Problem with lag in E71 autofocus

The autofocus doesn't seem to be working properly with my E71. I press T and wait for the frame to turn green but after I click the picture there is a lag of about 6-7 seconds and the picture quality is very poor. If I don't use autofocus there is no problem.
Anyone else have the same problem. I have tried a hard reset but it hasn't made a difference. Is this some software issue that will be fixed with firmware or is it a hardware problem? Thanks for any suggestions.

Same problem here. I tried also with 3rd party camera softwares and it does not improve. Thus, the problem is at least at FW level. I won't think it's an hardware problem because in the video mode, capture is ok.
also even though you don't autofocus, if you move the camera while shooting, it freezes again and takes a picture few seconds later..If you set flash mode always on, the flash light goes off randomly.
Let's hope in a FW update.

Similar Messages

  • Problems with lag.

    I am currently having trouble with terrible lag on my phone. Does it need anti-virus? how do i get it and how do i remove all the cookies it might have collected?

    I will do that thanks
    Sent from my MetroPCS 4G Android deviceAnn154 <[email protected]> wrote:>Ann154 Ann154 created the discussion
    >"Re: problems with lag."
    >To view the discussion, visit: https://community.verizonwireless.com/message/834685#834685
    >

  • Problems with lagging?

    I am new to apple as of last month. I recently purchased a new Macbook Pro 13inch 2.26 Intel Core duo, 4gb ram, 320 gb hd. It worked fine for the first month but as of yesterday i noticed a problem with the programs lagging. Its not a serious lag but at times could last 20-40 seconds especially while running Word 2008 and Safari. I have used the disk utilities and have also reset my pram but there has been no change in performance. If someone could walk me through clearing up this issue that would be greatly appreciated. Thanks
    ...I am also running Snow Leopard

    Okay, its been almost 12 hours since I did the Performance Update and my mid 2009 17" uMBP is running like a champ! I have had this problem ever since I got this computer so I have never seen it run as it should and it is like a completely different computer! It is so much faster and smoother without hesitation, I believe that it even shuts down faster. I have now run Quicktime movies, VLC movies, iTunes music, I have streamed audio off the internet and not one hesitation or beach ball. I have also run Safari, Quicktime and iTunes at the same time and it is all running smoothly without any glitches. I wish Apple had been a little more forthcoming about this issue so we didn't have to sit around wondering what the problem was but thank goodness they did the update. I hope it works for everyone that has had the beach ball, hesitation and freeze issues!

  • Problem with lag/synchronization/skipped frame when capture video

    I am trying to capture/record incoming video with audio. I basically clone the incoming datasources and merge them together and save into a file. The file plays fine except there is a synchronization problem between the audio and video. I think the problem is while the audio records fine (lets say 10:00) and video has a few random lags along the way thus decreasing the video time to (9:40) thus combining them will result in 20 seconds of extra audio and no video.... is there a way to fix this or i am capturing the video incorrectly? please help

    You,re nerver tell me if your are a MAC or PC user,
    I am only on a PC. Probably, the majority here are also PC, though there are more Mac-users every day, and there are also quite a few here, who work on both platforms. Because I am on a PC and you are on a Mac, many of my normal suggestions would not apply, so I did not make them.
    I notice in the forum, there is no tech, just stuppid people
    I think that the only stupidity was in my first reply, as I did not read your OP correctly, or comprehend it fully. Harm Millaard, anything BUT a stupid person, corrected me quickly, and I apologized for my errors. "Stuff" happens. I will be stupid again, I assure you. Now, if we omit my error, early on, you have received anything but stupid tips, suggestions and help. The vast majority of the subscribers here, regardless of their native platform, offer great insight and aid to users. They love doing that, or they'd not be here. It's all about trying to help. Now, not everything that they offer will apply, or be helpful. That happens often, when one is trying to remotely troubleshoot a problem. None of us is sitting at your machine. This is not done in real time, but over time. Sometimes a question gets asked twice, because a responder did not catch that it had already been asked, or maybe did not understand the answer.
    firsst i'm a MAc, and FINAL CUT PRO and I am very very happy, is a best and usefull software, I work with Radio Canada, TVA, Big TV communication,  so I do not have time to waste with that.....
    That is probably the best course of action. I think that you will be far happier with FCP, than you ever will with PrPro. Stick with that plan.
    Sorry that your experience here was such a bad one. Just remember that it was not because the subscribers were not trying to help you.
    Good luck,
    Hunt

  • Problems with lagging levels

    when I solo a track in my arrangement, whydo the levels in my mixer start lagging?

    So the problem is that the meter is not falling fast enough? And it "dances" normally once it is not soloed anymore?
    I have not seen this kind of behaviour myself, and it makes no sense either, as soloing a track does not alter CPU load (all the muted tracks are still playing, only silently - so that they sound immediately when you unsolo), but, if the sound does not suffer, well, then I suppose you can learn to live with it, even though it can be frustrating not knowing why things behave as they do.

  • Has anyone solved the problem with " lagging " response when opening nay app ?

    since " upgrading " ( if you can call it that ! ) to IOS7 on iPhone 4, everyone is complaining about the delay when opening any App. At the Genius bar at Apple store they referred to this as " lagging ". After a quick diagnostic of my phone, they suggested a full Restore. Big waste of my time and data. No change whatsoever. I had to go through the full process of syncronizing music and photos and resetting everything.
    I also talked about the new Calendar and especially the Reminders. The new Reminders App is quite simply horrible and no longer attractive and consequently a useless Icon. Even the calendar is labor intensive. I tried to register a future doctor's appointment and the receptionist finally said " Why dont I just call you a day befpre ? ". How Apple managed to make something so simple so complicated is beyond me. The rotary calendar anc clock is a joke.
    It bears repeating, Apple makes too many unnecessary design changes, I dont want to have to invest all this time going to work shops to figure out what they have done with basic apps, especially if its to find out what I already figured out.
    I would however like to know what Apple intends to do about the lagging. I have another 18 months on the iPhone 4.

    No. It was designed to work that way.
    Allan

  • Does anyone a problem with lagging mission control?

    Mission control (expose) on my MBP (8GB RAM) is lagging. Animations of transition between desktop and mission control mode is't continous. First I see animation of desktop (resizing and going to mission control view ), after that windows of appliactions are rearranged (resized and set to mission control view) without animation. Animation from Mission control mode to desktop lagging too
    After instalation everything works fine. I noticed this error yesterday.

    I'm having this exact issue. Late 2007 Santa Rosa MacBook Pro.
    I made a video to show what's going on (the recording slightly exagerates how bad it truly is):
    http://www.youtube.com/watch?v=sYxcmsvMKlY
    The video was made on a 10.6 to 10.7 upgrade install.
    I went in and did a complete wipe + install from a USB drive, and the issue was fixed for about a week before it came back. Is there possibly a .plist file or something we can try deleting to narrow down the issue?

  • I have problem with my phone E71 please help me

    my camare for video call not funtion.. what must i do? just change a camare or the board? pls help me.

    DONT CHANGE ANYTHING
    send it to a nokia care centre
    If  i have helped at all a click on the white star below would be nice thanks.
    Now using the Lumia 1520

  • Can't figure out problem with new PC

    Hi all, I just built my first PC and everything's running pretty well with the exception of some lag and freezing.  My mouse and keyboard sometimes lag behind my true movement.  The mouse does this more often and will lag behind for a second before it catches up to my true movement.  Also, the system has occasionally frozen with the image still on the screen (no blue screens).  Finally, when trying to play music, the audio will skip out every 10 or 12 seconds.  Otherwise, the system is working fine... I've been burning DVDs with it and programs run fine on it.
    I'm thinking that it has something to do with the RAM.  Here is what I've done so far:  I have all the newest drivers from MSI and Sapphire.  I've tried running the system with each of the 512MB modules by themselves.  I've also tried putting them in different DIMM slots.  Any features in the BIOS that may slow the system have been disabled.  The system runs right around 37C for CPU and 42C for the system, so overheating is not an issue.  The RAM isn't getting too hot because the system is slow right from a cold boot.  I've done memtest and it has showed the RAM to be good.  I also ran CPU-Z and the memory specs are below.  Does anyone have suggestions as to the cause of these problems and how to fix them?  Thanks in advance for the help!
    CPU-Z memory specs:
    CPU-Z version 1.22
    Memory Modules Serial Presence Detect (SPD)
    Module #1
    General
    Memory type      DDR-SDRAM
    Manufacturer (ID)   Kingston (7F98000000000000)
    Size         512 MBytes
    Max bandwidth      PC3200 (200 MHz)
    Part number      K
    Attributes
    Number of banks      2
    Data width      64 bits
    Correction      None
    Registered      no
    Buffered      no
    Timings table
    Frequency (MHz)      133   166   200   
    CAS#         2.0   2.5   3.0   
    RAS# to CAS# delay   2   3   3   
    RAS# Precharge      2   3   3   
    TRAS#         6   7   8   
    Module #2
    General
    Memory type      DDR-SDRAM
    Manufacturer (ID)   Infineon (C1494E46494E454F)
    Size         512 MBytes
    Max bandwidth      PC3200 (200 MHz)
    Part number      64D64320GU5B      
    Attributes
    Number of banks      2
    Data width      64 bits
    Correction      None
    Registered      no
    Buffered      no
    Timings table
    Frequency (MHz)      133   166   200   
    CAS#         2.0   2.5   3.0   
    RAS# to CAS# delay   2   3   3   
    RAS# Precharge      2   3   3   
    TRAS#         6   7   8

    I now have all my programs loaded back on and all the drivers loaded and still have no problems with lagging or audio skipping.  I did not install any of the Promise drivers this time.  All I installed was the via driver necessary for installing windows xp at the "F6" menu.  I also did not install all of the MSI utilities, etc. this time.  SO all I can think of is that the problem lied in the promise drivers or some of the MSI utilities.  The PS is running all of my drives fine as of right now.  Regardless, I'm up and running good, so I'm happy.  I hope this helps someone else.
    Also... has anyone had problems with the Realtek ethernet adapter?  My comp. gives me a "network location no longer available" error every time I try to copy files over the network from my other computer.  I haven't seen anyone else with this error or found how to fix it.  I have file sharing enabled, the windows firewall is not on, TCP/IP is installed along with client for Microsoft networks.  They're all in the same workgroup also.  I can connect to the Internet and the connection seems to be set up properly.  I think that covers everything I've checked...

  • I have an ipad mini 1st gen 64 gb (wifi only) and i have problem with some of my apps. These apps have lags when you play with them for a few seconds the apps are having lags are call of duty strike team, gta San Andreas and nfs most wanted.pleas help me

    I have an ipad mini 1st gen 64 gb (wifi only) and i have problem with some of my apps. These apps have lags when you play with them for a few seconds the apps are having lags are call of duty strike team, gta San Andreas and nfs most wanted.pleas help me

    I'm going to guess videos buffer for a while also...
    Two possibilities, one is you should close apps on the iPad, the other is your internet speed is not able to handle the demands of a high speed device.
    To close apps:   Double click home button, swipe up to close the apps.
    To solve internet problem, contact your provider.   Basic internet is not enough for video games and movies.   Your router may be old and slow.

  • E71 - Problem with Flashlite 3

    Hi, I have this unsual problem with the flashlite. For E71 - it is suppose to be integrated with the web browser. It worked well for the first couple of days - however after that when I tried to watch clips from YouTube - the video did managed to load. instead - the portion where the video is suppose to be was left empty.
    I googled and found that e90 has similar problem from www.allaboutsymbian.com. Steve from AAS suggested for users to format their phone - ie *#7370# for flashlite to work properly again. I formatted my phone at least 3 times - but still in vain.
    Do any of you have similar problem? Any solution for that?

    I have a similar problem, but when I put those files from a sd card to a phone memory, they show up. Otherwise I have to browse the phone to get those files

  • E71 problem with BT stereo headphones

    Hello!
    I have got a E71 and I have a problem with the BT stereo headphones (Model Clip IIs of I-TECH I have some time with other phones and I have never given any problem) I use to listen to MP3s on my SD, and the fact that at some point the sound begins to 'stutter', that is no longer playing but continues to sobs, the sound comes and goes ... it does not always but sometimes, and sometimes no But often jumps out the problem and I have to close the player, wait a while 'and then restart it. Given that the first thing I did was upgrade to the latest version noBrand FW 110.07.127 RM-436 09/10/2008, but has not resolved ...

    I think this is due to the phone's CPU getting overloaded by having to recompress the audio stream for A2DP (the BT profile used for stereo). Avoid running any other apps when you're listening to music and see what happens.
    Sanjay Mehta
    Motorola "Brickphone" circa 1996, Alcatel One Touch, Ericsson R380, Sony Ericsson T220, Sony Ericsson T630, Nokia E50, Nokia E61i, Nokia 9300i, Nokia E71,Nokia X6, Google Nexus S, iPhone 4S

  • Has anybody had a problem with the mouse cursor lagging when navigating the drop down menus? this only started happening after a re-install. it only occurs in Photoshop elements 13 in the  photo editing section,and no other application. My mouse drivers a

    Has anybody had a problem with the mouse cursor lagging when navigating the drop down menus? this only started happening after a re-install. it only occurs in Photoshop elements 13 in the  photo editing section,and no other application. My mouse drivers are up to date.Any help or advice would be most welcome.

    Good day!
    Please post Photoshop Elements related queries over at
    http://forums.adobe.com/community/photoshop_elements
    and please read this (in particular the section titled "Supply pertinent information for quicker answers"):
    http://blogs.adobe.com/crawlspace/2012/07/photoshop-basic-troubleshooting-steps-to-fix-mos t-issues.html
    Regards,
    Pfaffenbichler

  • Brush pressure and lag problem with CS4

    I've been having a huge problem with Photoshop CS4 and the brushes. Whenever I go to brush, the pressure will turn off and on randomly with each stroke, and it lags horribly. I've installed CS4 on two computers with Windows 7, and both have this problem, but my old computer which had Vista was perfectly fine. I've tried downloading new versions of CS4, turning the OpenGL on and off, updating the GPU, downloading the Windows 7 tablet driver (that made it worst), and a bunch of other things. Nothing has worked, and this problem has been going on for two months. I'm starting to think the only way to fix this problem is by switching back to Vista. Can anyone please help me solve this? Thank you.
    My computer is an HP that runs on Windows 7, my Tablet is a Wacom Intuos3, and I have Photoshop CS4 Extended 11.0.2

    Others have reported that completely removing the tablet driver(s) first, then installing the very latest from the Wacom web site have made things work.
    Good luck.
    -Noel

  • E71 - Problems with dictonary and languages instal...

    Hi to everybody!
    I have a problem with my dictonary but I can't find a solution.
    My firmware version is 110.07.127 09-10-2008 rm-346 nokia e71-1 (17).
    My default pre-installed language is English.
    I have installed 2 languages in the memory card: Italian and Turkish.
    At this point, I have tried to install (in the memory card) another language (Croatian) but at the end of the language installation the dictionary forced me to remove one language.
    I have also tried to uninstall languages by Application Manager with no success...when I have tried to reinstall languages, I have got the same message.
    I can't find a solution to this problem.
    Can you help me?
    Thanks a lot in advance.
    Bye bye.

    I'm very disappointed
    I can't believe that E71 only allows the installation of max 3 languages!

Maybe you are looking for