Problem with fan speed on FM2-A75-P33

I have a problem with setting a lower cpu fan speed on my motherboard (Win7 64).
It always runs on high speed, and I can not decrease it. When I set values for min speed in ClickBios II (or manually in Bios before booting) to 0%, and desired temperature on some higher amount (60C), nothing happens. It always run on same high rpm, regardless any change of values. What can I do? Same thing with sys fan.
Live Bios says that I have latest version of BIOS and drivers.
thanks

That is odd. Only thing I can think of is maybe a conflict in settings between Click Bios and actual BIOS. One of the reasons I never use those programs. I'm not sure what to tell you, except that the fan speed settings on my board have all worked properly using standard BIOS settings.
If I was having issues I'd uninstall click BIOS and see if the issue continues. At least then you would know it's something else.

Similar Messages

HP Probook 6540b problem with fan speed and sound card

Hi.
Sorry for my English.
I have installed Arch 32bit on probook 6540b (it has core i5 processor). Cpufrequtils works well - with governor set on ondemand frequency is adjusting correctly but fun is running max speed all the time. I have tried to configure lm_sensors but it doesn`t detect any sensors. Also fun folder in acpi is empty. It would be great if You could help me.
Thanks for any advice.
...ergh
Fan sometimes works slow so maybe its overheating problem.
But
I have another problem with sound on this laptop. I have IDT 92HD75B3X5 sound chip and snd-hda-intel module loaded for it but it doesn`t make any sound. In Amarok it looks like something is playing because progress bar is moving. I have tried everything from arch wiki and other sources but nothing works. Maybe You can help?
Thanks
Last edited by zennon (2010-08-22 08:57:07)

Hi. Yes. I also tried all tricks with model etc. and nothing. Now I have installed oss and have some progress. I have sound on pcm2 when I run osstest, no sound on pcm1 (but it looks in test like it plays something) and input/output errors from pcm3 to pcm7. I have oss output in multimedia in kde and when I run test I can see moving strips or something (I dont know the word for it ) in ossxmix but I hear nothing. I I tried all configurations in ossxmix and nothing.
Last edited by zennon (2010-08-23 12:37:23)

MSI R7870-2GD5T/OC problems with fans

Greetings.
I just bought this card and got some problems with fans: when temperature of GPU rises above 52-55 degrees fans start spining at maximum speed.
Tried fix that using MSI afterburner/Catalyst control center - no effect, fan speed showed as I set up, but the tachometer shows 4400 rev / min, which is confirmed by the characteristic sound.
I hope that there is a fix for this beacause i cant RMA my videocard, I accidentaly lost the box, and since I paid 190€ i would like to have some support from MSI.
Thanks.
Edit: Noticed now that here nobody work for MSI, well an help would be great anyway

the Original box doesn't matter if its gone as MSI don't like them in original box as they won't return the card in it.
as long as you have the original receipt from your purchase and the Graphics card your all good....
as for the problem your having it will be a leak current on a faulty safety catch diode (201) as they got a bad batch a while back that when it gets hot it opens the fan circuit to maximum as it thinks the card is overheating. (either remove it carefully (as long as you do not damage the card your warranty is still intact as the removal of that component is what MSI suggested when the issue first showed up) or RMA the card)

IPad2 problem with operating speed.

Hi!
Like in subject. After updating to iOS 8.1.1 my iPad2 work very slow. I restore system but problem with operating speed still there.
Regards
Jacek

Sorted by apple support. Thanks. If anyone is looking at this you set the mail account up using the Microsoft exchange option then type m.hotmail.com into the server.
Bye

Problem with downloading speed on itunes and app store.

i have problem with downloading speed on itunes and app store.ihave 6mb/ps plan.whene i download on xperia z downloading speed is about 3mb/ps.but when i download on apple app store or any apple server it giving only 150kb/ps.im doing everything. i change my ip dynamic to static.but nothing is change on speed.plz help me and give me some use full static ip and dns.

Hi JM_7,
If you are having a space issue when trying to sync your iPhone, you may find the following article helpful:
iOS: "Not enough free space" alert when trying to sync
http://support.apple.com/kb/ts1503
Regards,
- Brenden

Does Lion 10.7.1 fix problems with fan noise and hot in Air 2008 Model?

Does Lion 10.7.1 fix problems with fan noise and hot in Air 2008 Model?
I´ve installed a week ago but i downgraded to SL again. My CPU was hotter and high rpm fan eve in idle state.
Does fix 10.7.1 this issues?
I´ve got first generation macbook air, 2gb ram, ssd 60gb .

Simply NO, we´re still waiting....

Problem with USB speed

Hi there,
I am new to MSI forum, and have some questions.
I have MSI K9NU Neo-V mainboard and have problem with USB speed . I have all the latest drivers installed and the latest BIOS for my mainboard but still have the problem that mainboard detects all USB devices like USB 1.1
MB MSI MS-7270 ver. 1 (K9NU Neo-V)
CPU AMD Athlon 4200+
VGA MSI 8600 GTS
Memory 2 x 512 MB DDR2 667 Corsair XMS matched Pair
PSU Gigabyte GE-R 460 V1
DVD-RW Pioneer DVR 112D
HDD Western Digital WD2500JS
OS Windows XP SP3 x86
Any idea about this?!
Thanks,
Alek

Quote from: Bas on 20-November-09, 21:57:20
Did you install all the drivers listed here?
http://eu.msi.com/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=261
I also move this topic to the right area.
Yes, everything is installed and updated with latest drivers even from nVidia WEB for ULi chipset. the devices that we are talking about are USB removable storage like 8GB USB Flash Drive from Kingmax, 2GB Flash Drive from Xerox, 1 GB USB Flash drive from Kingston, USB case for 2,5" HDD from Spire ... I can count till tomorrow

Dual G5 late 2004. Some problems with fan and freeze and now can't start

I just purchased a late 2004 Dual 2.5 Gig, with PCI-x and 1 gig ethernet. 1 Gig of what I presume to be factory ram and blue toothe. Connected to a new 23" Apple display.
The problems I have been having pale to where I stand now. I am stuck and can't move forward. At this point, the computer is off. When I try to turn it on, it does little to nothing and gradually the fan speed increases until the computer sounds like it wants to take off. The screen either stays dark, or sometimes I see the ? briefly, and then the grey screen with logo and that is where it stops. Currently I can't get past a lot of fan noise??
Can I get this thing started?? I have tried both starting from CD and hard drive. No luck.
This whole mess started yesterday and has continually gotten worse. Those details I can get into if needed, but for now, what can I do to see the screen and start over.
I just bought the machine, and I was doing a clean install that was acting funny. Hard drive sleep mode would cause the machine to not wake up. Specifically it was the monitor that would not wake up. The keyboard and the computer would still respond when I adjusted the volume. The screen was black.
I narrowed the problem to drive sleep, or monitor sleep by using the energy saver preferences. Just the monitor sleeping wasn't the probem. The computer would wake up. But if the hard drive went to sleep, then I could never get the screen back and the computer acted dormant. The only thing I could get was the volume sound from the computer and lights on the keyboard.
I ran Techtool Pro 4.1.2 ( i think ) and it reported possibe problems on the hard drive with the volume. I made the changes hoping that would fix the problem? No.
I decided to flush it all and start over with the install cd, make sure firmware was good, reformat the drive, and then install the System. But instead, I got caught is this loop of death that I can't get out of.
It had a kernal panic the first day I turned it on, but that was the last one. (dark screen with white message) The computer ran rather sluggish at times. I was shocked at times. Very slow finder response.
So? Suggestions? I have searched Apple support and tried anything I can think of. This is my first G5, but I have had some exposure to OSX beginning around 10.2. I am at my wits end and would greatly appreciate some input. For now I have to get some sleep.
Is my battery bad? It just won't start?
Thank you for any help you can provide, or links to articles!!

Hi Lawson, and a Warm Welcome to the Power Mac G5 Forum!
You could try a PMU/SMU reset
http://docs.info.apple.com/article.html?artnum=300341
Use the second procedure if you have a button as shown in the photo - use the first method if you don't. You may not have to remove the intake fan assembly to get at the button. Observe static precautions and make sure to press the button once only.
Then try to start up on the CD/DVD.
If it fires up ok you could then proceed with the 10.4 install as before, and then combo update to 10.4.8
http://www.apple.com/support/downloads/macosx1048comboupdateppc.html
I would connect only a display, wired keyboard and mouse to start with - and disable any of the sleep, etc. Options in Energy Saver.
You may wish to use the Disk Utility on the 10.4 retail disc(under Utilities in the menu) to Erase and zero(select Security Options) the drive before the install.
The kernel panic and other problems could have been caused by a corrupted system on the boot drive, or by hardware problems, such as RAM, video card, battery, etc. Some of the hardware stuff is linked-to further down the post here
http://discussions.apple.com/thread.jspa?messageID=3084827&#3084827
However, try the PMU/SMU reset and erase/install first, and post again with details if you still have problems.

One more time - problems with fans

I realize this is but one of hundreds or possibly thousands of cases of Mac users being plagued by fan noise problems, but to me it has been a long and extremely frustrating saga. I have been a Mac user since the very beginning, through different versions of Macs and iMacs, and this is the first time I ever refer to a Macintosh as a "piece of junk."
I bought my iMac G5 in August 2005, a 20-inch ALS with 250 GB hard drive and 512 MB RAM. It worked perfectly until January this year, when all of sudden it shut down by itself. Freaked me out completely. Turned out to be power supply problem (EMC 2056) which Apple never informed me about.
I brought it to a repair shop that fixed the intermittent shut-down problem. I also added 1GB memory. But then the fans started to go berserk. Before the power supply problem, I only heard the fans whenever I used a large program like Photoshop. For the most part, it was a very quiet machine. After the power supply was replaced, within minutes of turning the iMac on, I could hear the fans spinning faster and faster, stabilizing at around 4400 rpm and did not stop spinning until I put the iMac to sleep or turned it off, regardless of CPU usage or software being used.
I checked the discussions at this forum (over 500 posts, no real answer) and did every "voodoo trick" suggested: I reset the SMU dozens of time, cleaned the inside of the iMac and around the fan area, did apple hardware test (everything was fine), monitored temperature and activity with XRG (average CPU at 160F, hard drive at 113F), cleaned out caches, tested for corrupt preferences, re-installed the original OS 10.4 (which only made the fans louder), upgraded it back to OS 10.4.9. I also removed the additional 1 GB memory, thinking it might be a bad piece. It didn't help.
Finally, I requested fan replacement from Apple and got them. I installed them last Sunday and now the problem is even worse! Within SECONDS of turning it on, the CPU T- Dio soars to around 170F, even while the machine is still stone cold to the touch. The hard drive temperature now averages at 117F, CPU fan is never below 4000 rpm (4400 rpm 98% of the time), even at 5-8% CPU usage.
The fans themselves are much quieter because they're brand new. But you can still hear the hums and whirs and it drives me nuts. More seriously, my iMac is now narcoleptic. If I use it too long (a few hours on a stretch) it will put itself to sleep, apparently because it thinks it is overheated. And when I use Photoshop or Illustrator, the awake time is even shorter. Depending on the outside temperature, at the most I can only use them for about an hour at a time. Two days ago we had heat wave, and even with the air conditioner running full blast in my study, the iMac kept falling asleep within minutes of using Illustrator.
Right now I am using TextEdit and no other program is running. Uptime is 59 minutes, average CPU 9.6%. CPU T-Dio is at 168.8F, hard drive 117.5F, CPU fan at 4400 rpm. I am out of ideas and before I do something drastic to this machine, if anyone knows what's going on with my iMac (I know every case is different), please help!
iMacG5 ECM 2056 Mac OS X (10.4.9) 20"/2.0GHz Power PC/1.5GB DDR SDRAM/250GB
iMacG5 ECM 2056 Mac OS X (10.4.9) 20"/2.0GHz Power PC/1.5GB DDR SDRAM/250GB

I do not have the solution... but the same problem with a nice iMac G5 purchased in July 2005.
My Mac operated very silently untill 6 month ago;problem MAY ( I am not sure) have started when I upgraded to 10.4.10 ; even with few applications and low CPU usage (80% or more inactive), it seems that I have the following regrettable chain of events;
==> the CPU temperature is quite high ( 60°c to 72°c most of the time, ie 140-160 °F)
==> resulting in fan turning at high speed ( 2.000 for CPU and system, 2500 for HD), and changing speed all the time
==> resulting in a noisy computer
I am SURE this was not the case 6 month ago, and I suspect it is linked to my upgrade to 10.4.10.
I did all sorts of reinstall, authorization repair, SMU reset, fan clean-up with no sucess.
iMac G5 (2005) Mac OS X (10.4.10) POwerbook G4 Titanium (2001)

Problems with variable speed

problems with clips switching from constant to variable speed.

Could you be more specific? What are you doing exactly and what is happening when you do it? Which version of FCP?

Help with Fan Speed/Temperature Monitoring - 875P Neo Series 2.0

Hi
My mobo manual doesn't explain the monitoring facilities available on this board and I would like confirmation of the following:
My P4 Northwood CPU Fan as supplied with P4 is connected to CFAN1 and provides monitoring of temperature and fan speed and also permits fan speed control.
My Northbridge Fan as supplied with mobo is connected to NBFAN1 and provides monitoring and control of fan speed. No temperature monitoring available.
My mobo provides monitoring of system temperature but doesn't say how this is measured and at what location.
There are two other 3-pin fan headers on the mobo; one is labelled SFAN1 with Gnd, +12V and the third pin NC and the other is labelled PFAN1 with Gnd, +12V and Sensor pins.
My new Antec 500W SmartPower 2.0 PSU has a monitoring cable that is wired with a black Gnd wire and a blue Sensor wire and, according to the Antec manual, is supposed to provide fan speed monitoring if connected to PFAN1 - I have tried this and get no information showing in either SpeedFan or Sandra. ???
My new Case fan, an Antec SmartCool, also has a monitoring cable but only has the third pin wired, presumably a sensor wire, and presumably could also be attached to PFAN1 instead of the PSU signal connector to provide fan speed monitoring. ??? Obviously I cannot connect both the PSU and Case Fan sensor cables to the mobo because the SFAN1 connection has no sensor pin connected; I presume this one is just a power supply to a fan as an alternative to using a supply line direct from the PSU.
Can anyone advise me on the correct use of the PFAN1 and SFAN1 connectors and what they are capable of.

- System temperature is measured at the Winbond W83627HF sensor chip located in front of your PCI slots.
- PFAN1 does indeed monitor PSU fan speed if the PSU has a fan speed reporting header. Not supported by some monitoring software (if Speedfan can't detect it, it doesn't support it. At least not until Alfredo's next revision).
- SFAN1 provides power only, no monitoring.
- Try a different monitoring software and see if it can detect the sensor monitoring your PFAN1. There are other monitoring software out there you can try, such as the CoreCenter that came with your motherboard, or Motherboard Monitor 5 or PCWizard (though you cannot adjust fan RPM through those programs).

Problem with Fan Running

I'm having problems with my new(ish) iMac. This problem is a bit involved so please bear with me.
While adding a torrent to my downloading program azureus, my computer froze. It would not allow me to shut down or do anything. So I unplugged the machine and waited awhile and attempted to restart. To my horror, it would not start up. I then unplugged the power cord in the back and held the power button while plugging the cord back in and then released and pressed the power button again. My computer turned back on, hooray, BUT, now the fan is running very loudly and has not stopped. I restarted, shut down and left it alone, and now I'm very confused. Any suggestions?
thanks
-Lisa

Hi Lisa!
You should go to this link: http://docs.info.apple.com/article.html?artnum=301733 - you've basically reset the SMU on your machine but read the article and follow carefully. You should go ahead and reset the PRAM, which is also covered in the article.
Rick
Message was edited by: JMEH
Next time this happens, just hold the off button for a few extra seconds and your Mac will shut down.

Problem with fan Trap.

Hi all,
I am having a problem resolving fan trap.
I am having a universe build over a MY SQL database.
The universe totaly consists of 4 tables and are related in the following way.
"A one to many B one to many C many to one D"
There are many 1-may joins between A and B and also between B and C.
There are measures and dimensions in A, B. And in C there are only measureas and 1 dimension.
When I pull the objects from all the three tables (A,B and C) there is a fan trap occuring and the values are getting inflated.
So I created an alias for B and defined a context for A, B and B alias and A,B and C. I have also checked the option of "Multiple SQL statements for different contexts."
But then I am trying to build a report in WebI and pulling the objects from both the unvierses there are 2 queries being generated and in the report, I am not able to pull the objects from different contexts into the same table.
If I select an object that is in context-1 the objects that are defined in context-2 are being dissabled and vise-versa.

You can set this behaviour in the universe parameters under SQL->Multiple paths->Allow seleciton of mutliple contexts .
Still since you are solving a fan trap you should keep this option clear.
A solution is to fetch the data from 2 different contents using 2 different webi queries and then use the Merge dimensions functionality in the report itself to join the results.
Regards,
STratos

Problem with fan, temperature and battery after the restore from the stop (Macbook pro 15)

From a couple of weeks my macbook pro (15" 2.4 Ghz i7 4gb OS X 10.7.4) has this problem: when i close the screen it goes to stop and when i open it goes out the stop normaly but the fan and the temperature increase and the battery last nothing. So i reboot the mac and everithings go to normal way and also battery time increase in comparison with before...

I've found that samsung kies wifi started at the login and that the app used 91% of my cpu and filled up my ram so i went to: system preference > users and groups > login's elements > and i deleted the app from the list.

Problem with fan

Gday all, Not a major problem i dont think but, the north bridge fan on my board just started having speed fluctuations to almost stopping. Atm its running between 7100 to 5200 and the mb temps at 42c, and doesnt sound too good either. Im guessing it s on its way out. Is it difficult to fix, replace? any help would be grand...thanks in advance!

i gave it a good clean n seems to have stablised, sounds a tad rattlely though. Ill buy a spare just in case, thanks for the reply

Problem with fan speed on FM2-A75-P33

Similar Messages

Maybe you are looking for