Problem with fax rely bitween two Cisco 5350

I have two cisco 5350 with the following setting:
Originating cisco :
voice service voip
fax protocol t38 ls-redundancy 3 hs-redundancy 0 fallback none
dial-peer voice 1 voip
huntstop
destination-pattern 111
session target ipv4:xxx.xxx.xxx.xxx
tech-prefix 011
fax rate 4800
fax protocol t38 ls-redundancy 3 hs-redundancy 0 fallback none
no vad
Terminating cisco :
dial-peer voice 71 voip
huntstop
incoming called-number 111
fax rate 4800
fax protocol t38 ls-redundancy 3 hs-redundancy 0 fallback none
no vad
voice service voip
fax protocol t38 ls-redundancy 3 hs-redundancy 0 fallback none
So using such settings i can not send faxes.
How can i find the problem ?

Hi,
I tried to use ls-redundancy 0 but - no result. When the faxes tring to connect to each other - i can hear the tones, but it looks like short tone and then silence.
Also i use the following commadns to solve the broblem:
-fax nfs 000000 at voip peer, fax interface-type and fax interface-type fax-mail. But no result also.

Similar Messages

  • Problem with fax t38 protocol

    hi
    i have an mpls nework with equipment cisco 2821, 2901 and 2801, and i have problems with fax calls, i configured the fax protocol t38 in all routers but when i want to send a fax to the 2821 equipment from either 2801 and 2901, the protocol t38 is not working and the fax call use cisco protocol (although t38 is configured in all routers). the calls betwen 2801 and 2901 works ok, and from 2821 to 2801/2901 works ok too.
    any idea of whats happens? do you think is a problem of ios version?
    these are de ios version
    2821 .-c2800nm-spservicesk9-mz.124-3i.bin
    2801 .- c2801-spservicesk9-mz.150-1.M6.bin
    2901 .-c2900-universalk9-mz.SPA.150-1.M7.bin

    hi
    this is the configuration on the 2821:
    voice service voip
    fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
    dial-peer voice 10037 voip
    description CONEXION CELAYA DISTRITO XV
    destination-pattern 561.
    session target ipv4:172.16.200.37
    incoming called-number .
    dtmf-relay h245-alphanumeric
    codec g729r8 bytes 50
    fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
    ip qos dscp ef signaling
    no vad
    this is the configuration on 2801
    voice service voip
    fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
    dial-peer voice 10016 voip
    description CONEXION VOZ A FAXES
    destination-pattern 300[1-6,8]
    session target ipv4:172.1.1.51
    incoming called-number .
    dtmf-relay h245-alphanumeric
    codec g729r8 bytes 50
    fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
    ip qos dscp ef signaling
    no vad
    i want to use T38 because the bandwidth of the fax call is 16K, if i use cisco protocol the bandwidth reaches up 24k, and the router start to drop voice packets
    thanks

  • Problem with config sync between two CSM-S modules

    Hi everybody,
    I have a problem with config sync between two CSM-S modules.
    I am using CSM-S software version 2.1(8).
    The acitve module is used in a 6509 with WS-SUP720-BASE supervisor running software version 12.2(18)SXF12a.
    The standby module is used in a 6509-V with VS-S720-10G supervisor (no VSS setup) running software version 12.2(33)SXI3.
    Failover seems to work fine:
    switch-active#sh modu csm 2 ft                                      
    FT group 1, vlan 398
    This box is active
    Configuration is out-of-sync
    priority 150, heartbeat 3, failover 40, preemption is on
    switch-standby# sh modu csm 2 ft
    FT group 1, vlan 398
    This box is in standby state
    Configuration is out-of-sync
    priority 80, heartbeat 3, failover 40, preemption is on
    The command (on active side) "hw-module contentSwitchingModule 2 standby config-sync" leads to following result:
    switch-active:
    2010-04-14T16:21:45+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56042: Apr 14 16:21:44.223: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Bulk sync started
    2010-04-14T16:21:45+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56043: Apr 14 16:21:44.251: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configurations to Standby CSM, this may take several minutes!
    2010-04-14T16:21:46+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56044: Apr 14 16:21:45.995: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configuration to Standby CSM
    2010-04-14T16:21:51+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56045: Apr 14 16:21:50.831: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configuration to Standby CSM
    2010-04-14T16:21:57+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56046: Apr 14 16:21:56.151: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configuration to Standby CSM
    2010-04-14T16:22:59+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56047: Apr 14 16:22:58.791: %CSM_SLB-3-REDUNDANCY: Module 2 FT error: Active: Manual bulk sync timed out
    2010-04-14T16:22:59+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56048: Apr 14 16:22:58.803: %CSM_SLB-3-REDUNDANCY: Module 2 FT error:
    2010-04-14T16:22:59+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56049:  FT CONFIG SYNC: Failed config sync entity send
    switch-standby:
    2010-04-14T16:21:45+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2475: Apr 14 16:21:44.232: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Bulk sync started
    2010-04-14T16:21:45+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2476:
    2010-04-14T16:21:45+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2477: Apr 14 16:21:44.240: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: STANDBY:Configuration is being received, This may take several minutes!
    2010-04-14T16:21:49+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2478: Apr 14 16:21:48.824: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Receiving configuration from Active CSM
    2010-04-14T16:21:54+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2479: Apr 14 16:21:53.964: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Receiving configuration from Active CSM
    2010-04-14T16:21:59+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2480: Apr 14 16:21:58.852: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Started clearing configuration
    2010-04-14T16:21:59+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2481: Apr 14 16:21:59.400: %CSM_SLB-4-REDUNDANCY_WARN: Module 2 FT warning: Standby: Config Sync does not save running-config to startup-config
    2010-04-14T16:22:00+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2482: Apr 14 16:21:59.400: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Previous configuration are being deleted from supervisor
    The last log message on standby device seems to be correct - there is no CSM configuration after the attempted config sync.
    Our configuration includes about 3500 lines and it is really uncomfortable to keep in sync manually.
    Maybe someone has the same problem?
    kind regards,
    Christoph

    Hi Christoph,
    I am running into the exact same issue. Upon further investigation I've discovered that this is a known bug, CSCtd09117.  You can read more about it here: http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtd09117 .   Apparently this is fixed in ver 12.2(32.8.11)SX323 .
    I haven't had a chance to upgrade yet, so I can't verify the fix, but if it works for you please let me know.
    Regards,
    Brandon

  • Problem with Fax and ATA

    Hi,
    i do not have problem to send Fax to the PSTN, but when I try to receive a fax on the fax machine in port1 of the ATA, the machine never give fax signal.

    Hi Leonardo,
    Have a look at the following;
    Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (SCCP) (2.15.ms, Rev B0)
    Configuring and Debugging Fax Services
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00800c4d1e.html#1016012
    Configuring and Troubleshooting the Cisco ATA 186 with Fax
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml
    Configure Fax Detection Method on the Cisco ATA 186
    Use a web browser and go to http:///dev (for example, http://172.16.104.117/dev) in order to configure the Cisco ATA 186 using the web interface.
    You must configure these parameters in order to configure the Cisco ATA 186.
    Audio Mode
    bit 2 (18)=0 Enable detection of FAX CED (answer) tone and switch to FAX mode for the rest of the call if the tone is detected.
    Hope this helps!
    Rob

  • über problems with Z10 for past two weeks.

    Hi there
    For the past two weeks I've been having major problems with my Z10. I started noticing that my Whatsapp messages were coming through, but not making a sound. I reset and set the notification settings again, but still no luck. I figured since it was a 3rd party app, I'd maybe need to reinstall it. But then I also noticed that my text messages weren't coming through. Then some of my notifications (Facebook, Text message, Whatsapp and email) started staying "unread" even after I'd read them and even marked them as read. In fact, in desperation I even deleted the one text message thread, but it was still showing in my HUB. When I clicked on it it just showed blank since there was no longer a message there, but it wouldn't "disappear" from the HUB. Also, emails come through, but there is no sound or unread notification and I only see them if I check through the "read" emails in the HUB. 
    The only thing that helps for this is when I restart my phone - then all my texts come through, notifications work fine and everything is dandy - for about half an hour, then the same thing starts happening. This is really annoying, because I have to restart my phone several times a day to make sure I don't miss important messages (which has happened during this time). 
    Last week I wiped my phone and restored an update from 2 weeks earlier (when the phone wasn't giving problems), but once again it only worked for an hour max, then it was back to the same old problems. 
    I'm really frustrated at the moment, because what good is a smart phone to me if all it can do is make and receive calls? The ONLY things working properly at the moment (as far as I'm aware) is BBM and making and receiving calls. 
    *desperate*

    Hi there
    For the past two weeks I've been having major problems with my Z10. I started noticing that my Whatsapp messages were coming through, but not making a sound. I reset and set the notification settings again, but still no luck. I figured since it was a 3rd party app, I'd maybe need to reinstall it. But then I also noticed that my text messages weren't coming through. Then some of my notifications (Facebook, Text message, Whatsapp and email) started staying "unread" even after I'd read them and even marked them as read. In fact, in desperation I even deleted the one text message thread, but it was still showing in my HUB. When I clicked on it it just showed blank since there was no longer a message there, but it wouldn't "disappear" from the HUB. Also, emails come through, but there is no sound or unread notification and I only see them if I check through the "read" emails in the HUB. 
    The only thing that helps for this is when I restart my phone - then all my texts come through, notifications work fine and everything is dandy - for about half an hour, then the same thing starts happening. This is really annoying, because I have to restart my phone several times a day to make sure I don't miss important messages (which has happened during this time). 
    Last week I wiped my phone and restored an update from 2 weeks earlier (when the phone wasn't giving problems), but once again it only worked for an hour max, then it was back to the same old problems. 
    I'm really frustrated at the moment, because what good is a smart phone to me if all it can do is make and receive calls? The ONLY things working properly at the moment (as far as I'm aware) is BBM and making and receiving calls. 
    *desperate*

  • Problem with Javadoc gen'in two instances of a sourcefile in the class list

    Hallo,
    I have a set of source files that I'm gen'ing with the ant task javadoc.
    sourcefiles="javadocs/PTConfigServer-root/src/com/palantir/config/util/SshUtils.java,
    javadocs/PTConfigServer-root/src/com/palantir/config/util/StafUtils.java,
    javadocs/PTCommons-root/src/com/palantir/util/Pair.java,
    javadocs/PTCommons-root/src/com/palantir/util/XMLTag.java,
    javadocs/PTCommons-root/src/com/palantir/util/MutuallyExclusiveSetLock.java,
    javadocs/PTCommons-root/src/com/palantir/exception/PalantirException.java,
    javadocs/PTCommons-root/src/com/palantir/exception/PalantirUserMessageException.java,
    javadocs/PTCommons-root/src/com/palantir/exception/VersionMismatchException.java,
    javadocs/PTCommons-root/src/com/palantir/util/Mutable.java,
    javadocs/PTCommons-root/src/com/palantir/util/MultiMapSet.java,
    javadocs/PTCommons-root/src/com/palantir/util/MultiMapOrderedSet.java,
    javadocs/PTCommons-root/src/com/palantir/util/MultiMapList.java,
    javadocs/PTCommons-root/src/com/palantir/util/MultiMapConcurrentHashSet.java,
    javadocs/PTCommons-root/src/com/palantir/util/MultiMap.java,
    javadocs/PTCommons-root/src/com/palantir/util/i18n/DefaultDateFormatterFactory.java,
    javadocs/PTCommons-root/src/com/palantir/util/i18n/DateFormatterManager.java,
    javadocs/PTCommons-root/src/com/palantir/util/i18n/DateFormatterFactory.java,
    javadocs/PTCommons-root/src/com/palantir/util/i18n/DateFormatter.java,
    javadocs/PTCommons-root/src/com/palantir/util/awt/Awt.java"
    The first two gen properly with only one of each class showing up in the class list. Then, starting with the PTCommons files, javadoc lists each class twice in the class list. In the actual generated documentation, there is only one instance of the file.
    Has anyone seen this before?
    Mary

    Im having a problem with the variables.
    Part of my original problem might be each pxi was in a different project. and i had two projects each its own IP. Using this method i did not know how use two differnt variables from two differnet pxi' s with the same program.
    if your still following.
    i tried a simpler way
    i modified my project to include both ip addresses. 
    this way In my window environment my vi calls the variable. i made sure that i right clicked and chose the variables from the correct ip.
    what i have is two status indicators and two update buttons.
    the status tells me what stage the test is in
    the update button is for the user at the end of the test he can update the screen with the results.
    currently only my second pxi is updating status and also the update works
    this is my windows vi alias file
    [My Computer]
    My Computer=localhost
    [S4000xH-System1]
    S4000xH-System1=192.168.110.10
    [S4000xH-System2]
    S4000xH-System2=192.168.110.3
    do i need to bind to source or use the single writer. im going to try to undo the single writer seems like this would could onluy better it but doesnt seem like its for my application.
     i forgot to mention that the varibles i use  were there listed as dependancies for the windows evirment have a blue question mark  but show what is wrong.  
    where i have the variables under the ip address there are no blue question marks

  • Problem with a fusion of two companies

    Hi,
    Maybe somebody can help me with my problem with implementing FICO modules in two companies which are soon going to become one company. The fusion will probably take place on 1st january, but it can be posponed as well.
    Everything is prepared to run the common mont-end closing procedures and common planning/budgeting for both companies from the 1st january.
    However, there is a great risk, that the fusion will be delayed.
    In that case I suppose it would be better to enter one separate budget for the leading company and upload the budget of the other company after the fusion takes place. These actions have influence on calculating the manufacturing cost of products. It will certainly be different before and after the fusion.
    Maybe you can advise me on this subject, wheter I should make a common budget for both companies no matter the date of fusion or make a buget in SAP only for the leading company and upload the budget of the other company after the fusion, and then recalculate the manufacturing cost of products.
    Best wishes,
    karol

    Hi,
    As of now the time frame is more than 7 months to the go live date of Jan 01st 2008. Definitely, you would have drawn up a project plan for executing this project.
    In my view if the project is on schedule, at this point of time we can still consider making a consolidated budget after fusion. And the project schedule should be monitored closely as the deadline is coming closer. However, if by Oct 01st 2007 the project is not on schedule and there is a likelihood of delay / postponement, the second option of having a separate budget for each company code can be considered.
    A contingency / back up should be prepared and this should be implemented if the original plan is not working out.
    Thanks
    Murali.

  • Problem with replicated partitioning between two BSO db's. version 9.3.0.1

    Hi there,
    I have a problem with partitioning between two BSO db’s.
    I created the partition, it validates and I made an export for the partion definiton(xml file).
    Everything is fine if I set this partition up as transparent partition.
    This means I can see the data from the src in the trg db as ecpected.
    But when I change over to replicated (what in fact I want to do) nothing happens for the trg site - there are still no data. (Yes I have choosen Update all cells.)
    I got no error in any way neither AAS nor in the app logs of src and trg.
    (Mayby this it important: one src-dimension is mapped to void for the trg.)
    Can anyone give me a hint or even confirm this behaviour ?
    Thank you in advance
    Andre
    Below the log infos:
    log of src db:
    [Fri Dec 04 15:29:03 2009]Local/AAA///Info(1013210)
    User [hyperion] set active on database [db]
    [Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1013091)
    Received Command [PutReplicatedCells] from user [hyperion]
    [Fri Dec 04 15:29:03 2009]Local/AAA///Info(1013210)
    User [hyperion] set active on database [db]
    [Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1013091)
    Received Command [XferReplicatedCells] from user [hyperion]
    [Fri Dec 04 15:29:03 2009]Local/AAA///Info(1013214)
    Clear Active on User [hyperion] Instance [1]
    [Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1023005)
    Update of replicated partition elapsed time : [0] seconds
    [Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1243010)
    Partition refreshed
    log of trg db:
    [Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013210)
    User [hyperion] set active on database [db]
    [Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1013091)
    Received Command [ReqXferReplicatedCells] from user [hyperion]
    [Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013210)
    User [hyperion] set active on database [db]
    [Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1013091)
    Received Command [ProtocolXchg] from user [hyperion]
    [Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1023044)
    Processing distributed request from [P4B5A856A, AAA, db]
    [Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1013091)
    Received Command [PutLastUpdatedTime] from user [hyperion]
    [Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013214)
    Clear Active on User [hyperion] Instance [1]
    [Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013214)
    Clear Active on User [hyperion] Instance [1]

    It sounds like you are doing it all correctly. One thing you might try just to be sure you are not getting any data in the target database is the following:
    1) clear the target database
    2) Run the replication for all cells
    3) Run an export of all data on the target database
    See if you get anything in the export file, maybe you are getting some of the data or possibly it is a rollup issue. Just a thought.
    Jeff

  • General install and deployment problem with WLS clustering on two boxes

    Hi,
    I've come across a general installation problem with WLS with a cluster spanning two different physical machines and two Managed Servers, one Managed Server per physical machine.
    The problem is, starting from scratch, you install WLS on both physical machines. You can then use the config wizard to create the domain, cluster and managed servers, but this is a manual typing in process.
    So we've now got a WLST Script which we run with "java weblogic.WLST domaincreate.py domain.properties". This is good as it creates the domain, cluster, managed servers and JMS modules.
    Now the trouble is, it doesn't do anything to the 2nd physical machine which will be running only the 2nd Managed Server.
    One dirty way to get around this in order to start the 2nd managed server was to copy the domain directory to the 2nd server, but I'm sure this is bad practice and what you can actually do is improve the WLST script to actually, but the same as the config wizard and dump the nessary information to the 2nd physical machine in order so you don't need to copy the domain directory across so that it will startup straight after running the WLST.
    Any help appriecated.
    Surfbum.

    Hi I think I've found the answer. You can build a managed server template using the pack command.
    http://e-docs.bea.com/common/docs90/pack/tasks.html

  • Problem With Fax Modem 43R1814 CallerID

    The Caller ID Doesn't Appear when I Use The Command AT+VCID=1 and the fax replies with OK. and when I use the Command AT#CID=1 The fax Replies with ERROR,any Ideas How to Read The Caller ID 

    Hi again,
    It's difficult for me to offer anymore than generalized advice but I'll try to be helpful.
    I'd start by removing the existing modem and restarting the computer.  One of the error messages mentioned PCI Slot 1.  This is probably the modem.  If ALL the error messages go away it's a pretty good indication that the modem is the problem and replacement is in order.  I would attempt simply re-seating the modem in it's slot first however and restarting.
    I'm pretty sure that the proper drivers would be found automatically for the existing modem.  If not, there's a rather generalized Readme file and a program called HXFSetup.exe which is probably the program you would need to run if required.
    While you're in the computer, disconnecting and reconnecting things might be better than just a visual inspection.  Twisting the cooling fan housing on the  CPU with moderate force shouldn't hurt anything and who knows?
    If it turns out that the modem is the problem (which I doubt), installing the other modem shouldn't be a problem, assuming it fits and you have the drivers for it.  Again, good luck.
    Jim
    P.S.  If you haven't already done so, Google all the error messages and see if there seems to be any common element.  There are diagnostic programs available on the web but I've never found one that helped me with a trouble, perhaps someone has and can make a recommendation.

  • CONSTANT problems with Airport Express in two rooms, dropped connection with gateway, no AirPlay

    I have 3 Airport Express in my apartment, one is connected (named Living Room) to my ISP provided gateway (router) and acts as the main wireless hub, the other two (named Kitchen and Bedroom) and are set up to provide AirPlay audio only.
    The ones set up for AirPlay have had constant issues since we moved to our new place 4 months ago, this is very strange because we were with the same ISP in the old place and used the same gateway (router) without any problems which leads me to think that there is something in the walls in the new place which is blocking an effective signal.
    Even as I type this, I have Airport Utility open on my Mac and a message just popped up from AU saying that 'Living Room is unavailable'.
    Attached is a screenshot which shows the current status of the Airport network. Basically it is a mess, and I have tried everything, from resetting the ISP router and all the AXPs, to changing the Network Modes to experimenting with repositioning the units to points in rooms where the reception might be better.
    NOTHING has made any difference.

    Sorry, have been away for work so only just had a chance to look again at this:
    I'lll try again: right now using WiFI Explorer I can see 9 other networks, 3 of those are using channel 11, the same as my Airport Express network. (Set to Automatic in Airport Utility)
    What I tried to explain earlier was that the one in the kitchen will not stay connected long enough for me to get a reading on WiFi Explorer, but I can tell you that I powered up the one in the bedroom at 19:56, it is currently connected in Extend Wireless Network mode (the one in the kitchen is disconnected from the power) and has an average SNR of 59dB (and shows as 'Excellent' in Airport Utility) and so far it has not dropped the connection, but I am 99% certain that it will be back to blinking amber by tomorrow.
    So there is one Airport Express in the living room which is the one that has created the wireless network, within the living room the Average SNR is around 60% (as you would expect as that is the unit that is wired to the ISP provided router).
    Since I connected the one in the bedroom earlier this evening it has managed to stay connected and appears to still be extending the network, I checked it just now by standing next to it with WiFi Explorer open on my MacBook Pro and it showed an average SNR of 55%.
    I ordered a 10 metre ethernet cable yesterday and I will try relocating the unit that is set to create the wireless network to a place in the living room that is closer to the bedroom and kitchen. It is currently on a shelf on the TV bank which is about two metres away from the wall closest to the kitchen.
    I will report back here once I have moved it and set up the kitchen and bedroom boxes again. Hopefully this will allow the kitchen one to stay connected long enough for me to get a reading on WiFi Explorer.

  • I need to migrate data from Lion to OSX do you know of any problems with content between the two systems?

    I'm using a MacBook AIR and OSX 10.9.1. When I upgraded that I made a mistake with the user name and so created another user. Now I understand I need to migrate the data between the two systems but that there might be trouble with some of the content files transferring across? Has anyone done this before? If so what were the pitfalls? Thanks and Help! No-one typing this feels as if they're on a steep learning curve at all!

    Hi nothpole
    Welcome to BlackBerry Support Forums
    Sorry to hear that you're having issues with your BlackBerry ! Before trying anything else can you try check a few setting or undo it on your device ?
    northpole wrote:
    I have memory cleaning scheduled to run every 1 hour.
    First advise is to disable Memory Cleaner ! you don't need that , It can cause freezing and clocking. To disable it , From your homescreen go to Options > Security > Advance Security setting > Memory Cleaner > Disable that feature .After disabling it reboot your device do it by removing the Battery while your device is Powered On then wait for at least a minute then reinsert it back, your device may take a long reboot . 
    Then monitor your device for the next few hrs. and check if you feel the same problem .
    let us know.
    Click " Like " if you want to Thank someone.
    If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

  • Problem with fax

    hou can i send  a fax from with in abap/4 programs

    check this link you will get a idea.
    sending report result by fax
    http://www.sap-img.com/abap/sending-fax-from-abap.htm
    regds,
    kiran

  • Have problem with Fax in AS5400HPX Voice Gateway

    I've problem in my system.AS5400 Voicegateway.when I send fax from my system,it's ok.But when i receive fax from another number in out system,data in fax loss.about 1/2 data in paper loss.
    -from my system to outside :ok
    -from outside to my system: not good
    please help me

    Hi,
    FYI, you can see the file configuration of AS5400. Please detect this issue to correct for my customers as soon as you can.
    Thanks
    Vo.

  • Problem with same application under two different context root

    JDev 11.1.1.6
    Does anyone have experience with such one scenario, so same app, but with two diff context root ?
    At a certain point, since both start to be used (and just in that case), at times there was a drastic deceleration, as if something is blocking some period. Subsequently, after some time, the application start to behave normally. I also periodically comes to acceleration and deceleration. In the log files there is no trace, no exception happens, nothing.
    And all this in a situation where both applications use only one user per app (so, the resources are not concerned)
    Any comments ?

    same app, but with two diff context root ?
    A web app packaged in WAR can have only one context root. Package a web app in two different WARs for two different context roots.
      weabpp1.war web.xml
    <?xml version='1.0' encoding='UTF-8'?>
    <weblogic-web-app>
      <context-root>context-1</context-root>
    </weblogic-web-app>
      weabpp2.war web.xml
    <?xml version='1.0' encoding='UTF-8'?>
    <weblogic-web-app>
      <context-root>context-2</context-root>
    </weblogic-web-app>

Maybe you are looking for

  • Web page different from opening link in a new tab or new window from Google search results

    I had been using another browser for a few months because I did not want to lose the web pages I opened within Mozilla. I began using Mozilla again after saving off the web pages. I see that Google's web page pulls in search results as I type in keyw

  • How do I save with ilife preview in v. 10.0.2?

    Under -preferences-general- there is no longer an audio preview box. So I can´t open a saved song into another project...How do I solve this?

  • Data Migration of Excise Duty payables at initial upload

    Hi! Can any one tell me, how to upload initial Excise Duty payable in data migration procedure. for example if different excise duty payables like ED, CESS, SEC.CESS for normal goods and capital goods. thanks in advances. regs, ramesh b

  • Error 4.7.1 message exceeds size limit, but it doesnt

    I am receiving this error every time I try to send a message. The size of the message you are trying to send exceeds a temporary size limit of the server. The message was not sent; try to reduce the message size or wait some time and try again. The s

  • How do you script in Photoshop?

    I've asked everywhere but here. Please where is there an option to script in Photoshop. Im tryin gto make the hands on a clock go around, which I have the script for it, I just need to use it in Photoshop. Somebody please direct me or help me.