Problem with logic pro 7 & jam pack
Hello,
first sorry me for my english....but I need help
I'v a big problem with my jam pack.
1/
when I want to hear some loop with the navigator loop, the sound is deformed like with a tremolo and a reverb...
when I take a midi loop and I put it on my arrangement the sounds is ok
It makes the research of loop very difficult(it does'nt sound right).
2/
I've the same problem in the navigator loop with the audio loop.
But when I put it in my arrangement the sound isn't ok (deformed, tremolo...)
On the other hand the deformation disappears when I put a faster tempo
(around 100 bpm)
Precision; my arrangement is at 50 bpm
Thank you so much for your help
g5 Mac OS X (10.4.9)
hi, you are play the loop back too slow.
there's a limit to how far a loop may be slowed down.
apple loops are generally played back via the last audio channel available, whether you are using in your song or not.
check this channel to see if it has effects inserted or is using the bus sends. if so, switch these off to hear your loops properly.
DR9
Similar Messages
-
Problem with Logic Pro and Soft eLicenser on Mountain Lion?
Hi!
I have a bunch of Arturia synths, which requires the Soft eLicenser to work. This has always worked great with Lion, never any problems with eLicenser (never had to open it etc.)
Now - I upgraded to Mountain Lion, and tested my synths to make sure everything was OK, experienced a bunch of problems, and did a full recovery to clean Mountain Lion.
After installing the Arturia synths, and adding my licenses, I installed Logic. Everything worked fine!
BUT!
When I closed an Arturia synth within Logic, or closed Logic after running a project with one of these synths, I couldn't reopen any of these synths within Logic afterwards - In fact, I couldn't open the stand-alones either! And when I tried to open the eLicenser Control Center, it would just say "Reading eLicensers" forever. After a reboot, everything is OK.
I can open and close eLicenser Control Center and standalone synths as many times as I want, as long as I don't open Logic, and then Arturia synths as an AU in Logic.
I found a workaround: Open the eLicenser Control Center, and let in run in the background (cmd+H), and then open Logic. Then I could open Arturia synths and close them, close Logic and reopen etc. without any problems at all. NO PROBLEMS.
Until I close the eLicenser Control Center, then I have to reboot to be able to start it again.
I hope you understand what I mean here. It's a bit hard to explain.
In short terms: Logic makes Soft eLicenser crash when a eLicenser synth has been opened as an AU.
The same problem is when scanning the AU with AU manager. eLicenser window should be open before scanning.
Does ANYBODY have the same problems? Can anyone who has these applications test it out?So it definitely seems to be a issue with Logic.
I can't force this error in 10.7.X no matter how hard I try, but in 10.8.2 it's definitely Logic messing things up.
Could it be auvaltool which has a bug? Or is that only run with AU manager on validation?
Hopefully this discussion can get some attention, and maybe it could be corrected. I guess a lot of Logic Pro users also has eLicenser Control Center for validation of their products. -
Problem with Logic Pro 7 Academic Version
I've been using my academic version of logic pro 7 for about a year, and just recently it hasn't been starting up the way it used to. Usually when it launches, it says logic pro 7: academic version. But now it just says logic pro 7 and tries to run it as a one day trial of the retail version. I tried to get help over the phone but they were saying that they can't help me troubleshoot because they can only help out with logic studio. basically, they say to just reinstall it and if still have problems post it on this discussion. so here i am after the reinstall with the problem still occurring. some help please?
i just updated my xskey from the xskey updater in the utilities folder and it works now.
-
Evolution MK449C Mod Wheel problem with Logic Pro/VSL Performance Tool
I'm using the latest version of Logic Pro on a new Intel Mac Pro. My controller keyboard is the Evolution MK449C, connected via a USB cable.
When using a Logic Audio Instrument assigned to the ESX Sampler Plug-in (running various samples, mostly from the Vienna Symphonic Library,) Logic's Transport Window doesn't register any modulation information generated from my keyboard.
As the VSL Performance Tool relies heavily on the Mod Wheel info to effect the sounds, I'm at a bit of a loss to spot the solution. When I assign a different conroller to the Mod Wheel, i.e. volume, pan, pitch bend, etc., I can see the info in the Transport Window with no problem, so I know the wheel itself is working okay.
Has either Logic or the ESX got some kind of controller filter, - maybe I've accidently turned something on that cuts out any incoming modulation. Can anyone help?
Thanks
Mac Pro Mac OS X (10.4.8)It's good to know someone else is having a similar problem (if one can call that good!)
I've been poking around and I've also noticed this: If I create a cello part in Garageband, articulation works everytime I open it. If I take that Garageband song and open it in Logic, articulation still works everytime I open it. The Logic file in this instance is saved as a "Logic Song." I don't know how to tell, but I'm assuming the Logic song is drawing it's sound files from the Garageband song (I don't know how to check that).
However, if I save the newly created Logic song as a project - with all sound files being copied to folders within a master project folder - articulation does not work when I reopen the file.
Strange. And frustrating.
MacPro 2.66 2GB RAM & Powerbook 400mhz "Pismo" Mac OS X (10.4.7) -
Presonus Faderport problem with Logic Pro 7 running Snow Leopard
I've been been using Tiger to run Logic Pro 7 without any problems for the past few years. I've held out on upgrading to Snow Leopard since everything worked so nicely, but I finally gave in and loaded 10.6.6. Logic Pro 7 seems to be okay except for my Faderport control surface functionality. I upgraded to the newest FP firmware, and Logic 7 recognizes the FP, but it doesn't work. When I open a Logic project I get a pop up dialog box that says:
Module file "Faderport" is too new and cannot be used with this version of Logic control surfaces. Please get an update of the Logic control surface application file. I also get another dialog box that says: "Loading Module Faderport..." But nothing happens.
I'd appreciate any and all ideas on how I might deal with this. Thanks!Hi,
I'm getting this message since updating the Faderport Firmware. I'm using Logic 7 in Tiger still.
How did you fix the install pref? -
A Problem with Logic Pro 7 Crashing
Appreciate any help.
I'm running Logic Pro 7.2.0 (academic - no upgrades) on a Mac Pro w/3GB. I use an M-Audio Firewire 410.
Logic runs perfectly...AFTER the audio has been played successfully once. Before that, when I open a song and press Play, it's about 50% likely I'll get, "The program Logic has quit unexpectedly" - occasionally, this is preceeded by "Core Audio too slow" or "1 or more Files in Use."
I'll tried deleting preferences, etc. Should I re-install the program? Can this really be the solution, considering it works perfectly once the song has successfully started playing? (If I open a new song and close the 1st, I'm back to 50% likelihood of a crash.
It very seldom crashes under any conditions other than immediately trying to play a song that has just been opened. (Is this the crucial clue?)
Oh, and I'm running 10.4.10. Everything is brand new. Arghhh!
Thanks for any help you can give.As already pointed out, 10.4.10 is not great on intel machines for audio. The latest driver for the M-Audio Firewire 410 is better than most USB ones on 10.4.10, but the lack of Logic upgrades does mean it is of an earlier time than 10.4.10 and I would try to do something about that first.
It may well be to do with the core audio system, and you may get different results if you create an aggregate device in Audio Midi Setup, including both built in devices and the Firewire 410 and see if that helps!
Karn. -
Audio Unit Problem with Logic Pro and Mainstage
When I go to launch my apps, both Logic Pro and Mainstage get stuck loading an AppleAUspeechsynthesis or something along those lines. It never makes it past there and I either have to force quit or it quits itself. I can press control while launching Logic Pro, but then I only get basic MIDI. I just tried an archive and install and I'm in the process of reinstalling Logic Pro right now. Does anyone know what might be causing this?
I just tried pasting my crash report. It seems like it is too long to post?
-
Im having problems with logic pro 9 working with native instruments it always quits unexpectedly
Interval Since Last Panic Report: 79051 sec
Panics Since Last Report: 6
Anonymous UUID: 84387C31-EAF1-E5E2-8362-4FA69C1C8FCD
Mon Mar 11 19:34:04 2013
panic(cpu 1 caller 0xffffff80062b7bd5): Kernel trap at 0xffffff80066520fc, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0xffffff8166f93ad8, CR3: 0x0000000008c6c000, CR4: 0x00000000000606e0
RAX: 0x0000000000000000, RBX: 0xffffff8023fb3100, RCX: 0x0000000000000c80, RDX: 0x000000000000ec80
RSP: 0xffffff8166fa3ab0, RBP: 0xffffff8166fa3ba0, RSI: 0x00000000000582eb, RDI: 0xffffff8023fb3030
R8: 0xffffff8166fa3ad0, R9: 0x0000000000000c80, R10: 0xffffff8023fb3030, R11: 0xffffff8023fb3000
R12: 0x0000000000000000, R13: 0x0000000000001380, R14: 0x0000000000000000, R15: 0x0000000000000800
RFL: 0x0000000000010246, RIP: 0xffffff80066520fc, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0xffffff8166f93ad8, Error code: 0x0000000000000000, Fault CPU: 0x1
Backtrace (CPU 1), Frame : Return Address
0xffffff8166fa3750 : 0xffffff800621d626
0xffffff8166fa37c0 : 0xffffff80062b7bd5
0xffffff8166fa3990 : 0xffffff80062ce4ed
0xffffff8166fa39b0 : 0xffffff80066520fc
0xffffff8166fa3ba0 : 0xffffff800665147a
0xffffff8166fa3be0 : 0xffffff7f869326ea
0xffffff8166fa3c40 : 0xffffff7f8692bf06
0xffffff8166fa3c80 : 0xffffff7f868cb978
0xffffff8166fa3d50 : 0xffffff7f86be75ea
0xffffff8166fa3e10 : 0xffffff7f86be8cff
0xffffff8166fa3eb0 : 0xffffff7f86be8d3f
0xffffff8166fa3ed0 : 0xffffff7f86be2f1b
0xffffff8166fa3ef0 : 0xffffff80066472a8
0xffffff8166fa3f30 : 0xffffff8006645daa
0xffffff8166fa3f80 : 0xffffff8006645ed9
0xffffff8166fa3fb0 : 0xffffff80062b26b7
Kernel Extensions in backtrace:
com.apple.iokit.IOUSBFamily(5.4)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffffff 7f868c8000->0xffffff7f8691efff
dependency: com.apple.iokit.IOPCIFamily(2.7.2)[B1B77B26-7984-302F-BA8E-544DD3D75E73]@0xffff ff7f86850000
com.apple.driver.AppleUSBEHCI(5.4)[E4CA8E89-01B4-3A74-A46F-31A917AD0BD5]@0xffff ff7f86bdf000->0xffffff7f86bf6fff
dependency: com.apple.iokit.IOUSBFamily(5.4.0)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffff ff7f868c8000
dependency: com.apple.iokit.IOPCIFamily(2.7.2)[B1B77B26-7984-302F-BA8E-544DD3D75E73]@0xffff ff7f86850000
com.caiaq.driver.NIUSBMaschineControllerDriver(2.5.2)[00000000-0000-0000-0000-0 00000000000]@0xffffff7f8692a000->0xffffff7f8695ffff
dependency: com.apple.iokit.IOAudioFamily(1.8.9fc10)[0616A409-B8AF-34AC-A27A-F99939D8BD48]@ 0xffffff7f86892000
dependency: com.apple.iokit.IOUSBFamily(5.4.0)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffff ff7f868c8000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
12C60
Kernel version:
Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
Kernel UUID: 69A5853F-375A-3EF4-9247-478FD0247333
Kernel slide: 0x0000000006000000
Kernel text base: 0xffffff8006200000
System model name: iMac12,2 (Mac-942B59F58194171B)
System uptime in nanoseconds: 7066338561112
last loaded kext at 35843970927: com.apple.driver.AppleBluetoothMultitouch 75.15 (addr 0xffffff7f87faf000, size 77824)
last unloaded kext at 103423399316: com.apple.driver.AppleUSBUHCI 5.2.5 (addr 0xffffff7f86b93000, size 65536)
loaded kexts:
com.digidesign.mbox2.driver 9.0f4
com.caiaq.driver.NIUSBMaschineControllerDriver 2.5.2
com.apple.driver.AppleBluetoothMultitouch 75.15
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AudioAUUC 1.60
com.apple.iokit.IOBluetoothSerialManager 4.0.9f33
com.apple.driver.AGPM 100.12.69
com.apple.driver.AppleMikeyHIDDriver 122
com.apple.driver.AppleHDA 2.3.1f2
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.ApplePolicyControl 3.2.11
com.apple.driver.AppleLPC 1.6.0
com.apple.filesystems.autofs 3.0
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.kext.AMDFramebuffer 8.0.0
com.apple.AMDRadeonAccelerator 1.0.0
com.apple.driver.AppleBacklight 170.2.3
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.driver.AppleMikeyDriver 2.3.1f2
com.apple.driver.AppleSMCLMU 2.0.2d0
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleIntelHD3000Graphics 8.0.0
com.apple.driver.AppleMCCSControl 1.0.33
com.apple.driver.AppleIntelSNBGraphicsFB 8.0.0
com.apple.driver.AppleIRController 320.15
com.apple.iokit.SCSITaskUserClient 3.5.1
com.apple.driver.AppleUSBCardReader 3.1.0
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.2.2
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.driver.AppleUSBHub 5.2.5
com.apple.driver.AppleFWOHCI 4.9.6
com.apple.iokit.AppleBCM5701Ethernet 3.2.5b3
com.apple.driver.AppleAHCIPort 2.4.1
com.apple.driver.AirPort.Atheros40 600.70.23
com.apple.driver.AppleUSBEHCI 5.4.0
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleACPIButtons 1.6
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.6
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.driver.AppleMultitouchDriver 235.28
com.apple.driver.AppleBluetoothHIDKeyboard 165.5
com.apple.driver.IOBluetoothHIDDriver 4.0.9f33
com.apple.driver.AppleHIDKeyboard 165.5
com.apple.iokit.IOSerialFamily 10.0.6
com.apple.driver.DspFuncLib 2.3.1f2
com.apple.driver.AppleUSBAudio 2.9.0f6
com.apple.iokit.IOSurface 86.0.3
com.apple.iokit.IOBluetoothFamily 4.0.9f33
com.apple.kext.triggers 1.0
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.iokit.IOAcceleratorFamily 19.0.26
com.apple.iokit.IOAudioFamily 1.8.9fc10
com.apple.kext.OSvKernDSPLib 1.6
com.apple.driver.AppleGraphicsControl 3.2.11
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.kext.AMD6000Controller 8.0.0
com.apple.kext.AMDSupport 8.0.0
com.apple.driver.AppleHDAController 2.3.1f2
com.apple.iokit.IOHDAFamily 2.3.1f2
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.IOPlatformPluginFamily 5.2.0d16
com.apple.iokit.IONDRVSupport 2.3.5
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.AppleSMC 3.1.4d2
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.driver.AppleThunderboltEDMSink 1.1.8
com.apple.driver.AppleThunderboltEDMSource 1.1.8
com.apple.iokit.IOGraphicsFamily 2.3.5
com.apple.driver.AppleThunderboltDPOutAdapter 1.8.5
com.apple.driver.AppleThunderboltDPInAdapter 1.8.5
com.apple.driver.AppleThunderboltDPAdapterFamily 1.8.5
com.apple.driver.AppleThunderboltPCIDownAdapter 1.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOUSBHIDDriver 5.2.5
com.apple.iokit.IOAHCISerialATAPI 2.5.0
com.apple.iokit.IOSCSIBlockCommandsDevice 3.5.1
com.apple.iokit.IOUSBMassStorageClass 3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.1
com.apple.driver.AppleUSBMergeNub 5.2.5
com.apple.driver.AppleUSBComposite 5.2.5
com.apple.iokit.IOUSBUserClient 5.2.5
com.apple.driver.AppleThunderboltNHI 1.6.0
com.apple.iokit.IOThunderboltFamily 2.1.1
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOEthernetAVBController 1.0.2b1
com.apple.iokit.IOAHCIFamily 2.2.1
com.apple.iokit.IO80211Family 500.15
com.apple.iokit.IONetworkingFamily 3.0
com.apple.iokit.IOUSBFamily 5.4.0
com.apple.iokit.IOHIDFamily 1.8.0
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 220
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.DiskImages 344
com.apple.iokit.IOStorageFamily 1.8
com.apple.driver.AppleKeyStore 28.21
com.apple.driver.AppleACPIPlatform 1.6
com.apple.iokit.IOPCIFamily 2.7.2
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0
Model: iMac12,2, BootROM IM121.0047.B1E, 4 processors, Intel Core i5, 2.7 GHz, 12 GB, SMC 1.72f2
Graphics: AMD Radeon HD 6770M, AMD Radeon HD 6770M, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1333 MHz, 0x02FE, 0x45424A3230554638424353302D444A2D4620
Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1333 MHz, 0x02FE, 0x45424A3230554638424353302D444A2D4620
Memory Module: BANK 0/DIMM1, 4 GB, DDR3, 1333 MHz, 0x01BA, 0x202020202020202020202020202020202020
Memory Module: BANK 1/DIMM1, 4 GB, DDR3, 1333 MHz, 0x01BA, 0x202020202020202020202020202020202020
AirPort: spairport_wireless_card_type_airport_extreme (0x168C, 0x9A), Atheros 9380: 4.0.70.23-P2P
Bluetooth: Version 4.0.9f33 10885, 2 service, 18 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: ST31000528AS, 1 TB
Serial ATA Device: HL-DT-STDVDRW GA32N
USB Device: FaceTime HD Camera (Built-in), apple_vendor_id, 0x850b, 0xfa200000 / 3
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfa100000 / 2
USB Device: Axiom 61, 0x0763 (M-Audio), 0x202e, 0xfa120000 / 6
USB Device: Maschine Controller, 0x17cc, 0x0808, 0xfa130000 / 5
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 4
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8215, 0xfa111000 / 7
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfd100000 / 2
USB Device: Mbox 2, 0x0dba, 0x3000, 0xfd140000 / 5
USB Device: My Passport 0730, 0x1058 (Western Digital Technologies, Inc.), 0x0730, 0xfd130000 / 6
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0xfd120000 / 4
USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0xfd110000 / 3here is another one this one made my computer restart itself
Interval Since Last Panic Report: 105935 sec
Panics Since Last Report: 7
Anonymous UUID: 84387C31-EAF1-E5E2-8362-4FA69C1C8FCD
Wed Mar 13 19:41:17 2013
panic(cpu 1 caller 0xffffff802eeb7bd5): Kernel trap at 0xffffff802f1ec05a, type 13=general protection, registers:
CR0: 0x000000008001003b, CR2: 0x0000000014767000, CR3: 0x000000003186c000, CR4: 0x00000000000606e0
RAX: 0xffefff7faf7f45e0, RBX: 0xffffff7faf7f69b0, RCX: 0x0000000000000000, RDX: 0x0000000000000000
RSP: 0xffffff818fb13e00, RBP: 0xffffff818fb13e10, RSI: 0xffffff7faf7f69b0, RDI: 0xffffff804a07a000
R8: 0x0000000000000000, R9: 0x0000000000000200, R10: 0x0000000000000000, R11: 0x0000000000000200
R12: 0x0000000000653855, R13: 0x0000000000000000, R14: 0xffffff804a07a000, R15: 0x0000000000000000
RFL: 0x0000000000010286, RIP: 0xffffff802f1ec05a, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000014767000, Error code: 0x0000000000000000, Fault CPU: 0x1
Backtrace (CPU 1), Frame : Return Address
0xffffff818fb13aa0 : 0xffffff802ee1d626
0xffffff818fb13b10 : 0xffffff802eeb7bd5
0xffffff818fb13ce0 : 0xffffff802eece4ed
0xffffff818fb13d00 : 0xffffff802f1ec05a
0xffffff818fb13e10 : 0xffffff7faf7e897d
0xffffff818fb13eb0 : 0xffffff7faf7e8d87
0xffffff818fb13ed0 : 0xffffff7faf7e2f1b
0xffffff818fb13ef0 : 0xffffff802f2472a8
0xffffff818fb13f30 : 0xffffff802f245daa
0xffffff818fb13f80 : 0xffffff802f245ed9
0xffffff818fb13fb0 : 0xffffff802eeb26b7
Kernel Extensions in backtrace:
com.apple.driver.AppleUSBEHCI(5.4)[E4CA8E89-01B4-3A74-A46F-31A917AD0BD5]@0xffff ff7faf7df000->0xffffff7faf7f6fff
dependency: com.apple.iokit.IOUSBFamily(5.4.0)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffff ff7faf4c8000
dependency: com.apple.iokit.IOPCIFamily(2.7.2)[B1B77B26-7984-302F-BA8E-544DD3D75E73]@0xffff ff7faf450000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
12C60
Kernel version:
Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
Kernel UUID: 69A5853F-375A-3EF4-9247-478FD0247333
Kernel slide: 0x000000002ec00000
Kernel text base: 0xffffff802ee00000
System model name: iMac12,2 (Mac-942B59F58194171B)
System uptime in nanoseconds: 8785690599041
last loaded kext at 207347237886: com.apple.driver.AppleUSBCDC 4.1.22 (addr 0xffffff7fb11af000, size 16384)
last unloaded kext at 312551064596: com.apple.driver.AppleUSBCDC 4.1.22 (addr 0xffffff7fb11af000, size 12288)
loaded kexts:
com.digidesign.mbox2.driver 9.0f4
com.caiaq.driver.NIUSBMaschineControllerDriver 2.5.2
com.apple.driver.AppleBluetoothMultitouch 75.15
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.iokit.IOBluetoothSerialManager 4.0.9f33
com.apple.driver.AudioAUUC 1.60
com.apple.driver.AppleHDA 2.3.1f2
com.apple.driver.AGPM 100.12.69
com.apple.driver.AppleMikeyHIDDriver 122
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.ApplePolicyControl 3.2.11
com.apple.driver.AppleMikeyDriver 2.3.1f2
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.kext.AMDFramebuffer 8.0.0
com.apple.driver.AppleSMCLMU 2.0.2d0
com.apple.driver.AppleBacklight 170.2.3
com.apple.driver.AppleMCCSControl 1.0.33
com.apple.AMDRadeonAccelerator 1.0.0
com.apple.filesystems.autofs 3.0
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.AppleIntelHD3000Graphics 8.0.0
com.apple.driver.AppleIntelSNBGraphicsFB 8.0.0
com.apple.driver.AppleIRController 320.15
com.apple.iokit.SCSITaskUserClient 3.5.1
com.apple.driver.AppleUSBCardReader 3.1.0
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.2.2
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.driver.AppleUSBHub 5.2.5
com.apple.driver.AppleFWOHCI 4.9.6
com.apple.driver.AppleAHCIPort 2.4.1
com.apple.iokit.AppleBCM5701Ethernet 3.2.5b3
com.apple.driver.AirPort.Atheros40 600.70.23
com.apple.driver.AppleUSBEHCI 5.4.0
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AppleACPIButtons 1.6
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.6
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.driver.AppleMultitouchDriver 235.28
com.apple.driver.AppleBluetoothHIDKeyboard 165.5
com.apple.driver.IOBluetoothHIDDriver 4.0.9f33
com.apple.driver.AppleHIDKeyboard 165.5
com.apple.iokit.IOSerialFamily 10.0.6
com.apple.driver.DspFuncLib 2.3.1f2
com.apple.iokit.IOSurface 86.0.3
com.apple.iokit.IOBluetoothFamily 4.0.9f33
com.apple.driver.AppleUSBAudio 2.9.0f6
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.AppleHDAController 2.3.1f2
com.apple.iokit.IOHDAFamily 2.3.1f2
com.apple.driver.AppleGraphicsControl 3.2.11
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.iokit.IOAcceleratorFamily 19.0.26
com.apple.kext.AMD6000Controller 8.0.0
com.apple.kext.AMDSupport 8.0.0
com.apple.kext.triggers 1.0
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleSMC 3.1.4d2
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.AppleThunderboltEDMSink 1.1.8
com.apple.driver.AppleThunderboltEDMSource 1.1.8
com.apple.driver.IOPlatformPluginFamily 5.2.0d16
com.apple.iokit.IONDRVSupport 2.3.5
com.apple.iokit.IOGraphicsFamily 2.3.5
com.apple.iokit.IOAudioFamily 1.8.9fc10
com.apple.kext.OSvKernDSPLib 1.6
com.apple.driver.AppleThunderboltDPOutAdapter 1.8.5
com.apple.driver.AppleThunderboltDPInAdapter 1.8.5
com.apple.driver.AppleThunderboltDPAdapterFamily 1.8.5
com.apple.driver.AppleThunderboltPCIDownAdapter 1.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOUSBHIDDriver 5.2.5
com.apple.iokit.IOAHCISerialATAPI 2.5.0
com.apple.iokit.IOSCSIBlockCommandsDevice 3.5.1
com.apple.iokit.IOUSBMassStorageClass 3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.1
com.apple.driver.AppleUSBMergeNub 5.2.5
com.apple.driver.AppleUSBComposite 5.2.5
com.apple.driver.AppleThunderboltNHI 1.6.0
com.apple.iokit.IOThunderboltFamily 2.1.1
com.apple.iokit.IOUSBUserClient 5.2.5
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOAHCIFamily 2.2.1
com.apple.iokit.IOEthernetAVBController 1.0.2b1
com.apple.iokit.IO80211Family 500.15
com.apple.iokit.IONetworkingFamily 3.0
com.apple.iokit.IOUSBFamily 5.4.0
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOHIDFamily 1.8.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 220
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.DiskImages 344
com.apple.iokit.IOStorageFamily 1.8
com.apple.driver.AppleKeyStore 28.21
com.apple.driver.AppleACPIPlatform 1.6
com.apple.iokit.IOPCIFamily 2.7.2
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0
Model: iMac12,2, BootROM IM121.0047.B1E, 4 processors, Intel Core i5, 2.7 GHz, 12 GB, SMC 1.72f2
Graphics: AMD Radeon HD 6770M, AMD Radeon HD 6770M, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1333 MHz, 0x02FE, 0x45424A3230554638424353302D444A2D4620
Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1333 MHz, 0x02FE, 0x45424A3230554638424353302D444A2D4620
Memory Module: BANK 0/DIMM1, 4 GB, DDR3, 1333 MHz, 0x01BA, 0x202020202020202020202020202020202020
Memory Module: BANK 1/DIMM1, 4 GB, DDR3, 1333 MHz, 0x01BA, 0x202020202020202020202020202020202020
AirPort: spairport_wireless_card_type_airport_extreme (0x168C, 0x9A), Atheros 9380: 4.0.70.23-P2P
Bluetooth: Version 4.0.9f33 10885, 2 service, 18 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: ST31000528AS, 1 TB
Serial ATA Device: HL-DT-STDVDRW GA32N
USB Device: FaceTime HD Camera (Built-in), apple_vendor_id, 0x850b, 0xfa200000 / 3
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfa100000 / 2
USB Device: Axiom 61, 0x0763 (M-Audio), 0x202e, 0xfa130000 / 6
USB Device: Maschine Controller, 0x17cc, 0x0808, 0xfa120000 / 5
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 4
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8215, 0xfa111000 / 7
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfd100000 / 2
USB Device: Mbox 2, 0x0dba, 0x3000, 0xfd140000 / 5
USB Device: My Passport 0730, 0x1058 (Western Digital Technologies, Inc.), 0x0730, 0xfd130000 / 6
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0xfd120000 / 4
USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0xfd110000 / 3 -
Problem with Fader Banks and Channel in MCU PRO with Logic Pro X
I purchased a Mackie Control Universal Pro earlier this week, and I have talked with Mackie support techs twice and they have not been able to help me. My problem is that everything seems to work well with Logic X talking with the MCU with the exeption that the Fader Banks function will not move left to channels 1-8, they are stuck at channel 9-16, and will move to the right on to 17-24 and so on, but it doesnt move to 1-8 when the left fader bank motor is pressed. However when you toggle tany channel 1-8 levers on the computer screen, the corresponding lever on the Mackie goes up and down, but the reverse does not occur. The Mackie folks say this is a problem with Logic Pro X, not the MCU. Perhaps they are correct, because I still have Logic Express on my Mac and when I close Logic X and Open Logic Express the fader banks move perfectly from 1-8, 9-16, and so on as do the tracks. My computer is update with Mavericks.
I would appreciate any help! I am not a techie, an old guy who used to record on 4 track computers, and want to get away from a mouse control, but I'm going to take the Mackie MCU back if I cant get this straight, I've spent a lot of time on this. Help!thank you Pete in Denver, I actually made some progress today, in setting up the control surface of the Logic Pro Control Surfaces Support Manual, around page sixteen gave me a partial answer. I had the Mackie icon first, then the Logic Control, and it said to drag and drop the preferred icon to the left or first place. that solved my not being able to access channels 1-8, I was able to press the fader bank left button and - voila!. so that saved my initial problem, but I still have some issues in moving faders and banks in existing projects, some tracks show up lit up in the tan colors others don't, but that is probably due to the way i would move tracks around once I received tracks on drop box from a friend and created new tracks, and I changed a lot of the order of the tracks. ANyway. I did make progress. Thanks!
-
Hi. I'm new to this community but would really appreciate some help.
I'm struggling to find a 61 key midi keyboard which works properly with Logic Pro X.
I was looking into getting either the M-Audio Axiom 61 or Novation Impulse 61 but all I can find on google etc. is people saying they don't work properly.
Has anybody got a 61 key which works seamlessly with Pro X?
Any help would be much appreciated.
Thanks.To "The Art Of Sound"
Hi. I doing next.
1. I create new project
2. I select Yamaha Grand Piano
3. I play something in "live" mode. All is ok
4. I play something in "Rec" mode. All is ok
5. I record second track with the same instrument, with Yamaha Grand Piano. All is ok
6. I record third track with Yamaha Grand Piano. All is ok again.
7. Now I muting first or second track and... third track plays wrong notes! I unmute first track, but third track still to play wrong notes! Why???
Ok. I continue experiment with created project. I have three Yamaha grand Piano tracks and I creating new software instrument and assing Hovering Machine to it. I try to play in "live" mode something. And I get interesting effect. If I play short notes (sixteens, for example), I can play for one minute without problem. And Logic Pro X starts to play wrong notes after this time delay.
If I start to press chord notes without breaking, Logic Pro X plays for 15-30 secounds normally and starts to play wrong notes them.
Well. I turn off all plugins and effects from instruments. But Logic Pro X countinues to play wrong notes!
I experimented with NI Kontakt 5. Kontakt plays wrong notes!
I experimented with LUSH-101 plugin and minimoog. This two instruments play correct notes always!!! WHY????
Why some instruments play wrong notes and other instruments play correct notes in the same project?
I wrote wrong in my previous post. I got this problem with Logic Pro X 10.0.3 update.
Actually I have serious problem now. I opened projects created in Logic Pro X early and I have this problem in ALL projects. This's commercial projects and my partners asked me already about release date... What must I answer? -
Hello,having a problem with Logic 9 on a Mac Pro.Working on a lenghty song and apparently session got corrupted.Doesnt let me export tracks,program crashes.Already tried start brand new session with the tracks imported into it but still wont export.Suggestions?
Thanks, Ian. Yeah, that's how I do it now...or with the controls in the left side pane. Still, I would have liked that quick on-the-spot edit capability...especially while sketching.
Ian Turner wrote:
Sorry Mark, you are out of luck as it does not do that - it works the same as L8. The way I would achieve that with more accuracy and control would be to route all the tracks you want to fade to a Bus then use volume automation on the bus. To do this you will need to add a standard audio track, then re-assign it using (Control Click on the track header) to the Bus track. You can then automate volume/plugins etc on the Bus track.
Ian -
Line input problem with Logic X, No issues Logic Pro
I use the line input on my 2011 Imac to record audio from my piano keyboard. When using LOGIC X there is no sound coming through the speakers, but with Logic Pro 9 I have no issues. I tested with new projects, ect but was unable to get to work.
In both Logic Pro and Logic X I have made an audio track and made sure input monitoring is on. I made sure volume was sufficient. I have tried to fix this to no avail and was thinking about bringing to apple store, but this appreasrs to be some sort of logic x bug (or I am missing something). Any help is appreciated as this is very frustrating.
BrianI think you're missing something.
http://help.apple.com/logicpro/mac/10/#lgcpbb81aca5
You have to configure each program top to bottom, go to the above link and make sure all your settings are correct. (the won't necessarily match the pic)
Look at your Logic 9 settings Preferences/Audio and then set up Logic X the same way. -
Mainstage still packaged with Logic Pro?
So I wanted to get the jam packs to use in garageband but it turns out they're all in Mainstage 2 now. I am planning on upgrading to logic in a year or so and I thought mainstage came packaged with it. Do you have to purchase them separately now? Logic express used to be $199 and Logic Pro was $499. What happened to that? Are all the plugins and third party effects gone now? What is going on?
Mainstage is no longer packaged with Logic Pro.
It can be downloaded separately (with all of its JamPacky goodness) for $29.99.
Logic Express was cancelled as Logic Pro now costs what Logic Express used to cost: $199. -
Install on MacBook Pro end of 2011 with logic Pro 9.1.8 and Apogee GIO interface guitar
The wha wha pedal work well with GarageBand but not working with Logic Pro
Only the red light turning on and off at the screnn of the MBPro and on my Apogee GIO (Guitar Interface Midi) switch button but the effect wha wha won't work.
HOPE YOU UNDERSTAND MY ENGLISHPancenter...
Yes... but I have come across some setups that came with a native SL (and even one Lion!) installation.. that somehow had a corrupted or older Prokit installed for some unknown reason... and given it's a quick fix to try.. I thought I'd mention it..
I frankly don't think it is entirely a Prokit issue itself, but it wouldn't do any harm to try and install v7 just in case it is part of the problem...
+1 on the UAD stuff....
Also, at the time it crashed... according to the logs...the OP was running Ableton Live at the same time, presumably rewired with Logic... so add all that together with UAD plugins... and that's quite a load on the system...
Finally in thread 32 there is a weird exception msg relating to the Trash2 plugin.. that I haven't seen before...
Thread 32:
0 libSystem.B.dylib
0x94c29afa mach_msg_trap + 10
1 libSystem.B.dylib
0x94c2a267 mach_msg + 68
2 ...tope.audioplugins.AU.Trash2
0x667bd57a catch_exception_raise + 250
3 libSystem.B.dylib
0x94c57259 _pthread_start + 345
4 libSystem.B.dylib
0x94c570de thread_start + 34
That might be nothing... but as i said, I haven't seen that one before and given what else is going on.. it might be involved too... or nothing to do with that at all! -
Can I connect every USB-Audiointerface with Logic Pro?
Hello there,
please forgive me, if my english isn't so well.
So, my "problem": I actually informated me over Logic Pro X, and by the provided Audiointerfaces, I didn't saw my Audiointerface.
But - Can I simply connect a USB-Audiointerface with Logic Pro?
So, hope you understand me,
Best wishes, "toasbrot_55" (sorry for that name, i don't know when I did chosen this name)All Mac OS compatible audio interfaces work with Logic, and almost all USB interfaces are Mac compatible. So it depends on which interface you have (make and model), and which Mac OS version you use.
Maybe you are looking for
-
How do I use an Older iPhoto Library with an Updated iPhoto application?
Hey Everyone! I seem to be stuck. My MacBook Pro was running OS X Lion and I needed to reset the computer. When I was exporting the photos, it would stop and say it was not able to export the photos. So I just copied the actual file from the Pictures
-
i am populating data to a table. when i click ant row in the table that row data should be displayed in the panel below that of the table panel in correspondin text fields..... how do i do this ............. can anybody please help
-
Reader 9.3.3 Breaks forms with mailto button
We have been testing Reader 9.3.3 and have just discovered that it breaks one of our online forms that have a mailto button. We receive an error: Security Block: Acrobat does not allow connection to: mailto:maibox name It works just fine on any prev
-
IAS 9.0.4 for AIX
Hi all, where i can found IAS 9.0.4 for AIX to download?
-
Hi all, I have 2 ods'es ods1 and ods2. based on some value for a particular field in ods1 i need to update in ods2. basically i need to lookup in ods1 and update in ods2. any sample routine of how to solve this. thanks.