Problem with hp color laserjet c1515n

I have problem with my HP color laserjet C1515n it prints in different shades printing jumps prints magenta at one place and cyan at one place and yellow at one place.....its printing is jumping.....to know the real problem it was better to attach a print copy but there is no option to send any attachment to u....kindly help to solove the issue.

Hi Arthur, and a warm welcome to the forums!
Sometimes you need to habd uninstall hp drivers, but Might try these two...
Mac OS X: About the Reset Printing System feature ...
http://support.apple.com/kb/HT1341?viewlocale=en_US
Might try Printer Setup Repair 5.1...
http://www.fixamac.net/software/index.html
Do this before & after any install...
Safe Boot. One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions.
Reboot.
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.

Similar Messages

Problem with HP Color LaserJet 2840

Hey guys, first post here woot woot haha
Now to business
I have a macbook with osx 10.4.11, and an HP Color LaserJet 2840. I can't get it to print through USB.
This guy on the HP forum had the exact same problem
http://forums13.itrc.hp.com/service/forums/bizsupport/questionanswer.do?admit=10 9447627126316290000128353475&threadId=1198993
The thing is, I can't call Apple like the guy on the HP forum did. I need your help to solve my problem!!
Thanks a lot, and take care!!! ---Arthur

Hi Arthur, and a warm welcome to the forums!
Sometimes you need to habd uninstall hp drivers, but Might try these two...
Mac OS X: About the Reset Printing System feature ...
http://support.apple.com/kb/HT1341?viewlocale=en_US
Might try Printer Setup Repair 5.1...
http://www.fixamac.net/software/index.html
Do this before & after any install...
Safe Boot. One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions.
Reboot.
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.

Printing problem with HP Color Laserjet 3000 printer

I am using HP Color Laserjet 3000 printer, it is configured in SAP ECC6 with SPAD with device type "HPLJ4 : HP Laserjet 4 series PCL and access method = L: Print Locally Using LP
At HPUX level printer in configured with proper driver also.
When I print from SAP, I get following error
"Invalid option, Please refer to MAN page for valid options" as attached
Other then above line , nothing else comes
Please help,
Al Mamun

Hi,
Make a try using the device type HKSAPWIN and the access method is front end prinitng.
Also make sure that you are able to take the print out using the os(printer should be configured at os level first).
Regards,
Vamshi.

Problem with HP Color laserjet CP1515n !

Dear anyone,
My HP Color laserjet CP1515n is running wilde, because it prints every single page with black stripes on the margin. I have tryed to start the cleaning mode several times, but it does over and over again...
Please, hase anybody any experience regarding to such behaviour?...
Thanks a lot
/E

Hi - I have not seen this issue, but let me see if I can get some more information in order and try to help.
(1) Are the stripes running vertically down the page, or are they running horizontally across the page? If running horizontaly across the page, what is the distance (in millimeters) between each defect?
(2) Is the product (and cartridges) new? Did the product (and cartridges) ever work normally?
(3) Please print 5 pages that have color and then print 5 pages that only have black and white text. Do you see the defect on all 10 pages?
These types of issues are difficult to troubleshoot without seeing the defect, but maybe I can offer some help based on the answer you give.

Problem with HP color laserjet CP3505

Hi all,
I am having a Problem with my printer CP3505, i fitted this printer in my network and it is printing perfectly good at first even from my Mobie (S4) and other systems in my network, but recently a problem started its printing only from one laptop. when i send data to print either from my mobile / or from any other device the data indication on the front panel of the printer keep blinking and after some time an error appears saying cant connect to the printer.
can some one help me out.
Many thanks

Hi KKRahul, and welcome to the HP Forums.
I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at http://h30499.www3.hp.com/hpeb/ .
I hope this helps!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Printing problems with HP Color Laserjet 1500L

Can anyone please help me with the following problem?
The printer will only do the first job. After that it refuses to print. The job stops, remains in the queue, and cannot be started.
Or…it looks as if it sends the print information to the printer – the green light of the printer flashes – but nothing further happens. The queue is empty and the job’s name even appears in the completed section.
The HP 1500L and the USB port are visible in the System Profiler. I have downloaded and installed the latest driver and did run Repair Disk Permissions.
I can only print again after I restarted or unplug and (re)plug the USB cable (not always). The cable is not faulty...but I'm going crazy.
I am new to the Mac world. The MacBook Pro being my first (and the way it looks definitely not the last--wonderful machine).
Any suggestions?

To use the OS X standard network protocols (Windows/IP printing), you must have either a postscript printer (the driver in that case is just a ppd for the OS X postscript output) OR, a driver designed to work with CUPS (CUPS driver). HP doesn't provide CUPS drivers for OS X (who knows why, since they do for linux).
You need to install foomatic and ESP ghostscript:
http://www.linuxprinting.org/macosx/foomatic/
then, install the foo2oak driver:
http://www.linuxprinting.org/showprinter.cgi?recnum=HP-Color_LaserJet1500

Problems with "no color" in the "Fill and Stroke"

I am having problems with “no color” in the “Fill and Stroke” function of Flash CS4 Pro.
I had been using CS4 for 10 days and everything worked fine. Then I tried experimenting with various color combinations (along with “no color”) for “Fill and Stroke” for a simple button. Suddenly CS4 locked up on me while I was working with the “color panel”. A second color panel appeared in the upper left corner and the program was not responding. All I could do was to end the CS4 task.
After that, whenever I created even a simple rectangle, at first the colors would appear as indicated for “Fill and Stroke”, but when I selected the object to see its properties, either the stroke or the fill color box would have a red slash line, indicating a “no color”, and I couldn’t select the color box to change it using the ink bottle tool, although the other box worked fine.
Rebooting did not help. So I uninstalled CS4 (and didn’t keep the preferences), rebooted, then reinstalled it. The problem was still there. Logging on as another user didn’t help. I tried restoring the Windows system to before I installed CS4 and resinstalling it and that didn’t work. I have a disfunctional CS4 now and I don’t know what to do to fix it. Please help me. Thank you.

Have you updated flash to 10.0.2? Have you played around with a bunch of different selections, objects, and so forth to see if this box is always incorrect? I think there's some particular selection (order of selecting things, and so on), where the color swatches in one location don't work as expected. However, it should not happen all the time and from what I recall it was fairly easy to work around (I can't even figure out what this was - so probably not it, as it seems hard to run into or perhaps now fixed).
Also make sure you have the stroke selected - if you don't have everything selected, either the fill or stroke will show no color and dim depending on the selection.

Problem to print with HP Color LaserJet CP3525 (PCL 6) on Server

Hi,
I have a printer HP Color LaserJet CP3525 in a server, and I installed with the correct drivers for that but the printing output is strange. I'm trying to print in A4 paper, and everything is just printed in 1/4 of the page. The most strange is that the graphics are scaled to the 1/4 of the page while the text is exactly with the same size than the complete page, but all the letter are overlapping each other.
I also tried to print with a generic configuration and print in all the page but I can't print with color, just the black toner is used, so the quality is really bad.
Please, help me!

This sounds like a driver issue. You mention the printer being PCL6. Can you confirm which driver you are using when the 1/4 page prints occur. My guess is that it would be one of the Gutenprint drivers included with SL and this sort of output can occur when the printer driver is not supported by the printer.
Also, with regards to the Generic, which I assume is the Generic PCL Laser Printer driver included with SL, this by default is set to 300dpi. You can change this print quality setting to 600dpi, which will improve your output, especially the graphics. However this driver only supports black & white printing. So if you want to print in color from the Mac and the printer does not support PostScript, then you should look at installing the pxlmono package.
http://www.linuxfoundation.org/collaborate/workgroups/openprinting/macosx/pxlmon o
Note that you will need the pxlmono, Foomatic and Ghostscript packages to use this driver suite.

Problems Installing WPSM54G with HP Color Laserjet CP2025DN

I have been trying to install the WPSM54G for use with my new HP Color Laserjet CP2025DN and cannot seem to get that to work. Although I have followed several pieces of advice in these posts and elsewhere, those do not seem to do the trick in my case.
> Checking that authentication is set to WPA and not WPA2
> Firmware/installer update
> Manual installation
> http://www.ehow.com/how_5396340_set-vista-vista-windows-linux.html
Although the printer is not on the compatibility list, neither was my Canon iPixma 4000, which connected just fine. Any guidance you can provide will be greatly appreciated!
Greg Manko

Connect WPSM54G to the router with the Ethernet cable. Connect the printer to the WPSM.
Now press the reset button on the print server for 5 seconds. See if you get any print out. If you get the print out, you will find the IP address of the WPSM. Using that IP address open the setup page of the WPSM and check the wireless settings. The wireless settings of your wireless router should match with the wireless settings of the WPSM.
If you do not get the print out then run the CD that comes with WPS. When you run the CD it will search for the print server and you will find the IP address of the WPS. Once you get the IP address you can exit the setup program and open the setup page of WPS. Check the wireless settings of the router and WPS.
Once you finish changing the wireless settings of WPS, you can disconnect WPS from the router and power cycle the WPS. Now try to ping the IP address of WPS when it is wireless. If you get replies then your computer is communicating with the WPS.
Now you will need to add printer port on your computer.
You can add the printer port using the CD or you can so it manually.
Run the CD again and go to the option setup computer. Follow the instruction and at the end try to print the test page see if that works.
You can add printer port manually also.
Follow this link to add printer port manually on Windows Vista.
Follow this link to add printer port on Windows XP.

PC doesn't communicate with HP Color Laserjet 1600

Hi, my Laserjet 1600 printer worked fine with my old pc. Now i have a new pc with Windows 7 ultimate 64 bit and somehow it can't communicate with my printer. Printer does work. cable isn't broken. Driver won't install either. What can be the problem? I also tried the HP universal printing PCL 5

Hi Reen1604,
I suspect your question would be better answered in the HP Enterprise Business Community, as the HP Laserjet 1600 is a commercial model.
My technical expertise is with consumer products and software, I am sure the commercial folks would be happy to help if you re-post your question for them to answer. The HP Enterprise Business Community is an HP Forum designed for the Commercial and Enterprise customers to help one another. I am sure you will find some HP folks there to help too.
Click here to view the Printing and Digital Imaging. When the page opens you will see the option to 'Log in' or 'Register Now' on the right. The commercial forums are separate from the consumer boards, thus you will need to register if you don't already have a commercial account.
You may find the HP Color LaserJet 1600 Printer page helpful while you wait for somebody in the commercial Forum to respond to your inquiry.
Best of luck.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Unable to print with HP Color LaserJet 2605dn since Upgrading to Mavericks

Since upgrading to Mavericks, I've had nothing but problems printing to my HP Color Laserjet 2605dn.
I'm having this problem on both my iMac and my MacBook Pro.
I get errors like:
"unable to write pirnt data broken pipe"
"unable to send data to printer"
"printer not connected"
I've been reading responses to others with similiar issues and I've tried
deleting and re-adding my printer.
reseting my printing system
Installing Guenprint.
re-adding my pirnter with a generic PCL driver.
None seem to correct the problem.
This problem happens both when connected directoy with USB and when connected through the network.
I have no problem printing with my work (Wondows) laptop.
Any help would be appreciated.

Thanks, a brody.
Yesterday (before I read your response), I downloaded the latest firmware (20140413.) (What do they say about great minds?)
I thought the issue may have been resolved.
I was finally able to print my bank statement on both the iMac and MacBook.
Today, I'm back to the the same issues.
Very frustrating, even though I've had the printer for five years, I've printed less than 20,000 pages.
In my mind, it's pointing more and more towards a hardware issue.

Mac lost contact with HP color Laserjet 3700 via USB

Hi,
Since a few days I can't get connection anymore with my HP color Laserjet 3700 via USB-cable. My Mac recognizes the printer with its name, also states when I plug in the USB that the printer is online. However, when I want to print documents, it states "wait until the printer is available" and no prints are generated.
Via an iMAC, I tried to print via the same USB cable, and that works fine. I tried rebooting, software updates, all the lot. Nothing worked. I found some technical details via About this MAC and the difference between my MacBook en iMAC is:
PPD-version = 16.4 on the iMAC and 17.3 on my MacBook
CUPS-version = 1.4.4 on the iMAC and 1.4.5 on my MacBook Pro
Who has any ideas what I can do the get printing again?
Thx,
Aldert

Via other threads I found the solution:
see: http://discussions.apple.com/thread.jspa?threadID=2640270&start=15&tstart=0
I had the same problem "Waiting for printer to become available... " - HP LaserJet 2500 L with iMAC 11.1 running Mac OS X Version 10.6.5. since the "HP Printer Software Update 2.5.2".
This also helped for me:
1) delete all of the items whose name starts with "hp_" in System/Library/Extensions
2) Disconnect the printer and turn off the printer
3) delete the printer if it's still there
4) reset the printing system
5) restart the Mac
6) empty the trash
7) turn on the printer and reconnect the printer to the MAC
8) reinstall the printer

Printing Acrobat files with HP Color LaserJet 2605dtn

Often, but not every instance, when I print an Adobe Acrobat file on the HP Color LaserJet 2605dtn Printer the following happens: the text prints as expected but the entire text area (but not the margins) is painted over with an orange red. This happens whether there is a graphic image in addition to text in the documents or when there is text only. With other Acrobat files, the text and/or graphic prints without a problem. I would like to know how to fix this problem.

It's featured on the forums before. For some reason Acrobat 8 doesn't go well with HP colour laserjet printers. I've suffered the same.
Two ways round it. Which preset (if any) do you use in Distiller to process the PS file? The red effect only appears when you use certain pre-sets.
I usually solve the problem by opening the PDF in Acrobat 6, not 8, and then printing from that

Problem with photos' colors

Hi,
I have a problem with colors of photos which I'm using in a. InDesign document.
I've created a 20 page catalog, with first and last pages for the front and back of the cover. I placed one photo on the first page and second on the last page. When I opened them earlier on in Photoshop they were matching perfectly, so I figured that it will be the same in InDesign. When I placed them in Indesign it turned out that the photo on the first page has a different color saturation (lower) than the one on the last page. It looks as if the first page was converted to CMYK and the last page was still in RGB mode (the photos were initially in RGB).
I decided to change the color preferences of the photos in photoshop to CMYK and saved thm again for InDesign, but it didn't help (I also checked all of the doc and color preferences in InDesign and all looked fine). It seems that colors are different on the last page only. Is it possible that it has a different color preferences set up? I'm a new InDesign user and I would be gratefull for You help :-)

It sounds like you have transparency of some sort (effects, drop shadow, tranparent image?) on the front and not on the back, and that the transparency blend space is set to CMYK instead of RGB while your image is RGB.
Edit > Transparency Blend Space > Document RGB

Sync problems with ipod color

Hi I'm having problems copying music onto my ipod. I am running iTunes 5 with the latest iPod software (1.2 from ipod updater 2005-09-23) on a windows XP platform with Service pack 2. My iPod is connected to my computer through USB 2.0.
When I plug my ipod to my computer, everything works fine, it gets recognized, I see the "do not disconnect" icon on the ipod and it starts syncing but the problem is, way before it finishes tranfering the songs, my ipod comes back to the main menu. I can read in iTunes that the transfer is complete and that it's ok to disconnect my ipod, even though it was NOT complete!
This really bugs me because I can't put all my songs onto my ipod and have to disconnect/reconnect it all the time to actually put my songs in it. What can I do to keep the transfer "alive" ?? please someone help me.

Hi,
I have the same type of problem with my iPod 20GB color running XP Home SP2. This happens when I import a large number of songs (over 100 or so) from my CD's in iTunes at one time. It will disconnect and then restart the transfer over again several times. I figured out that when your iPod is actually connected and doing the transfer, if you right click on the iPod (example: Joe Smiths iPod) in the iTunes left side menu, and click on "update" every 40 or 50 songs or so it will transfer everything without disconnecting. I discovered this yesterday while transferring about 270 songs to my iPod after it tried to automatically do it about three times. I don't know if this is the "real" fix for this but it worked for me. The problem doesn't appear to happen with a couple of CD's worth of songs.
Good luck!

Problem with hp color laserjet c1515n

Similar Messages

Maybe you are looking for