Problem with LAN onboard

I have problem with MSI 875P NEO. I am upgrade a BIOS and then i dont disable LAN onboard. Help me!!!!

Dear friend,
I, likewise borgunit, still could find out in anyways whether you want to have LAN enable or disable... Maybe you should follow Danny's instruction to find out whether that is what you are looking for .

Similar Messages

V570 problem with Intel onboard driver on Windows 7 Pro 64 bit

Hello Everyone,
I recently installed Windows 7 Pro 64 bit on my Lenovo v570. I downloaded the drivers from the support page and I have a strange problem with the onboard graphics driver "Intel Onboard Graphics Driver for Microsoft Windows 7 (64-bit) - Lenovo B470, B570, V370, V470, V570" in the drivers section.
Installation seems fine, but after restart, the system fails to boot and goes into boot recovery mode, where I get a message saying that booting failed due to a bad driver and the only actual option I have to boot up is to go back to a previous restore point. I tried installing the Nvidia driver for Windows 7, but it says that I need to install an Intel driver first, which is the one that gives me the blue screen when booting. I have also tried installing both drivers without a restart between both installations, but that didn't help.
I am wondering if anyone in the community has seen something similar. Any advice, information or assistance will be highly appreciated. Thank you very much in advance for your time.
Best regards,
Moe.
Solved!
Go to Solution.

Welcome to the Lenovo Community !
Check out the link I have posted below for video driver installation problems on your model. The suggestions offered have worked for others.
http://forums.lenovo.com/t5/Lenovo-C-E-K-M-N-and-V-Series/V570-video-drivers-don-t-work-with-Windows...
Owner & Operator of the following:
● Lenovo Ideapad Z570 w/ Win 7 & Win 8.1 Dual Boot ● Lenovo Yoga 3 Pro w/ Windows 8.1 ● Toshiba A75-S206 w/ Win 7
● IBM Thinkpad T-23 w/ Win XP ● IBM Thinkpad T-22 w/ Win XP • As well as multiple desktops dual/triple booting XP, Vista and Win 7.
★ Find a post helpful? Thank that member by clicking on the ☆Star☆ to the left awarding them a Kudo.
★ Posting a problem and a reply is helpful and it answers your question, please mark it as an "Accepted Solution"
★ I'm not a Lenovo employee, just a volunteer geek who likes to help folks. Enjoy your time here, pay it forward by helping others !
★ Sorry, I don't answer questions via Private Messages. Posting in the appropriate forum is the best way to get assistance.

Problems with LAN RJ45 Ethernet link on Tecra A8-PTA83E

I experienced some problems with the on-board Intel PRO/1000 PL Ethernet adapter. The adapter in most cases works fine: it connects normally in 100 or 1000Mbps - full duplex - speed, depends on wich internetworking devices attached, and the link doesn't present any issues.
But, in some cases, with several Eth devices, the adapter doesn't estabilish the link at all, the green LED on the right (Link?) blinks continuosly with a period of 2 sec. (0.5" on - 1.5" off) and the yellow on the left (Traffic?) remain always off. At the other side of the Cat5e cable, the device (now a router Linksys WAG325N) signs no connection. It's NO cable problem.
Windows (XP Pro, SP2) sometimes reports in the little icon of the LAN adapter driver on the traybar a connection established at various speed (often 100Mbps, but sometimes 1000Mbps!) but very quickly it returns in "cable disconnected" status.
I've tried to upgrade the drivers directly from Intel Support pages because Toshiba's Support doesn't recognize my laptop (!!!) , and because in origin I've made a downgrade to XP (I'm sorry, but I do NOT intend to use the original MS Vista!), but nothing change.
The only way to establish a connection that I found is to manually reduce the speed (10Mbps - full duplex) of the link by the Advanced Settings of the XP driver. In this case all works, but a low speed.
Can anyone help me? Someone has already noticed this problem?
Thanks!
Paolo

Hi
Im not quite sure if its NOT an cable issue.
Did you try to connect both devices using a crossover cable (cross wiring)
There are three different kinds of crosscable:
- 10BASE-T- und 100BASE-TX-Ethernet
- 100BASE-T4-Ethernet
- 1000BASE-T-Ethernet
The difference is usage of crossed wire pairs.
At the other hand the usage of crossover cables is not necessary if you connect a router or switch device.
But in case you would like to connect two notebooks, the crossover cable is required.

Cisco ISE 1.2 - Problem with Device Onboarding of internal users using AD Credentials

Dear experts,
We have implemented ISE 1.2 with WLC 7.5 in our organization. We are using Device Onboarding by letting the users enter their AD Username and Passowrd on Guest portal which then redirects them to device registration portal where they simply register their device and they get internet access.
The problem is that some users are unable to authenticate using this portal while some can successfully authenticate and register their devices. All users are of the same group in AD. Also, we have enabled this check on two places. One is when users connects to the SSID where the security WPA2-Enterprise uses 802.1x and asks for AD username password. The other is on the portal.
All users are able to connect to the SSID using their AD credentials. However, 30% of the users are not being authenticated when they are redirected to the Guest portal for device registration. Also, it gives no error or event on either ISE or on the mobille device. When the users enters their credentials, the same guest portal page comes back blank with no errors or logs anywhere.
Can someone guide me if there is some configuration mistake that I may have done or have someone faced this same issue and were/weren't able to resolve it.
Thanks in advance.
Jay

Our problem got solved. It was related to a few user accounts in AD. Usually any authentication on AD User Account is carried out using the User ID. However, during Web Authentication, Login ID/Name is also checked by ISE and should be same as User ID.
The problem you are facing might also related be to AD since we had the similar issue. try to check this on a laptop as the mobile portal gives no error if the user is unknown or invalid. Also, you can enable logs for web authentication which are off by default. It will give you a pretty good idea where the problem lies. And yeah, do not keep the web authentications log on for long, it can hang your ISE.
Anyways, thanks for all the support.

Various audio problems with the onboard speakers but not the headphones.

The little volume wheel is connected to a variable resistor, which is soldered to the motherboard via 7 pins. when the wheel loosens up, or the pins loosen up, the onboard speakers get flaky or just don't work. We've been seeing this type of problem for a while now, and just thought that the general public should know. Either replace the motherboard, or the volume controller, or wiggle and jiggle the wheel when it gives problems. good luck all, and i hope this little tid-bit helps out.
Kudos for Linux and all freeware!!

Hi,
Try the following.
First, download and reinstall the Chipset driver on the following link.
Chipset Driver - Windows 8
When the reinstallation has completed, restart the notebook.
When windows has reloaded, download the IDT Audio installer on the link below and save it to your Downloads folder.
IDT Audio Installer - Windows 8.
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When complete, shut down the notebook, unplug the AC Adapter and then remove the battery. Hold down the Power button for 30 seconds. Re-insert the battery and plug in the AC Adapter.
Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu. Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter. Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
Let Windows fully load - it will automatically load an audio driver, but just let this complete. Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, right click the speaker icon in the Taskbar and select Playback Devices. Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio through headphones.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

CE560 and problems with Websense onboard

I am testing Websense on the local CE to filter URL's. I recently had to move it from a test environment to a production environment and in the process had to change IP addresses. I used the Websense ChangeIP utility to do this but now when I try to access the CE with Websense manager I get the following error: Cannot read configuration data from /EIMServer/Global/OldConfig/K2097153. Error 1100021762. In the config.xml file on the CE, there is no K2097153 listed under the OldConfig section. Also, when I go to the CE Web GUI the Websense server says it cannot connect to openserver on localhost.
I have spoken to Websense and they have not helped me at all at this point.
Any help on this problem woud be greatly appreciated.

Resolved. Copied a configuration file from a working CE560 and replaced the IP's in the configuration file with the IP of the new CE and WebSense is now working.

Problems with BYOD onboarding with ISE 1.3 Internal CA

This implementation is leveraging the ISE 1.3 internal CA to enroll certs to authenticated BYOD users. The authentication/authorization profiles and policies are configured for wireless supplicant provisioning for AD authenticated IOS and Android devices.
•             When the test BYOD user with AD credentials tries to log in, they get redirected to the ISE BYOD provisioning portal.
•             They get to step 3 and successfully install the ISE certificate.
•             They then get a prompt to install the profile service (enroll an identity cert and load the wireless profile). This attempts to install for about 30 seconds and then fails with a message – ‘Profile installation Failed’ The request timed out.
The only thing I noticed that may possibly be an issue is that they are using a wild card cert signed by digicert for the ISE identity cert. Or maybe something else needs to allowed in the provisioning ACL?
I appreciate any assistance on this.

A few questions here:
1. Is this for wired or wireless BYOD
2. What version of ISE and Controller / Switch are you running
3. Post a screen shot of the Client Provisioning ACL
4. Post a screenshot of your AAA policies in ISE
The wildcard cert should not be OK as that will only be used for the HTTPs portion of the request while the EAP session would be based on the ISE CA cert.
Thank you for rating helpful posts!

H55M-E23 Problems with Onboard Realtek Gigabit NIC

I just finished a new build HTPC using the H55M-E23 and I'm having problems with the onboard Realtek Gigabit LAN controller.
System specs are: OS is Windows 7 - 64 bit. Intel i3-540 @ 3.0 GHz, 4GB RAM, 60GB SSD. NVIDIA GT 430 video card w/ 1MB RAM is only add in card. 300 Watt Power Supply. NVIDIA card is the primary video card and is set up that way in BIOS.
Everything installed fine and seems to work great, except that when I watch HD video, stored on a local NAS on my home network (all gigabit, including cables), about half the time, the Realtek controller will drop to about 10 MBPS, which causes the video to stutter and lockup. The video normally streams across the network at about 23 MBPS max. All other PC's on my network play these videos (home movies) no problem. CPU utilization on the MSI board is only about 5% and the video card's GPU utilization maxes out at only about 65% when the videos are streaming properly. Also, I can copy the video directly to the SSD on this HTPC and the video plays fine. So I think the rest of the hardware on the HTPC is sufficient to do what I'm trying to do. The truly annoying thing is that sometimes it works and sometimes it doesn't work.
All the latest drivers have been installed for the motherboard, video card, and Realtek NIC (trying both from MSI's website and Realtek's with the same result). The Windows installation is very clean. I've wiped the SSD twice and done a fresh Windows install and tried this immediately after the Windows install has competed and all drivers installed and again after Windows has completed all updates and I get the same result each time. I've tried several "slow network connection" solutions from Google and none so far have worked.
For anyone old like me, this acts like an IRQ conflict from back in the early days of Windows. Of course Windows 7 doesn't let you mess with IRQ's anymore, at least that I can find. BTW, Device Manager lists the IRQ for the Realtek NIC as "-2", which is very odd to me, but I'm no expert. I'm at the point now of disabling the onboard Realtek LAN and buying a cheap NIC to see if that works, but wanted to try to see if MSI has any suggestions or should I RMA the board? Any suggestions would be greatly appreciated.
Thanks,
Ben

Yeah, I agree that I'll need to upgrade the PSU anyway. 300W is marginal at best for this setup. I would have probably been ok without the add in video card, but the GT 430 really makes a difference compared to the built-in graphics of the i3 and the card was so inexpensive that it was a no-brainer. I may try to take out the GT 430 just to see if the Realtek NIC behaves better, but I think long term I'll just get a cheap PCI-e NIC and that should fix things.
I would normally suspect the SSD as well, but I get the stuttering when I'm using the network streaming. The videos play fine when running directly off of the SSD. I know the SSD could still cause issues, but everything just seems to point to the Realtek chip. Honestly, I really think it's a driver / setting issue and not a bad piece of hardware, although I could be wrong.
If anyone has any other ideas, please keep 'em coming. In the meantime, I'll try a new NIC, etc and let you know what I find.
Thanks,
Ben

Network problems with MSI 790FX-GD70

Hi All
I have a problem with the onboard network cards.
It only works the first time from cold boot (when the powercable is completly disconnected from the PC, and LAN cable disconnected, turn on PC and then connect LAN cable)
If I shut it it down or restart the computer, then the LAN card disconnects, eg no lights active on either the pc nor the router. But if I do the procedure described above everything works ok again.
Same problem occours with both LAN ports.
My system:
MSI 790FX-GD70
AMD 720BE
4GB Corsair 1600mhz DDR3
2x Asus HD4850 Crossfire
2x Samsung t166 320GB HD
Windows XP SP3
Tried 3 different routers but all with the same error. So everything points towards the motherboard.
Please help.
PearsonDK

Quote from: Fredrik on 09-August-09, 06:19:22
If the LAN-card is disconnected I wonder if the LAN-card is "present" at all. Check Deceive Manager. Please give some PSU info. Problematic booting and falling out devices...
Also, please, what is your BIOS Version? Make sure its 1.4 .
Drivers - have you downloaded the latest ones from MSI's site and installed them for the LAN card?
Man.. is it me, or have there been like 6-7 people coming up with similar LAN issues on this board? I've never known an onboard NIC to have issues.

Driver problems with a K7N415 Pro

I had to reload WinXP on my computer with a MSI K7N415 Pro motherboard and I am having a problem loading the drivers for the following imbedded hardware:
Ethernet controller
Audio codec interface
MCP audio processing unit
PCI system management
PCI standard RAM controller
I installed the XP drivers from the MSI CD/ROM, but the drivers are not being detected at restart. I have tried to update the drivers from device manager, but get the following error:
There was a problem installing this hardware
(device name)
An error occurred during the installation of the device
Access denied
Does any one know what I can do?

Hi,
When you say you installed the XP drivers, was it an automatic install (i.e did you click on the CD and it installed all drivers at once). I had initial problems with this multi-driver install approach when I first started using XP and the included MSI driver CD.
If this is the case then I think you could install them (the drivers) individually (this helped me). Firstly, you'll have to remove any drivers that have been installed (for the nForce embedded devices) and uninstall any of the nforce devices from Control Panel > System > Hardware (Tab)> Device Manager.
On reboot, wait for Windows to "Detect new hardware" but instead of using the "Automatic Search for drivers" manually point the install program to the directory where the (relevant) driver resides (on your MSI Driver CD). It may be a good idea, to only install your Ethernet drivers and then see if you can access the net - then, if you are able - you can download the nVidia unified drivers and install the rest.
BTW, you haven't got anything "active" attached to your LAN port have you (cable modem etc.)? If so, unplug it before installing drivers.
As I mentioned earlier, I have had problems with XP and MSI drivers but as I'm not using the same MoBo as you, I thought them unrelated - at this point though, I'm convinced you've a driver problem and it's not hardware related (though I could be wrong - it wouldn't be the first time). I originally had problems with my onboard sound and I was unable to install drivers - after much faffing about though, I managed it in the end.
My apologies if you've tried any of the above before.
Axel :D

Kt4v possible problem with bios 1.8 and hd

Any Idea anyone with this one.
system running well till the other day when hd went very slow even after defrag, install bios 1.8 and reset the bios and adjusting it for my setup. Come to check my harddrive with maxtor powerdiag 3.04 and could not find the drive or any other drives connected. In the bios setup the drive is present. I removed all drives, cdroms, etc except the maxtor main hd and tried again with the same result. After placing in an ata100 controller card in to a spare pci slot and plugged the hd on to it, that the software sees the drive. The test finished and show the HD to be fine.
The question is do I have a problem with the onboard contoller or with the new bios or both.
When I first got this MB I did the same test with the original bios and the hd connected to the MB controller and the software had no problem seeing that and other drive connected.
my pc
6712 mb kt4v
athlon 2700+
ti4200 graphics card
2 off ddr333 512Mb memory
floppy drive
sony cdrw
system software windows xp pro
hard drive maxtor d740x-6l 60Gb ata133

I'll stick with the V1.10, but I'd fell better if MSI showed me they actively update their systems by releasing updated BIOS files from time to time.
I can't sell a 15000$ storage system that doesn't recognise the CPUs installed. The customer would laugh and tell me to come back with a supported system.
Isn't this a VERY valid reason for wanting updates? Even if it only is an updated CPU list?
The only reason I tried this MSI board is that it was the only one available with my retailer at the time I bought it with 3 PCI-X 100Mhz slots. Maybe I should go with a Tyan Thunder next time. Tyan at least show some activity.

Ethernet connector problem with T60

Hi, we have a ThinkPad T60 (2007-72U) and it got a problem with the onboard ethernet jack. The card is working perfectly when connected through the dock, so the problem is specific to the onboard jack. Is there a way to replace only that part or the whole motherboard have to be replaced? According to the system service parts page I've found it seems to be the later option, but I wan't to make sure I'm not missing something. Also, can someone point me where I could find on-site support for this type of problem in Quebec, Canada.
Thanks

I could fix no on board ethernet problem - needs SMD desoldering/soldering skills.
PROBLEM::
1. wireless network ok.
2. docking station wired ethernet ok.
3. on board ethernet - not listed in devices -- bios setup - hide - boot - enable - boot - now shown in device list
now onboard ethernet - tx packets ok, rx packets 0.
the problem was shorted ESD protection diode array near the on board ethernet jack.
part number (for T60P laptop) CDSOT23-SRV05-4CT-ND at digikey.com
SOLUTION:
removed the 6 legged ESD/TVS diode array (CDSOT23-SRV05-4CT-ND) from motherboard - rx packets ok - ethernet ok now.
replced it for continued protection from ESD.
hope this helps -- I fixed one more laptop - T60 - same issue - so I think its a common problem

Problem with Jabber and file transfers WAN - LAN-Users - a solution!

Hi,
I read a lot of messages about problems with file transfers between iChat-Users, if one (or both) are behind a NAT.
I had this problem to and found an easy solution:
My situation
iChat-Server behind a Netgear ProSafe FireWall. I opened the needed Ports including Port 7777 (the Port for the iChat-proxy (proxy65).
The iChat-Server is configured to host the domain "server.ourdomain.com" (as an example).
This address can be reached from the LAN and also from the WAN-side.
From the LAN-side the DNS redirects to 192.168.1.1, from the WAN this domain redirects to our official IP-address (the WAN-IP of the FireWall).
I tried nearly all kinds of mentioned solutions, but nothing helped.
The really easy solution is: I just added our official IP to the "Hosted Domains" in the iChat-section of Server-Admin.
After that change, the transfers are made via the proxy65 of iChat-Server. The transfers are shown in the log /private/var/jabberd/log/proxy65.log.
I think, that the other posters who also have this kind of problem are working in a similar setup (domain name of server is used from the LAN AND the WAN-side with different IP-addresses (LAN-IP & WAN-IP).
This solution will only work, if the WAN-IP is a fixed address.
svenc

Until the introduction of file promises in AIR Athena, it has never been possible to drag remote files out of an AIR application.
You could refer to the http://www.adobe.com/devnet/air/flex/articles/using_file_promises.html
Hope this is helpful. Please let me know if I could help more.

Problem with Dockingstation Type 2504 and R60 LAN Performance

Hello,
we have a smal problem with a lenovo dockingstation type 2504 and a r60 laptop.
Made some performance test for oure fileserver.
Found out, if i use dockingsstation, i get poor performance.
If i use the r60 without dockingstation, lan performance is realy good.
Some idea why?
How could it be?
Performance profile is max.
Use battrie in r60, dockingstation with power supply.
Big thanks

Ok, so I was able to video chat with Defcom last night by turning on my firewall and also by changing iChat/AIM to logon through port 334. I still cannot video chat with appleutest01. Any other ideas?

Lan, NAS, SMB problem with Lion

Hello I have 2 mac on which I installed Lion, unfortunately I have some serious problems with my LAN.
I have 2 NAS which I can not log in, one is STORA of the Netgear (which I hope will update) and an older (a FISC CHD by StoreTech I do not think the update)
... how can I do with it? Do not tell me that I must throw in a stupid update ... it's a NAS RAID 5 with 4 drives ...
I also have another problem with my multifunction printer Kyocera 250Ci, in practice I always use the network scanner so that I would send the files to inside of the machine by entering the IP address and shared folder ... without making any changes, after the installation of LION, the scanner tells me I can no longer find the way, I checked everything and rebuilt 100 times ... but nothing!! has the machine 1 month of life and costs a few thousand of € .... also this is absurd!
Someone can help me to find a way to use my device? SMB protocoll is the same in SL and Lion?
Tank's a lot!!

Hi everybody,
same configuration for me (exempt itunes 10.5.2) and same problem for me. I remember a time when it worked, all of a sudden, it stops. If I click on the shared library, the contents is displayed for a second and afterwards iTunes jumps back to main library. So, you are not alone, checked it also with a different user account, no change.
Keep you informed,
Thomas

Problem with LAN onboard

Similar Messages

Maybe you are looking for