Problem with creating an Infrastructure Network (via Access Point) for WLS 9163.

Hi,
I am trying to connect the WLS 9163 to an Infrastructure Network (via an Access Point). I have connected it via an Ethernet cable and am using MAX to configure it.
The setting are as below:
Obtain IP Address through: DHCP
Country: US
Radio On: Yes
SSID: wireless (selected from drop down implying the wireless network is detected)
Wireless Mode: Infrastructure
Authentication: Open
After doing these settings, I click on Save Settings. The device reboots itself and takes the IP address, Subnet mask and default Gateway automatically. The WLS link LED on the device is also turned on. The System State is 'Connected' and both the Wired and Wireless Connection Status is shown as 'UP'.
So far so good.
Now if I remove the wired connection and refresh the device, it does not get connected via wireless (which I believe it ideally should). The System State is shown as Disconnected.
I am using a Phoenix Contact WAP and have set the authentication as Open.
Please suggest some solution.

I had this exact same problem and it took me a while to figure out. As strange as this sounds, I figured out that for some reason if I had the WLS-9163 too close to the router and I pulled the wired connection, the wireless connection could drop. I read on a post in a different forum about someone removing their antenna and it working just fine so I tried that and it worked off and on but mostly off. So I figured out that the further distance away I was the better the connection stability was and I got far enough away from the router to where it was a steady solid wireless connection. This sounds really backwards from what it should be and was really bizarre but I tried different routers, used all different types of settings, had the latest firmware and had all of the equipment sitting on my desk and could not get it working once I removed the wired connection. This may not solve your problem but this worked for me so I thought I'd share that info. I was just so shocked to figure out being too close to the router seemed to be screwing my stuff up.

Similar Messages

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

Problems with static IP from TP-Link Access Point

Hello Guys!
I'm new with Apple - i got a Macbook Pro Mid 2012 since 2 weeks.
Everythings running fine and im really happy with the Macbook - except of the Wifi.
I have the problem that the internet connection is just working temporarily, sometimes its just working for 1 minute, then its just stopping. im still connected to the wifi, no connection abortion. websites are just not getting loaded or just half.
i cant find a solution for it, so please help me
I connected a TP-Link tl-wa801nd with a ethernet cable to our companys network - creating a wifi network access point with which i can connect to with my devices (Macbook Pro, iphone and Win7 PC)
I have to give my devices a static ip, when i want to connect with it:
IP: 192.168.0.151 - 192.168.0.199
Subnet mask: 255.255.255.0
Router and DNS: 192.168.0.1
These preferences are working perfect with the iphone, Win 7-PCs and some friends Android or BB phones. No problems.
Except of the Macbook pro:
I got the newest Mavericks on it and the same network preferences (except of a ascending ip address and the search domain 192.168.0.1)
But like i said above - network is just working temporarily, sometimes for 1 minute, then stopping for 10 minutes... The problem must be the macbook, because every other devices is working fine.
Thank for your helping answers
banana-benjiro

Hello banana-benjiro,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Safari 5.0.1 or later: Slow or partial webpage loading, or webpage cannot be found
http://support.apple.com/kb/ts3408
Best of luck,
Mario

IOS 6.0.1 - Problems with certificate based authentication on wireless access point

Hi all
We are using iPad 2 as order terminals in our shops for about 5 months. Some of the iPads (the first who entered the field) started to cause problems now. These iPads are no longer able to keep long-term connection to the wireless access point in our stores. After selecting the SSID a successful authentication using the stored EAP-TLS certificate is performed (this can be seen in the log files of our wireless controller and by the IP adress that is given by DHCP). But within seconds the affected iPads opening up a captive portal page (empty, without contents) and separates the connection to the SSID after a short time again.
Affected are currently only iPads 2 with iOS 6.0.1, which were staged about 5 months ago. The newer devices with iOS 6.1+ connect without problems and open no captive portal page. The first cases occurred on the last Wednesday. Before that everything worked without difficulty. No modifications took place on the security structure. The numbers of affected devices increased until all iOS 6.0.1 were affected.
Access to other SSIDs (without use of certificates, by entering a key) for the devices is still possible (the devices does not open an captive portal page). The DHCP scope is not used up, so there are enough IP addresses available.
"Newer iPads" with an iOS of 6.1+ are are showing no problems on the same wireless access point, where the older devices are rejected. New and old devices use the same certificates and authentication mechanisms.
In the analysis of the issue, it turned out that the problem can be solved by an update to iOS 6.1.3. Subsequently, the iPads will be able to rebuild a connection with the access point, without a captive portal page.
Since the bandwidth is very narrow dimensioned in our stores, the communication of the iPads was severely restricted. Thus, the iPads are for exampleare accessible for the APNS but can not find iOS updates or check for their availability.
A comprehensive update to iOS 6.1.3 is currently excluded.
Does anyone knows this issue? What else can be done (except from updating)?

I will answer my own question in case it helps anyone else.
It would "seem" the ios 6 devices try the proxy and if that is not working they resort to the def gateway.
To Fix I did the following:
Brocade WIFI network has IPS and Advanced Firewall rules that seemed to be tthwarting some traffic, the iphones would then try the default gateway and be blocked at the FW.
I disabled the IPS and the Advanced Firewall Settings on the wifi as they are redundant to our main IPS and firewall that all traffic flows through anyway. I will tune it later, but when the CEO is demanding a fix "**** the security, full speed ahead"
Created some rues on the firewall to allow...
- IMAP-SSL (port993) outbound
- SMTPS (port 465) to yahoo servers outbound
- tcp port 587 to yahoo servers outbound
- https to akamai servers
Most http and https goes through the proxy as it should, BUT...
It seems that the akamai traffic allways ignores the wifi proxy settings and just heads straight for the default gateway. I suspect there is a bug in the icloud app?
Hope this helps someone else.
-Bo

IPhone has constant problems with Computer-To-Computer network

I use a Computer-To-Computer network to connect my iPhone with my MacBook Pro when I'm at the office. This enables syncing of Things and OmniFocus between my iPhone versions of these programs and the versions on my MacBook Pro. I have one of the original (2G) iPhones. I daily go to my Airport icon on my Mac's menu bar, click on Create Network, and set up a password. I'm using 40-bit WEP.
This sort of syncing procedure worked fairly well until iPhone OS 3.0. Ever since then, it's been completely unreliable. I've tried changing the channel a number of times, and of course rebooting both the iPhone and the computer dozens of times. It's still a problem.
Anyone heard of this networking problem with 3.0? Any info appreciated! Thanks.

yes, i have been having problems with computer to computer networking to iphone as well. for now, the only thing that keeps a steady connection is removing the sim card, so keep a paper clip handy.

Problem with creating chapter-markers

Hi everyone,
as the title already says it, I've got a problem with creating chapter markers in Quicktime Pro 7.6.4. There's something wrong with the font, displayed in Quicktime. The problem first appeared a few days ago. Before this, everything went fine and I don't have a clue what causes the problem.
Please click HERE to see a screen-recording of the steps I do to create chapters:
- convert the chapters into unformatted text and save it as Unicode (UTF-16) text file.
- open it in Quicktime and everything (including the german umlauts) is displayed correct.
- export it into a Text-file with description
when I open the new text file in Quicktime, the fonts are displayed in asian letters, but when I view it in the Texteditor, the text is almost correct, BUT the umlauts are not ok. So I go on with...
- correct the umlauts and save a new file as Unicode (UTF-16) again.
After I open the new file in Quicktime, the text is completely gone. As the text file seems to be ok in the Texteditor, I guess there must be something wrong with Quicktime. I tried to reinstall Quicktime 7 from the "Mac OS X 10.6 Snow Leopard" Installation-Disc, but the problem persists.
I' would appreciate any help...
Thanks in advance and best regards,
Michael

I'm having the exact same issue. I have created my movie in IMovie 09 then under the "share " menu I sent the movie to iDVD. Everything looks fine on screen, but all I get on the final product is the movie.
After digging deeper into the tutorials all they show is dragging a movie into the idvd shell, not sharing via imovie.
Thus I'm currently attempting to create a quicktime movie then drag it into the IDVD shell. I think that way the chapter markers and everything should show up and burnt into the final project. I'm guessing the "share" option with the IDVD from iMovie doesn't work properly???

I am having problems with creating my apple id. On the phone it is advising me that the ID is not created and then when i do it online it says that it has been created. Can you advise me on what to do please?

I am having problems with creating my apple id. On the phone it is advising me that the ID is not created and then when i do it online it says that it has been created. Can you advise me on what to do please?

Apple ID FAQ http://support.apple.com/kb/HE37

Problems with the vba command sendkeys in Access 2013.

Hi, I have problems with the vba command sendkeys in Access 2013.
I use a text field (no control) in a form. By means of the VBA command SendKeys "+ {DELETE}", 1 I get the text in memory from the text field, then place (paste) the text in a Word document. The command line sendkeys
is followed by moving the focus to a particular control. In Access 2003, which went smoothly. Now the sendkeys command is executed only in Access 2013 in the control that then receives focus. If the procedure ends with the sendkeys command then it works well.
The procedure with the sendkeys command is activated by a button on a form.
Who can help me?
private user

Hi H.Plmp,
Based on the description, you want to call the sendkeys from a button.
>> use a text field (no control) in a form. By means of the VBA command SendKeys "+ {DELETE}", 1 I get the text in memory from the text field<<
What did you mean that you no control? And how did you get the text in memory from the text field? Also I am not able to understand the exact reason that the command doesn't works in Access 2013.
And based on the test, sendkeys "+ {Delete}" works well for me when I set a focus for the textbox control. Here is th test code:
Me.Controls("txtField1").SetFocus
SendKeys "+ {DELETE}", 1
If I misunderstood, please feel free to let me know.
Regards & Fei
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Problem with create universe on Business Objects XI 3.1 base on SAP Query

Hello,
I have a problem with create universe on Business Objects XI 3.1 base on SAP Query.
The problem is hierarchy. Massage on Busines Objects is :
OWBS_ELEMT__ISTKOSZT(cube ICPC01/BEX_ICOC01):Exception condition "HIERARCHY NOT FOUND" raised.(WIS 10901)
Query in BEX run OK.
Best regards.
Ela.

Hello,
Thanks for response.
When I run BEX QUERY, all works OK.
All hierarchies was created and activated on system BW.
This situation appears after upgrade BW to SAP NetWeaver 7.3.
Before upgrade I created universe without any problems.
Regards Ela

Problem with creating new user in portal = portlet is not visible

Hi,
I've got a problem with creating new users in portal. In the Administer tab of the builder is the user portlet not visible.
How can I make this portlet visible?
Please Help
thank you...
Gilbert

Hi..my problem slightly similar.
I created one new user, and didn't select anything from "Public Groups Assignment" and "Privilege Assignment" for him.
I expect the user will be a public user.
But, when he try to logged in the portal,
He cannot see all the PORTLETS related to database values..
All he can see just LINKS -that all in my portal right now beside the report from database that the user cannot see :)
So, what did i do wrong?
Plz Advise, and thanks.

Problem with creating site from another computer!

Hi
I have WebDB 2.2 and Oracle8i instaled on the same computer. I have a problem to create site from another computer. There is not any process when I try to create site. There is always 0%.
But I have no problem with creating site on the origin computer.
Does anybody know something about it?

I am just not clear what to do once I have made changes and have published the new information.
You shouldn't have to do anything. iWeb will save the information in the Domain.sites file. You can keep this file in a folder, or even on your desktop and iWeb will launch from a double-click on the file.

Problem with creating email account on E72

I have bought E72 and want to use mine company email - but there is a problem with creating email account in mail program.
Restoring to fabric settings doesn't works.
When I'm creating Gmail account it's OK, but phone doesnt want to cooperate with other accouns:/

Try again without using WLAN. I had same problem, but solved it using GPRS.

Problem with creating order through order template

Hi experts,
We have problem with creating order by order template. Extensions data available in order template is not sent to order. Extension data are showing upto order submission form. But after sucessful creation of order extension data are no longer available in CRM-ORDEr.
We are using ISA 4.0 with CRM 4.0.
We recently applied patches on CRM server. Before patching it was working fine.
Can you please suggest us to solve this issue?
Thanks in Advance.
Regards,
Murugan Arumugam.

closed.

Problem with Creating Info Record

Hello Gurus,
I've problem with Creating Info Record
i tried to create info record for Plant Specific/Purchase Org
The first Screen General Data is OK
i entered all the data in the next screen ie
Purchase Organization Data screen but i'm getting error
<b>Make an entry in all required fields</b>
but there is Mandatory Textbox ie "VALID TO" which im unable to select Bcos its Disabled
pls help me regarding this
thanks in advance

Hi
Have u given the net price. <b>VALID TO</b> is the date until which the price shown in the info record is valid.
If there is no price that is valid on the current date, the last-valid price is displayed and the date field contains the day before the start of the next validity period (this may be 12.31.9999 if there is no further validity date). If all validit periods lie beyond the current date, the price of the next period is displayed. The date field then contains the end date of this period.
These validity periods we will maintain Purchse data CONDITIONS while creating info record. Check the validity period for the conditions.
Hope this will helps u
Ravi
Ravikumar Bolla

Problem with creating virtual column

Hello,
We've got problem with creating virtual column.
There is table R_T that contain columns R_ID and L_ID, we would like to create virtual column RL_ID that contains sth like 'R_ID-L_ID' (R_ID, L_ID and RL_ID are varchars).
According documentation we've tried:
alter table R_T add column (RL_ID varchar2(60) generated always as (R_ID||'-'||L_ID) VIRTUAL)
but getting
ORA-00904: : invalid identifier
00904.00000 - "%s: invalid identifier"
Have no idea where is the problem.
Table, columns names are little different but contains only capital letters A - Z and underscore "_".
Has anyone idea?
Thanks a lot.

Strange...
This does work for me :
Connected to Oracle Database 11g Enterprise Edition Release 11.2.0.1.0
Connected as dev
SQL>
SQL> create table r_t (
2   r_id varchar2(25),
3   l_id varchar2(25)
4 );
Table created
SQL> insert into r_t (r_id, l_id) values('R','L');
1 row inserted
SQL> alter table r_t add (rl_id varchar2(60) generated always as (r_id||'-'||l_id) virtual);
Table altered
SQL> select * from r_t;
R_ID                      L_ID                      RL_ID
R                         L                         R-L
SQL>

Problem with creating an Infrastructure Network (via Access Point) for WLS 9163.

Similar Messages

Maybe you are looking for