Problem with Flip on MXF files...anyone?

Hello,
I am using PPro CS3 3.1 update that support the MXF files from Panasonic. We shoot with a 35mm Adapter and thus all our footage is recorded upside down. When we apply a horizontal flip and then a vertical flip, we get a flickering line on the top of the footage. It appears the the vertical flip is the culprit. Anyone else experiencing this with MXF files?

I would get that same thing on stills with motion. Sometimes I would use the crop filter with a crop of one pixel. Sometimes it would work and sometimes it wouldn't.

Similar Messages

Problem with Append mode in File Receiver

Hello,
I am facing some problem with Append Mode in File Receiver.
In channel config, i have given :
Construction Mode : Append
File Type : Text
Message Protocol : File Content Conversion
The size of the file which i am trying to send is about 9.5MB.
I got this error,
"Recovering from loss of connection to database; message
loaded into queue by recover job: System Job (Failover Recovery)".
So, it would seem that there was a loss of connnection to the database
while the file was being written.
Note - XI successfully recovered from the connection loss and
successfully wrote the file, however since the communication channel
was set to append, it appended to the partial file that was written
before the database connection loss. This is not correct. The file
should have been overwritten after the recovery even though the communication
channel was configured to append.
Can anyone help me on this regard.
Thanks,
Soorya.

Hi Venkat,
I would suggest u to split the file in to chunks if u face any problem in processing at a time in append mode and also
Memory Requirements are must 4 processing huge files:
Q: Which memory requirements does the File Adapter have? Is there a restriction on the maximum file size it can process?
A: The maximum file size that can be processed by the File Adapter depends on a number of factors:
o The most important one is the size of the Java heap, which is shared among all messages processed at a certain point in time. In order to be able to process larger messages without an out of memory error (OOM), it is recommended to increase the size of the available Java heap and/or to reduce the concurrency in the system so that fewer messages are processed in parallel.
o Another factor negatively influencing the maximum message size in releases up to and including XI 3.0 SP 13 is an enabled charcter set (encoding) conversion if the message type is set to "Text".
o Using the transport protocol "File Transfer Protocol (FTP)" also uses more memory for processing than the transport protocol "File System (NFS)" (up to and including XI 3.0 SP 13).
o If the Message Protocol "File Content Conversion" is used in a File Sender channel, consider that not only the size of the input file affects the File Adapter's memory usage, but even more the size of the XML resulting from the conversion, which is usually a few factors larger than the original plain text file.
To reduce the memory consumption in this scenario, consider configuring the setting "Maximum Recordsets per Message" for the sender channel. This will cause the input file to be split into multiple smaller mesages.
Plz do refer the following links:
U may plan the availability of ur communication channel using "Planning Availability Times" feature
http://help.sap.com/saphelp_nw04/helpdata/en/45/06bd029da31122e10000000a11466f/frameset.htm
/people/sravya.talanki2/blog/2005/11/29/night-mare-processing-huge-files-in-sap-xi
hi check the below links for reference
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/10748ef7-b2f0-2910-7cb8-c81e7f284af5
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/7086f109-aaa7-2a10-0cb5-f69bd2affd2b
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/2498bf90-0201-0010-4884-83568752a857
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/cc1ec146-0a01-0010-90a9-b1df1d2f346f
Regards,
Vinod.

Problem with Preview and PSD files - random gray square

Hi guys, hope you can help...
I've got a problem with Preview and PSD files.
If I open in Preview both an original jpg straight from my reflex and the photoshop version of the same picture, the psd file presents a gray square (of what it seems unrendered image) in a random area of the photo (sometimes in the center.). The square is quite big...
If I zoom in or zoom out it disappears...if I scroll to another photo and then back to the psd, the square it's there again...sometimes in a different position.
I've tried the same psd on my older iMac with leopard...and got no problem at all.
I suspect it got something to do with my Ati...
(this is the second iMac 27...the first went back for gray banding on the lcd screen and flickering and yellow tinge........)
Thanks for your help.
DAve.

maybe I'm onto something...
I've just found out that opening Preview in 32bit mode (instead of default 64bit) works flawlessly with any psd files. If I switch back to 64bit mode, Preview is much faster but the gray square comes back...
It seems like the i7 is much faster than the Ati....
Any more realistic ideas?

I have problems with seeing my bookmarks, file, view, edit...buttons. I tried other shortcuts. I noticed that all of my bookmarks are located in the Internet Explorer browsers, how can I restore setting back to Mozilla Firefox?

I have problems with seeing my bookmarks, file, view, edit...buttons. I tried other shortcuts. I noticed that all of my bookmarks are located in the Internet Explorer browsers, how can I restore setting back to Mozilla Firefox?

Is the menu bar missing (the one containing File, View, Edit etc)? If it is, the following link shows how to restore it - https://support.mozilla.com/kb/Menu+bar+is+missing

I have a problem with running an EXE file on win2000, the Lab View is 5.1 and I do not know if it is 16 bit...

I have a problem with running an EXE file on win2000, the Lab View is 5.1 and I do not know if it is 16 bit...what should I do?

Hi Arika,
The drivers that you need to install to make your executable work depends on what your executable is doing. To get started, you need to have the LabVIEW Run-Time Engine installed on your target machine (the Win2000 machine you are planning to use) in order to run your executable. Next, you need to determine what drivers your executable uses, if any. For example, if you are using GPIB instrument control, you will need to install the NI-488 drivers on your target machine. If you are performing data acquisition, you will need to install NI-DAQ drivers. If you are doing image acquistion, you will need to install NI-IMAQ drivers.
All these drivers are available for downloading on ni.com. To get the drivers, go to ht
tp://www.ni.com/support , click on the link that takes you to Drivers and Updates (under Option 3), and click on the links to get to the driver(s) you need. For example, if you need the LabVIEW 5.1.1 Run-Time engine, click on the All Drivers and Updates by Application link on the main page (http://www.ni.com/softlib.nsf/). Then click on the LabVIEW link, Windows 2000, Run Time Engine, and then you will see the link to get to the page to download the LabVIEW 5.1.1 Run-Time Engine.
I hope this information helps.
Best Regards,
Wilbur Shen
National Instruments

Problem with saving a pdf file to computer. Continually get an error message " This document could not be saved. There was a problem reading this document (21).

Need advice on a saving file issue. I'm having problem with saving a .pdf file to computer. Continually get an error message " This document could not be saved. There was a problem reading this document (21). This is new as this error message just recently started to pop-up.

More information about this issue can be found here:
https://forums.adobe.com/thread/1672655
A "quick" fix that worked for me was to uninstall Adobe... then download the base install for Adobe Reader 11.0.
Then download each of the individual updates and run them sequentially.
I've installed back up to the last security update which is version 08 and have been able to do normal Save As operations.
You will have to disable automatic updates in order to stay at version 08 until Adobe resolves this issue in a later release.
http://www.adobe.com/support/downloads/product.jsp?product=10&platform=Windows
Adobe Reader 11.0 - Multilingual (MUI) installer    AdbeRdr11000_mui_Std
Adobe Reader 11.0.01 update - Multilingual (MUI) installer    AdbeRdrUpd11001_MUI.msp
Adobe Reader 11.0.02 update - All languages    AdbeRdrSecUpd11002.msp
Adobe Reader 11.0.03 update - Multilingual (MUI) installer    AdbeRdrUpd11003_MUI.msp
Adobe Reader 11.0.04 update - Multilingual (MUI) installer    AdbeRdrUpd11004_MUI.msp
Adobe Reader 11.0.05 security update - All languages    AdbeRdrSecUpd11005.msp
Adobe Reader 11.0.06 update - Multilingual (MUI) installer    AdbeRdrUpd11006_MUI.msp
Adobe Reader 11.0.07 update - Multilingual (MUI) installer    AdbeRdrUpd11007_MUI.msp
Adobe Reader 11.0.08 security update - All languages    AdbeRdrSecUpd11008.msp

Problem with RTPExport output video files

Hi, I have a problem with RTPExport output video files. One side streams H263/RTP(AVTransmit2.java) and other write this steam to a file by RTPExport.java. When network conditions are ideal, output video file has same fps and same number of frames like original file. Problem occures, when theres packet lost in network, then output file has different fps,and also has less frames like original video(because it didnt write missing frames to file, and thats why it get shorter). Pls how can I achieve output file that will have the same fps like original one? How to write to file an identical copy of what I can see while receiveing video with AVReceive2.java? Its there a way to modifi rtpexport or avreceiver to do this? Thanks a lot!

Trubka wrote:
When network conditions are ideal, output video file has same fps and same number of frames like original file. Problem occures, when theres packet lost in network, then output file has different fps,and also has less frames like original video(because it didnt write missing frames to file, and thats why it get shorter). Okay, first off, the second file is smaller on purpose. RTP intentionally drops packets that are old/out of order in order to make sure real-time video stays as close to real time as it can. This is by design, so there's really nothing that can be done about it.
How to write to file an identical copy of what I can see while receiveing video with AVReceive2.java? Technically speaking, what you're getting in the RTPExport is exactly what you got on the receiving end. Any frames that are dropped during transmission will not be seen by the receiver, nor saved by the receiver.
Pls how can I achieve output file that will have the same fps like original one? I'm not 100% sure that you can, but, you can give the following idea a try. I make no guarentees that it'll work, but it should work for you...
[http://java.sun.com/javase/technologies/desktop/media/jmf/2.1.1/solutions/RTPConnector.html]
That example is an example of a "custom transport layer" for RTP connections. Essentially, it's some code that's handed the RTP packets on the transmission end, and it's expected to deliver those RTP packets on the other end. And it doesn't care about how they get from A to B, only that they do.
If you were to replace the UDP socket in that example with a TCP socket, you would be guarenteed not to drop packets due to network reasons. Every RTP packet you were handed by the transmitter, you would then hand to the receiver. There is no guarentee that none of the packets would be cast away as "old" by the RTP protocol itself, but there's also no guarentee any of them would be. It's a crap-shoot at best, but it's certainly worth a try.

A problem with importing layered PSD file into Flash

Hi.
There's a problem with importing layered PSD file into Flash.
If I import a layered PSD file, some part the color of the lower layer is shown at the edge of objects or shadows. Instead, if I crop each layers first and import them, there's no problem.
If the higher layer has brush or transparent effects, it becomes worse.
Any help with this problem?
Thanks.

How was the original art created? Was the original RGB or CMYK? What is the resolution of the Photoshop file? Flash only works well with RGB and 72 pixel per inch resolution. If your original art is not set this way, then Flash will attempt to convert it as it imports it. Flash uses the sRGB color space. You'll get the best color translation if your Photoshop file is using this color preference.

Problem with Snow Leopard and file sharing

I mostly work at home where I have an 18 months-old intel iMac 24'' running Leopard and an older iMac G5 20'' (PowerPC) running Tiger. Besides, I have a three months-old MacBook Pro 17" in which I recently upgraded the system to Snow Leopard.
Before this upgrade I never had a problem with the sharing of files between the three computers (I have them connected via Ethernet and a 5-port D-Link router wich provides flawless internet connection to the three computers). However, after the upgrade it has become impossible to connect the MacBook to the iMac G5 or vice versa via afp. Besides, getting the MacBook to connect to the (Leopard) iMac 24'' is frustratingly slow in either direction.
A related problem is the fact that after the upgrade the portable is no longer capable of seeing directly my ethernet-connected laser printer (to one of the ports of the D-Link router) although... surprise! it does see it as a shared printer in the iMac G5 and this way it prints alright.
Any ideas or suggestions to explore the cause of or solve this problem are warmly welcome.
Emilio Faro

Same problem here, did you find a solution?

Problems with mp4 (h.264) files, colour desaturated.

Hey guys. I've been having problems with mp4 h.264 files (not quicktime h.264). When playback on windows media player and windows classic media player it looks terrible. the saturation are weird (espesially on colours like yellow and red) and there seems to be this weird blur on the image. For so long I thought there was problem with the export from Premiere Pro, today however when playback on Quicktime player or VLC player it matches the orginal. I exported the file through premiere pro. I don't know what the problem is, maybe it's just the playback on windows media player and window classic media player.
Playback on quicktime
Playback on media player
Can someone tell me what's going on?

When playback on windows media player and windows classic media player it looks terrible. the saturation are weird (espesially on colours like yellow and red) and there seems to be this weird blur on the image... when playback on Quicktime player or VLC player it matches the orginal...
On the contrary, with more than high probability playback in QuirkTime shows you wrong colours because of its crooked colour management.
How do you judge on colour matching between your source file and what you see in media players?
What is your spec and GPU in particular? Do you use any sort of colour management in its settings?

HT204382 Hi, Ive just got myself a Macbook Pro, and Im having problems with sound on movie files. The format is wmv and they play OK on a windows 7 laptop, and Im trying to play them now on the MAC. The picture is OK , but no sound. I have Flip4Mac - no d

Hi, Ive just got myself a Macbook Pro, and Im having problems with sound on movie files. The format is wmv and they play OK on a windows 7 laptop, and Im trying to play them now on the MAC. The picture is OK , but no sound. I have Flip4Mac - no diference

Download and install the free VLC for Mac - that should work:
http://www.videolan.org/vlc/download-macosx.html

I've switched from Google to Firefox because I was so tired of Google crashed all the time. Now I have the same problem with Firefox, Bank id, file down

Hej!
I've switched from Google to Firefox because I was so tired of Google crashed all the time. Now I have the same problem with Firefox, Bank id, file downloading, accessing Web pages, none of it works. What is the error?
Ronnie.

When Firefox crashes, it usually records information about what was happening at that moment and displays the Mozilla Crash Reporter. Are you seeing that, or is Firefox just freezing and you're killing it?
Assuming you have crashes, you can submit that data to Mozilla and share it with forum volunteers to see whether it points to the solution. Please check the support article "[[Firefox Crashes]]" (especially the last section) for steps to get those crash report IDs, and then post some of the recent ones here.
If that's not possible, have you tried Firefox's Safe Mode? That's a standard diagnostic tool to deactivate extensions and some advanced features of Firefox. More info: [[Troubleshoot Firefox issues using Safe Mode]].
You can restart Firefox in Safe Mode using either:
* "3-bar" menu button > "?" button > Restart with Add-ons Disabled
* Help menu > Restart with Add-ons Disabled
Not all add-ons are disabled: Flash and other plugins still run
After Firefox shuts down, a small dialog should appear. Click "Start in Safe Mode" (''not'' Reset).
Any difference?

Problems reconnecting media with Canon C300 MXF files

Working from Canon C300 MXF files imported into up to date premiere cc (not sure if through the media browser or through the import function). We have three stations working (one AE station and two edit bays) but only two stores of the media so we've been backing up the media onto a third drive so our other editor can work. No problems with the first editor station and AE station, they both have all the media. Our third station however...
Basically the issue we're having is certain files won't reconnect to their MXFs, even though we've maintained the file structure and all associate canon files in their folders. We're getting diagonal shading across the clips in the timeline as well as the little triangle in the corner of the clip that signifies it's the end (and sometimes beginning) of the media. When we try to play those clips they are just a black screen. But when we try to match frame, it'll bring up the clip in the viewer and play fine. The media is not technically "offline," just not playing. When I try to reconnect the media I have to make it offline first and then reconnect but continue to have the same problem. It seems like an issue with merging the spanned clip across multiple .mxf files because there's no issue with clips that are not spanned. I tried isolating the individual clips from the .xml files that tell premiere to merge them and they reconnect fine up until the end of that file and then I've got diagonal lines for the rest of the clip again. I've tried everything I can think of and we're wasting so much money on this second editor not being able to work on anything because of this. Any insight would be most appreciated.

Ah I see, I read through your link, I get that reverting could help except that all our other stations are running 7.2.2 so we'd have incongruity between stations. Whats strange is the other two stations are running fine, no problems. It's just with this other station that doesn't have all the media that's having the issue.

Problems with Ericsson F3507g card - does anyone understand Access Connections log files?

I am having big problems getting an f3507g mobile broadband card working on a T500 running XP Pro.
Have had problems with several machines all supplied in the same batch and it turns out that the BIOS needs to be reset to defaults post installation of the card for it to be properly recognised by the OS.
Anyway, all machines are now fixed with the exception of one....
Everything looks okay on the surface - the F3507g card is showing under Device Manager, just to be sure I've reinstalled Access Connections and loaded drivers for the card. I know that the driver install was successful because it pinged up with the standard driver install success message - 'Windows found new hardware...' about half a dozen times immediately following the install. Having done the driver install I attempted connection and the CA Internet Security Suite Firewall popped up asking whether I wanted to accept the device as a 'Safe' device - clicked yes to that.
However, attempting connection never works
I've tried enabling logging and the log file produced together with a fault report is here.
I have tried the SIM card under test in another machine and it works. I have also swapped the HDD out of another identical brand new machine and it works with the hardware including the Ericsson card - so the issue has to be software related...
I could reimage but the user will loose some graphic design application software which is very difficult to reinstall.
Hope someone that understands Access Connections WWAN debug log files or has had a similar experience might be able to point me in the right direction...
Many thanks

@ Deadloss,
have you checked the power settings in the cards properties? Not that windows is turning it off?
Are you using a factory image or your own custom image, I'm thinking that maybe a reimage might help ??
@ schm1tty,
T-Mobile SIMs work fine, what problems are you having? Maybe you could start a new thread so as not to hijack this one.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Very frustrating problem with Photoshop Elements 10 - can anyone help?

I don't know what's happened, and I haven't changed any of the settings or anything.
When I open a photoshop file I am currently working on, now, no matter what I do, nothing changes in the actual photo. Even when I delete layers to see if it reverts back to the original photo, nothing changes. When I try adding new layers, nothing happens, when I try adjusting something such as opacity, or brightness/saturation, nothing changes.
I've tried opening/creating other photoshop files and I have the same problem, so it seems a problem with the actual software, rather than individual files. Even after uninstalling then installing the software, the problem is still there.
Does anyone have any idea what is causing this? Or could you direct me to a good help forum/source?
Many thanks

Welcome to the forum.
I would go to the Photoshop Elements Forum, and look for Loraclf's post there, or post with your problem, your equipment info, and the problem. Someone there will be able to help you.
Good luck,
Hunt

Problem with Flip on MXF files...anyone?

Similar Messages

Maybe you are looking for