    netgear lan card
    52x24x52 verbatim burner
    antec 350wtts

    Oh and also during the Windows xp professional boot up screen where there is a blue bar that goes from left to right at a moderate  speed.  It will do that for a couple of seconds and then pause, the move, then pause, continue for a minute or two, then go back to that moderate speed.  So it seems like it is being slowed down during boot up.

  • MOVED: need help with my k7n2 delta series motherboard please

    This topic has been moved to AMD SocketA based board.
    need help with my k7n2 delta series motherboard please

    "...the other memory ive been using is  memorymaxx 512mb ddr 3200..." If I understood right, your'e actually using both memories at same time so, your'e lucky if it works. We have said thousand times that mixing dif. brand/make/speed memories is a bad idea, most with this Mobo that is very picky about ram. If you want to avoid slowdown problems, stay with only one stick ( the better one ) until you can buy at same time in same store, 2 identical memories to replace the old one.

  • XFX GeForce 7600GS 512mb AGP with MSI K7N2 Delta Problem

    Hi, I have been searching in everyplace and still I havent find a solution.
    I have the XFX GeForce 7600GS 512mb AGP card.
    I use the MSI K7N2 Delta.
    My Processor its the AMD 2600+ XP
    my PSU its a 420watt
    my RAM its 2gb DDR 400
    I made everything in the bios, didnt work.
    I updated the lastest drivers and bios, didnt work.
    I went to a friend house, he use a P4 motherboard with 500watts. Worked, PERFECTLY.
    I changed the card once (the first one didnt worked at all) but this one worked...
    now the question is:
    HOW I MAKE IT WORK IN MY PC  ?????????
    Can anyone help me?  I dont wanna sell it to a friend for only 60$ (that the only costumer I have found for the card in Panama)

    Heh I had problems with trying to see again was what happening in my PC but yesterday....
    Ok I went to my friend house, we used the card with his 350 watts 15A in the 12V+ and it worked.
    Then we tried to install the PSU but I dont know why its 4pin was incompatible with mine....
    Well heres the important part: I went to a local Computer Store where they repair too and with another more powerfull PSU in my PC  and the card didnt worked for seconds, but the guy played a little with my Ram and he noticed that its posible to that be the problem. Remember that my ram its a Kingston 400DDR 2X1 Gb running in the purple and the green slots of the mobo. when we changed them to both purples slots of the mobo the PC dosent work and make a the beep sound. I have the braket in my computer and it showed a red dot here:  GR
                                                                                                                                                                                                               GG
    Gonna search the manual to know what that means.

  • MOVED: XFX GeForce 7600GS 512mb AGP with MSI K7N2 Delta Problem

    This topic has been moved to Retired motherboards.
    https://forum-en.msi.com/index.php?topic=124849.0

    Heh I had problems with trying to see again was what happening in my PC but yesterday....
    Ok I went to my friend house, we used the card with his 350 watts 15A in the 12V+ and it worked.
    Then we tried to install the PSU but I dont know why its 4pin was incompatible with mine....
    Well heres the important part: I went to a local Computer Store where they repair too and with another more powerfull PSU in my PC  and the card didnt worked for seconds, but the guy played a little with my Ram and he noticed that its posible to that be the problem. Remember that my ram its a Kingston 400DDR 2X1 Gb running in the purple and the green slots of the mobo. when we changed them to both purples slots of the mobo the PC dosent work and make a the beep sound. I have the braket in my computer and it showed a red dot here:  GR
                                                                                                                                                                                                               GG
    Gonna search the manual to know what that means.

  • HELP me with my K7N2 delta ilsr

    Can anyone help me with this problem. I have just upgraded to MSI's K7N2 delta ilsr motherboard. Its all working quite well apart from the fact that the pc wont start up from cold....at all.
    When I start the pc from an off state, it runs up the fans and drives, but does not post.
    The diagnostic led pannel on the back of the pc shows that the cpu is faulty or not installed correctly.
    If I then press the reset button, the pc posts, and boots up just fine.
    It does this EVERY time I start up.
    I have tried re installing the cpu, which is an XP 2800+ 333 barton, but to no avail.
    I have asked a few questions on other forums, but I cant solve it.
    These are the suggestions so far.
    1. the psu (I have a Tsunami 400 atx psu) could not be giving out enough power on initial startup, but once the pc is running, it has enough to boot the pc from a reset.
    2. The mobo or the bios could be at fault. I have not flashed the bios, or upgraded it in any way from original, so is there an issue with the original bios on these boards, and 2800 barton chips??? Could it be a mobo fault? The pc runs fine once the machine is booted.? how do I test it?
    3. The cpu could be faulty? but would this not stop it running fuull stop?
    4. my ram. I have a single stick of OCZ 512mb pc3200 ddr, which I was told would make the pc fly. Not shure on that statement, but is this ram compatible?? could this be the problem?
    Im fairly new to the upgrade side of things, and I need some help with this one.
    Also, Id be really greatfull if some one could talk me through flashing my bios to the latest version, as the thought of doing this narks me a bit...I dont want to mess it up and get a dead pc...
    HELP

    +3.3v 14A
    +5v 28A
    +12v 16A
    +5vsb 2A
    -5v 0.5A
    -12v 0.8A
    Hope this helps, as my pc seems to be living with its case off a lot these days..haha

  • Internet Connection Problem on MSI K7N2-Delta-ILSR

    Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
    Athlon XP 2400+ Overclocked to 2205MHz
    2 memory modules of 256MB 400 manufactured by Samsung
    TharmalTake Volcano 11
    Triplex Xabre 400 PRO with 128MB
    Hercules Gamesurrround Fortissimo III 7.1
    Microcom InPorte Home modem 56k
    Leadtek winfast 2000 (TV/FM radio)
    Acard SCSI controller (Acard AEC-6710D) for my scanner
    WesternDigital WD800 GB
    WesternDigital  15.3gb
    Bios ver.7.4  
    Can anyone help me?

    Quote
    Originally posted by Roger Wilco
    Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
    I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
    I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
    I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
    Anyone else in the same boat?
    Hi,
        Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck  
    Rob

  • TROUBLE with the K7N2-DELTA

    I just purchased and set up a K7N2-DELTA. I am having a problem. I cant get to the bios... all I see is the slpash screen with the 8x graphic.
    My D-Bracket shows three green and one red and unless the manual is wrong it means that the floppy is being initialized.
    I have tried switch the cable around ever which way, clearing the CMOS and restarting, tried three different floppy drives, two different cables but all I get is a fancy 8x graphic and a red light. I have tried to boot nothing but a video card (GeForce MX440 8x 128mb), one stick of ram (512 kingston pc266), HD (WD) and a CD drive (took off the floppy) and it still isn't working.
    I will try any suggestion besides throwing the MB out the window :o).
    HELP PLEASE!!!!!!
    I have also tried pushing DEL before the graphic appears and then the D-Bracket says initializing the memory. I even switch between 1 and 2 using 1&2, 1&3, 1&2, just 1 and just 2.
    I cant believe that I bought this new board and I cant even get to my BIOS... any and all help would be appreciated. X(

    Your right the D Bracket is not correct and has actually hurt instead of helped me troubleshoot.
    After more trouble shooting I think it is my HD that is at fault here. Maybe someone can relate to this and or has a solution.
     I have the following set up
    IDE 1
    Master- 40gb HD (which I will refer to as HD1) (which is the one I'm having problems with)
    Slave- 40gb HD (which I will refer to as HD2)
    IDE 2
    Master- CDRW
    Slave- DVD
    I'm having some real issues with this. Again my system wont go past the slash screen before bios. I can get past this problem by doing the following.
    On IDE1 put CD drive as master and set HD1 as Slave. It will boot to bios but the bios wont read the HD1 and it says the CD is IDE1 Slave. I dont understand this because the jumpers are set as master and it is the first on the IDE cable.
    I have hooked HD1 to another system and ran WD diag floppy and erased the entire thing and tested and it says no errors are found.
     Move the drive to the MSI board and I'm stuck at the splash.
     I have tried moving jumpers to CS and SLAVE and standalone but no changes.
    HD2 is my old C drive so I dont want to try this as MASTER and re-install XP or I will loose data.
    Hopefully this will find someone who has experiance the same or similar problems and have some advice for me.
    One more thing.. on a seperate comuter HD1 reads as a drive in XP and works fine... just cant get to to work on the new board.
    ANY SUGGESTIONS????

  • Someone plz help me with my k7n2 delta-ilsr

    Hey everyone,
            I just put my sytem togother and ran into a problem.  I got the system to boot up just fine.  It was not until I tried installing windows xp proffesional that  I ran into problems.  The installation process runs pretty smoothly, until the computer reboots to run windows for the first time.  After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer.  I have never encountered this problem before when I built other systems.  The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly.  The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process.  Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message.  I am stumped anybody have any ideas of what I might be doing wrong?  Any help would be appreciated .  My system specs are below.
    MSI k7n2 delta-ilsr mobo
    AMD 3000+ Athlon XP cpu (333 fsb)
    ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
    x1 kingston 512mb pc3200 DIMM
    x2 maxtor 80gb maxtor hdd's
    x1 regular cd-rom drive
    x1 floppy drive
    420w raidmax psu
    (+3.3v = 26A, +5v = 32A, +12v=13A)

    Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
    Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
    The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
    The timing you show probly should be something  like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
    The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
    Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

  • HD or Booting problem on MSI K7N2 Delta 2 Platinum

    Hi all,
    Ive a weird issue which i cant figure out myself. I've 2 HD's..lets call them A and B where A = 60Gb (Master) and B = 80Gb (Slave)
    It's is like this:
    A and B are connected to the primary IDE-slot. A will boot when set as Master and B wont start booting when set as Slave mode (i mean, it wont show/appear in the first hardware (detection) bootscreen of yer BIOS where it says its present or the so called POST-screen), but if I set B as Master only (A turned off) it will boot.
    What also happens is if I disconnect the power of drive B..drive A will boot..and while OS is loaded...I turn on the powercable from drive B and reboot..suddenly out of the blue it detects both HD's and reboots like it should do normally...but when i reboot from than..the same thing happens again..(it wont recognize B anymore)
    Sumtime it regonizes both drives and sumtime it just won't and sumtimes just 1 drive..
    Another thing, when it won't recognize one or sumtime both drives...the POST-screen gets stuck at the name and version of the BIOS...and where it says: 'detecting IDE drives...'  when it is at this stage..and I press  on the DEL-key for example..it's loading damn too slow..I've to wait about 10min before it enters the BIOS-setup..
    I am 100% sure I set the jumper correctly for Master or Slave mode on my HD..I know there's sumthing wrong..but don't know where...Ive changed the jumper with a new one  ..switched IDE-cables...switched HD's (set B as Master and A as Slave and vice versa, knowing there is no active partition on B..but only to check if it recognizes the drive)..in all cases..the BIOS settings are set as default!
    any1 can help me out with this?
    It worked smoothly on my system till i noticed my second MEM bank of my mobo broke (Asus A7N8X-E)..so i had to change it quickly (and went to the store with my warranty to fix this board..it was only 3 months old) ..since I've seen/had enough Asus mobo's in my life I went this time for an MSI which looks better in my opinion...so now i have an MSI K7N2 Delta 2 Platinum..it works fine...except that HD issue mentioned above
    any help would be appreciated..thnx in advance!
    cheers!

    Hi,
    I've done that already several times...it doesnt work..any other suggestions?
    Now I can boot normally when I disconnect the power of the 2nd HD (or just any HD)...when the os is loaded...I turn back on the power of the 2nd drive and reboot...than it will run/boot/restart etc..normally...this is the only workaround I have at the moment...this only works when the system is turned a long time...
    My power supply is 400W..so I don't think Ive any prob with that
    cheers

  • 870A-G54 problems with bios, ram and CnQ

    Hello i have some weird problems with my mobo.  CnQ dont work i dont know why , in bios all options are turned not automaticly but forced to be "enable" ,and still my procesor multipler and voltages don't change , at the beginning after installing win7 64x it worked but now no :/.
    2.next i have problems with memory i have corsair xms3 2x2gb [email protected]  at old bios(AH0) my memory just did'nt want to work on 1.6k in dual channel and 1,2 slot i tried even to use default voltages tested by corsair (1.65V i had to use 1.66) result it dont work. after putting them into 3,4 slot it works even on 1.5V not 1.65V then i used to have them on 3,4 slot      do u think that 1,2 slot is damaged ?.
    3.Problems by bios. I updated my bios to the lastest version (from software downloaded from msi.com  probably it had name "live update 5") , of course updated by usb stick .Then after update i see that my ram looks like reserved bios showing me that i have 2gigs of ram -.- (but only on 3,4 slot x.x) after change slots (1,2) it working and see my full ram (4gigs). Is that HD0 beta version of bios ? it looks like that .I don't see my logo screen it looks like that option was cut off from the bios , i don't see any "corporation" logo while booting the system.
    I though that msi making solid motherboards as u can see i have many problems with this mobo.
    Help me and thanks for all post (which wanna help me :D)

    CPU brand, AMD PHENOM II X4 955BE C3
    Motherboard model  870A-G54 REV 3.0  
    Memory Corsair xms3 2x2gb cl9 1.6kMHz
    Nvidia Geforce gts450 oc1 1gb gddr5 gf106
    Hard drive(s) samsung 250gb sata 2 80mb/sec
    Windows 7 home premium 64bit
    Delta dps-700MB A  700W           (12v1 17A0  (12v2 18A) (12v3 17A)  (12v4 17A) (+5v 25A) max for 12V= 50A (+3.3 20A)  (-12 0.6A)  +5V and +3.3 max 160W  MAX output 700W

  • Got a problem with BIOS in my board MSI 785GM-E51

    i have a MSI 785GM-E51 board,i got a problem with the graphic card bus interface,it still run in 8x not in 16x
    i try to disable a onboard graphic on BIOS,but i not find it.
    and last i try to update BIOS to v2.4 n' not work too.
    this a example;

    Quote from: Bas on 08-March-10, 21:21:36
    You do not need to disable the onboard.
    As for the plug-in card, there is nothing in the BIOS to make it work 8x or 16x.
    Make sure your card is seated correctly, else it will work but at lower number of lanes.
    What program is telling you it's 8x?
    GPU-Z

  • G4Ti4200-VTD64 voltage incompatibility with MSI K7N2 Delta-ILSR??

    Hello,
        I have the MSI G4Ti4200-VTD64 (4X) video card..  I want to upgrade my motherboard to K7N2 Delta-ILSR. Is there any voltage incompatibility?? I heard that new mother boards will support only AGP 1.5V. Is the AGP voltage of K7N2 Delta-ILSR 1.5volts??  Is my video card compatible with this voltage?? I really want to retain my current video card as I am quite satisfied with it and I'm not willing to invest on a new one at the moment. If there is an incompatibility could you suggest another Socket A MB with good performance and SATA RAID support.
    Thanks in advance
    Regards,
    Joseph

    Joseph,
    All 4X Vid Cards work on all 4X and 8X mobos. All 4X mobos work with all 4X and 8X Vid Cards.
    Take Care,
    Richard

  • Kt4v possible problem with bios 1.8 and hd

    Any Idea anyone with this one.
    system running well till the other day when hd went very slow even after defrag, install bios 1.8 and reset the bios and adjusting it for my setup. Come to check my harddrive with maxtor powerdiag 3.04 and could not find the drive or any other drives connected. In the bios setup the drive is present. I removed all drives, cdroms, etc except the maxtor main hd and tried again with the same result. After placing in an ata100 controller card in to a spare pci slot and plugged the hd on to it, that the software sees the drive. The test finished and show the HD to be fine.
    The question is do I have a problem with the onboard contoller or with the new bios or both.
    When I first got this MB I did the same test with the original bios and the hd connected to the MB controller and the software had no problem seeing that and other drive connected.
    my pc  
    6712 mb kt4v
    athlon 2700+
    ti4200 graphics card
    2 off ddr333 512Mb memory
    floppy drive
    sony cdrw
    system software windows xp pro
    hard drive maxtor d740x-6l 60Gb ata133

    I'll stick with the V1.10, but I'd fell better if MSI showed me they actively update their systems by releasing updated BIOS files from time to time.
    I can't sell a 15000$ storage system that doesn't recognise the CPUs installed. The customer would laugh and tell me to come back with a supported system.
    Isn't this a VERY valid reason for wanting updates? Even if it only is an updated CPU list?
    The only reason I tried this MSI board is that it was the only one available with my retailer at the time I bought it with 3 PCI-X 100Mhz slots. Maybe I should go with a Tyan Thunder next time. Tyan at least show some activity.

Maybe you are looking for