Problem with connection to internet after Belle wa...

After I installed belle on N-08 The connection to internet through Orange is no longer available(it's work fine with Anna).
I've ask again the settings from Orange and save it, but the result is the same "No connection available - The browser can't connect to internet site: http://orange/" 

I had lost Wifi and 3G connection. At the end,
http://europe.nokia.com/find-products/nokia-belle-update/nokia-belle-update-faq
"SPB Monitor" was closest to the solution. I deactivated all subdirectories in \private\ in all drives (phone, cards) even so they were not the ones mentioned. I restarted the phone, created an access point and could connect.
Eight hours of my life devoted to Nokia Belle configuration and four days without functioning phone. Hope Nokia is worth it.

Similar Messages

  • Problems with connecting to internet after power loss w WRT54G v3

    I'm having problems connecting to the internet after a power loss with my WRT54G v3 wireless router.  I'm at the latest firmware version (4.21.1). 
    I found similar problems with the V2 version of this router. 
    After a power failure, I can access the http interface to the router,all of my settings are there (not set to factory settings),the unit is connected to my ISP provider,I can ping from the router, but none of my wired or wireless PCs can ping.
    To "fix" this condition, I have to reset to factory settings, then re-load my saved configuration.This usually works, but sometimes I have to hard reset the unit.
    Anyone having this problem? Anyone have a fix?

    Sudden loss of power for extended periods of time will 9x out of 10 will corrupt the saved configurations and can only be fixed in the way you already described.
     A solution for this is getting an UPS incase of a power failure your equipment will be on battery back up until either the battery runs out or power is restored (depending on the model changed the battery time)
    With Knowledge… Impossible means nothing.
    Credentials
    Computer experience: 11 years
    Cisco networks experience: 8 years
    Network administrator: 6 years
    N.E.T. networks experience: 6 years
    Linksys networks experience: 6 years
    Recent additions: A+ | Networks+ | Linux+ | Security+

  • Problems with connecting to internet

    maybe i won't have internet for long so i have to make this quick:
    1. I use bcm43xx kernel module to connect to internet and this has been going OK(sometimes iv'e had to disconnect and reconnect to still get internet however) nut completely died this morning.
    2. the internet is coming into a black box(get.no cable internet box) and is passed from there over to my wifi-router.
    This has been working but due to today and the fact that i need internet all the time(because of work) i bought a new router(which is supposed to be "the best" and cost accordingly...) and replaced the old one because i suspected it to have died.
            After some fiddling around i get this one to work.
    Now some hours later, i don't get internet stable anymore. The connection drops each time this msg is printed to /var/log/messages.log(inotail -f FTW!):
    Sep 26 23:25:34 garbagepailkid SoftMAC: Authentication timed out with 00:1b:11:68:db:b1
    (what is this softmac??)
    I use wifi-radar to connect -- and would _really_ appreciate a little guide on how to connect to the internet through cmd-line(and an explanation of what the cmd's do would be even more appreciated) as it would enable me to be more in control with a larger ability to troubleshoot this -- but maybe the problem lays elsewhere.
    This is what happens in messages.log when i try to connect through wifi-radar and fail:
    Sep 26 23:31:26 garbagepailkid ADDRCONF(NETDEV_UP): eth0: link is not ready
    Sep 26 23:37:07 garbagepailkid dhcpcd[30155]: eth0: dhcpcd 3.1.4 starting
    Sep 26 23:37:07 garbagepailkid dhcpcd[30155]: eth0: hardware address = 00:30:bd:f9:39:87
    Sep 26 23:37:07 garbagepailkid dhcpcd[30155]: eth0: broadcasting for a lease
    Sep 26 23:37:37 garbagepailkid dhcpcd[30155]: eth0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-eth0.info'
    Sep 26 23:37:37 garbagepailkid dhcpcd[30155]: eth0: checking 169.254.200.102 is available on attached networks
    Sep 26 23:37:38 garbagepailkid dhcpcd[30155]: eth0: adding IP address 169.254.200.102/16
    Sep 26 23:37:43 garbagepailkid dhcpcd[30156]: eth0: broadcasting for a lease
    when i succed(this happens after an arbitrary amount of connects&disconnects through wifi-radar but now it doesn't work at all it seems...) i get an 192.168.0.x ip... and it also says ADDRCONF(NETDEV_CHANGE) <-- What is this?? How do i modify this one?
    any help appreciated...
    ps: just noticed. it seems to go up if i disconnect fast(still from within wifi-radar) and click connects again immediatley

    hmm... i now connect with my little trick above. disconnect & then connect fast again so i don't know if thats the reason i haven't had trouble anymore but i rather suspect it is because of the bug with bcm43xx that were fixed with the 2.6.22.9 kernel which upon installation iv'e had no problems, since i don't suddenly lose connection like i did before

  • Problem with Connecting to VPN after migrated to snow leopard

    Hi,
    I recently migrated to Snow Leopard server, I have a strange issue when connecting to the VPN Server.
    Please find the below error.
    Fri Jan 1 14:38:22 2010 : CHAP peer authentication succeeded for jasmine
    Fri Jan 1 14:38:22 2010 : DSAccessControl plugin: User 'jasmine' authorized for access
    Fri Jan 1 14:38:22 2010 : MPPE required, but keys are not available. Possible plugin problem?
    Fri Jan 1 14:38:22 2010 : sent LCP TermReq id=0x2 \"MPPE required but not available\"
    Fri Jan 1 14:38:22 2010 : Connection terminated.
    Fri Jan 1 14:38:22 2010 : Connect time 0.0 minutes.
    Fri Jan 1 14:38:22 2010 : Sent 0 bytes, received 0 bytes.
    Fri Jan 1 14:38:22 2010 : PPTP disconnecting...
    Fri Jan 1 14:38:22 2010 : PPTP disconnected
    2010-01-01 14:38:22 IST --> Client with address = 192.168.1.76 has hungup
    Please let me know what is the cause and how can i fix it.
    Thanks,
    Gulab Pasha

    More often than not when a device isn't working it is because the driver has become corrupted. Re-installing a fresh copy should help
    http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isnt-working-properly?SignedIn=1
    http://captaindbg.com/how-to-update-drivers-on-windows-7/   (works on win 8 too)
    Wanikiya and Dyami--Team Zigzag

  • I'm having problems with my mobile internet connection

    I'm having problems with my mobile internet connection. Wifi works fine. It seems like my connection get lost every tuesday and friday between 11 and 12 am local time (guess it would be between 2 and 3 am Los angeles time for example). The connection won't comeback by itself. I have to turn the phone, iPhone 4s iOS 5.0.1, off and back on again. The connection immediatly works fine after the restart and stays fine for days. I really don't know what to do. My provider doesn't seem to know either. Tried a lot of things, new settings, resets, I even got a new iPhone. Still the same problem however. Richt now I changes the time setting to see it the problem occurs at another time. Btw: the phone doesn't say "no service" and I can send sms messages and make phonecalls. The 3G symbol or the circular symbol is shown next to the name of the provider.
    Does somebody has an idea what this might be? Thanks a lot.

    Update. My carrier says the antenna of my iPhone 4s is not so good as the one in the iPhone 3G. They can't solve the problem. Their signal is too weak for the 4s at places I spend most of my time. Not the answer I expected, but I'm free to choose an other carrier. Hope this will help.
    This was not the correct answer, I accidentially clicked the button..
    Message was edited by: vasch

  • Problem with Rescue and Recovery after installing Norton Internet Security 2010

    Hi all.
    It's my first time in this forum.
    I have a problem, with Rescue and Recovery, after installing Norton Internet Security 2010 on my T43.
    The message I get it:
    "Rescue and Recovery is unable to back up the file 'C:\Documents and settings\all Users\Application Data\ Norton\ 00000082\00000109\000003c1\cltMLS1.bat' Because the file is either corrupted or being used by another application. Please close any application that could be using the file.
    I tried to close the Norton but I couldn't find how.
    Tanks
    Doron71

    Hi and welcome to the forum,
    the reason for this situation is, that the antivir files are protected from being modified.
    This is the reason, why this file cannot be backed up. I assume, that you would get much more such messages, as there are surelly multiple files files, that are protected like this.
    So the solution is to block folders from being archived. Please start RnR application and in the configuration set this folder as the excluded one.
    This will skip the backup of this file and will fix your situation.
    Please let me know, if you have covered this.
    Cheers

  • Problem with connecting to free wifi after upgrading to Windows 8.1 from Windows 8

    Hi
    I had problems with connecting to free Wifi after upgrading my PC(Notebook) to Windows 8.1 from Windows 8. As I travel a lot within europe, I am used to being able to connect to Free Wifi(those that dont need a key or password to enter) but soon after downloading
    Windows 8.1 I almost never was able to do this. I'd always get «LIMITED» even though the signal was strong.This was so fustrating,so much so that I reset my PC to clear it of Windows 8.1 and am now back to Windows 8.This is a shame because I was really liking
    using Windows 8.1 and if not for this problem(which is a big one) I'd still be using it. If I download Windows 8.1 again from the Windows store what is the probability that I'll have the same problems?
    Thanks Portozzygirl

    More often than not when a device isn't working it is because the driver has become corrupted. Re-installing a fresh copy should help
    http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isnt-working-properly?SignedIn=1
    http://captaindbg.com/how-to-update-drivers-on-windows-7/   (works on win 8 too)
    Wanikiya and Dyami--Team Zigzag

  • After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

    After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

    1. Download the iOS 5.0.1: http://www.tobias-hartmann.net/2011/11/download-ios-5-0-1-veroffentlicht-direkte -downloadlinks/
    2. open itunes,Click in iTunes while holding down the Shift key (on Windows) or Alt key (Mac) to restore and firmware

  • Problem with connecting ipad 2 with crestron cp2e...help plss its urgent... I hv a ipad 2 with mobile pro g connected with cp2e. when i pressed any button in ipad its connet with cp2e but after 4-5 sec one error comes (warning wifi was powered off while t

    problem with connecting ipad 2 with crestron cp2e...help plss its urgent...
    I hv a ipad 2 with mobile pro g connected with cp2e. when i pressed any button in ipad its connet with cp2e but after 4-5 sec one error comes (warning wifi was powered off while the device was in auto -lock(sleep)press connect to reconnect) when i pressed again its connected with cp2e. i am using netgear wireless access point . i also has been changed access point as well as updated ipad firmware bt problem is as it is .. pls help.

    Hi have you solved the issue ?
    Cause I have the same problem.
    Tnx

  • Problem with not getting Internet Connect on AirPort Express

    Problem with not getting Internet Connect on AirPort Express (version7.6.4). Error says cannot get valid IP address. Have reset Siemens SpeedStream 4100 several time, even with tech support from the big "A" DSL provider. Plug MacBook Pro directly into modem and works fine. Unplugged AirPort, even reset it, still no luck. A bad Express?? or am not looking in the right place to make connection. Was working fine up until Sunday.

    Connect the AirPort Express (AX) to the cable modem via Ethernet cable.
    In configuring the AX using AirPort Utility:
    Under Internet, set the connection to be Ethernet using DHCP.
    Under Connection Sharing, set it to distribute a range of IP addresses.
    Under AirPort>Wireless, set the Wireless Mode to Create a wireless network, and fill in the remaining settings in the same window. Until you get it working, you might want to set Wireless Security to None.

  • Firefox will not connect to internet after upgrade. The window pops up but shows "connecting " in tab. And then it sit there. Close it down and then try to reopen it and get message " Firefox already running, Exit program or shut down computer" ???

    Firefox will not connect to internet after upgrade. The window pops up but shows "connecting " in tab. And then it sit there. Close it down and then try to reopen it and get message " Firefox already running, Exit program or shut down computer" ?????????????????

    1st problem see http://kb.mozillazine.org/Firewalls
    2nd problem, to close Firefox properly use File > Exit
    :not with the [x] in upper right corner which close window
    :see http://kb.mozillazine.org/Firefox_hangs#Hang_at_exit
    :if restarting use "Restartless Restart" extension as mentioned there.
    <br><small>Please mark "Solved" one answer that will best help others with a similar problem -- hope this was it.</small>

  • My brand new Macbook PRO i5 can't connect to internet after sleep? It works fine after reboot.

    I have a brand new Macbook PRO with the latest OS and the latest EFI. I haven't installed any 3'rd party products except Moneywell for my private finances. After a couple of days it couldn't connect to internet after sleep. I run the network diag and it says the connection is OK. Log out/in doesn't help. I have to reboot everytime it wakes up after sleep. Any clue?
    br,
    DAVID

    I am having the exact same problem.  It started with 10.7, was fixed with 10.7.1, then came back again with 10.7.2.

  • OS X 10.7.2 very slow to connect to internet after sleep

    Following the lates round of updates and firmware updates MacBook Pro Running 10.7.2 is very difficult to connect to internet after sleep. Network diagnostics show all is fine, all the IP's DNS etc WiFi are fine Safari just won't connect. Was fine before updates

    I have had this same problem since I updated to lion. I used to connect straight away. Now it takes at least 10sec.
    Have noticed a few anoying bugs with lion. The other thing that somtimes happens to me is it crashing when running some programes ( iphoto '08, BBC iplayer desctop etc... ) and also when browsing some sites (quite alot on youtube)
    Really hope these are sorted on the next update.

  • Cant connect to internet after ios6 update

    cant connect to internet after ios6 update

    iOS 6 Wifi Problems/Fixes
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting
    http://www.apple.com/support/ipad/wifi/
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Problem with connecting and syncing   (quicktime.qts)

    Hi,
    I have a problem with connecting and syncing my Iphone to itunes.
    iphone alone on PC -> uploading files (fotos) is possible
    itunes starts normaly, if iphone is not conected.
    if i connect iphone after starting itunes, or if i start itunes after connecting iphone i get an itunes-error with message:
    AppName: itunes.exe AppVer: 9.0.2.25 ModName: quicktime.qts
    ModVer: 7.65.17.80 Offset: 00909a47
    i test different things...
    - used another USB-port
    - used another PC
    - used macbook of my wife instead PC
    - deinstalled and new installed of itunes (older and newer versions) folow tutorials of apple
    - use another USB-Cable...
    I'm resigned, Please help me..
    Tom

    AppName: itunes.exe AppVer: 9.0.2.25 ModName: quicktime.qts
    In this context, that can sometimes indicate trouble with a content file on the phone (or Touch).
    Do you have any podcasts stored on the iPhone at the moment? If so, if you delete them from the phone, can you connect to iTunes without the error?

Maybe you are looking for