Problem with Cisco 1240AG Access Points
I have a Cisco 1240AG Access point (P/N ? AIR-LAP1242AG-A-K9).
It has come in the lightweight mode.
I just want to know whether I can put it to the autonomous mode.
Hi Indika,
Here is a conversion method (look most of the way down the attached doc);
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob
Similar Messages
-
PoE auto switchover with Cisco 1252 Access Point.
Dear All
I have a network for Managed Wireless using Cisco. This is a new network for me.
I am in problem with Cisco Access Point 1252. My AP's are connected to a PoE Switch. And Cisco AP's are also connected Powered with also Power Adapter with UPS backup.
But problem is if I disconnect power source of AP Power Adapter , AP is not getting up with PoE. PoE is up only when POWER PLUG of AP ADAPTER is physically pulled out from Socket.
Question is if it is possible to make automatic Failover by PoE when Power source of AP ADAPTER is down ?? I mean no need to PULL OUT POWER PLUG of AP ADAPTER.
Waiting for your rely.
It is very urgent .
Thanking You
Subrun.Hi Suburn,
1- yes it is possible to do failover without unlupping the cable of AC adapter. When power on ACS adapter is off, then the faiolver happens.
2- with regards to POE, if your switch supporting enhanced POE?
Powering the Aironet 1250 Series Access Point with Cisco Enhanced PoE
Cisco Enhanced PoE was designed for customers who want to install new PoE-enabled technologies that require greater than 15.4W per port to function at full capability, such as wireless technology based on the IEEE 802.11n standard. Cisco Enhanced PoE provides the full power requirements for dual-radio modules and eliminates the need to run an additional cabling drop or insert a separate power injector. Support for Enhanced PoE is currently available on a variety of Cisco Catalyst® switching platforms. For more information on Enhanced PoE, visit http://www.cisco.com/en/US/prod/switches/epoe.html.
Serge -
Mac mini not keeping connection with Cisco wireless access point
I am trying to get my wife's Mac Mini to keep it's connection with the wireless network at her school. They are using a Cisco access point (not sure of the model) which works fine with my G4 Powerbook and the numerous Macbooks being used there, but for some reason her Mac Mini drops the connection after 4 or 5 minutes, at which point she needs to log right off for it to reconnect (as opposed to just turning the card off and on again). I have already gone through the deletion of the Networkinterfaces.plist file, and recreation of the Airport card profile process, but this only kept the interface active for about 36 hours, then it was back to the same old problem. At this point I am thinking "flakey card"...before I ship it off to Apple, can anyone offer any other possible solutions?
After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!
-
IPhone will not sync with Cisco Wireless Access Point
This is unbelievable, i just bought a $1000 phone and it wont sync with a Cisco AP. I can sync it with a DLINK? I there a specific list of Access Points it will connect to. If so thats complete bullsh*(. Also, is there going to be a firmware update soon to fix these problems. Can you tell that im a little upset. I just saying that if someone spends $1000 dollars on a phone it should be working pretty dam good. Anyway can someone offer any suggestions?
Upset Iphone user.After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!
-
Problem with Cisco Secure Access Server 3.0
Hi All,
Please what is my problem? I use Cisco Secure Access Server Version 3.0 for Windows 2000/NT Servers to authenticate users on our wireless network. I however wish to assign monthly time limits to each user after which he/she will no longer have access until next month or the timer is reset. I tried this with the "User Usage Quota" under User setup. I set the Server to "Limit user to X hours of online time per Month" and enabled the "Use these settings" and also checked the box by the side of the option. I saved and restarted my server. Unfortunetly the settings did not work for all the users whose quotas I set.
What Am I doing wrong. Please assist.
ChafeDo you have your AP's sending accounting data? If not, ACS has no way of knowing how long they've been online?
You can utilize your ACS logging to see what your accounting looks like to confirm whether you are receiving accounting packets or not?
HTH
Jeff -
I own a Cisco Wap300 access point . there are a pc, a netbook and a smartphone in my house. I want to connect to these devices my line of fiber internet with Cisco Wap300 access point. My modem brand and model is "ZTE - Zxhn H168N". This modem has 300 Mbps wireless connection speed. Which settings of access point should I use to work my all devices .
I'am using Air 2310 wireless adaptor for Pc
I have a netbook and HTC wildfire S smartphoneAre you referring to this?:
http://www.cisco.com/cisco/web/solutions/small_business/products/wireless/300_series_wireless_access...
or this?:
http://support.linksys.com/en-apac/support/accesspoints/WAP300N
It's good if we identify the device first before we get the ball rolling. -
Any new firmware for the Cisco AP541N access points.
Do you know if Cisco has come out with any new firmware for the Cisco AP541N access points.
Latest release is 1.8.0 from Jan 25, 2010:
http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=1.8.0&mdfid=282790482&sftType=Small+Business+Pro+Wireless+Software&optPlat=&nodecount=2&edesignator=null&modelName=Cisco+AP+541N+Wireless+Access+Point&treeMdfId=278875243&treeName=Wireless&modifmdfid=null&imname=&hybrid=null&imst=null&lr=Y -
CISCO Aironet access point - not able to connect by user.
Hi,
I have CISCO Aironet access point C1130 in my network , but not able to connect by users, I can see below logs from access point. please help on this.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:20.544: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:20.544: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:24.832: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:24.832: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:29.741: RADIUS: Fail-over denied to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS: No response from (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS/DECODE: No response from radius-server; parse response; FAIL
Jun 13 17:50:29.741: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
Jun 13 17:50:29.741: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAILOVER_RETRY
Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
Jun 13 17:50:29.742: Client 5864.6c67.3718 failed: EAP reason 0
Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: Failed client 5894.6b37.3518 with aaa_req_status_detail 0
Jun 13 17:50:29.742: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for 5894.6b37.3518
Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client 5894.6b37.3518
Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
Jun 13 17:50:29.743: dot11_auth_dot1x_send_client_fail: Authentication failed for 5894.6b37.3518
Jun 13 17:50:29.743: %DOT11-7-AUTH_FAILED: Station 5894.6b37.3518 Authentication failed
Regards,Hi Niham,
You can try few things to troubleshoot this -
1. check the reachability of Radius server from your wlc (ping).
2. verify the IP address of Raduis server configured on wlc.
3. wlc in the Radius server ?
4. Shared Secret must be same on wlc and in raduis server.
Plz do not forget to rate useful post.
Thanks -
Cisco 1230 access point a radio lightweight mode
Will the cisco 1230 access point work in lighweight mode if it is using a radio?
The 1230 can be upgraded to LWAPP with the A Radio model listed below;
Solution Requirements
Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
All 1130AG access points
All 1240 AG access points
For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and **1230 AP**) platforms, it depends on the radio:
if 802.11G, MP21G and MP31G are supported
if 802.11A, RM21A and RM22A are supported
The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
All 1310 AG access points
From this good doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
Hope this helps!
Rob -
Cisco 2602 Access Point - Support
Dear Team,
Could you please advise, if Cisco 2602 Access Point supports IPS and CleanAir along with Access Point feature or does it need to work as standalone to have these functions enabled ?
Regards,
SIDMight as well add my 2¢
In order to have CleanAir, you need a WLC. In order to do IPS, wireless its called wIPS, you need an MSE and NCS or Prime Infrastructure.
A standalone access point (autonomous) is just a dumb AP and can't perform any of those functions:)
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
I have a tesco router and an external hard drive attached to it as a network drive (shared) for my macbook and MB-Air. Have no problems with my MB accessing it, but with MB-AIR it says - 'the version of the server you are trying to connect to is not supported. pls contact your system administrator to resolve the problem'. MB-Air uses maverick downloaded yesterday - upgrade from mountain lion. MB uses snow leopard still, as i am quite used to it and am thinking of upgrade if mavericks work fine on air. Also have parallel on snow leopard but it is no longer supported according to mac website - if i upgrade am i going to lose my parallel and will have to buy a new one!!!
Yes, the Old Master file has a folder for each year where I find all photos from that specific year. I am attaching a screen shot of the file.
In the meantime i have managed to download all photos (it did not download any video files though in mpg, avi, 3gp, m4v,mp4 and mov format) to a new iphoto library. Unfortunately the photos are quite mixed and often doubled up. I ma considering to purchase iphoto library which checks all duplicates in iphoto. this will save me a lot of time. What do you think? -
I have a problem with ( AppleSyncNotifier.exe - Entry Point Not Found ) The procedure entry point sqlite3_wal_checkpoint could not be locate in the dynamic link library SWLite3.dll.
With Windows Explorer, navigate to your C:\Program Files\Common Files\Apple\Apple Application Support folder.
Copy the SQLite3.dll that you should find there, navigate to the nearby Mobile Device Support folder, and Paste it in there also.
Reboot and see if all is well
In case that your OS is Windows 7 (64 bit)
1. Open windows explorer, go to location C:\Program Files (x86)\Common Files\Apple\Apple Application Support
2. Copy file "SQLite3.dll"
3. Open new windows explorer, to to location C:\Program Files (x86)\Common Files\Apple\Mobile Device Support
4. Paste file "SQLite3.dll" to the location.
5. Reboot your computer, it should not display that message, it should be clear.
Good Luck -
A problem with a session Access
Hi Olivier,
To connect with Forte while running distributed you must use System DNS
instead of User DNS on the server. The ftexec.exe on your server partition
will be launched by the NodeMgr running as UID SYSTEM. User DNS are not
available to processes running as UID SYSTEM.
Zenon Adamek
Purolator
-----Original Message-----
From: Olivier Andrieux [SMTP:oandrieuxaxialog.fr]
Sent: Tuesday, July 04, 2000 4:59 AM
To: forte-userslists.xpedior.com
Subject: (forte-users) A problem with a session Access
Hi,
We have defined a service object which calls a database Access, when we
use the driver odbc of another station the service object is created and
the application runs. But when we use the driver of the server we have an
exception and this message :
SYSTEM ERROR: Unable to start the partition AxiGecom_CL0_Part1 on any of
the
nodes to which it has been assigned. See the remainder of the error
stack for
more information.
Class: qqsp_ResourceException
Error #: [1602, 593]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 5
Last TOOL statement: method InterfaceManager.PrepareLOM
Error Time: Tue Jul 04 10:50:19
Exception occurred (locally) on partition "Forte_cl0_Client",
(partitionId
= EB3ED870-274C-11D4-8051-304F7116AA77:0x3f9:0x2, taskId =
[EB3ED870-274C-11D4-8051-304F7116AA77:0x3f9:0x2.15]) in application
"FTLaunch_cl0", pid 149 on node STAT10 in environment axialog.
SYSTEM ERROR: Unable to start partition AxiGecom_CL0_Part1 on node
SERVEUR59B.
Class: qqsp_ErrorDescriptor
Error #: [1602, 592]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 3
Error Time: Tue Jul 04 10:50:19
Exception occurred (locally) on partition "Forte_cl0_Client",
(partitionId
= EB3ED870-274C-11D4-8051-304F7116AA77:0x3f9:0x2, taskId =
[EB3ED870-274C-11D4-8051-304F7116AA77:0x3f9:0x2.15]) in application
"FTLaunch_cl0", pid 149 on node STAT10 in environment axialog.
SYSTEM ERROR: Attempt to load partition named AxiGecom_CL0_Part1 failed.
Class: qqsp_ResourceException
Error #: [1001, 4]
Detected at: qqrt_ForteExecAgent::LoadPartition at 1
Error Time: Tue Jul 04 10:49:15
Distributed method called: qqrt_ForteExecAgentProxy.LoadPartition!6
(object name Unnamed) from partition "Forte_cl0_Client",
(partitionId =
EB3ED870-274C-11D4-8051-304F7116AA77:0x3f9:0x2, taskId =
[EB3ED870-274C-11D4-8051-304F7116AA77:0x3f9.4]) in application
"FTLaunch_cl0", pid 149 on node STAT10 in environment axialog
Exception occurred (remotely) on partition "Forte_Executor",
(partitionId
= EB3ED870-274C-11D4-8051-304F7116AA77:0x3de, taskId =
[EB3ED870-274C-11D4-8051-304F7116AA77:0x3de.61]) in application
"AxiGecom_cl0", pid 386 on node SERVEUR59B in environment axialog.
SYSTEM ERROR: Failed to create service object
Axigecom_Serveur.Connection_BD.
Class: qqsp_ResourceException
Last TOOL statement: method qqsp_NameList.
Error Time: Tue Jul 04 10:49:15
Exception occurred (remotely) on partition "Forte_Executor",
(partitionId
= EB3ED870-274C-11D4-8051-304F7116AA77:0x3de, taskId =
[EB3ED870-274C-11D4-8051-304F7116AA77:0x3de.61]) in application
"AxiGecom_cl0", pid 386 on node SERVEUR59B in environment axialog.
USER ERROR: (This error was converted)
Failed to connect to database: Axigecom, username: Administrateur.
[Microsoft][Gestionnaire de pilotes ODBC] Source de données non
trouvée et
nom
de pilote non spécifié
Class: qqdb_RemoteAccessException with ReasonCode:
DB_ER_DBMSCONNECTION
DBMS SQLSTATE: IM002
Class: qqsp_ErrorDescriptor
Detected at: qqdb_OdbcVendorInfo::DoSQLConnect at 10
Last TOOL statement: method qqsp_NameList.
Error Time: Tue Jul 04 10:49:15
Exception occurred (remotely) on partition "Forte_Executor",
(partitionId
= EB3ED870-274C-11D4-8051-304F7116AA77:0x3de, taskId =
[EB3ED870-274C-11D4-8051-304F7116AA77:0x3de.61]) in application
"AxiGecom_cl0", pid 386 on node SERVEUR59B in environment axialog.
for information, we use a server NT and the stations use Nt, the drivers
DNS users are declared.
We use Access2000, and the version M for Forté
Thanks in advance,
Olivier Andrieux
AXIALOG
France -
NTP Service on Domain Controller have problem with cisco switch
Hello!
I have Windows Server 2008 R2 SP1 Domain Controller with NTP services
The windows opertion system clients get NTP time ok.
There are problem with cisco switch, can't get time from NTP.
Can anybody help me to fix problem?
C:\Users\Sysuser>w32tm /query /configuration
[Configuration]
EventLogFlags: 2 (Local)
AnnounceFlags: 5 (Local)
TimeJumpAuditOffset: 28800 (Local)
MinPollInterval: 6 (Local)
MaxPollInterval: 10 (Local)
MaxNegPhaseCorrection: 1800 (Local)
MaxPosPhaseCorrection: 1800 (Local)
MaxAllowedPhaseOffset: 300 (Local)
FrequencyCorrectRate: 4 (Local)
PollAdjustFactor: 5 (Local)
LargePhaseOffset: 50000000 (Local)
SpikeWatchPeriod: 900 (Local)
LocalClockDispersion: 10 (Local)
HoldPeriod: 5 (Local)
PhaseCorrectRate: 7 (Local)
UpdateInterval: 100 (Local)
[TimeProviders]
NtpClient (Local)
DllName: C:\Windows\system32\w32time.dll (Local)
Enabled: 1 (Local)
InputProvider: 1 (Local)
AllowNonstandardModeCombinations: 1 (Local)
ResolvePeerBackoffMinutes: 15 (Policy)
ResolvePeerBackoffMaxTimes: 7 (Policy)
CompatibilityFlags: 2147483648 (Local)
EventLogFlags: 0 (Policy)
LargeSampleSkew: 3 (Local)
SpecialPollInterval: 3600 (Policy)
Type: NTP (Policy)
NtpServer: 10.7.0.4 (Policy)
NtpServer (Local)
DllName: C:\Windows\system32\w32time.dll (Local)
Enabled: 1 (Local)
InputProvider: 0 (Local)
AllowNonstandardModeCombinations: 1 (Local)
VMICTimeProvider (Local)
DllName: C:\Windows\System32\vmictimeprovider.dll (Local)
Enabled: 1 (Local)
InputProvider: 1 (Local)
Cisco config and errors
CISCO1#show ntp ass det
10.7.0.7 configured, insane, invalid, stratum 3
ref ID 10.7.0.4, time D5BC850F.C8400AB2 (15:50:39.782 MSK Mon Aug 19 2013)
our mode client, peer mode server, our poll intvl 1024, peer poll intvl 1024
root delay 62.50 msec, root disp 11128.04, reach 377, sync dist 11218.796
delay 6.06 msec, offset -467951.1096 msec, dispersion 56.49
precision 2**6, version 3
org time D5BC8864.F79C33A7 (16:04:52.967 MSK Mon Aug 19 2013)
rcv time D5BC8A38.EBDECB39 (16:12:40.921 MSK Mon Aug 19 2013)
xmt time D5BC8A38.EA5173BE (16:12:40.915 MSK Mon Aug 19 2013)
filtdelay = 6.06 5.87 3.23 7.90 6.41 5.17 13.03 3.43
filtoffset = -467951 -467905 -467936 -467885 -467764 -467816 -467707 -467697
filterror = 0.02 15.64 31.27 46.89 62.52 78.14 93.75 93.78Hi,
>>I gave log on as a service right to this account in Default Domain Controllers Policy but unfortunately it was not enough
Based on your description, we can try to grant this account Allow log on locally
user right in the default domain controller policy to see if it helps.
The policy setting is:
Computer Configuration\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Allow log on locally
Allow log on locally
http://technet.microsoft.com/en-us/library/cc756809(v=ws.10).aspx#feedback
TechNet Subscriber Support
If you are TechNet Subscription user and have any feedback on our support quality, please send your feedback here.
Best regards,
Frank Shen -
updated to the new os x mavericks, now i'm having problems with my keychain access...everytime i asked to log in but when i do, it says can't find login items even if i reset it. what should i do?
Did you install the latest driver set for the device? there is a new release on motu.com for mavericks.
rachel
Maybe you are looking for
-
How do I put a PDF form onto my website?
New to Acrobat. Just bought 8 Pro for Mac version. How do I embed a PDF form onto my website? Also, if the process to do this is hard, would upgrading to version 9 make it any easier? Thanks.
-
Problems with character displaying from XML to Java
Hi to all! I am making a flash chat program which basically takes english and chinese and talk to java using XML and java server distribute this message to all users, While simply using java as a distributor of the data was fine, but when I try to ke
-
I cant get captivate 8 SCORM in Peoplesoft lms to start at the beginning after a fail and launching again.
-
No sound in firefox after upgrade to Ubuntu 10.04
no sound in firefox after upgrade to Ubuntu 10.04. Youtube and Vimeo are both affected. Have sound in Banshee and MPlayer. == This happened == Every time Firefox opened == After latest upgrade to 10.04
-
HT1725 Downloading problems! Reply ASAP please!!
I was downloading a movie but i paused the downloading before i shut down the computer. So now when i turned on my itunes again, it says i purchased a movie and that a download is on hold but when i clicked the Download Now button, nothing happens. I