Problem with Hp Photosmart D110a for use with iPad 3G

I have just bought an HP Photosmart D110a for use with iPad 3G but this printer could not be connected to Internet, can anyone tell me what the problem is?

Hi,
Do you follow the setup guide ? What is the error ? Looks like your printer is not Airprint ready therfore you need to set it up for ePrint. 
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

  • Problems with repairing external HD for use with TM

    I've been trying all day to fix this. It was working earlier no problem, then when I went to restart my computer(after reinstalling mac osx) due to updates, i've been having trouble ever since. It doesn't mount, but yet it shows up in the disk utility. I've tried to repair it, and I get this:
    2008-11-30 20:41:26 -0500: Verify and Repair volume “Time Machine Backups”
    Starting repair tool: 2008-11-30 20:41:26 -0500
    2008-11-30 20:41:26 -0500: Checking Journaled HFS Plus volume.
    2008-11-30 20:41:26 -0500: Detected a case-sensitive catalog.
    2008-11-30 20:41:26 -0500: Checking Extents Overflow file.
    2008-11-30 20:41:26 -0500: Checking Catalog file.
    2008-11-30 20:42:36 -0500: Checking multi-linked files.
    2008-11-30 20:42:41 -0500: Checking Catalog hierarchy.
    2008-11-30 20:46:04 -0500: Checking Extended Attributes file.
    2008-11-30 20:46:10 -0500: Invalid record count
    2008-11-30 20:46:10 -0500: Volume check failed.
    2008-11-30 20:46:10 -0500: Error: Filesystem verify or repair failed.2008-11-30 20:46:10 -0500:
    2008-11-30 20:46:10 -0500: Disk Utility stopped repairing “Time Machine Backups” because the following error was encountered:
    Filesystem verify or repair failed.
    2008-11-30 20:46:10 -0500:
    Any suggestions or ways to fix this? All my files are on this HD...

    One of the things you listed is a case-sensitive filesystem which can be troublesome.
    Run DU and look at your internal HD.
    Click on the partition and down below you will see Format: Mac OS Extended (Journaled)
    I believe that it will also say "Case Sensitive" if it is.

  • Not able to create OUT file with "nidll_vxworks" in Matlab for use with the LabVIEW SIT 2010 and a cRio 9073, sh.exe error

    I am trying to compile an OUT file for my Simulink model using "nidll_vxworks" and run it using the Simulation Interface Toolkit for a cRIO 9073 . I am able to compile the DLL file using "nidll" and succesfully run the simulation using my PC as the host.
    I already downloaded the "gccdist" and "vxworks61gccdist" folders and copied them to "c:" When I build the model in Sumulink I get the following error at the end of the process (at the same time windows tells me that "sh.exe" has stopped working). If it matters I am running Windows 7 64bits, but using Matlab 2009b 32bits and LabView 2010 32 bits. ANY HELP WILL BE APPRECIATED. "QofV" is the name of my Simulink model and I changed to "XXX" parts of the file path.
    ### Linking ...
    rm -f "QofV.out" ctdt.c;nmppc QofV.o QofV_data.o rtGetInf.o rtGetNaN.o rt_logging.o rt_look.o rt_look1d.o rt_nonfinite.o  nidll_main.o rt_sim.o ode8.o    | tclsh c:/gccdist/WindRiver/vxworks-6.3/host/resource/hutils/tcl/munch.tcl -c ppc > ctdt.c 
    abnormal program termination 
    C:\Users\XXX\AppData\Local\Temp\make426012.sh: fork failed: no child processes [1]
    make: *** [QofV.out] Error 1 
    ### Real-Time Workshop build procedure for model: 'QofV' aborted due to an error.
    >> 
    ### Linking ...rm -f "QofV.out" ctdt.c;nmppc QofV.o QofV_data.o rtGetInf.o rtGetNaN.o rt_logging.o rt_look.o rt_look1d.o rt_nonfinite.o  nidll_main.o rt_sim.o ode8.o    | tclsh c:/gccdist/WindRiver/vxworks-6.3/host/resource/hutils/tcl/munch.tcl -c ppc > ctdt.c  
    abnormal program termination 
    C:\Users\XXX\AppData\Local\Temp\make426012.sh: fork failed: no child processes [1]make: *** [QofV.out] Error 1 ### Real-Time Workshop build procedure for model: 'QofV' aborted due to an error.>>
    ### Linking ...rm -f "QofV.out" ctdt.c;nmppc QofV.o QofV_data.o rtGetInf.o rtGetNaN.o rt_logging.o rt_look.o rt_look1d.o rt_nonfinite.o  nidll_main.o rt_sim.o ode8.o    | tclsh c:/gccdist/WindRiver/vxworks-6.3/host/resource/hutils/tcl/munch.tcl -c ppc > ctdt.c  abnormal program termination C:\Users\XXX\AppData\Local\Temp\make426012.sh: fork failed: no child processes [1]make: *** [QofV.out] Error 1 ### Real-Time Workshop build procedure for model: 'QofV' aborted due to an error.>> 
    Solved!
    Go to Solution.

    Hello jarcTec,
    I am not sure right now if you can do it, but this tutorial might help, also everything was made in Winddows 7 in this one.
    http://zone.ni.com/devzone/cda/tut/p/id/11654
    Take a quick look and let me know if it works!!!
    Luis Fernando
    National Instruments Cono Sur
    Ingeniería de Campo y Consultoría
    http://chile.ni.com/

  • Problem-Starting InDesign Server for use with CORBA / Java and IOR file not generated

    I'm trying to start Indesign Server cs3 for use with Corba, as per the document the server should generate the start-up message like this..
    InDesignServer -iorfile c:\ior.txt -pluginpath Server\Corba
    [server] Writing IOR to ... and it should generate the IOR file
    but I'm getting the usual start-up message and the IOR file is not generated, I hope IOR file is required for Java component interaction with IDS, kindly help me to solve this.
    Thanks in advance.

    [From Susan Doan, who is having trouble posting to the forum today}:
    It looks like the example command line in the "Intro to InDesign Server" pdf is using curly quotes instead of straight quotes. If you copy the command from the pdf and paste it in your command shell, it won't work because of the curly quotes.
    You can run the command without the quotes as Rich has said, but, as will all command lines, if your path contains a space, you will need to put quotes (straight ones!) around the path.
    Thanks,
    Ole

  • Doesn't play songs, "itunes is not configured for use with mac-formatted"??

    Hi, new ipod shuffle. Seems to charge fine, all indicator lights function as expected. Everything looks fine in itunes. But it doesn't play songs. I have the most recent versions of itunes and the ipod software. Re-set, updated, and restored, nothing works. Even restored using the restore utility. Re-started computer. Checked for volume control. Won't play songs. Tried different file types. Songs play fine from itunes library and from the device's library within itunes. Tried different headphones. Hooked it up to computer speakers. Turning volume all the way up on device and speakers, heard some very faint rhythmic static, so my guess is the jack socket (or whatever you call it) is just messed up, but it seems weird that it can transfer power and data to the device but doesn't work for sound...
    The only other issues that have come up is that the drive disappears in explorer once it syncs with itunes. Other people who've noticed this seem to have completely different problems so I don't think it's related.
    Also, I have MacDrive on my computer. And when it starts up with the ipod plugged in, MacDrive offers the message "Itunes is not configured for use with Mac-formatted ipods." It offers to automatically reconfigure itunes so it can read mac-formatted ipods. Since I've restored the device, I don't see why formatting should be an issue so I say "no."
    Should I try letting macdrive do its format thing? Should I try formatting the ipod disk on the My Computer menu? Or should I just email apple and tell them the jack's busted?
    Thanks for any thoughts!

    Well, I have had my iPod for about 3 years, it is a 4th generation non-video 40 GB. One day it just stopped working, and now it does not play any songs. when I turn it on it makes this odd whirring sounds that computers make when they try really hard to do something. I cannot charge it, and it is not recognized by iTunes. Also when I turn it on, I get the apple.com/ipod/support (or whatever it is) screen. Needless to say, my warranty is expired, and so I cannot do anything for it except get a new battery, or buy a new one. Is there any way to fix this problem, or anyone out there who is experiencing the same thing?
    I'm having the exact same problem with my wife's iPod. However it will play about 3 seconds of a song and go onto the next song.
    If there is anyone out there that can help please do!
      Windows XP  

  • Can I activate ePrint on my HP Officejet Pro 8500 Premium printer for use with my smartphone​?

    Can I activate ePrint on my HP Officejet Pro 8500 Premium printer for use with my smartphone? Any instructions?

    Yes.  You can do that
    Just follow the instructions for the appropriate device on this HP web document. 
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Partitioning an ext. HD for use with Time Machine HFS+/FAT32

    Hi, I hope that this question is not already answered somewhere - I did a couple of searches but couldn't find the answers I need.
    I'm setting up an external LaCie 500GB HD (USB 2.0) for a friend, in order to use it for Time Machine backups (one partition) and as a non-backuped "data dump" (music / films etc.).
    My plan is the following: Partition the ext. HD into a 200 GB HFS+ Journaled partition for use with Time Machine, and a 300 GB FAT32 partition for data (FAT32 to ensure the interoperability with PCs).
    I have a couple of questions (apart from if you think the proposed setup is good in general):
    1. The Time Machine partition would be used to back up a MacBook with a 120GB HD - in your opinion, is 200GB too much/enough/too less space?
    2. In general, does Time Machine work with partitions on ext. HDs as seen in the setup I propose? (or should I use a drive with only one partition?)
    3. are there any possible problems I might run into when partitioning a drive into two different file systems as HFS+ and FAT32?
    4. Is it OK to use the Leopard Disk Utility for this or should I use another application?
    thanks a lot for your answers!

    Hi,
    Could you please share the answers you found?
    I'm going through a very similar situation...
    Thanks!
    Beto.

  • V-41 tcode error :Table 304 is not defined for use with condition type PR00

    Hi All,
    I am trying to create a BDC using the transaction V-41. 
    The first screen has fields:
    ConditionType and Table, where I have to fill values ZPM1 and 800 respectively.
    But as soon as I enter the tcode v-41 and say enter, the above mentioned fields are already having the  values 'PR00' and ' 304'. Normally if you take an example fo t-code VA02, all fields are blank.
    Then an error message  is displayed:
    Table 304 is not defined for use with condition type PR00
    This behaviour is not allowing me to use the BDC feature.
    Please advise me on why this is happening. What are the possible solutions I can use to clear these values programmatically?
    Can anything be done via customizing?
    Regards,
    Namita.

    Dear ILHAN ,
    Well the problem you are facing is having the following solution:
    Table 304 is not defined for use with condition type PR00
    Message no. VK024
    Diagnosis
    The selected condition type does not fit in the condition table, that is the basis for the condition record. Alternatively the selected condition type is not included in the condition types that were selected on the selection screen or that are defined in the variant of the standard selection report.
    Procedure
    Úse F4 help to choose a valid condition type.
    If this does not give you the required condition type, check in Customizing for condition types and the related access sequences.
    In the condition maintenance also check Customizing for the selection report (pricing report), that you have selected in the navigation tree, using the standard condition table as a reference.
    I hope this helps.
    It has worked for me.
    I gave it a try and what I am getting using the transaction V-41 is create Price condition (PR00) : Fast Entry.
    Please award points if you find it useful.
    Regards,
    Rakesh

  • Do i need to reformat a samsung m3 for using with a macbook pro

    Hello
    Do i need to reformat a new samsung m3 for using with a macbook pro?
    I have an old bipra which i use and i just remember literally plugging it in and going.
    thanks for any info.

    I don't know about your particular configuration but usually Disk Utility not recognizing a drive means the drive/card is history.  My G4 running OSX 10.4.11 will format SD cards.
    I don't know your model computer. Is this one with a SD slot built in?  If it is, do you have an external reader, or can you try another card in this slot to see if it is a slot problem?

  • Best wireless router (apple or non-apple)  for use with multiple Macs

    What is the best wireless router, from any manufacturer, for use with 3-5 Macs? (in a reasonable price range... sub $150)
    least problems
    most reliable
    strongest signal/best range
    fewest drops
    fewest reboots

    The Apple Routers "just work".
    I also have a linksys. It takes a good bit of knowledge and aggravation getting it set up, but once working it does fine.
    If you plan to use your router to share a printer, hook to your stereo, etc. definitely stick with Apple. It will save you much grief.

  • What is the best software to use for screen capture on a PC for use with FCPX?

    What is the best software to use for screen capture on a PC (windows 7) for use with FCPX? I've tried Camtasia and camstudio however the avi files cannot be imported by FCPX and the mov files produced by these programs are shown as just black screens in FCPX.

    I use to face this issue every now and then (as a freelancer) when I use to cut on FCP7.
    if the material is DV and was captured using Sony VEGAS, Premiere or Edius, the footage generally worked fine. You'll find most people will tell you to convert it regardless, however I found no issues working with them.
    A problem you'll definitely face is HDV material. Most PC editing software write HDV in their own codec, which can't be read in FCP.
    The only thing I can think of is to try converting HDV meaterial to QuickTime using something like MPEG Streamclip, or something similar.
    Good luck

  • USB portable ext. HD for use with MBP & FCE????

    I've seen a 120 GB USB portable external Seagate HD for $117. Would this be usable as a scratch disk for use with my MBP 2.0 and final cut express HD 3.5. Are there problems with using USB externals? FW external hd's seem to be a good deal more expensive.
    This may belong in the FCE forum but I thought someone here that uses an MBP might have specific experience with it.
    Thanks.
    Maurice

    I use a Seagate 160GB 2.5" 5400 external as mirror/scratch partitions and it works OK however, if I'm capturing at high res I usually write to the internal drive (that's running at 7200) to avoid any frame loss ...

  • USB external portable HD for use with FCE and MBP ???????

    I've seen a 120 GB USB portable external Seagate HD for $117. Would this be usable as a scratch disk for use with my MBP 2.0 and final cut express HD 3.5. Are there problems with using USB externals? FW external hd's seem to be a good deal more expensive.
    Thanks.
    Maurice

    I bought one recently very cheaply to use for general storage.
    I found that FCE 3.0 worked perfectly and have been using it ever since instead of my FW HD.
    HOWEVER, before you dash out and buy one take note that I have only been tinkering around and experimenting with comparatively short projects of no importance.
    I strongly suspect that if I made a long and complicated film I might suffer - so pay the extra and get a FW HD !
    Incidentally for normal storage purposes the USB2 HD takes over twice the time to move files back and forth. So even for non-FCE use the Firewire HD is twice as fast.
    Ian.

  • JDBC Error: This driver is locked for use with embedded applications

    Hi Experts,
    My sender adapter is throwing the below error:
    Error during database connection to the database URL 'jdbc:nwmss:sqlserver://<host>:<port>;databaseName=<dbname>' using the JDBC driver 'com.sap.nwmss.jdbc.sqlserver.SQLServerDriver': 'java.sql.SQLException: [NWMss][SQLServer JDBC Driver]This driver is locked for use with embedded applications.'
    What could be the problem? How can I resolve it?

    download the latest version of SQL driver from MS site and re deploy it on PI

  • External Hard Drive for PowerMac G5 for use with FCP Studio

    Hello,
    I'd greatly appreciate any recommendation for an external hard drive for a PowerMac G5 for use with FCP Studio.
    Thanks.
    -graziemile

    We see alot of Lacie issues here and elsewhere.
    Drives fail... period. I believe you hear more about Lacie drives failing because they sell a ton more of them than many other suppliers. I've got 8 of em sitting right here on the desk and two more at the second station. I've lost one since I started using them years ago (and it had problems right out of the box) and I use them pretty heavy.
    I understand that they use several different brands of drives in their enclosures, but from my experience they must have pretty good QC standards for what they package.
    The guy said the G Techs were a little overkill for his needs. Lacie doesn't pay me. But if someone asks "how are Lacies?" I'll tell them they've been great for me and many others I know, especially if your requirements are capturing DV.
    In five years, I ain't heard anybody say anything about it.
    As for FCP. I love it! In 20 years of business, it's probably the purchase that's given me the most bang for my buck. But if you haven't heard people knock it, you've never met an Avid zelot, bruhhhhh, just the thought gives me shivers.
    The drives X mentioned are designed for video work.
    What Studio said, well he gives out some of the best advice on this board
    (and maybe the most! ) and my reply to his post... that's why I used the little smiley face. No offence intended X.
    I only meant to say that, in a world where software like FCP can do what it does at the price it does it, and drives like Lacie and G Tech can give you the storage they do for the price they do, the line between consumer and professional products is easily blurred.
    rh

Maybe you are looking for