Problem with H323 gateway
We have a CUCM ver 8.6.2.22900-9.
For our PSTN access we have the following scheme:
CUCM <========> Cisco2911 <======> ISP-------> PSTN
H323 tk SIP tk
Our Cisco2911 is running ver 150-1.M4.
We configure Cisco 2911 as H323 gateway on CUCM, and we established a SIP tk with our ISP.
When we tested incoming calls we received them at router but they are unable to acceess CUCM,
When we tested outgoing calls we got reorder tone and they did not reach our voice gateway.
We run "debug cch323 all" and tested with one incoming and one outgoing call, and we got the out on attached file "debug h323 forum"
CUCM Ip : 10.1.2.2
Router's H323 int: 10.2.2.1
Do you have any idea about the root cause?
Can be an access list problem preventing proper H323 traffic??
Thanks in advanced
Enrique
Do you have voip dial-peers pointing back to your cucm from your gateway? If not then the call wouldn't route onward to the cucm, but the gateway would also ignore communications from that souce because of toll fraud prevention.
http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/112083-tollfraud-ios.html
Similar Messages
-
Codec problem with one gateway
I am having a very strange problem with one of my gateways. No matter how I set up my regions and device pools I continue to have all calls go through this gateway as G729. This would be fine except that I can't do conference calls because of codec mismatches.
The gateway is a PRI running H323. CM 3.2.2(c) Gateway is a 3640 running 12.2.11(t)
All regions are currently set to G711.
I read something about a command under voice-port that sets the default codec. What I don't understand is, if this is what is causing it to go to G729, why is this the only gateway that ignores the regions.
Any help would be appreciated.Cisco VoIP gateways support the codec negotiation feature. This feature provides the ability for a Cisco VoIP gateway to connect to other VoIP devices without necessarily knowing which codec is used for a call-setup. Also, this feature allows Cisco VoIP gateways to dynamically adjust to changes on remote devices. As long as the codec used by the remote VoIP device matches the capabilities-list of the Cisco VoIP gateway, the VoIP call is completed.
The following example shows how to configure codec negotiation:
Cisco-router# config t
Cisco-router(config)# voice class codec 1
!--- This sets up class 1 to be assigned to the dial peer.
Cisco-router(config-class)#codec preference 1 g723r63
Cisco-router(config-class)#codec preference 2 g729ar8
Cisco-router(config-class)#codec preference 3 g711ulaw
Cisco-router(config-class)#codec preference 4 g726r32 bytes 240
!--- These commands define the preferred codec list using 1,2,3, and 4 to set the preference.
Cisco-router(config)#dial-peer voice 1 voip
Cisco-router(config-dial-peer)#voice-class codec 1
!--- This assigns voice-class codec 1 to the dial-peer
Cisco-router(config-dial-peer)#destination-pattern 4723155
Cisco-router(config-dial-peer)#session target ipv4:192.168.100.1 -
Problem with RD gateway manager
Hi,
Have some problems with manager. It used to work, but suddenly I can't connect to local server.
Get this error:
"The RD Gateway Managment snap-in console cannot connect to the server. To connect to this server, you must be a memeber of the local administrators group on the server."
The user account that i'm using is a member of the local administrator group.
Any ideas?
The RDS server is a Win2012 server. The AD server is a win 2008 R2 server.
Thanks
\KentHi Kent,
Thanks for your comment.
For this you need to create RD Rap and RD CAP policies. When you create the RD RAP, add the user groups that you defined in the RD CAP. Also, create a new RD Gateway-managed computer group that contains both the NetBIOS names and the fully qualified domain
names (FQDNs) of the RD Session Host servers or the RD Session Host server farm that hosts the RemoteApp programs.
Please check below article for information.
1. Remote Desktop Gateway Manager
2.How To Work with RD Gateway in Windows Server 2012
Hope it helps!
Thanks.
Dharmesh Solanki -
Problem with Mobile Gateway 1.0 Configuration
reffering to the config guide for mobile gateway 1.0 (https://websmp102.sap-ag.de/~sapdownload/011000358700000518422009E/Config_Guide_MGW_SP01_rev.pdf) we are facing some problems with the configuration in the DOE.
In Chapter 4.1.1.4 a SWCV "MAS_SMARTPHONE" is mentioned, which is not available in our System, though all other steps before have been successfully executed.
We are on SP08 and SWCV "SAP BASIS 7.10" is activated and generated.
Does anyone know a workaround?
Thanks in advancei think i located the problem in the DOE.
When a new device is registered (by user-login from device) some LUW's are listed in the SMQ2 for that Queue. Here several dumps occur:
--> 100 ABBTO RR014013005_DRFILLING_006 MMW_RR_RR014013005 05.11.2009 18:19:51 Syntax error in program
ZDOECL_013_005_STRWRPR==== 0A0A001710804AF2FB270034
0A0A001710804AF2FB270034 bgw23
--> 100 ABBTO RR014013002_DEPQ_SERVICE MMW_RR_RR014013002 05.11.2009 18:19:53 Syntax error in program
ZDOECL_013_002_STRWRPR==== 0A0A001710604AF2FB29000E
0A0A001710604AF2FB29000E bgw23
From ST22:
Error in the ABAP application program.
The current ABAP program "SAPLSMMW_STRWRAPPER_APIS" had to be interrupted
because it contains
a statement that cannot be executed.
In the include "ZDOECL_013_002_STRWRPR========CM001 " in the line 21 of program
"ZDOECL_013_002_STRWRPR========CP " the following syntax
errors occur:
"Field "INIT_FLAG" is unknown. It is neither in one of the specified ta"
"bles nor defined by a "DATA" statement. "DATA" statement." -
Problem with trasparent gateway versus Microsoft SqlServer.
Hi.
When I declare a cursor into PL-SQL procedure that select records from a SQL-SERVER table linked using a trasparent gateway.
I have two problem:
-1- I' m unable to update the linked table. I receve e timeout exception.
-2- whe I execute the second fatch operation I receve ad error : invalid cursor.
Trasparent gateway is configured as two_fase_commit.
Can Anyone help me?
Best regards.
VincenzoHallo
Yes I've tired ad it correctly work. But when I exit from cursor without make commit, and I run this simple update query (that works in sql/plus)
"update lsruni_ser@anaconda set "lsruni_ser_flag_elab" = 'Y' where "lsruni_ser_flag_elab" = 'Y';" I receve a timout messagge from SQL SERVER.
I HAVE GREAT PROBLEM WITH INSERT QUERY USED IN A PL-SQL PROCEDURE.
Thank You for support.
Vincenzo -
Problem with "Database Gateway for SQL Server"
Hello,
i am testing the different technologies for connecting an oracle database with a sql-server database.
The way using 10g-generic-connectivity with ODBC works fine, but the 11g-DG4MSQL makes problems.
Environment:
Server PEGASUS (32bit Windows Server 2003 R2 SP2) with Oracle Database 10g Release 10.2.0.4.0
Server OBELIXUS (32bit Windows 2000 Sp4) with MS-SQL-Server 2005
On PEGASUS i have installed the gateway in a new oracle home directory:
"D:\oracle\product\10.2.0\db_1" => home directory of 10g
"D:\oracle\product\11.1.0\tg_1\" => home directory of the gateway
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\tnsnames.ora:
MSSQLDG =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = DG4MSQL)
(HS = OK)
MSSQL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = MSSQLTEST)
(HS = OK)
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\listener.ora:
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = INTEGRAT)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_NAME = INTEGRAT)
(SID_DESC =
(SID_NAME = MSSQLTEST)
(PROGRAM = D:\oracle\product\10.2.0\db_1\bin\hsodbc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_DESC=
(SID_NAME=DG4MSQL)
(ORACLE_HOME=D:\oracle\product\11.1.0\tg_1)
(PROGRAM=D:\oracle\product\11.1.0\tg_1\BIN\dg4msql)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1521))
D:\oracle\product\11.1.0\tg_1\dg4msql\admin\initDG4MSQL.ora:
HS_FDS_CONNECT_INFO=OBELIXUS/MSSQLSERVER/testuju
HS_FDS_TRACE_LEVEL=DEBUG
HS_FDS_RECOVERY_ACCOUNT=RECOVER
HS_FDS_RECOVERY_PWD=RECOVER
D:\oracle\product\10.2.0\db_1\hs\admin\initMSSQLTEST.ora:
HS_FDS_CONNECT_INFO=DSN_MSSQL
HS_FDS_TRACE_LEVEL=OFF
HS_LANGUAGE=AMERICAN_AMERICA.WE8MSWIN1252
HS_FDS_FETCH_ROWS=100
HS_RPC_FETCH_REBLOCKING=OFF
How mentioned above, the access from oracle to sqlserver using MSSQL(10g hsodbc.exe) works fine.
But when trying to acces the sqlserver using MSSQLDG (11g dg4msql.exe) I get the following error:
ORA-28500: Verbindung von ORACLE zu Fremdsystem gab diese Nachricht zurück:
[Oracle][ODBC SQL Server Driver][DBNETLIB]Ungültige Verbindung.
[Oracle][ODBC SQL Server Driver][DBNETLIB]ConnectionOpen (ParseConnectParams()).
[Oracle][ODBC SQL Server Driver]Ungültiges Attribut für die Verbindungszeichenfolge
ORA-02063: vorherige 2 lines von DBL_MSSQL4
Here the contect of the file "DG4MSQL_agt_2332.trc":
Oracle Corporation --- FREITAG AUG 22 2008 16:17:42.198
Heterogeneous Agent Release
11.1.0.6.0
Oracle Corporation --- FREITAG AUG 22 2008 16:17:42.198
Version 11.1.0.6.0
Entered hgogprd
HOSGIP for "HS_FDS_TRACE_LEVEL" returned "DEBUG"
Entered hgosdip
setting HS_OPEN_CURSORS to default of 50
HOSGIP returned value of "RECOVER" for HS_FDS_RECOVERY_ACCOUNT
HOSGIP returned a value for HS_FDS_RECOVERY_PWD
setting HS_FDS_TRANSACTION_LOG to default of "HS_TRANSACTION_LOG"
setting HS_FDS_TRANSACTION_ISOLATION to default of "READ_COMMITTED"
setting HS_NLS_NCHAR to default of "AL16UTF16"
setting HS_FDS_TIMESTAMP_AS_DATE to default of "TRUE"
setting HS_RPC_FETCH_REBLOCKING to default of "ON"
setting HS_FDS_FETCH_ROWS to default of "100"
setting HS_FDS_RESULTSET_SUPPORT to default of "FALSE"
setting HS_FDS_PROC_IS_FUNC to default of "FALSE"
setting HS_FDS_CHARACTER_SEMANTICS to default of "FALSE"
setting HS_FDS_MAP_NCHAR to default of "TRUE"
setting HS_NLS_DATE_FORMAT to default of "YYYY-MM-DD HH24:MI:SS"
setting HS_FDS_REPORT_REAL_AS_DOUBLE to default of "FALSE"
setting HS_LONG_PIECE_TRANSFER_SIZE to default of "65536"
setting HS_SQL_HANDLE_STMT_REUSE to default of "FALSE"
setting HS_FDS_QUERY_DRIVER to default of "FALSE"
setting HS_CALL_NAME_ISP to "gtw$:SQLTables;gtw$:SQLColumns;gtw$:SQLPrimaryKeys;gtw$:SQLForeignKeys;gtw$:SQLProcedures;gtw$:SQLStatistics"
Exiting hgosdip, rc=0
ORACLE_SID is "DG4MSQL"
Product-Info:
Port Rls/Upd:6/0 PrdStat:0
Agent:Oracle Database Gateway for MSSQL
Facility:hsa
Class:MSSQL, ClassVsn:11.1.0.6.0_0006, Instance:DG4MSQL
Exiting hgogprd, rc=0
Entered hgoinit
HOCXU_COMP_CSET=1
HOCXU_DRV_CSET=178
HOCXU_DRV_NCHAR=2000
HOCXU_DB_CSET=178
HOCXU_SEM_VER=102000
Entered hgolofn at 2008/08/22-16:17:42
RC=-1 from HOSGIP for "PATH"
PATH from environment is "d:\oracle\product\11.1.0\tg_1\bin;D:\oracle\product\10.2.0\db_1\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Programme\IBM\Informix\Client-SDK\bin"
Exiting hgolofn, rc=0 at 2008/08/22-16:17:43
HOSGIP for "HS_OPEN_CURSORS" returned "50"
HOSGIP for "HS_FDS_FETCH_ROWS" returned "100"
HOSGIP for "HS_LONG_PIECE_TRANSFER_SIZE" returned "65536"
HOSGIP for "HS_NLS_NUMERIC_CHARACTER" returned ".,"
Exiting hgoinit, rc=0 at 2008/08/22-16:17:43
Entered hgolgon at 2008/08/22-16:17:43
reco:0, name:testuju, tflag:0
Entered hgosuec at 2008/08/22-16:17:43
uencoding=UTF16
Entered shgosuec at 2008/08/22-16:17:43
Exiting shgosuec, rc=0 at 2008/08/22-16:17:43
shgosuec() returned rc=0
Exiting hgosuec, rc=0 at 2008/08/22-16:17:43
HOSGIP for "HS_FDS_RECOVERY_ACCOUNT" returned "RECOVER"
HOSGIP for "HS_FDS_TRANSACTION_LOG" returned ""HS_TRANSACTION_LOG""
HOSGIP for "HS_FDS_TIMESTAMP_AS_DATE" returned "TRUE"
HOSGIP for "HS_FDS_CHARACTER_SEMANTICS" returned "FALSE"
HOSGIP for "HS_FDS_MAP_NCHAR" returned "TRUE"
HOSGIP for "HS_FDS_RESULT_SET_SUPPORT" returned "FALSE"
HOSGIP for "HS_FDS_PROC_IS_FUNC" returned "FALSE"
HOSGIP for "HS_FDS_REPORT_REAL_AS_DOUBLE" returned "FALSE"
using testuju as default value for "HS_FDS_DEFAULT_OWNER"
HOSGIP for "HS_SQL_HANDLE_STMT_REUSE" returned "FALSE"
Entered hgocont at 2008/08/22-16:17:43
HS_FDS_CONNECT_INFO = "OBELIXUS/MSSQLSERVER/testuju"
RC=-1 from HOSGIP for "HS_FDS_CONNECT_STRING"
Entered hgogenconstr at 2008/08/22-16:17:43
dsn:OBELIXUS/MSSQLSERVER/testuju, name:testuju
optn:
Entered shgogohn at 2008/08/22-16:17:43
ohn is 'OraGtw11g_home1'
Exiting shgogohn, rc=0 at 2008/08/22-16:17:43
Entered hgocont_OracleCsidToIANA at 2008/08/22-16:17:43
Returning 2252
Exiting hgocont_OracleCsidToIANA at 2008/08/22-16:17:43
##>Connect Parameters (len=223)<##
## DRIVER=Oracle 11g dg4msql-OraGtw11g_home1;
## SERVER=OBELIXUS\MSSQLSERVER;
## Database=testuju;
#! UID=testuju;
#! PWD=*
## AnsiNPW=Yes;
## QuotedId=Yes;
## IANAAppCodePage=2252;
## ArraySize=100;
## PadVarbinary=0;
## SupportNumericPrecisionGreaterThan38=1;
Exiting hgogenconstr, rc=0 at 2008/08/22-16:17:44
Entered hgopoer at 2008/08/22-16:18:00
hgopoer, line 159: got native error 14 and sqlstate 08001; message follows...
[Oracle][ODBC SQL Server Driver][DBNETLIB]Ungültige Verbindung.[Oracle][ODBC SQL Server Driver][DBNETLIB]ConnectionOpen (ParseConnectParams()).[Oracle][ODBC SQL Server Driver]Ungültiges Attribut für die Verbindungszeichenfolge
Exiting hgopoer, rc=0 at 2008/08/22-16:18:00
hgocont, line 1890: calling SqlDriverConnect got sqlstate 08001
Exiting hgocont, rc=28500 at 2008/08/22-16:18:00 with error ptr FILE:hgocont.c LINE:1910 ID:Something other than invalid authorization
Exiting hgolgon, rc=28500 at 2008/08/22-16:18:00 with error ptr FILE:hgolgon.c LINE:612 ID:Calling hgocont
Entered hgoexit at 2008/08/22-16:18:00
Exiting hgoexit, rc=0 at 2008/08/22-16:18:00
Many thanks in advance for any help!
Regards HartmutAt first your configuration is not really correct.
=====================================================
In the LISTENER.ORA from 10g, you must only refer to the database and hsodbc 10g
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\listener.ora:
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = INTEGRAT)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_NAME = INTEGRAT)
(SID_DESC =
(SID_NAME = MSSQLTEST)
(PROGRAM = D:\oracle\product\10.2.0\db_1\bin\hsodbc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1521))
===========================================================
Then you have to create a new listener (new name) in the gateway oracle_home on a different port than instance database:
D:\oracle\product\11.1.0\tg_1\network\admin\listener.ora
SID_LIST_LISTENERGTW =
(SID_LIST =
(SID_DESC=
(SID_NAME=DG4MSQL)
(ORACLE_HOME=D:\oracle\product\11.1.0\tg_1)
(PROGRAM=D:\oracle\product\11.1.0\tg_1\BIN\dg4msql)
LISTENERGTW=
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1522))
To start it, use the command below:
D:\oracle\product\11.1.0\tg_1\bin\LSNRCTL start listenergtw
===========================================================
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\tnsnames.ora:
match the DG4MSQL with the listener on 1522 port
HSODBC match with binary10g on listener 1521 port
MSSQLDG =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1522))
(CONNECT_DATA =(SERVICE_NAME = DG4MSQL))
(HS = OK)
MSSQL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =(SERVICE_NAME = MSSQLTEST))
(HS = OK)
Try to configure and let me know your feedback
regards,
Mireille -
Problem with my Gateway FX 6800-10e
Yes, lately ive been having problems that whne im playing on my PC ( normally is WoW) the computer turns off like it lost power, and then reboots again on its own, i havent found that is getting over heated, though were i live is really hot inside and i cant affor A/C 24/7 but ive checked the GPU temp and is under the normal temp. Ive heard around that it may be PSU problems. Im looking for opinions on what should i be looking for to fix the problem.
Operating System: Windows Vista™ Home Premium (6.0, Build 6002) Service Pack 2 (6002.vistasp2_gdr.091208-0542)
Language: English (Regional Setting: English)
System Manufacturer: Gateway
System Model: FX6800-01e
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz (8 CPUs), ~2.7GHz
Memory: 3062MB RAM
Card name: ATI Radeon HD 4850 Seriesthe driver for ati makes it so you can run the "windows Experiance Index" without crashing, this led me to think that it was solved, the computer still turns off all by its self and then restarts. there are tons of forum posts about people with this model updateing to windows 7 (great os on every other computer I have put it on) and having problems.
I have seen a Bios update which I have tried to do long distance, this is my grandfathers computer, there are some steps after update that I dont know if they were done right.
hope we find the solution, as of now I am responsable for getting my grandfather a big bright orange and black paper weight -
Problem with the gateway protection
a few days ago I successfully installed the router WRT54G2 for a wireless broadband connection and I set the wep protection. Today I was suggested to change the security WPA2: I opened the window EasyLink Advisor, I went to tools and then in the keys protection control menù (the icon is represented by 2 keys) and I changed the protection from wep to WPA2 ; after I clikked on forward I was no longer able to create a connection. After several attempts and configurations I created a wireless connection, but checking the details of the gateway, I noticed that the "Wireless Encryption" is written "none" therefore now I am afraid that is not protected. Checking the details of my connection the wireless connection is set on wpa2: is it normal that my connection is wpa2 protected and the gateway no?
I would reinstall everything using the cd that came with the router: How do I reset everything and make the reinstallation ends successfully without any problems?
thanksTo reset your router press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
To re-configure the router don't use the CD, instead :
If your ISP is Cable go here
If your ISP is DSL go here
To enable Security go here -
Problem with exclusive gateway in multi-instance subprocess
Hi,
I've recently developed a BPM process with 11gPS4 FP, the idea is simple:
1. The initiator select a set of "StakeHolders" from LDAP, each "StakeHolder" has an BOOLEAN attribute "isApprover"
2. There is a multi-instance subprocess, I used Parallel and Collection and I point the input & output array to the list selected in Initiator step
3. There is an exclusive gateway named "is approver or not" which have one unconditional sequence and one conditional sequence. In the conditional sequence I use the expression inputDataItem.isApprover == true which inputDataItem is a predefined object.
My intention is that when entering the subprocess, the stakeholders with "isApprover" is true should receive a task, but I found out that no matter "isApprover" is true or not, the expression will never become true. It always goes to the unconditional sequence. Then I tried to use some string attribute like inputDataItem.userID == "weblogic" and it works fine.
I've tried different expressions, like "inputDataItem.isApprover" or XPATH Expression but none of them work. I think it might be a bug that the gateway in a subprocess cannot use boolean type of attribute?
Has anyone met this problem before? Am I wrong somewhere or it's really a bug? Thank you in advance!At first your configuration is not really correct.
=====================================================
In the LISTENER.ORA from 10g, you must only refer to the database and hsodbc 10g
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\listener.ora:
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = INTEGRAT)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_NAME = INTEGRAT)
(SID_DESC =
(SID_NAME = MSSQLTEST)
(PROGRAM = D:\oracle\product\10.2.0\db_1\bin\hsodbc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1521))
===========================================================
Then you have to create a new listener (new name) in the gateway oracle_home on a different port than instance database:
D:\oracle\product\11.1.0\tg_1\network\admin\listener.ora
SID_LIST_LISTENERGTW =
(SID_LIST =
(SID_DESC=
(SID_NAME=DG4MSQL)
(ORACLE_HOME=D:\oracle\product\11.1.0\tg_1)
(PROGRAM=D:\oracle\product\11.1.0\tg_1\BIN\dg4msql)
LISTENERGTW=
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1522))
To start it, use the command below:
D:\oracle\product\11.1.0\tg_1\bin\LSNRCTL start listenergtw
===========================================================
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\tnsnames.ora:
match the DG4MSQL with the listener on 1522 port
HSODBC match with binary10g on listener 1521 port
MSSQLDG =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1522))
(CONNECT_DATA =(SERVICE_NAME = DG4MSQL))
(HS = OK)
MSSQL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =(SERVICE_NAME = MSSQLTEST))
(HS = OK)
Try to configure and let me know your feedback
regards,
Mireille -
Problem with Mobile Gateway 1.1 Configuration
Hello everyone,
During installation of Gateway 1.1 to SAP Netweaver Mobile(Mobile Sales), I met one problem about not retrieving Activity on device.
I've checked in SAP Netweaver Mobile administrator, the reason looks like that Activity data objects don't met with Distribution Rule Critieria, which is ET_ACTIVITY_H - USER_ID EQ abc. All my loaded Activity data objects contain empty value in USER_ID field.
So, does anyone know how to fix it?
Thanks in advance.I've searched in this forum and found Re: NetWeaver Mobile / Sybase. I also follow steps of "GW_11_SP01_CRM_Config_Guide.pdf", but the result is still what I provide in the first post.
I'm not familiar with CRM system, and guess that one way to resolve it is to insert one activity with USER_ID = abc into CRM system.
Does someone have any experience about this topic? -
Problems with XB3 gateway; it won't connect to internet properly in bridge mode
I recently moved to a new area and had to replace my old gateway from the other comcast franchise with a new one. The new one has built-in wifi. Ever since I got the new gateway, my connection has been slow and unreliable, especially when more than one person is trying to use a computer at once, and I do not like that this wifi is interfering with the setup I was previously happy with using my airport time capsule as a router, with my old airport express in bridge mode for airtunes use. In that setup with the same people and devices and use habits I did not have these problems. I looked for directions on how to disable the built-in wifi (I also don't like just putting out connections I do not use, it feels like a waste of my signal and a security risk!) and followed the instructions i found on this forum which seemed very simple. I logged in to the gateway and turned bridge mode on, restarted everything, switched the time capsule back OUT of bridge mode... and my time capsule and airport were all green, as well as the online login to the gateway saying it was connected to the internet, but my time capsule showed that there was no internet connection and in terms of loading web pages... deifnitely the time capsule was correct in that I was not getting a connection. My computers and devices weren't showing up on the gateway's page as "connected devices" either. I've tried multiple times, reset everything multiple times, and rechecked directions but for now I had to re-enable the wifi and suddenly i can get online again. (And no, it's not that my computer is actually using those netowrks - I'm on my Time Capsule's network and checking the status through the airport utility.) I really want to get this extra wifi disabled and see if that resolves my crappy connection problems because the service is just useless in the evening as it is now! If anyone knows what might be wrong, I'd appreciate the help. Everything should be on pretty standard settings as far as my Time Capsule and Airport go - Airport is just in client mode, TC has to be in bridge mode when the other wifi is on or I get errors, but i haven't done anything fancy with any of its settings.
Hi, since you have 2 Linksys devices and it's hard to pinpoint the exact problem. You might the try doing changes on both Linksys devices.
WRT54GX2
- update or reflash the firmware
- change the channel from auto to 11 or 1
- change the beacon interval value to 50
WMP54GX
- download and update to the latest drivers -
Problem with OSGD gateway 4.7
I have two SGD nodes in our network and I will use OSGD gateway to forward requests to the nodes. The nodes and the gateway are in the same subnet and currently it does not work.
I try it with self signed ssl and without. Without ssl I immediatly logout from OSGD and with SSL I got no response. I can see that certificates are in place and also the gateway.
Does it work out of the box or is it necessary to do some tricks (e.g. iptables) when all parts in the same network ?
Thanks in advance !Hello,
I found only /opt/SUNWsgdg/proxy/var/log and there is this :
SEVERE: config.xml.XMLConfigurationException: No gateway decryption key found in keystore
Here is some more information :
[root@vmhost1 log]# /opt/SUNWsgdg/bin/gateway config list
binding: *:80
routes-http-maxcon: 100
routes-aip-maxcon: 512
routes-reverseproxy-redirect: null
services-reflection-binding: localhost:81
services-reflection-auth-binding: *:82
[root@vmhost1 ~]# /opt/SUNWsgdg/bin/gateway server list
SGD Server: vmhost1
URL: http://vmhost1.bla.de
CA Certificate:
Owner: CN=vmhost1.bla.de CA Cert
Issuer: CN=vmhost1.bla.de CA Cert
Serial number: 86d0221e5335dfbc
Valid from: Wed Jul 24 12:43:01 CEST 2013 until: Sat Jul 22 12:43:01 CEST 2023
SGD Server: vmhost2
URL: http://vmhost2.bla.de
CA Certificate:
Owner: CN=vmhost2.bla.de CA Cert
Issuer: CN=vmhost2.bla.de CA Cert
Serial number: dbb839eaaa53ebf6
Valid from: Wed Jul 24 12:43:25 CEST 2013 until: Sat Jul 22 12:43:25 CEST 2023
[root@vmhost1 log]# /opt/tarantella/bin/tarantella gateway list
Installed gateway: osgd-gateway
Issuer: CN=vmhost1.bla.de
Serial Number: 1375094907
Subject: CN=vmhost1.bla.de
Valid from Mon Jul 29 12:48:27 CEST 2013 to Wed Jun 07 12:48:27 CEST 2023 -
I am trying to use the socket gateway to watch a port 1010
for all incoming data. When data comes in I want to log it. Well to
get started I just used a simple example from the docs to see if I
could get it to work. But when I try to start the gateway I get
this error:
SocketGateway(tvsocket) Error opening port 1010:
java.net.BindException: Address already in use: JVM_Bind
Does anyone know what that means?
jfillIt could mean just what it says. The port is already in use
by some other application. On Windows, you can verify that using
FPort. -
Problem with my Gateway laptop that I brought...
in Best Buy. I brought a MT6840.
The monitor has a horizontal line across the lower part of the taskbar. I want to know how I can fix this problem.The screen behavior you post about here indicates a possible hardware failure that is about to get worse. You can try and update your video card driver , but in the end, it very well might not be curing that line in your screen. I wish I could give you better advice , but since I am not in front of your particular machine its very hard for me to diagnose the problem in a more accurate manner.
*******DISCLAIMER********
I am not an employee of BBY in any shape or form. All information presented in my replies or postings is my own opinion. It is up to you , the end user to determine the ultimate validity of any information presented on these forums. -
RD Gateway 2012 R2 (DMZ) - Problem with authentification (NULL SID)
Hello,
I have a problem with a RD Gateway 2012 R2, that domain users can't log on over the RD Gateway to the RD Sessionhost. I get an error message in the eventlog on the RD Gateway.
Protokollname: Security
Quelle: Microsoft-Windows-Security-Auditing
Datum: 09.12.2014 16:45:24
Ereignis-ID: 4625
Aufgabenkategorie:Anmelden
Ebene: Informationen
Schlüsselwörter:Überwachung gescheitert
Benutzer: Nicht zutreffend
Computer: DMZ2.bptest.local
Beschreibung:
Fehler beim Anmelden eines Kontos.
Antragsteller:
Sicherheits-ID: NULL SID
Kontoname: -
Kontodomäne: -
Anmelde-ID: 0x0
Anmeldetyp: 3
Konto, für das die Anmeldung fehlgeschlagen ist:
Sicherheits-ID: NULL SID
Kontoname: [email protected]
Kontodomäne:
Fehlerinformationen:
Fehlerursache: Bei der Anmeldung ist ein Fehler aufgetreten.
Status: 0xC000005E
Unterstatus:: 0x0
Prozessinformationen:
Aufrufprozess-ID: 0x0
Aufrufprozessname: -
Netzwerkinformationen:
Arbeitsstationsname: SCHULUNG
Quellnetzwerkadresse: -
Quellport: -
Detaillierte Authentifizierungsinformationen:
Anmeldeprozess: NtLmSsp
Authentifizierungspaket: NTLM
Übertragene Dienste: -
Paketname (nur NTLM): -
Schlüssellänge: 0
Dieses Ereignis wird beim Erstellen einer Anmeldesitzung generiert. Es wird auf dem Computer generiert, auf den zugegriffen wurde.
Die Antragstellerfelder geben das Konto auf dem lokalen System an, von dem die Anmeldung angefordert wurde. Dies ist meistens ein Dienst wie der Serverdienst oder ein lokaler Prozess wie "Winlogon.exe" oder "Services.exe".
Das Anmeldetypfeld gibt den jeweiligen Anmeldetyp an. Die häufigsten Typen sind 2 (interaktiv) und 3 (Netzwerk).
Die Felder für die Prozessinformationen geben den Prozess und das Konto an, für die die Anmeldung angefordert wurde.
Die Netzwerkfelder geben die Quelle einer Remoteanmeldeanforderung an. Der Arbeitsstationsname ist nicht immer verfügbar und kann in manchen Fällen leer bleiben.
Die Felder für die Authentifizierungsinformationen enthalten detaillierte Informationen zu dieser speziellen Anmeldeanforderung.
- Die übertragenen Dienste geben an, welche Zwischendienste an der Anmeldeanforderung beteiligt waren.
- Der Paketname gibt das in den NTLM-Protokollen verwendete Unterprotokoll an.
- Die Schlüssellänge gibt die Länge des generierten Sitzungsschlüssels an. Wenn kein Sitzungsschlüssel angefordert wurde, ist dieser Wert 0.
The domain administrator can log on successfully over the RD Gateway. When i log on a domain user on the RD Gateway server console first and then log on over the RD Gateway, the authentication works fine.
The RD Gateway 2012 R2 has been installed as well as the instructions (http://technet.microsoft.com/en-us/library/cc754191.aspx). I have tried a lots of things, but without a result.
e.g.
register NPS in the AD
all ports in the Firewall between LAN and DMZ are opened
set the "Network security: LAN Manager authentication level" to "Send NTLMv2 response only"
re-install of the RD Gateway 2012 R2
Environment:
All machines have Windows Server 2012 R2 or Windows 8/8.1 with the latest updates. All servers are virtualized with Hyper-V.
Domaincontroller (LAN)
RD Sessionhost (LAN)
RD Gateway (DMZ)
Clients (DMZ/WAN)
Hardware-Firewall (3-zone)
Does anyone have an idea, what might be the problem?
Best regards,
BpDkHi,
From your description seems there is user permission issue and that’s the reason you can’t logon to the remote desktop. For this you can I would like to check whether you have done the following steps for troubleshooting.
Need to create RD CAP and RD RAP policies and also add the user under RD CAP properties for proper access. RD CAPs allow you to specify who can connect to an RD Gateway server. You can specify a user group that exists on the local RD Gateway server or in Active
Directory Domain Services. You can also specify other conditions that users must meet to access an RD Gateway server. You can list specific conditions in each RD CAP. For example, you might require a group of users to use a smart card to connect through RD
Gateway.
When there is no AD DS in the perimeter network, ideally the servers in the perimeter network should be in a workgroup, but the RD Gateway server has to be domain-joined because it has to authenticate and authorize corporate domain users and resources.
Please check below article for more troubleshooting and provide access & authenticate user.
RD Gateway deployment in a perimeter network & Firewall rules
http://blogs.msdn.com/b/rds/archive/2009/07/31/rd-gateway-deployment-in-a-perimeter-network-firewall-rules.aspx
Hope it helps!
Thanks.
Dharmesh Solanki
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Maybe you are looking for
-
DVD/CD optical drive is recognized only occasionally and temporarily
Hi, I recently bought an ASUS Essentio desktop model CG8350 running Windows 7 Home Premium 64-bit. My DVD/CD optical drive is not consistently being recognized. I've made few changes to the computer and have even tried reinstalling Windows (system re
-
Using Time Machine to backup a iMac G5 and restore to an intel iMac
Is it possible to use Time Machine to backup my iMac G5 and restore my backup to a new intel iMac? The reason being is that I my mother-in-law's company bought her a new intel Mac and she wants to trade with me since she only uses her Mac for e-mail,
-
How do I download an XPI without Firefox trying to install it?
Mail Redirect, a TB addon, recently switched to Sourceforge because MozDev was shutting down or something. However, attempting to download the latest XPI from Sourceforge (http://downloads.sourceforge.net/project/mailredirect/mailredirect-0.7.7-sm%2B
-
How to Customize the sqlplus in 11g?
Hi all, I am Using Oracle Database 11g R1 on Windows 2003 Server Edition R2. 1. I have Created a Batch file it call the sqlplus.exe file (i am using Silent Mode -s ) for Dropping and creating a user in My test DB, I want to Customize the DOS Window o
-
Is it possible to import AI CS5 settings into AI CC 17?
I would like to use Illustrator CC 17's import feature to bring in my CS5 settings but it doesn't seem to work. Does anyone know if it's possible?