Problem with KT4V mainboard

I have:
AMD athlon 1900XP+, MSI KT4V (not raid), 256MB DDR (333MHz), BARRACUDA IV 80GB, GF440MX etc. OS: WindowsXP Profesionall
When i plug second HDD (BARRACUDA IV 80GB) on secondary master and i want copy data with Primaty HDD to Secondary HDD my computer will restart ?(
HELP MEEEE!!!!![size=15]TaRuS[/SIZE]

Hi,
1. What is your power supply?
2. Did you place your hdds very close to each other? possible overheating can cause such error... make sure your drives get cool properly.
3. What are the jumper settings for the drives?
4. Is your WinXP from a clean installation? Or you did an upgrade on the motherboard without OS installation?
5. Does this occur to ALL data/file? Or just once in a while?
 

Similar Messages

  • Problem with KT4V

    Hello.
    I have a problem with my mainboard. How can i disable a sound from pc speaker at computer start?
    When i On him, there are a lot of BEEP's and nothing happens. Then I must restart and everything is OK.
    What can I do?
    --sorry for my english-- ;(

    You Need to count the beeps before you can find out what is or is not happening to your pc
    This is a list of beep codes that will give you an idea as to why not booting, hope they help
    1 short DRAM refresh failure The programmable interrupt timer or programmable interrupt controller has probably failed
    2 short Memory parity error A memory parity error has occurred in the first 64K of RAM.  The RAM IC is probably bad
    3 short Base 64K memory failure A memory failure has occurred in the first 64K of RAM.  The RAM IC is probably bad
    4 short System timer failure The system clock/timer IC has failed or there is a memory error in the first bank of memory
    5 short Processor error The system CPU has failed
    6 short Gate A20 failure The keyboard controller IC has failed, which is not allowing Gate A20 to switch the processor to protected mode. Replace the keyboard controller
    7 short Virtual mode processor exception error The CPU has generated an exception error because of a fault in the CPU or motherboard circuitry
    8 short Display memory read/write error The system video adapter is missing or defective
    9 short ROM checksum error The contents of the system BIOS ROM does not match the expected checksum value.  The BIOS ROM is probably defective and should be replaced
    10 short CMOS shutdown register read/write error The shutdown for the CMOS has failed
    11 short Cache error The L2 cache is faulty
    1 long, 2 short Failure in video system An error was encountered in the video BIOS ROM, or a horizontal retrace failure has been encountered
    1 long, 3 short Memory test failure A fault has been detected in memory above 64KB
    1 long, 8 short Display test failure The video adapter is either missing or defective
    2 short POST Failure One of the hardware testa have failed
    1 long POST has passed all tests  

  • Problems with KT4V and AtiRadeon 9700 Pro...

    Hi all,
    I have lots of problems with my current configuration with games (lock ups) and even in normal use. Also I'm not able to run 3DMark through to see with kind of results would I get. Car chase (high) gets very low fps and the nature test doesn't even work. I have tried different 4in1 drivers and BIOS versions. With 1.6 BIOS version I had lots of CRC errors (should be corrected in BIOS ver. 1.7 but in expense of data rate?).  Does anyone have any suggestions so that I could for example go through the 3DMark even with the expense of performance?
    I had those game lock up problems also earlier with KT7A-100 RAID + AtiRadeon 64 (3DMark worked) so I bought new graphic card (didn't help) and after that I bought the new mobo. I know my config is not the best in the world, but I think it should be enough to give some happy moments in ever so demanding games... for a while...
    There is also one thing that is quite strange. In my display adapters there is two drivers for AtiRadeon (primary in AGP and secondary in PCI)? I'm not expert, but isn't that weird? I have tried installing different drivers again and again (also reinstalled OS) with no luck! Trying to delete the secondary one doesn't help...
    Help..........!
    My specs:
    MSI KT4V (MS-6712)  4in1 Hyperion 4.45, BIOS ver 1.0
    AMD TM 1.2 GHz CPU
    ATX pro3 (300W)
    WIN 98SE
    512 MB DDR (333)
    SAMSUNG 40 GB (5400 RPM)
    SAMSUNG DVD
    ATIRADEON 9700 Pro (Club 3D)  Catalyst 3.0
    Soundblaster Live!

    the 9700 is the most powerfull vga to date and needs power evan more than a gf4 4600
    i would lbe looking at some think like an antec true powe 430 watt psu not a basic 300 watter
    with ati,s own cards you need revision 1.3 as well best i can recall,but yours is an oem so im not sure
    a search for 9700 in this section will get you lots of threads

  • Strange problem with KT4V

    I have a strange problem with the board
    when booting,the cdrw only blinks and can`t read cd`s.
    I have tried swapping to another cd-rom,but still the same problem.I updated to the new bios (1.9)without problems.
    my specs are:
    KT4V
    512MB PC2700
    MAXTOR 80GB HARDDISK
    MSI 52X24X52 CD-BURNER
    MSI GeForce4 Ti4200 64MB DDR DVI

    Quote
    Originally posted by THE VIKING
    I updated to the new bios (1.9)without problems.
    When begun it to happen?
    Before or after the BIOS update?

  • IDE problems with KT4V-L?

    Hi, I am trying to resolve a long standing problem with regards to cd/dvd drive issues - both with reading and burning. I have had a system based around the KT4V-L mobo for about 3 years now and about 2 years ago I started experiencing problems with my msi cdrw drive- problems reading and burning discs, both blank and written. I tried various possible solutions i.e. new cable, different ide placement, firmware upgrade, different burning software, via drivers, various WXP tweaks, mobo bios upgrade/tweaks, even a fresh XP install (vanilla xp pro) but nothing would stop me churning out coasters. I then thought that the drive itself must be faulty and swapped it for a new one only to have exactly the same problem. I limped on for a good while (everything else works just fine) until dual layer dvd burners got cheaper and decided to swap my cdrw for a samsung dl dvdrw. Still same problems... especially with dvds. Another fresh install of WXP pro (sp2) has yielded no improvement nor has trying mandrake linux (ver. 10). Anyhoo, my thinking now is that there may be a fault with the onboard ide controller although my HDD has always worked fine... As I said before, I have tried all the different placements/settings with regards to ide connections/cables/jumpers and bios settings.
    Sorry to bang on for so long but it has been driving me slowly mad for a good while   Any help gratefully received as I am on the verge of binning the mobo and just buying a new (different) one...
    MSI KT4V-L (Bios ver. 1.9)
    AMD Athlon XP 2200+
    2 x 512 MB DDR PC2700
    MSI GeForce4 440SE AGP8x (64 MB)
    SoundBlaster Live! Value (CT4670)
    HDD 0 Maxtor DiamondMax Plus 9 60 GB Ultra-ATA/133
    TSSTcorp CD/DVDRW TS-H552B
    Channel Well Technology 350W 3.3v - 20A, 5v - 35A, 12v - 17A
    WinXp Pro SP2

    Thanks for the response osnavi, the first cdrw drive was well under a year old when I changed it and had only had light to medium use. I agree that the power supply could be better but the fact remains that everything worked perfectly for the first year-ish. At that time I actually had another dvd drive alongside the cdrw with no problems until this issue arose- I then had to physically remove the dvd drive to get the cdrw working at all. I currently have my HDD as primary master and the dvdrw as secondary master but as I said previously I have tried all the various settings available. The HDD is running in ultra dma mode 6 and the dvdrw is ultra dma mode 2 - I did have to reset this as WXP had demoted it to PIO mode only, presumably due to multiple errors... Re. the power supply issue, is it possible that the system ran fine for a year (with slightly more load due to the extra dvd drive) and then just b0rked out? I have had no other issues at all with this system and I am a fairly application heavy user (photoshop, quark, fps games etc). Is it also possible that the upgraded bios may have caused the problem as I did flash it from the original OTB bios to version 1.9 as directed by the msi live update system?
    Thanks again for your interest.
    MSI KT4V-L (Bios ver. 1.9)
    AMD Athlon XP 2200+
    2 x 512 MB DDR PC2700
    MSI GeForce4 440SE AGP8x (64 MB)
    SoundBlaster Live! Value (CT4670)
    HDD 0 Maxtor DiamondMax Plus 9 60 GB Ultra-ATA/133
    TSSTcorp CD/DVDRW TS-H552B
    Channel Well Technology 350W 3.3v - 20A, 5v - 35A, 12v - 17A
    WinXp Pro SP2

  • Restart problem with kt4v motherboard

    I have a kt4v motherboard with an athlon xp2600 processor and the whole computer just randomly reboots and then when it gets to the xp load screen(after bios set up) it rebbots again and again. can anybody tell me whats happening and how to sort it out?

    The only way to find an answer is knowing much more about your PC: Video card ? Memory ? Power source ? O.S. ? Peripherals ? Heat sink ? and so on. Look at your Power Source about teh dif. Volts-Amp it gives and the brand. 8)

  • Big Problem with KT4V. PLEASE HELP!!!!!!

    Hello ewerybody.
    At first I describe you my confiugaration.
    KT4V Mainbord
    AthlonXP 1700+
    256MB DDR 333
    Segate Barracuda 20GB
    CD-ROM LG 52X
    Power Supply 230V
    WIN 98SE
    And now the problem.
    It appears when the procesor is set to XP 1700+. After the temerature of processor rise obove 55 C my computer is shutdown automaticly even if the bios option "critical CPU themerature" is disabled. When it happens something like alarm siren goes off. It is one high and one low sound.
    Another big problem is dramaticaly low ( even 20% - after one hour work ) "system resources". I dont know if it is call like that in english so it is START->Settings->Control Panel->System->"performance".
    Please help!!!!!!!!!!!!

    First thing you might want to do is get a new PSU. Anything under 300W is pretty much going to make for an unstable system for any processor like yours. AMD recommends(if I remember correctly) 300W or better and also read up on this sticky, I think it will help you out.
    http://www.msi.com.tw/program/service/forum/index.php?threadid=1131&boardid=13&styleid=1
    Especially the Power Supply paragraph  8)

  • Big problem with KT4V(MS-6712)

    ok, i ordered two of these motherboards, for me and one for my friend, mine works fine, but his fails to boot properly, at first he was having problems booting up the computer at all, with an amd 2100+, and it wouldnt boot, he eventually found that when the graphics card was removed it booted, ok so the boards boots, what about graphics!, ive tried it with a geforce 2 ti and a geforce 4 4800 se, it boots, but the moniter is just left unstarted as if on "idle" there is no display on the moniter but the computer boots, my board works fine with these cards, any ideas what it could be, ??? or just a case of faulty motherboard?
    any help much appreciated

    well, i put the d - bracket in, and all four leds remained as red, which by the manual means
    "System Power On"
    -  The D-LED will hang here if the processor is damaged or not installed properly"
    ok fair enoguh, its the processor? - No, i tried a 1600+ in it which wouldnt work either, same result, "
    oh , i just realised i forgot to put any RAM in when i just tested it, damn, will it still have gave no VGA output if no ram was in??? i also didnt plug in the speaker, just base - power switch and video card, so i wouldnt have heard any audial warnings, ok well i guess im gonna strip the computer out AGAIN :O  and change the mother board AGAIN :O , urgh, ok well, if anyone had any idea what it would be, as i have tried it WITH RAM in the other day, but without the D-Bracket™2
    thanks.

  • I have problem with :k7n2-vb"

    Hi, I'm Borislav Kiso from Yugoslavia and I have small problem with my mainboard "k7n2-vb". If it's a problem, i hope that you will tell me the answer. Mainboard permanently generate, with out any rules, bips. Even when I move my data from cd on hdd or when I play some game or install some programs.
    - 2500 barton box
    - k7n2-vb
    - 2 x 256/400 kingstone
    - rx 9550 td128
    Configuration works with no other problems so i think that it's a small problem but I can't find any specification on net.
    Best regards from SCG
    Borislav

    http://www.msicomputer.com/product/detail_spec/product_detail.asp?model=K7N2-V
    says it uses the nVIDIA® nForce2 400 Chipset
    http://www.rojakpot.com/default.aspx?location=3&var1=30&var2=0
    So, the only product that's actually new is the nForce2 400 which looks like a low-cost version of the Ultra 400 chipset. Unlike its feature-rich brother, the nForce2 400 offers only a single DDR controller and will not be able to support the MCP-T south bridge. However, it will still offer full support for the new 400MHz FSB, DDR400, up to 3GB of memory and AGP8X support. Not bad at all, especially IF NVIDIA sells it significantly cheaper than the Ultra 400 chipset.
    so im pretty sure im right

  • MOVED: [Neo4-F/Venice] Problem with downclocking

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=136087.0

    I found the main problem.
    I have two versions of windows:
    - xp pro sp2 integrated 01/2007
    - xp pro sp3 integrated 12/2009 performance edition, integrated all driverpacks
    Because I found some problem with hdd <-> mainboard communication in smart, i tried with some other hdd and tried to create all partitions once again.
    During installing xp sp3 on both hdd, i got bsod 0x7f/0x8e after decompressing driverpacks. This showed that this is not a problem with hdd. So I tried to install xp sp2 and it was working properly. Then I was installing drivers to verify which may cause problems:
    - graphic card - working
    - nforce - working
    - AMD Cool'n'Quiet - working
    - RMClock - bsods after each decrease of multiplier or voltage, cpu can work only on 9x and 1.4V
    Because it is problem with Cool'n'Quiet, I guess that it may be a problem with windows sp3 because driverpacks integrates AMD CnQ drivers. So I disabled CnQ in bios and tried to install xp sp3 once again. And.. it is working !!!.
    So the problem is with Cool'n'Quiet. I can't change any parameters of cpu because I get bsod each time. The best way is to disable CnQ in bios. On 1.4V and 9x it is working properly, no bsod under superpi and other cpu testing programs.
    I tried also to modify cpu multiplier in bios. Each decrease cause system freeze after showing system info in table and system can't boot. It is working only on 9x.
    Is it a problem with mainboard or cpu?

  • Problems with VIA KX133 + GF3 Ti200

    My system crashes after installing via 4in1 drivers (i've tried 4.28, 4.35, 4.43) runing 2D or 3D applications.
    When starting any 3dmark2001 test it crashes. Without via 4in1 i can run 3dmark2001 without problems but the results are extremely low.
    OS Win98
    MB Biostar M7MKB (via KX133 chipset)
    CPU Athlon 650 MHz (slot A)
    MS-8851 GF3 Ti200 64Mb DDR
    RAM 2x128 Mb Kingston PC133
    ATX 300W
    I mention that i didn't encountered anyproblems before installing the videocard, on my older RivaTNT2.
    Any sugestions?
    ++++++(i've also posted this inother forums so...)
    No irq conflict before or after installing 4in1. And the same happens under windows XP. I also tried 4in1 4.20 wich came with my mainboard. I also tried detonator 21.83 , 23.11 and 29.42 under Windows 98. No iam really out of ideeas. In bios the only options regarding AGP card are AGP memory (set to 64) and video bios shadow, so there's nothingto do there either. What can i try next?
    +++++++
    I've installed clean win98, then detonator 29.42 then modem and directx 8.1 (also tried 81.b). Then i made a backup of this state on another disk, wich i am reverting to after each unsuccesful try. So there is no driver mix-up. And no, there is no conflict before or after 4in1 installation. Also the system hangs apparently randomly in 2d apps. (but everytime i start MSOutlook ??!) and always in 3Dmark2001 at the begining. So, it functions ok but slow without 4in1, and crashes afterwards with 5 different versions of it.... My guess is ther might be a problem with the mainboard AGP voltage in4x or something (the 3D card runs ok on kt133 chipset with via 4in1 4.43)

    Thanx,
    I'm trying that now but the only option in bios is AGP 4x Mode (on/off). Is there any program able to switch between modes while running ?

  • [Neo4-F/Venice] Problem with downclocking

    Hi
    I have a problem with Athlon64 Venice 3000+ (1800MHz/1.4V) E3 on MSI Neo4-F mainboard. This system was working properly for ~5 years under following conditions. CPU was overclocked to 2250MHz (250MHz, 1.4V, HT 4x, DDR 208MHz). In idle it was downclocked to 5x multiplier at 1.1V using RMClock.
    A few days ago Windows was giving a lot of BSOD randomly. Then I went back to basic frequency but it didn't help. I checked memory with Memtest also but there was no errors. So I decided to reinstall windows.
    After Windows installation was completed everything was working. Then I installed AMD CnQ driver and RMClock. And I found the reason of BSODs. CPU works properly with 5x and 9x multiplier (several minutes in SuperPI) but system halts after changing the voltage. Down to 1.225V everything is OK but then I set 1.2V and I get BSOD immediately. CPU temp is normal (23C idle, 38 load) and all fans are working.
    Why I can't lower the voltage to the factory 1.1V in idle? Is it a problem with CPU or mainboard?
    Regards

    I found the main problem.
    I have two versions of windows:
    - xp pro sp2 integrated 01/2007
    - xp pro sp3 integrated 12/2009 performance edition, integrated all driverpacks
    Because I found some problem with hdd <-> mainboard communication in smart, i tried with some other hdd and tried to create all partitions once again.
    During installing xp sp3 on both hdd, i got bsod 0x7f/0x8e after decompressing driverpacks. This showed that this is not a problem with hdd. So I tried to install xp sp2 and it was working properly. Then I was installing drivers to verify which may cause problems:
    - graphic card - working
    - nforce - working
    - AMD Cool'n'Quiet - working
    - RMClock - bsods after each decrease of multiplier or voltage, cpu can work only on 9x and 1.4V
    Because it is problem with Cool'n'Quiet, I guess that it may be a problem with windows sp3 because driverpacks integrates AMD CnQ drivers. So I disabled CnQ in bios and tried to install xp sp3 once again. And.. it is working !!!.
    So the problem is with Cool'n'Quiet. I can't change any parameters of cpu because I get bsod each time. The best way is to disable CnQ in bios. On 1.4V and 9x it is working properly, no bsod under superpi and other cpu testing programs.
    I tried also to modify cpu multiplier in bios. Each decrease cause system freeze after showing system info in table and system can't boot. It is working only on 9x.
    Is it a problem with mainboard or cpu?

  • Problem with K9N DIAMOND at boot

    Hello,
    I've a problem with my mainboard K9N Diamon.
    I've this configuration :
    K9N Diamond
    Athlon X2 6000+ with Zalman 9700NT
    2x1go DDR 2 PC2 6400 at 800Mhz Corsair DOMINATOR
    Thermaltake Thoughpower 700W
    Case Thermaltake Kandalf VA9000BWS
    GeForce 7600GT Msi
    2x 320go WD HDD
    Dvd burn LG H42L
    So, When I plug the power cable, the pc turn on, but 3sec later it stop. I push the power button, nothink.
    I change the alimentation, with a 350w enermax, 500w PFC, 500w thermaltake, nothink.
    The D-Bracket tell me no infomation, at the shutdown after 3sec, the led are different at the last boot. Impossible to identify the problem.
    I test a 4200+ with 2x512mo DDR2 PC2 6400 at 800mhz corsair XMS2 and NX 6200 msi, but no change. When I plug the power cable it start, and 2 3 sec later it stop.
    I reset the bios, with this method :
    Code: [Select]
    1.Shut Down the PC.
    2.Unplug the Power Supply from the AC outlet and unplug the cord from the back of the Power Supply.
    3.If your Power Supply has an On/Off switch on the back of it turn it Off.
    4.Ground yourself and your PC.
    5.Remove all DDR2 DIMMs
    6.Remove the following power connectors on your mainboard:
       *JPWR1 - ATX 24-pin Power Connector
       *JPW1 - ATX 12V Power Connector
       *JPWR2 - ATX 12V Power Connector
    7.Clear CMOS.
    8.Reattached power connectors in Step 6 above.
    9.Place a DDR2 DIMM in DIMM3 (the slot closest to the CPU).
    10.Plug AC cord into Power Supply and AC outlet.
    11.If your Power Supply has an On/Off switch on the back of it turn it back On.
    12.Boot the PC.
    But no result.
    I test the CPU, graphic card and memory on other PC, It work fine.
    So, I think the mainboard is broken, I see problem like mine, but it's different here.
    I'm for MSI, I've all pc with this material, and all of my friend / custommer, but here I'm disappointed.
    This is an problem with a production series default ?  I dunno.
    So I I'am for MSI, and I think I'v bad luck in this moment ! 
    Sorry for my english, i come from Corsica ^^

    Thanks again for your answer and Help.
    I've trid to start with just : Athlon 6000+ / 512mo DDR2 .
    The system start, 2sec later stop. for restart with power button its impossible. I change the power button with reset button, same problem.
    I test with an screw driver, the system start when I plug power supply, and after 2 3second stop. I test to start with screw driver, I similar... but 10sec later, after short reset, hdd led, its start, for 2 3 sec ! LOL. To restart again, I did short reset, hdd, led, hdd, reset, power, reset, .......... and at one moment its star 2 3 sec !!! Dor restart I do it again. LOL.
    It's very strange. When its want , it start ! U_u
    So tomorrow, I contact my supplier to change the mainboard ^^ !
    I think its the only solution !
    Thank again for your help, If you have many idea, I take that again :p
    See you soon

  • KT4V Problems with 133 FSB

    I've got a question about this board. The version I have is an OEM board, I have 1 major problem with it I have tried EVERYTHING i have read in the forums about it and nothing works. I can not get the board to run at the 133 FSB i have a AMD Tbird 1.33Ghz chip with the 266 FSB If i set my Bios to 130 FSB i can run at 1300 Mhz fine but when i go to 133FSB it just sits there and loops the Starting XP screen Here are my sys specs
    AMD 1.33 Tbird
    Thermaltake Valcano 7+ Running on the higest fan speed.
    MSI KT4V Mainboard
    PNY Geforce 4 Ti4200 8X Agp card
    600W Powersupply Robertron I believe
    1 60 Gig Maxtor HD
    1 60 Gig Samsung HD
    1 Aopen 20x CDRW Drive
    1 Stick of Kingston PC2100 256 DDR ram
    1 Stick of IBM PC2100 256 DDR ram
    I have tried it with each stick alone and each stick in different places everytime
    I am Running Windows XP Pro SP1 Installed and useing all the latest Drivers for the Vid, Built in Lan and Audio. Also the Latest Bios update 1.7 nothing seems to make this board run at 133FSB Any help would be greatly thanked.

    OK now I know its not my Heatsink or anything else on my system I know it is this board. I removed Everything execpt 1 hard drive put a old 4 meg PCI video card in and REmounted my HS and CPU and it took me 5 reboots just to get the board to post, after that i set it to the proper 133 FSB and got a NTDRL error changed it back to 100 FSB and it frooze 3 times before finally working After this experence I will Diffently NEVER buy a MSI board this board has been nothing but a headache from the start I will stick by my old faithful ABIT from this day foward..... Anyone wanna buy a slightly used MSI KT4V ??  :D

  • K7N2 deltas mainboards have a problem with usb devices ??

    Ok here is my problem..
    I had installed WinXP Pro with SP1..
    I got a 20 GB USB2.0 disk.i connected it on the both front or rear usb ports.
    When i tried to transfer files to my usb disk or to my PC, in the middle of the copying, i got "Write Delay Failed" error and lost my usb connection..
    I had to plug it out and in again..
    Now, i have an DSL modem..Last night, i was disconnected from internet and my modem's lights gone..I plug it again, no lights..restarted my PC, also completely shutdown Windows XP..Again no lights..
    Then, formatted PC and installed windows 2000 Pr and SP4, until now, my modem worked fine..But USB 2.0 ports are still no use for my usb disk...
    In bios , it's enabled as USB 1.1+2.0..
    I think this K7N2 deltas have a problem with usb 2.0 devices and Win XP Pro..
    Some guys talking about, removing 9th wire earth, but couldn't understand which wire from where ? From mainboard or from usd device's cable ?
    Those cables are fabricated, i think it's impossible ?
    My processor is Athlon 2500+, ram Twinmos 512 DDR 400
    Thanks for reply

    I'm also having this problem. It's happening with my USB flash disk. I was almost buying another one when I tried it with Windows Vista on the same machine and it worked ok, then I tried Arch Linux (with kernel 2.6.30.5) on another machine and got the same error. After that I tried Ubuntu and it worked ok. Seems that Arch's kernel doesn't like my USB flash disk.
    Last edited by esdrasbeleza (2009-09-02 01:16:09)

Maybe you are looking for